JET 506601 Manuel utilisateur

EN

JET

427 New Sanford Road

La Vergne, Tennessee 37086

Ph: 1.800.274.6848

www.jettools.com

Part No. M-506601

Edition 1 03/2016

IN572000AV 2/16

Model: JCP-601

Stationary Air Compressor

Operating Instructions and Parts Manual

Please read and save these instructions. Read carefully before attempting to

assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply

with instructions could result in personal injury and/or property damage! Retain

instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to

this manual or file it for safekeeping.

Model #: _______________________

Serial #: ________________________

Purchase Date: _________________

REGISTER YOUR PRODUCT ONLINE NOW!

http://www.jettools.com/us/en/service-and-support/warranty/registration/

READ AND FOLLOW ALL INSTRUCTIONS • SAVE THESE INSTRUCTIONS • DO NOT DISCARD

For parts, product & service information

visit www.jettools.com

JET

427 New Sanford Road

La Vergne, TN 37086

Phone: 1.800.274.6848

1

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

BEFORE YOU BEGIN

Introduction

Air compressor units are intended to provide compressed air to power pneumatic tools, operate spray guns and

supply air for pneumatic valves and actuators. The pumps supplied with these units have oil lubricated bearings.

A small amount of oil carryover is present in the compressed air stream. Applications requiring air free of oil vapor

should have the appropriate filters installed. The air compressor units are to be mounted per the instructions

provided on a solid floor. Any other use of these units will void the warranty and the manufacturer will not be

responsible for problems or damages resulting from such misuse.

QUICK REFERENCE

Recommended Oil (2 Options)

Single viscosity SAE 30 ISO100 nondetergent compressor oil.

10W30 synthetic oil such as Mobil 1

®

.

Oil Capacity

Approximately 8.5 oz.

UNPACKING

Do not lift or move unit without appropriately rated equipment. Be sure

the unit is securely attached to lifting device used. Do not lift unit by holding onto tubes or

coolers. Do not use unit to lift other attached equipment.

After unpacking the unit, inspect carefully for any damage that may have occurred during transit. Check for

loose, missing or damaged parts. Check to be sure all supplied accessories are enclosed with the unit. In case of

questions, damaged or missing parts, please visit www.jettools.com for customer assistance.

Do not operate unit if damaged during shipping, handling or use. Damage

may result in bursting and cause injury or property damage.

Required Items - Not Included

• Oil

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION GETTING STARTED

2

SAFETY /

SPECIFICATIONS

GENERAL SAFETY INSTRUCTIONS

Safety Guidelines

This manual contains information that is very important to know and understand. This information is provided for

SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following

symbols.

Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death

or serious injury.

Warning indicates a potentially hazardous situation which, if not avoided, COULD result in

death or serious injury.

Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor

or moderate injury.

Notice indicates important information, that if not followed, may cause damage to equipment.

IMPORTANT: Information that requires special attention.

Safety Symbols

The following Safety Symbols appear throughout this manual to alert you to important safety hazards and

precautions.

California Proposition 65

This product or its power cord may contain chemicals known to the State

of California to cause cancer and birth defects or other reproductive harm. Wash hands after

handling.

You can create dust when you cut, sand, drill or grind materials such as wood,

paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to

cause cancer, birth defects, or other reproductive harm. Wear protective gear.

Important Safety Information

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the

product described. Protect yourself and others by observing all safety information. Failure to comply with instructions

could result in personal injury and/or property damage! Retain instructions for future reference.

This manual contains important safety, operational and maintenance information. If you have any questions,

please visit www.jettools.com for customer assistance.

Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.) used

make up a high pressure pumping system, the following safety precautions must be observed at all times:

Risk of

Moving

Parts

Risk of

Hot Parts

Risk of

Explosion

Risk of

Fumes

Risk of

Pressure

Risk of

Shock

MANUAL

Read

Manual

First

Risk of

Fire

Wear Eye

and Mask

Protection

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION GETTING STARTED

3

SAFETY /

SPECIFICATIONS

Important Safety Information (Continued)

BREATHABLE AIR WARNING

This compressor/pump is not equipped and should not be used “as is” to supply breathing quality

air. For any application of air for human consumption, the air compressor/pump will need to be

fitted with suitable in-line safety and alarm equipment. This additional equipment is necessary to

properly filter and purify the air to meet minimal specifications for Grade D breathing as described

in Compressed Gas Association Commodity Specification G 7.1, OSHA 29 CFR 1910. 134, and/or

Canadian Standards Associations (CSA).

DISCLAIMER OF WARRANTIES

In the event the compressor is used for the purpose of breathing air application and proper in-line

safety and alarm equipment is not simultaneously used, existing warranties shall be voided, and the

manufacturer disclaims any liability whatsoever for any loss, personal injury or damage.

General Safety

• Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper

use of the equipment.

• Follow all local electrical and safety codes as well as the United States National Electrical Codes (NEC) and

Occupational Safety and Health Act (OSHA).

• Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.

• Keep visitors away and NEVER allow children in the work area.

• Wear safety glasses and use hearing protection when operating the unit.

• Do not stand on or use the unit as a handhold.

• Before each use, inspect compressed air system and electrical components for signs of damage,

deterioration, weakness or leakage. Repair or replace defective items before using.

• Check all fasteners at frequent intervals for proper tightness.

Motors, electrical equipment and controls can cause electrical

arcs that will ignite a flammable gas or vapor. Never operate or repair in or near a flammable

gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor.

Never operate compressor without a beltguard. This unit can

start automatically without warning. Personal injury or property damage could occur from

contact with moving parts.

• Do not wear loose clothing or jewelry that will get caught in the moving parts of the unit.

Compressor parts may be hot even if the unit is stopped.

• Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or burns.

• If the equipment should start to vibrate abnormally, STOP the engine/motor and check immediately for the

cause. Vibration is generally an indication of trouble.

• To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.

An ASME code safety relief valve with a setting no higher than the Maximum

Allowable Working Pressure (MAWP) of the tank MUST be installed in the air lines or in the tank

for this compressor. The ASME safety valve must have sufficient flow and pressure ratings to protect the pressurized

components from bursting. The flow rating can be found in the parts manual. The safety valve in the intercooler does

not provide system protection.

See compressor

specifications for maximum operating pressure. Do not operate

with pressure switch or pilot valves set higher than the maximum operating pressure.

Maximum operating pressure is 140 psi for single stage compressors. Do not

operate with pressure switch or pilot valves set higher than 140 psi (single stage).

• Never attempt to adjust ASME safety valve. Keep safety valve free from paint and other accumulations.

MANUAL

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION GETTING STARTED

4

SAFETY /

SPECIFICATIONS

Important Safety Information (Continued)

Never use plastic (PVC) pipe for compressed air. Serious injury or death could

result.

Never attempt to repair or modify a tank! Welding, drilling or any other modification will weaken

the tank resulting in damage from rupture or explosion. Always replace worn, cracked or

damaged tanks.

Drain liquid from tank daily.

• Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and inspect

periodically for unsafe conditions such as rust formation and corrosion.

• Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture

or depressurizing the compressor system.

Spraying Precautions

Do not spray flammable materials in vicinity of open flame or near ignition sources including

the compressor unit.

• Do not smoke when spraying paint, insecticides, or other flammable substances.

• Use a face mask/respirator when spraying and spray in a well ventilated area to prevent health and fire

hazards.

• Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the

spraying area as possible to minimize overspray accumulation on the compressor.

• When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical

manufacturer.

Save These Instructions

Do Not Discard

The DANGER, WARNING, CAUTION, and NOTICE notifications and instructions in this manual cannot

cover all possible conditions and situations that may occur. It must be understood by the operator that

caution is a factor which cannot be built into this product, but must be supplied by the operator.

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION GETTING STARTED

5

Getting To Know Your Compressor

SAFETY /

SPECIFICATIONS

Figure 1 - Vertical Unit Identification

Air Filter

Tank Pressure

Gauge

Manual Tank Drain

Pressure Switch

Safety Relief Valve

Compressor Pump

Unloader Tube

Discharge Tube

Motor

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION GETTING STARTED

6

SAFETY /

SPECIFICATIONS

DIMENSIONS

BOLT DOWN PATTERN

JCP-601

Stock Number 506601

Motor HP 3.2

Power 208-230V

Phase 1

Displacement CFM 12.2

Air Delivery CFM @ 90 PSI 10.2

Air Delivery CFM @ 135 PSI 9.8

Max PSI 135

Pump RPM 1020

Tank Capacity 60 gallons

Unit Weight 255 lbs

Amp Draw 14.5

Max Duty Cycle 75%

Tank Outlet 1/4 in. NPT

Tank MAWP 175 PSI

JCP-601

Length 23 inches

Width 25 inches

Height 66 inches

24.00

120.00

6.0

12

10.39

in.

o

in.

10.39

in.

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

SAFETY /

SPECIFICATIONS GETTING STARTED

7

ASSEMBLY /

INSTALLATION

INSTALLATION INSTRUCTIONS

Disconnect, tag and lock out power source then release all pressure from the system before

attempting to install, service, relocate or perform any maintenance.

Do not lift or move unit without appropriately rated equipment. Be sure the unit is securely

attached to lifting device used. Do not lift unit by holding onto tubes or coolers. Do not use unit

to lift other attached equipment.

Never use the wood shipping skids for mounting the compressor.

Picking the Location

Install and operate unit at least 18 inches from any obstructions in a

clean, well ventilated area. The surrounding air temperature should

not exceed 100° F. This will ensure an unobstructed flow of air to

cool compressor and allow adequate space for maintenance.

Do not locate the compressor air inlet

near steam, paint spray, sandblast areas or any

other source of contamination.

NOTE: If compressor operates in a hot, moist environment, supply

compressor pump with clean, dry outside air. Supply air should be

piped in from external sources.

Tank Mounting

The tank should be bolted into a flat, even, concrete floor or on a

separate concrete foundation. Vibration isolators should be used

between the tank leg and the floor.

When using isolator pads, do not draw bolts tight. Allow the pads

to absorb vibrations. When isolators are used, a flexible hose or

coupling should be installed between the tank and service piping.

Failure to properly install the tank can lead to

cracks at the welded joints and possible

bursting.

Piping

Never use plastic (PVC) pipe for

compressed air. Serious injury or death could

result.

Any tube, pipe or hose connected to the unit must be able to

withstand the temperature generated and retain the pressure. All

pressurized components of the air system must have a pressure rating of 200 psi or higher. Incorrect selection

and installation of any tube, pipe or hose could result in bursting and injury. Connect piping system to tank using

the same size fitting as the discharge port.

Minimum Pipe Size For Compressed Air Line

CFM

LENGTH OF PIPING SYSTEM

25 FEET 50 FEET 100 FEET 250 FEET

10 1/2 inch 1/2 inch 3/4 inch 3/4 inch

20 3/4 inch 3/4 inch 3/4 inch 1 inch

40 3/4 inch 1 inch 1 inch 1 inch

60 3/4 inch 1 inch 1 inch 1 inch

100 1 inch 1 inch 1 inch 1-1/4 inch

Figure 3 - Isolator Pad

≥ 18

inches

≥ 18

inches

≥ 18

inches

Figure 2 - Location

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

SAFETY /

SPECIFICATIONS GETTING STARTED

8

ASSEMBLY /

INSTALLATION

INSTALLATION INSTRUCTIONS (CONTINUED)

Installing A Shut-Off Valve

A shut-off valve should be installed on the discharge port of the tank to control the

air flow out of the tank. The valve should be located between the tank and the piping

system.

Never install a shut-off valve between the compressor pump and

the tank. Personal injury and/or equipment damage may occur.

Never use reducers in discharge piping.

When creating a permanently installed system to distribute compressed air, find

the total length of the system and select pipe size from the chart on page 7. Bury

underground lines below the frost line and avoid pockets where condensation can

gather and freeze.

Apply air pressure to the piping installation and make sure all joints are free from leaks BEFORE underground

lines are covered. Before putting the compressor into service, find and repair all leaks in the piping, fittings and

connections.

Wiring

All wiring and electrical connections must be performed by a qualified electrician

familiar with induction motor controls. Installations must be in accordance with local and

national codes.

Overheating, short circuiting and fire damage will result from inadequate wiring.

Wiring must be installed in accordance with National Electrical Code and local codes and standards that have

been set up covering electrical apparatus and wiring. These should be consulted and local ordinances observed.

Be certain that adequate wire sizes are used, and that:

1. Service is of adequate ampere rating.

2. The supply line has the same electrical characteristics (voltage, cycles and phase) as the motor. Refer to

motor name plate for electrical ratings and specifications.

3. The line wire is the proper size and that no other equipment is operated from the same line. The chart gives

minimum recommended wire sizes for compressor installations.

Minimum Wire Size (Use 75°C Copper Wire)

Make sure voltage is correct with the motor wiring.

NOTE: If using 208 volts single phase, make sure the motor name plate states it is rated for 208 volts

single phase. 230 volt single phase motors do not work on 208 volts unless they have the 208 volt rating.

SINGLE PHASE

HP AMPS 230V

1-4 HP UP TO 22.0 10 AWG

5.0 8 AWG

Recommended wire sizes may be larger than the minimum set up by local ordinances. If so, the larger size

wire should be used to prevent excessive line voltage drop. The additional wire cost is very small compared

with the cost of repairing or replacing a motor electrically “starved” by the use of supply wires which are too

small.

Figure 4 - Shut-off Valve

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

SAFETY /

SPECIFICATIONS GETTING STARTED

9

ASSEMBLY /

INSTALLATION

INSTALLATION INSTRUCTIONS (CONTINUED)

Grounding

Improperly grounded electrical components are shock hazards. Make sure all the

components are properly grounded to prevent death or serious injury.

This product must be grounded. Grounding reduces the risk of electrical shock by providing an escape wire for

the electric current if short circuit occurs. This product must be installed and operated with a power cord or cable

that has a grounding wire.

Breakers and Fuses

The entire electrical system should be checked by a certified electrician. Time delay breakers and fuses are

required for this compressor. A tripped breaker or blown fuses may indicate a direct short to ground, high current

draw, improper wiring, incorrect fuse or breaker size and/or type. This needs to be evaluated by a certified

electrician.

Motor

Ground

L2

L1

Figure 5 - Wiring Diagram

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

SAFETY /

SPECIFICATIONS GETTING STARTED

10

ASSEMBLY /

INSTALLATION

INSTALLATION INSTRUCTIONS (CONTINUED)

Installing Air Inlet Filter

Screw supplied air inlet filter into inlet port of cast iron pump

as indicated in Figure 6.

Lubrication

This unit contains no oil.

Before operating compressor, fill to the

center of the sight gauge (see Figure 6).

Using any other type of oil may

shorten pump life and damage valves.

Recommended Oil (2 Options)

Single viscosity SAE 30 ISO100 nondetergent

compressor oil.

10W30 synthetic oil such as Mobil 1

®

.

Oil Capacity

Approximately 8.5 oz.

Fill the pump with oil to the center of the sight gauge using

oil fill opening (see Figure 6). Do NOT fill the pump through

the breather cap opening as this may cause oil to leak and

spray out during operation.

NOTE: Some residual oil may still be in the pump from

factory testing leaving a thin coat on the sight gauge;

however, there is not enough oil to operate the unit.

OPERATING INSTRUCTIONS

IMPORTANT: Check motor rotation before operating the

compressor.

All lubricated compressor pumps discharge some

condensed water and oil with the compressed air. Install

appropriate water/oil removal equipment and controls as

necessary for the intended application.

Failure to install appropriate

water/oil removal equipment may result in

damage to machinery or workpiece.

Guarding

The belt guard provided must be

installed before operating the unit.

All moving parts must be guarded. All electrical covers must be

installed before turning on the power.

Figure 6 - Lubrication

Oil Drain

Plug

Sight Gauge

Full

Low

Oil FIll

Area

Inlet Port

OPERATING INSTRUCTIONS (CONTINUED)

Recommended Break-In Period

The compressor should be run continuously at 90 PSI or lower for one hour to allow proper seating of the piston

rings.

1. Open drain cock completely and run the compressor for 60 minutes.

2. Turn off the compressor and close drain cock. The compressor is now ready for use.

If the compressor is run under humid conditions for short periods

of time, the humidity will condense in the crankcase and cause

the oil to look creamy. Oil contaminated by condensed water

will not provide adequate lubrication and must be changed

immediately. Using contaminated oil will damage bearings,

pistons, cylinders and rings and is not covered under warranty.

To avoid water condensation in the oil, periodically run the

compressor with tank pressure near 120 psi for single stage

compressors by opening the drain valve or an air valve connected

to the tank or hose. Run the pump for an hour at a time at least

once a week or more often if the condensation reoccurs.

IMPORTANT: Change oil after first 50 hours of operation and

every 200 hours afterwards.

Pressure Switch, Start - Stop

NOTE: Single stage compressors have a maximum operating pressure of 135 psi. Do not alter pressure settings

on control components above this limit.

The compressor unit starts and stops based on preset pressure switch settings of 105 psi cut-in and 135 psi

cut-out. The pressure switch contains an unloader which is a small valve that vents air to allow the motor to start

easily (see Figure 7).

The unloader valve on the pressure switch should hiss for a short period of time when the compressor shuts off.

This relieves the head and the exhaust tubing of any pressure and allows the compressor to start under no load.

Because compressors have high starting torque the unloader is necessary for proper starting of the compressor.

The check valve is a one way valve that keeps the air in the tank when the unit shuts off. The easiest way to

determine if the check valve is working properly is to make sure that the pressure switch unloader quits hissing

after the compressor shuts off. The hissing should last for several seconds and then quit.

Crankcase Breather

During severe operating conditions or initial start-up, some oil may accumulate at the crankcase breather

opening. This is normal and will diminish as the pump accumulates run time and the piston rings become fully

seated.

Draining Tank

Condensate must be drained from the tank daily, use

manual tank drain (see Figure 8).

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

SAFETY /

SPECIFICATIONS GETTING STARTED

11

ASSEMBLY /

INSTALLATION

Figure 8 - Manual Tank Drain

Figure 7 - Pressure Switch

Unloader

(behind pressure

switch)

Safety

Relief

TROUBLESHOOTING GUIDE

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

12

OPERATION

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Low discharge pressure 1. Air demand exceeds pump capacity 1. Reduce air demand or use a compressor with more

capacity.

2. Air leaks 2. Listen for escaping air. Apply soap solution to all

fittings and connections. Bubbles will appear at

points of leakage.Tighten or replace leaking fittings or

connections.

3. Restricted air intake 3. Clean the air filter element.

4. Blown gaskets 4. Replace any gaskets proven faulty on inspection.

5. Leaking or damaged valves 5. Remove head and inspect for valve breakage,

misaligned valves, damaged valve seats, etc. Replace

defective parts and reassemble.

Install a new head gasket

each time the head is removed

Pump overheating causes air

filter to melt

1. Insulating gasket between filter and

head is missing

1. Install gasket.

2. Broken valves/blown gasket 2. Replace valves or install new gasket.

Excessive noise (knocking) 1. Loose motor or compressor pulley 1. Loose motor or compressor pulleys are a very common

cause of compressors knocking. Tighten pulley clamp

bolts and set-screws.

2. Lack of oil in crankcase 2. Check for proper oil level; if low, check for possible

damage to bearings. Dirty oil can cause excessive

wear.

3. Worn connecting rod 3. Replace connecting rod. Maintain oil level and change

oil more frequently.

4. Worn piston pin bores 4. Remove piston assemblies from the compressor and

inspect for excess wear. Replace excessively worn

piston pin or pistons, as required. Maintain oil level and

change oil more frequently.

5. Piston hitting the valve plate 5. Remove the compressor head and valve plate and

inspect for carbon deposits or other foreign matter on

top of piston. Replace head and valve plate using new

gasket. See Lubrication section for recommended oil

6. Noisy check valve in compressor

system

6. Replace.

Do not disassemble check valve

with air pressure in tank

Large quantity of oil in the

discharge air

NOTE: In an oil lubricated

compressor there will always be

a small amount of oil in the air

stream.

1. Worn piston rings 1. Replace with new rings. Maintain oil level and change

oil more frequently.

2. Compressor air intake restricted 2. Clean filter. Check for other restrictions in the intake

system.

3. Excessive oil in compressor 3. Drain down to full level.

4. Wrong oil viscosity 4. Use Mobil 1

®

10W-30

Water in discharge air/tank 1. Normal operation. The amount of water

increases with humid weather

1. Drain tank more often. At least daily.

2. Add a filter to reduce the amount of water in the air line.

Motor hums and runs slowly or

not at all

1. Use of extension cord 1. Do not use an extension cord. Use longer air hose with

larger diameter.

2. Malfunctioning check valve or unloader

valve

2. Replace check valve, unloader valve or pressure

switch.

Do not disassemble check valve

with air pressure in tank

3. Low voltage 3. Check with volt meter, check reset switch on motor. If

reset switch trips repeatedly, find and correct the cause.

See next item.

4. Malfunctioning pressure switch -

contacts will not close

4. Repair or replace pressure switch.

TROUBLESHOOTING GUIDE (CONTINUED)

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

13

SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Reset mechanism cuts out

repeatedly or fuses blow

repeatedly

1. Too many devices on same circuit 1. Limit the circuit to the use of only the air compressor.

2. Incorrect fuse size or circuit breaker 2. Be sure that fuses or circuit breakers are rated properly.

3. Malfunctioning check valve 3. Replace check valve.

Do not disassemble check valve

with air pressure in tank

4. Pressure switch set too high 4. Adjust or replace.

5. Loose wiring 5. Check all electrical connections.

6. Malfunctioning motor 6. Replace motor.

Tank does not hold pressure

when compressors off and the

shut off valve is closed

1. Worn check valve 1. Replace check valve.

Do not disassemble check valve

with air pressure in tank

2. Check all connections and fittings for

leaks

2. Tighten.

3. Check tank for cracks or pin holes 3. Replace tank. Never repair a damaged tank.

Pressure switch continuously

blows air out the unloader valve

1. Malfunctioning check valve 1. Replace the check valve if the unloader valve bleeds off

constantly.

Do not disassemble check valve

with air pressure in tank

Pressure switch does not release

air when the unit shuts off

1. Malfunctioning unloader valve on

pressure switch

1. Replace the pressure switch if it does not release the

pressure for a short period of time when the unit shuts

off.

Do not disassemble pressure

switch with air pressure in tank

Excessive vibration 1. Loose fasteners 1. Tighten.

2. Belt needs replaced 2. Replace with correct size.

3. Belt alignment 3. Align flywheel and pulley.

TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

14

MAINTENANCE /

REPAIR

MAINTENANCE AND INSPECTION INSTRUCTIONS

Disconnect, tag and lock out power source then release all pressure from the system before

attempting to install, service, relocate or perform any maintenance.

In order to maintain efficient operation of the compressor system, check the air filter and oil level before each

use. The ASME safety valve should also be checked daily (see Figure 9). Pull ring on safety valve and allow the

ring to snap back to normal position. This valve automatically releases air if the tank pressure exceeds the preset

maximum. If air leaks after the ring has been released, or the valve is stuck and cannot be actuated by the ring,

the ASME safety valve must be replaced.

Do not tamper with the ASME safety valve.

Tank

Never attempt to repair or modify a tank! Welding, drilling or any other modification will weaken

the tank resulting in damage from rupture or explosion. Always replace worn, cracked or

damaged tanks.

Drain liquid from tank daily.

The tank should be carefully inspected at a minimum of once a year. Look for cracks forming near the welds. If a

crack is detected, remove pressure from tank immediately and replace.

Compressor Lubrication

See Installation. Add oil as required. The oil should be changed every three months or after every 200 hours of

operation; whichever comes first.

If the compressor is run under humid conditions for short periods of time, the humidity will condense in the

crankcase and cause the oil to look creamy. Oil contaminated by condensed water will not provide adequate

lubrication and must be changed immediately. Using contaminated oil will damage bearings, pistons, cylinders

and rings and is not covered under warranty. To avoid water condensation in the oil, periodically run the

compressor with tank pressure near 120 psi for single stage compressors by opening the drain cock or an air

valve connected to the tank or hose. Run the pump for an hour at a time at least once a week or more often if the

condensation reoccurs.

IMPORTANT: Change oil after first 50 hours of operation.

Air Filter

Never run the compressor pump without an intake air filter or with

a clogged intake air filter. The air filter element should be checked

monthly (see Figure 10). Operating compressor with a dirty filter can

cause high oil consumption and increase oil contamination in the

discharge air. If the air filter is dirty it must be replaced.

Figure 9 - ASME Safety Valve

Figure 10 - Air Filter Element

TROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

15

MAINTENANCE /

REPAIR

MAINTENANCE AND INSPECTION INSTRUCTIONS (CONTINUED)

Components

Turn off all power and clean the cylinder head, motor, fan blades, air lines, aftercooler and tank on a monthly

basis.

Belts

Lock out and tag the power then release all pressure from the tank to prevent unexpected

movement of the unit.

Check belt tension every 3 months. Adjust belt tension to allow 3/8 inch to 1/2 inch deflection with normal thumb

pressure. Also, align belts using a straight edge against the face of the flywheel and touching the rim on both

sides of the face. The belts should be parallel to this straight edge (see Figure 11). Dimension A should be the

same as B and C to ensure proper alignment of the belts.

Slots in the bed-plate allow for sliding the motor back and forth to adjust belt tension.

Storage

If compressor is to be stored for a short period of time, make sure that it is stored in a normal position and in a

cool protected area.

A B

C

Figure 11 - Top View

Air Compressor

Motor

Flywheel

Straight Edge

Motor Drive

Pulley

Setscrew

Maintenance Schedule

OPERATION DAILY MONTHLY 3 MONTHS

Check Safety Valve

l

Drain Tank (see Figure 8)

l

Check Oil Level

l

Clean or Change Air Filter

l

Check Intercooler

l

Clean Unit Components

l

Check Belt Tightness

l

Change Oil (see Figure 6)

l

For Repair Parts, visit www.jettools.com to find your local distributor

24 hours a day – 365 days a year

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown in parts list

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

16

REPAIR PARTS ILLUSTRATION FOR JCP-601

1

2

3

4

5

1

6

1

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25 26

27

28

29

30

31

32

33

34

35

36

33

MAINTENANCE /

REPAIRTROUBLESHOOTINGOPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

17

REPAIR PARTS LIST FOR JCP-601

Ref.

No. Description

Part

Number Qty.

1 3HP VT PUMP ASSEMBLY JCP601-001 1

2 3.2HP 240V ELECTRIC

MOTOR

JCP601-002 1

3 HEX HEAD SCREW, 5/16 IN.-

18 X 3/4 IN.

- 4

4 WASHER, 5/16 IN. - 4

5 SPINLOCK NUT, 5/16 IN.-18 - 4

6 SELF TAPPING SCREW,

5/16 IN.-12

- 4

7 WIRE BELT GUARD BACK JCP601-003 1

8 WIRE BELT GUARD FRONT JCP601-004 1

9 HEX FLANGE NUT 10-24 - 4

10 PULLEY 3.25 IN. X 5/8 IN.

BORE

JCP601-005 1

11 KEY, 3/16 IN. X 1 IN. JCP601-006 1

12 SET SCREW, 1/4 IN.-20 X

1/2 IN.

- 1

13 PIPE NIPPLE, 1/4 IN. NPT X

1.5 IN.

- 1

14 CHECK VALVE JCP601-007 1

15 QUICK CONNECT TUBE

FITTING, 1/4 IN. TUBE X

1/8 IN. NPT

JCP601-008 1

16 PLUG, 1/4 IN. NPT - 1

17 COMPRESSION NUT, 1/2 IN. JCP601-009 2

18 ASME SAFETY VALVE, 150PSI JCP601-010 1

19 GAUGE, 300PSI JCP601-011 1

20 COMPRESSION FITTING,

1/2 IN. NPT X 1/2 IN. TUBE

- 1

21 FERRULE, 1/2 IN. - 1

22 EXHAUST TUBE JCP601-012 1

23 TAPPING SCREW, 10-3/8 IN. - 1

24 MOLDED FERRULE, 1/2 IN. - 1

25 PRESSURE SWITCH WIRE

CLAMP

JCP601-013 1

26 CLAMP SCREW JCP601-014 1

27 HEX HEAD SELF TAPPING

SCREW, 8 - 3/8 IN.

- 2

Ref.

No. Description

Part

Number Qty.

28 BELT, AX48 VB-A48 1

29 PTFE TUBE, 1/4 IN. X 14 IN. - 1

30 BELT GUARD BRACKET JCP601-015 1

31 DRAINCOCK JCP601-016 1

32 PRESSURE SWITCH JCP601-017 1

33 TAPPING SCREW, 5-5/8 IN. - 5

34 MOTOR POWER CORD, 16 IN. JCP601-018 1

35 PLASTIC PLUG 3/4 IN. NPT - 1

36 60 GALLON ASME TANK JCP601-019 1

Not Shown:

37 GENERAL WARNING DECAL LM000184 1

38 JET LOGO 7-1/4 IN.H X

17 IN.W

LM000173 1

39 ID LABEL JCP-601 LM000174 1

6

4

9

3

1

10

13

7

12

15

11

16

14

2

5

8

17

18

19

20

8

For Repair Parts, visit www.jettools.com to find your local distributor

24 hours a day – 365 days a year

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as shown in parts list

REPAIR PARTS ILLUSTRATION FOR JCP-601

MAINTENANCE /

REPAIR TROUBLESHOOTING OPERATION

ASSEMBLY /

INSTALLATION

SAFETY /

SPECIFICATIONS GETTING STARTED

18

La page charge ...

JET 506601 Manuel utilisateur

JET 506601 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents