Paradigm PW 800 Le manuel du propriétaire

OWNER’S MANUAL

RECYCLING AND REUSE GUIDELINES FOR EUROPE

In accordance with the European Union WEEE

(Waste Electrical and Electronic Equipment)

directive effective August 13, 2005, we would like to

notify you that this product may contain regulated

materials which, upon disposal, according to the WEEE

directive, require special reuse and recycling processing.

For this reason Paradigm Electronics Inc. (manufacturers of

Paradigm speakers and Anthem Electronics) has arranged

with our distributors in European Union member nations to

collect and recycle this product at no cost to you. To find your

local distributor please contact the dealer from whom you

purchased this product or go to our website at paradigm.com.

Please note that the product only falls under the WEEE

directive. When disposing of packing and other shipping

material we encourage you to recycle through the

normal channels.

PW800: FCC ID: R48TT025 and IC ID: 7190A-TT025

PW 600: FCC ID: R48BS025 and IC ID: 7190A-BS025

PW AMP: FCC ID: R48MP025 and IC ID: 7190A-MP025

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) This device must accept

any interference received, including information that may cause

undesired operation. Changes or modifications not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This product has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This product generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television

reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician

for help.

This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

WIRELESS TRANSMITTER COMPLIANCE INFORMATION

The term “IC” before the radio certification number only

signifies that Industry Canada technical specifications were

met. This equipment complies with FCC and IC radiation

exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with

minimum distance 20 cm between the radiator and your

body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter. To reduce

potential radio interference to other users, the antenna

type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that

permitted for successful communication.

PARADIGM ELECTRONICS RESERVES THE RIGHT TO

CHANGE SPECIFICATIONS AND/OR FEATURES WITHOUT

NOTICE AS DESIGN IMPROVEMENTS ARE INCORPORATED.

PARADIGM and ANTHEM are registered trademarks of

Paradigm Electronics Inc. PW 800, PW 600, PW AMP, ARC

are trademarks of Paradigm Electronics Inc. Copyright

products and services mentioned may be trademarks or

service marks of their respective owner(s).

Apple and the Apple logo are trademarks of Apple Inc.,

registered in the U.S. and other countries. App Store is a

service mark of Apple Inc.

Windows

®

is a registered trademark of Microsoft Corporation in

the United States and other countries.

Amazon, Kindle, Fire, and all related logos are trademarks of

Amazon.com, Inc. or its affiliates.

Google Play is a trademark of Google Inc.

The Spotify software is subject to third party licenses found

here: www.spotify.com/connect/third-party-licenses

For DTS patents, see http://patents.dts.com. Manufactured

under license from DTS Licensing Limited. DTS, Play-Fi, the

Symbol, and Play-Fi together in combination with the Symbol

are trademarks of DTS, Inc. DTS and Play-Fi are registered

09.17.15 (REV. 002)

For more information visit paradigm.com

Congratulations! ....................................................1

Important Safety Instructions .........................................2

Important Safety Information .........................................3

What’s In The Box ...................................................4

PW 800 Premium Wireless Speaker ..................................4

PW 600 Premium Wireless Speaker ..................................5

PW AMP Premium Wireless Amplifier ................................6

Network Requirements .............................................. 7

System Requirements ............................................... 7

Features & Functions: ...............................................8

Controls & Connections .............................................. 9

PW 800 Premium Wireless Speaker ..................................9

PW 600 Premium Wireless Speaker .................................10

PW AMP Premium Wireless Amplifier ...............................11

Connecting PW AMP to Speakers .....................................12

Adding an Optional External Subwoofer ...............................13

Play Music & Connect Multiple PW Series Products .....................14

Anthem Room Correction (ARC

™

) .....................................15

Updates ...........................................................16

Reboot (Power Cycle) & Factory Reset ................................16

Enable/Disable Auto Input Mode .....................................16

Device Usage Guide .................................................17

Basic Troubleshooting ..............................................18

Technical Specifications .............................................21

PW 800 Premium Wireless Speaker .................................21

PW 600 Premium Wireless Speaker .................................22

PW AMP Premium Wireless Amplifier ...............................23

Limited Warranty ...................................................24

CONGRATULATIONS!

Thank you for purchasing this Paradigm

®

Premium Wireless

Series product.

Paradigm

®

and its sister company, Anthem

®

have leveraged over 30 years in

groundbreaking loudspeaker and amplifier design to create the Paradigm

®

Premium Wireless Series of wireless speakers and powerful amplifier.

The inclusion of DTS Play-Fi

®

technology to Paradigm’s technology platforms

means you can enjoy high fidelity, lossless music streamed from your Android

device, iOS device, tablet or PC – to a premium sounding Paradigm speaker, or

amplifier. Using your home Wi-Fi network, you can stream music to individual

speakers, or play the same music to all Paradigm

®

Premium Wireless Series

devices you have installed – all with crystal clear clarity.

1

Paradigm Premium Wireless Series Owner’s Manual

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

15. The apparatus shall not be exposed to dripping or splashing and

that objects filled with liquids, such as vases, shall not be placed

on apparatus.

16. The apparatus should be connected to a mains socket outlet with

a protective earthing connection.

2

IMPORTANT SAFETY INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE AND OBJECTS FILLED WITH

LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED

ON THIS APPARATUS.

• TO COMPLETELY DISCONNECT THIS APPARATUS

FROM THE AC MAINS, DISCONNECT THE POWER

SUPPLY CORD PLUG FROM THE AC RECEPTACLE.

• THE MAINS PLUG OF THE POWER SUPPLY CORD

SHALL REMAIN READILY ACCESSIBLE.

The lightning bolt flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING! Do not use your Paradigm product(s)

outside of the country of original sale—voltage

requirements vary by country. Improper voltage can

cause damage that will be potentially expensive to

repair. Paradigm products are shipped to authorized

Paradigm distributors with the correct power supply

for use in the country of intended sale. A list of

authorized distributors can be accessed at

www.paradigm.com or by emailing [email protected].

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING!

3

Paradigm Premium Wireless Series Owner’s Manual

2

5 6

3

4

1. Paradigm PW 800 Speaker

2. 6’ (1.8 m) Power Cable

3. 6’ (1.8 m) Ethernet Cable

4. ARC

™

Microphone

5. 6.5’ (2 m) ARC

™

Microphone USB Cable

6. Owner’s Manual and Setup Guide

1

4

PW 800 Premium Wireless Speaker

WHAT’S IN THE BOX …

1

4

PW 600 Premium Wireless Speaker

2

5 6

3

1. Paradigm PW 600 Speaker

2. 6’ (1.8 m) Power Cable

3. 6’ (1.8 m) Ethernet Cable

4. ARC

™

Microphone

5. 6.5’ (2 m) ARC

™

Microphone USB Cable

6. Owner’s Manual and Setup Guide

5

Paradigm Premium Wireless Series Owner’s Manual

6

WHAT’S IN THE BOX … (cont’d …)

1

4

2

5 6

3

PW AMP Premium Wireless Amplifier

1. Paradigm PW AMP

2. 6’ (1.8 m) Power Cable

3. 6’ (1.8 m) Ethernet Cable

4. ARC

™

Microphone

5. 6.5’ (2 m) ARC

™

Microphone USB Cable

6. Owner’s Manual and Setup Guide

7

Paradigm Premium Wireless Series Owner’s Manual

You must have the following to connect your Paradigm product to

your network:

• A high-speed DSL/Cable modem or a fiber-to-the-home

broadband connection for reliable playback of music services

based on the internet. Note: Satellite internet services are

prone to playback issues due to fluctuating download rates.

• If your modem is not a modem/router combination you must

purchase and install a router into your home network before

proceeding.

• If you plan to use the DTS Play-Fi

®

App on an Android

™

or

iOS device or you are setting up a Paradigm product for Wi-Fi

streaming, you will need a wireless router.

• Have your network password ready before connecting the

Paradigm product to your network.

NOTE: To make the quickest connection, use a dual-band router

and connect your Paradigm Product to the 5G network instead of

the 2.4 Network.

NOTE: If your wireless connectivity is weak or not available,

connect your Paradigm product to your router with the supplied

ethernet cable.

TIP! Paradigm Premium Wireless Series products communicate

with wireless networks that support 802.11 g/n wireless

technology. For the fastest streaming performance, a network

that supports 802.11 n wireless technology is recommended. A

network supporting 802.11b may be used, but it will effectively

stream to only one device equipped with DTS Play-Fi

®

.

TIP! For superior performance connect your PC or NAS (Network-

Attached Storage) drive that holds your personal music library to

your network router using the provided Ethernet cable.

NETWORK REQUIREMENTS

SYSTEM REQUIREMENTS

• An Android device running Android 2.2 or later.

• An iOS device running iOS 6.0 or later.

• A Windows

®

PC running Windows

®

7, 8 or 8.1 (32 and 64 bit).

FEATURES & FUNCTIONS

Power Button ( ):

• Press

to power on/off. If no signal is

received for 20 minutes, unit will be in

standby.

• Press

to reboot (power cycle) or

Factory Reset your Paradigm product

(see page 16).

Volume Up/Down Buttons (

/ ):

• Press

to increase the volume level.

Press

to decrease the volume level.

• Press and hold either

/ to ramp the

volume level up or down.

Mute Button (

):

• Press

to mute the audio. The Mute

button (

) will illuminate WHITE when

the mute function is active.

• The Mute Button (

) also switches on/

off ARC

™

Settings

– To setup ARC

™

and to learn how it

corrects room deficiencies see page

15.

– To switch off ARC

™

settings: PRESS

and HOLD

for 5 seconds. Upon

releasing the button, a “negative tone”

will sound verifying ARC

™

settings are

switched off.

– Repeat the process to switch on ARC

™

settings. You will hear a “positive tone”

when ARC

™

settings are switched on.

Input Button (

):

• PRESS and RELEASE

to toggle

between Wireless/Wired Network

Streaming Mode AND Rear Input Mode.

• The Input button (

) illuminates WHITE

when Wireless/Wired Network Streaming

Mode is enabled and BLUE when the

Rear Input Mode is enabled.

• Your Paradigm product has the following

rear input: 3.5 mm Analog Input (PW 800

and PW 600) OR RCA Analog Input (PW

AMP).

• Wireless/Wired Network Streaming

Mode is the default input mode. If your

Paradigm product is set to Rear Input

Mode and music is streamed, by default

your Paradigm product will switch to

Wireless/Wired Network Streaming

Mode.

• Enable/disable Auto input Mode

(see page 16).

Wi-Fi Setup Button:

• Initiates Wi-Fi setup for both Wi-Fi

Protected Setup (WPS)

and Standard Wi-Fi Setup.

Stereo/Mono Setting Switch (L/S/R)

(PW 600 ONLY):

• For stereo output from one PW 600

speaker, set the switch to the “S”

(Stereo) position. For a stereo pair, set

the switch to either “L” (Left) or “R”

(Right) depending on the position of your

speaker within a listening space. For

example: If your speaker is in the left

position within a listening space, set the

switch to the “L” (Left) position. Follow

app instructions for pairing with iOS/

Android apps.

Wi-Fi Indicator (

):

The Wi-Fi Indicator (

) tells you what your

Paradigm product is doing:

• Fast Blinking – Your Paradigm

product is booting up.

• Blinking – Your Paradigm product is

attempting to connect to a wireless

router.

• Slow Pulse – Setup Mode.

• Two Blinks > Pause – WPS Mode.

• Solid – Connected to router.

• Off – Connected to a router

using a wired connection.

8

9

Paradigm Premium Wireless Series Owner’s Manual

CONTROLS & CONNECTIONS

PW 800 Premium Wireless Speaker

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Power

Wi-Fi Indicator

AC Power

(Mains)

Input

3.5 mm

Analog

Input

Volume Up

Volume Down

Mute

Input

Subwoofer

Output

(optional)

Mini USB

(factory

use only)

Wi-Fi

Setup

Button

Ethernet

Input

USB

(factory

use only)

10

CONTROLS & CONNECTIONS (cont’d …)

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

PW 600 Premium Wireless Speaker

Power

Wi-Fi Indicator

Volume Up

Volume Down

Mute

Input

AC Power

(Mains)

Input

3.5 mm

Analog

Input

Ethernet

Input

Subwoofer

Output

(optional)

Mini USB

(factory

use only)

Stereo/

Mono

Setting

*

For one PW-600 speaker set to Stereo (S) and

for two PW-600 speakers set to Left (L) or Right (R).

USB

(factory

use only)

Wi-Fi

Setup

Button

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

11

Paradigm Premium Wireless Series Owner’s Manual

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

120V 2A 60Hz

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

Analog In

UpdateL S R

Sub Out

Wi-Fi

Setup

USB

LAN

PW 600

120V 2A 60Hz

Analog In

Right Left

Update

USB

LAN

Wi-Fi

Setup

R

L

Sub Out

+

-

+

-

PF AMP

120V 2A 60Hz

PW AMP

PW 600

PW 800

Analog In

Update

Sub Out

Wi-Fi

Setup

USB

LAN

120V 2A 60Hz

PW 800

Class 2

Wiring

PW AMP Premium Wireless Amplifier

Volume

Down

MuteInput Volume

Up

Power

AC Power

(Mains) Input

Wi-Fi Setup

Button

Mini USB

(factory

use only)

Ethernet

Input

USB

(factory

use only)

RCA Analog

Input

Subwoofer

Output

(optional)

Right Speaker

Terminals

Left Speaker

Terminals

Wi-Fi Indicator

WARNING: Use Class 2 wiring only.

CAUTION: Do not connect speakers, which are rated

less than 4 Ohms to the Paradigm PW AMP.

CAUTION: While making connections with bare

wire, ensure that none of your bare wire comes in

contact with a an adjacent terminal.

The speakers to be connected to the Paradigm PW AMP should

be rated to handle at least 75 W for 8 Ohm speakers and at least

150 W for 4 Ohm speakers.

Your PW AMP’s binding posts can be used with banana, plug

connectors, and bare wire.

IMPORTANT! Correct polarity (or phase) is critical for proper

soundstage imaging and bass performance. Connect one

speaker at a time to ensure proper connection of every channel.

The red (+) amplifier terminal must be connected to the red (+)

speaker terminal. The same applies to the black (–) terminals.

Make sure all wires are firmly fastened. Repeat this connection

procedure for each speaker in your system.

IMPORTANT! If you hear a distinct lack of bass and a dislocated

stereo image then one or more of your speakers may be connected

out of phase (polarity is reversed). Re-check to ensure that each

speaker’s cable is connected with correct polarity: red (+) to red (+)

and black (–) to black (–).

Bare Wire Connectors:

If you are using speaker wire without banana plugs, simply press in the

spring loaded binding post to expose the connection hole. Insert the stripped

end of the speaker wire into the hole, then release the binding post. The

exposed speaker wire should be securely gripped by the binding post.

Banana Plug Connectors:

If you are using banana plugs, remove the end caps from the

PW AMP’s binding posts to expose the banana plug socket;

insert the banana plug into the socket.

12

CONNECTING PW AMP TO SPEAKERS

13

Paradigm Premium Wireless Series Owner’s Manual

ADDING AN OPTIONAL EXTERNAL SUBWOOFER

If desired, an external subwoofer can be used to reinforce

low-frequency channel information in multichannel and stereo

recordings. For seamless system matching, we recommend

a Paradigm subwoofer, however any brand of subwoofer can

be connected.

Using a high-quality RCA style cable, connect the “Sub Out” on

the Paradigm Premium Wireless Series product back panel to the

“LFE In/Sub In” on the subwoofer’s back panel.

TIP! Reference your subwoofer’s Owner’s Manual to learn how

to properly adjust the subwoofer’s level and phase controls to

achieve proper blending with the PW AMP.

Upon connecting an external subwoofer, your Paradigm product

will automatically detect its presence and redirect low frequency

content from the speakers to the subwoofer. If your subwoofer has

an adjustment for bandwidth (BW), set it to 100 Hz (recommended

setting) if you will not be running ARC. If you will be running ARC

set it to maximum bandwidth (or bypass). If you ran ARC before

connecting a subwoofer, you will need to run it again.

PLAY MUSIC & CONNECT MULTIPLE PW SERIES PRODUCTS

Once your Paradigm product is connected to your home network,

you can start playing music anytime.

1. Activate the DTS Play-Fi

®

App on your mobile device or PC. If

you have setup more than one Paradigm product, select which

one you want to stream music to.

2. Select your music source – personal music library or any

subscription-based music service contained on your mobile

device or PC, Internet Radio, or from select online music

services such as Deezer, Songza, etc. (visit our website at

paradigm.com to view a full list of available music services).

How to Connect Multiple Paradigm Premium Wireless

Series products:

1. To connect additional Paradigm Premium Wireless Series

products to your network, open the DTS Play-Fi

®

App and

select “Setting”.

2. Select, “Add Play-Fi Device”

3. Follow the instructions to add each Paradigm Premium

Wireless Series product.

Primary/Secondary Zones:

When using the DTS Play-Fi

®

App on your device, you will notice

when streaming music to your Paradigm Premium Wireless Series

product that there are two groups: Primary and secondary zones.

The DTS Play-Fi

®

module within your Paradigm Premium Wireless

Series product requires that a primary speaker be selected to create

a new listening session or zone. The purpose of this is to eliminate any

echo, found on other ecosystems, and to maximize synchronization

down to 1 millisecond.

We suggest that you select the Paradigm Premium Wireless Series

product with the strongest signal strength as your primary device.

It should be noted that secondary speakers are connected to your

primary speaker, so if you disable your primary speaker for any

reason, your secondary speaker will be temporarily unavailable

until a primary speaker is selected again.

14

Even when the finest speakers are perfectly positioned, the room

itself still has a dramatic impact on any system’s sound, an impact

more profound than that of any individual component. Various

solutions have fallen in and out of favor over the years, but none

has solved the problem of “the room.” Until ARC.

Using proprietary processes and the power of your PC, the ARC

system analyzes each speaker’s in-room sound, then computes the

required correction to yield optimal performance from every speaker.

It’s a process that takes approximately 15 minutes. Anthem’s

approach is a true audiophile solution to the problems of the room.

IMPORTANT! The listening space must be silent while performing

ARC. A noisy computer fan, a dishwasher or microwave running,

etc. can negatively affect ARC’s measurements.

How to Correct Room Deficiencies using ARC Technology :

1. Ensure that your Paradigm product is already connected on

your home network and is powered “on”.

2. Download the ARC software from paradigm.com/support and install

it. Once the drivers are installed, follow the on-screen instructions.

3. Using the 6.5’ (2 m) USB cable, connect the ARC microphone to a

Windows

®

PC running Windows

®

7 or 8 (32 and 64 bit).

4. Look for the icon on your desktop and launch the ARC

™

program. Follow

the prompts on your computer screen to successfully run the ARC

™

software; the entire process should take approximately 15 minutes.

5. Hold the ARC microphone with your arm fully extended, the ARC

microphone tip must point towards the ceiling and it must be

positioned at ear level. Refer to the diagram below.

6. For best results, hold the microphone in 5 different positions

around the room.

TIP! Once the ARC process is complete, the corrected listening

curves will be stored and music will be played back reflecting these

corrections each time you stream music to your Paradigm product.

To toggle back and forth between pre and post ARC correction, or

to disable ARC refer to the “Mute Button ( )” section on page 8.

ANTHEM ROOM CORRECTION (ARC

™

)

E

a

r L

e

v

el

ARC

Microphone

Paradigm Premium Wireless Series Owner’s Manual

15

UPDATES

REBOOT (POWER CYCLE) &

FACTORY RESET

ENABLE/DISABLE AUTO

INPUT MODE

DTS Play-Fi

®

App Update:

If the DTS Play-Fi

®

app on your device requires an update, the app

will notify you that an update is available and guide you through

the update process.

Paradigm Firmware Update:

At Paradigm we constantly strive to improve the performance and

functionality of your system, as a result from time to time your

Paradigm Premium Wirless Series product will require firmware

updates. Please regularly check our website at www.paradigm.com

for the latest firmware updates.

Reboot (Power Cycle):

PRESS and HOLD the Power button (

) for 3 seconds. The Mute

button ( ) will start blinking once a refresh has been achieved;

upon releasing the button a tone will verify a refresh.

Factory Reset:

PRESS and HOLD the Power button ( ) for 10 seconds (at 3 seconds

the Mute button ( ) will start blinking); once you hear a tone (at 10

seconds) to verify a reset, immediately release the reset button.

Paradigm PW products can be configured to automatically select

the AUX input when the Play-Fi app is turned off. This mode can

be useful when using the PW product to improve TV audio, for

example, through the AUX input when wireless music streaming

is not in use. To enable auto input mode, hold the input button for

five seconds. Hold it again for five seconds again to cancel.

16

Paradigm Premium Wireless Series Owner’s Manual

PW 800

• Select music services

• iTunes – music stored on device

• Select music services

• Music stored on device

• All audio content

Apple iOS

Play-Fi

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

• Up to eight

• Multiple simultaneous users

• Speakers can be zoned

ContentDevice

App

Multi-Room

Android

Windows PC

Play-Fi

DEVICE USAGE GUIDE

17

BASIC TROUBLESHOOTING

18

CAUTION: Warning: Do not open the product.

Under no circumstances should the product be

repaired by anyone other than an authorized

Paradigm Dealer, as this will invalidate the

warranty. Please contact Paradigm Customer

Support for more information.

If a problem occurs, you can try the troubleshooting suggestions

listed below. If one of these doesn’t remedy the problem, or

you are not sure how to proceed, please contact the Paradigm

Customer Support team at support@paradigm.com. Alternatively,

visit our website at paradigm.com/support for detailed

troubleshooting solutions.

I am unable to connect

the Paradigm Premium

Wireless Series product

to my Wi-Fi network.

1. Verify that your Wi-Fi network is functioning.

2. Your router’s Wi-Fi signal may be weak or your Paradigm product may be out of range of your

router’s Wi-Fi network. Move the Paradigm product closer to the router.

3. Before connecting to your network, verify that your Paradigm product’s Input button ( ) is illuminated in

WHITE, this indicates the Wireless/Wired Network Streaming Mode. If the Input button ( ) is illuminated

in BLUE, this indicates the Rear Input Mode; press the Input button ( ) to select the Wireless/Wired

Network Streaming Mode for a wireless input connection.

4. Reboot your Paradigm product (see page 16).

5. Reset your Paradigm product to factory settings (see page 16).

Problem Possible Solutions

La page charge ...

Paradigm PW 800 Le manuel du propriétaire

Ce manuel convient également à

Paradigm PW 800 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents