Tripp Lite SmartOnline 208V SV-Series 3-Phase Modular UPS Systems Le manuel du propriétaire

1

Owner’s Manual

SmartOnline

®

208V SV-Series

3-Phase Modular UPS Systems

(Series Number: AG-0172) (Series Number: AG-0173) (Series Number: AG-0174)

Input: 120/127V (Ph-N), 208/220V (Ph-Ph)

(Not suitable for mobile applications)

Español 39 • Français 77

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

2

Table Of Contents

1. Introduction 3

2. IMPORTANT SAFETY WARNINGS 4

2.1 Location Warning 4

2.2 EMC 4

2.3 Connection Warning 4

2.4 Battery Warning 5

2.5 Safety Standards 5

3. UPS Layout 6

3.1 SmartOnline SV-Series Layout 6

3.2 Package Contents 8

4. Positioning and Pre-Installation 9

4.1 Important Safety Warning 9

4.2 Transportation 9

4.3 Delivery 9

4.4 Installation Environment 9

4.5 Unpacking the UPS 10

5. Wiring and Block Diagrams 11

5.1 Block Diagram 11

5.2 Function of Core System Elements 11

6. Operating Overview 12

6.1 Operating Modes 12

6.2 Single or Dual Feed Input 12

7. Installation 13

7.1 Breakers and Wiring Terminal Block 13

7.2 STS Module Installation 13

7.2.1 Installing a Power Module 15

7.2.2 Removing a Power Module 16

7.2.3 Installing a Battery Module 16

7.2.4 Removing a Battery Module 16

7.2.5 External Battery Cabinet Connection 17

7.3 Cold Start 17

7.4 Conduit Box Installation 18

(for Small Frame Models)

8. Manual Maintenance Bypass 19

8.1 Transfer to Bypass via STS Module Connector 19

from UPS Mode

8.2 Transfer to Bypass via Control Panel 19

9. Control Panel 20

9.1 Introduction 20

9.2 Audible Alarms 21

9.3 Screen Descriptions 21

9.3.1 Start-Up Screen 21

9.3.2 Home Screen 21

9.3.3 Menu Screen 21

9.3.4 Control Screen 22

9.3.5 Measurement Screen 23

9.3.6 Setup Screen 24

9.3.6.1 General 24

9.3.6.2 System 25

9.3.6.3 Battery 26

9.3.6.4 Pre-Alarm 27

9.3.7 Information Screen 27

9.3.8 Events Screen 28

9.3.8.1 Current Events 28

9.3.8.2 Historical Events 29

9.3.8.3 Reset All Events 29

9.4 Text Summaries and Explanations 29

10. Communication 31

10.1 STS Module 31

10.2 Dry Contact Ports 31

10.2.1 Remote EPO Input Port 31

10.2.2 Maintenance Bypass Switch Port 32

10.3 Connectivity 32

10.3.1 SNMP 32

10.3.2 Serial Port 32

10.3.3 USB Port 32

11. Maintenance 33

11.1 Power Module Replacement 33

11.2 Battery Module Replacement 33

11.3 Installing/Replacing the Air Filters 33

12. Troubleshooting 34

13. Technical Speciﬁcations 35

14. UPS and Battery Storage; Battery Disposal 37

14.1 UPS and Battery Storage 37

14.2 Battery Disposal 37

15. Warranty and Product Registration 38

3

1. Introduction

Tripp Lite’s SmartOnline SV-Series Uninterruptible Power Supply (UPS) is a Voltage and Frequency Independent (VFI) true on-line, double

conversion 3-Phase UPS system. This UPS continuously conditions the incoming electrical power supply, eliminating power ﬂuctuations and

interruptions that can otherwise damage sensitive electronic devices and create system downtime. Ranging from 20kVA/18kW to 140kVA/126kW,

this series of UPS systems is designed to the highest quality and performance standards and offers the following features:

• True on-line UPS: highest level of UPS protection, fully regulating the incoming power supply and transferring immediately to battery in the

event of an extended mains failure for continuous support of critical loads

• Modular system: three frame arrangements with multiple construction possibilities to suit speciﬁc application requirements; easy and fast

maintenance with hot-swappable power and battery modules

• N+1 redundancy up to 140kVA

• High efﬁciency – lower heat losses reduce cooling costs and extend system lifespan

• 0.9 output power factor – more actual power allows more equipment to be supported

• Automatic and manual bypass increase system reliability and allow for maintenance without removing power from the attached load

• Wide input voltage window – the UPS system regulates even poor-quality incoming power without reverting to battery, maximizing system

uptime and protecting battery life

• Compact form factor; space-saving design even up to 140kVA in a standard rack footprint

• Serial communication as standard; SNMP and volt free contact options for optimum conﬁgurability

• Dual input design allows standard installation from one or two power sources

• Low input current total harmonic distortion; no need to oversize a generator set

The SmartOnline SV UPS is designed for protecting critical electrical equipment for:

• Data centers

• Telecommunications

• Networks (LAN/WAN)

• Corporate infrastructure

• Healthcare

• Security

• Light industrial

• Financial institutions

4

2. IMPORTANT SAFETY WARNINGS

SAVE THESE INSTRUCTIONS.

This manual contains important instructions and warnings that should be followed during the installation,

operation and maintenance of all Tripp Lite SmartOnline SV 3-phase UPS systems and batteries. Read all

instructions thoroughly before attempting to move, install or operate the UPS. Failure to comply may invalidate

the warranty and cause property damage and/or personal injury.

2.1 Location Warning

This UPS contains LETHAL VOLTAGES. All repairs, service and installation must be performed by AUTHORIZED SERVICE PERSONNEL ONLY.

There are NO USER SERVICEABLE PARTS inside the UPS.

• SmartOnline SV UPS systems are designed for commercial and industrial application purposes only.

• Cabinets must be installed on a level ﬂoor suitable for computer or electronic equipment.

• The UPS cabinet is heavy. Closely follow unloading instructions to avoid the risk of injury.

• Install the UPS system in a controlled indoor environment, away from moisture, temperature extremes, ﬂammable liquids and gasses,

conductive contaminants, dust and direct sunlight. The system is not intended for outdoor use.

• Operate the UPS at indoor temperatures between 32° to 104°F (0° to 40°C) only. For best results, maintain indoor temperature between

63° to 77°F (17° to 25°C).

• Do not place any object on the UPS system, especially containers of liquid.

• Do not install the UPS with the front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the unit’s internal

cooling, causing product damage not covered under warranty.

• Do not tilt the UPS cabinet more than 10°.

• Do not attempt to unpack or move the UPS without assistance.

2.2 EMC

WARNING:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his own expense. Changes or modiﬁcations not expressly approved by

the party responsible for compliance could void the user’s authority to operate the equipment.

2.3 Connection Warning

BEFORE WORKING ON THIS UPS

• Isolate the SmartOnline SV UPS.

• Check for hazardous voltages between all terminals, including the protective earth.

• Risk of Voltage Backfeed: The isolation device must be able to carry the UPS input current. The backfeed protection device should be

VDE/EN/UL approved and rated 220V (L-N) / 380V (L-L), 630A (Large Frame) / 300A (Medium Frame) / 250A (Small Frame).

Figure 2.1: Backfeed Protection Connections

5

2. IMPORTANT SAFETY WARNINGS

START-UP AND COMMISSIONING

An authorized Tripp Lite engineer must perform the start-up of the UPS and a completed start-up form must be returned to

Tripp Lite in order to activate the SmartOnline SV warranty. Please contact your local supplier or [email protected]

for further details. To ﬁnd your local contact, go to www.tripplite.com/support/contacts.

This UPS contains LETHAL VOLTAGES. KEEP DOORS LOCKED AT ALL TIMES. All repairs, service and installation must be performed by

AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.

• Ensure all power is disconnected before performing installation or service.

• The UPS system contains its own energy source (battery). The output terminals may carry live voltage even when the UPS is disconnected from

an AC source.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life

support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

• The Protective Earth Ground must be installed ﬁrst prior to any power connections made to the equipment.

• Installation and wiring must be performed in accordance with local electrical laws and regulations.

• The AC disconnection device must break line and neutral conductors: four connectors for three phases (L1, L2, L3 and N).

• The DC disconnection device must break line with both the positive and negative conductors.

• A readily accessible, external disconnect device to the equipment shall be provided for the AC and DC supplies in the end installation.

2.4 Battery Warning

This UPS contains LETHAL VOLTAGES. The UPS is designed to supply power even when disconnected from utility power. Only AUTHORIZED

SERVICE PERSONNEL should access the interior of the UPS, after disconnecting the utility and DC power.

Batteries present a risk of electrical shock and burns from high short-circuit current. Battery connection or replacement should be performed

only by qualiﬁed service personnel, observing proper precautions. Turn off the UPS before connecting or disconnecting internal batteries. Use

tools with insulated handles. Do not open the batteries. Do not short or bridge the battery terminals with any object.

• The batteries are recyclable. Refer to local codes for disposal requirements or visit http://www.tripplite.com/support/recycling-program for

recycling information.

• Do not dispose of the batteries in a ﬁre, mutilate the batteries or open the battery coverings. Escaping electrolytes may be toxic and cause

injury to skin and eyes.

• Do not disconnect the batteries while the UPS is in battery mode.

• Disconnect the charging source prior to connecting or disconnecting terminals.

• The following precautions should be observed:

1. Remove watches, rings and other metal objects.

2. Use tools with insulated handles.

3. Wear rubber gloves and boots.

4. Do not lay tools or metal parts on top of batteries or battery cabinets.

5. Determine whether the battery is inadvertently grounded. If it is, remove the source of the ground. Contact with any part of a grounded

battery can result in electric shock. The likelihood of an electric shock is reduced if such grounds are removed during installation and

maintenance.

• Battery replacement should be performed only by authorized service personnel, using the same number and type of batteries

(sealed lead acid).

• If the UPS system remains off for an extended period of time, it should be turned on periodically and the batteries should be fully charged.

See Section 14.1 UPS and Battery Storage for battery storage recommendations. Failure to recharge the batteries may cause irreversible

battery damage.

2.5 Safety Standards

Item Normative reference

Uninterruptible power systems (UPS) UL 1778, CSA C22.2 No.107.3-14

Notes:

Conducted FCC Part 15, Subpart B Class A

Radiated FCC Part 15, Subpart B Class A

6

3. UPS Layout

3.1 SmartOnline SV-Series Layout

30U FRONT VIEW

(Small Frame)

23.64 in. (600 mm)

79 in. (2010 mm)

42U FRONT VIEW

(Medium/Large Frame)

23.64 in. (600 mm)

34.65 in. (880 mm)

66 in. (1680 mm)

45.28 in. (1150 mm)

43.30 in. (1100 mm)

58 in. (1475 mm)

Figure 3.1: Dimensions

Frame Selection Height Width Depth

Small Frame (30U) 20-60kW with integrated batteries 58 in. (1475 mm) 23.64 in. (600 mm) 43.30 in. (1100 mm)

Medium Frame (42U) 20-80kW with integrated batteries 79 in. (2010 mm) 23.64 in. (600 mm) 43.30 in. (1100 mm)

Large Frame (42U) 20-140kW without battery 79 in. (2010 mm) 23.64 in. (600 mm) 43.30 in. (1100 mm)

7

3. UPS Layout

1

LED and LCD Control Panel

2

Front Door Lock

3

Switch Module

4

Input Breaker

5

Maintenance Bypass Breaker

6

Output Breaker

7

STS Module

8

Power Module/s

9

Battery Module/s (small and medium frame models; see Section 13. Technical Speciﬁcations for a full listing)

10

Leveling Feet

11

Casters

12

Rear Door Lock

13

Battery Breaker (small and medium frame models; see Section 13. Technical Speciﬁcations for a full listing)

14

Input/Output Terminal Conduit Cover

1

3

7

8

9

10

12

13

1110 10 10

11

4

14

5 6

2

8

3. UPS Layout

3.1 SmartOnline SV-Series Layout

The modularity of the SmartOnline SV-Series allows three frame arrangements with multiple construction possibilities according to the user’s

power rating and battery runtime requirements. The table below indicates the module capacity per frame. Refer to Section 13 Technical

Speciﬁcations for detailed breakdown of maximum Power and Battery Modules per frame.

Small Frame Medium Frame Large Frame

Models with

Batteries

Models without

Batteries

Models with

Batteries

Models without

Batteries

Models without

Batteries

Cabinet Height

30U 30U 42U 42U 42U

Switch Module (built into frame)

1 1 1 1 1

STS Module (built into frame)

1 1 1 1 1

Max. Power Module

3 3 4 4 7+1

1

Max. Battery Module

3 0

2

4 0

2

N/A

2

Note: Consider the wiring gauges and external battery space requirements for the large frame. Each battery module is comprised of four trays of batteries. Each

tray contains 10 pieces 12V/9Ah battery. Four trays must be utilized per module; it is not possible to install partial modules.

1

The large frame hosts up to 140kVA/126kW power capacity without battery modules. An additional power module for large frame models may be added for N+1

redundancy.

2

Battery modules are available in small and medium frames only. Large frame models do not contain battery modules.

3.2 Package Contents

Tripp Lite SmartOnline SV UPS * (1)

Owner’s Manual (1)

M4 Screws (40) **

Washers (40) **

M4 Screws (24) ***

Washers (24) ***

Frame Door Keys (4)

Serial Cable (1)

* The Switch/STS module is delivered with the frame; the power module, battery modules and WEBCARDLX are packaged separately.

** Medium frame

*** Small frame

9

4.1 Important Safety Warning

Read this manual thoroughly before undertaking any installation and wiring. An authorized Tripp Lite engineer must perform the start-up of the

UPS and a completed start-up form must be returned to Tripp Lite in order to activate the SmartOnline SV warranty. Contact Tripp Lite at www.

tripplite.com/support/contacts for further details.

4.2 Transportation

WARNING

The UPS is packed on a pallet suitable for handling with a forklift. If using a forklift or other equipment to move the UPS, ensure

its load bearing capacity is sufﬁcient to support the total packing weight of the UPS.

The UPS is ﬁxed on the pallet with four balance supports. When removing them, pay attention to the movement of the casters to

avoid accidents.

The UPS cabinet may be pushed forward or backwards only; it may not be moved sideways. The cabinet has a high center of

gravity; take care to not tip or overturn the cabinet during transportation.

If moving the UPS over long distance, use appropriate equipment such as a forklift. Do not move the UPS cabinet using its

attached casters over long distances. Move the UPS cabinet in its original packaging until at the ﬁnal destination site.

4.3 Delivery

Inspect the packaging materials and UPS cabinet carefully upon delivery. Do not install a damaged UPS, connect it to a battery or to the utility.

The packing box of the UPS is equipped with an anti-tilt device. Conﬁrm the device does not indicate any shock or excess tilt during transit. If the

device indicates there has been excessive shock or tilt, do not install and contact your local Tripp Lite representative.

4.4 Installation Environment

• The UPS is designed for indoor use only. Do not place or install the UPS in an outdoor area.

• When moving the UPS to its installation site, ensure all corridors, doors, gates, elevators, ﬂoors, etc. are able to accommodate and bear the

combined weight of the UPS system, any associated battery cabinets and all handling equipment. See Section 13. Technical Speciﬁcations

for UPS module combined weights.

• The installation site should have a dedicated AC circuit available, compatible with the UPS system’s input requirements. See Section 13.

Technical Speciﬁcations for input speciﬁcations.

• Ensure the installation area has sufﬁcient space for maintenance and ventilation of the UPS system.

• Maintain the installation area’s temperature below 86°F (30°C) and the humidity below 90%. The highest operating altitude is 6500 ft.

(2000 m) above sea level. Please consider the derating values when operating the UPS over 3280 ft. (1000 m). The optimum operating

temperature for the batteries is 77°F (25°C).

• The UPS should be located in an environment with clean air and adequate ventilation to maintain the ambient temperature within the UPS

operating range.

• The UPS is air-cooled with the aid of internal fans. Do not cover the ventilation openings of the UPS system.

• Install the UPS in an area in which the walls, ﬂoors and ceilings are constructed with ﬁreproof materials. The UPS is suitable for mounting on

concrete or other non-combustible surfaces only.

• Install a CO

2

or dry powder extinguisher in the installation area.

• Maintain a clearance of at least 48 in. (120 cm) from the top of the UPS for maintenance, cabling and ventilation.

• Maintain a clearance of at least 40 in. (100 cm) from the rear and front of the UPS for access and ventilation.

4. Positioning and Pre-Installation

10

4. Positioning and Pre-Installation

4.5 Unpacking the UPS

1. Once the UPS system has arrived at the installation site, it may be removed from the packing box. Follow the unpacking procedure below to

remove main carton (Figure 4.1) and protective materials (Figure 4.2).

Figure 4.1

Figure 4.2

2. Place the ramp delivered in the packing box in front of the UPS cabinet and align the hole in the ramp to the metal stud on the pallet and lock

into place (Figure 4.3).

3. Remove the four ﬁxing plates (Figure 4.4) and loosen the leveling feet by rotating them counterclockwise, raising them above the level of the

casters. The UPS cabinet may now be rolled off the pallet and down the ramp. At least three people should be present to move the UPS to

the installation area, two to support either side of the UPS and a third to guide the UPS into its ﬁnal location.

4. The casters are designed to move on a level surface over a short distance for ﬁnal UPS placement. Do not move the UPS using the casters

over long distances or across uneven surfaces. This could damage the casters and/or tip the UPS.

5. Once the UPS is in ﬁnal position, rotate the leveling feet clockwise below the level of the casters to secure in place (Figure 4.5). Do not rest

the UPS permanently on the casters.

Figure 4.3

Figure 4.4

Figure 4.5

11

5. Wiring and Block Diagrams

5.1 Block Diagram

Without

Jumpers

Figure 5.1: Wiring diagram for dual inputs

Figure 5.2: Wiring diagram for single input

5.2 Functions of Core System Elements

Rectiﬁer: Converts AC from the utility into DC voltage and charges the battery.

Inverter: Converts DC voltage into fully regulated, clean AC voltage to power the attached load. Regardless of the AC waveform from the utility,

the load receives a clean, consistent sine wave with stable voltage and frequency.

Automatic Bypass (Static Switch): Transfers the attached load to mains in case of overload or internal failure. The load is kept powered up as

long as the mains power is available.

Manual Bypass (Maintenance Breaker): User-operated physical switch. The user can transfer the load to bypass to perform UPS maintenance

without powering down the load.

12

Small- and Medium-Frame Units

INPUT 1

INPUT 2

Figure 6.3

For dual input installation, red, yellow and black wire jumpers must be

removed as shown in Figure 6.3 (top rear view of cabinet).

Large-Frame Units

INPUT 1 BUSBAR

INPUT 2

Figure 6.4

For dual input installation, busbar jumpers must be removed as shown

in Figure 6.4 (top view of cabinet).

6. Operating Overview

6.1 Operating Modes

Normal (Double Conversion, VFI)

Power ﬂows through the UPS rectiﬁer and inverter. Voltage and

frequency to the load is independent of voltage and frequency from the

input. There are higher efﬁciency losses in this mode due to the double

conversion process.

Q

2

Maintenance Breaker

Q

1

Input Breaker

Q

3

Output Breaker

Inverter

Relay

Battery Breaker

Rectifier Inverter

STS

Bypass

Main Load

ECO Mode

When utility power quality is stable, power can be diverted through the

automatic bypass of the UPS. If the utility power goes out of tolerance

or is lost, the UPS transfers quickly back to inverter to power the load

in VFI mode. The result is improved efﬁciency and cost savings when

power conditions are good.

Q

2

Maintenance Breaker

Q

1

Input Breaker

Q

3

Output Breaker

Inverter

Relay

Battery Breaker

Rectifier Inverter

STS

Bypass

Main Load

6.2 Single or Dual Feed Input

The UPS can accept dual inputs for additional redundancy (e.g. in a server rack installation operating on dual AC feeds).

When powering the UPS with dual AC feeds, ﬁrst remove the jumpers, as shown below.

Figure 6.1 Figure 6.2

13

7. Installation

7.1 Breakers and Wiring Terminal Block

The input breaker, maintenance bypass breaker and output breaker are located at the front of the Switch Module of the UPS system. The battery

breaker and input/output wiring terminal blocks are at the rear of the Switch Module. To access the terminals from the back of the UPS, remove

the protective Plexiglas

®

panel cover. Wiring installation must be made from the top of the UPS cabinet using the two terminal conduit covers

provided. For connection details, refer to Figure 7.1 (large-frame terminal block shown).

Figure 7.1

Function Description

Output Block Connection to the supported load Includes R (L1), S (L2), T (L3) and Neutral terminals

Alternate Input Block (Input 2) Alternate AC input source connection Includes R (L1), S (L2), T (L3) and Neutral terminals

Main Input Block (Input 1) Primary AC input source connection Includes R (L1), S (L2), T (L3) and Neutral terminals

Grounding Terminal For UPS grounding Includes one grounding terminal

Battery Input Block For external battery connection Includes Positive (+), Negative (-) and Neutral (N) terminals

7.2 STS Module Installation

The STS Module and Switch Module are pre-installed in the frame. STS Module comprises:

• Control Circuit

• Power Circuit

• Communication Circuit (including SNMP, Serial [RS-232])

• Internal Static Transfer Switch

• Breaker(s)

Power and Battery Modules can be added according to the user’s requirements. The tables on the following page indicate the maximum current

and cable conﬁgurations per assembly.

Note: Internal battery modules for Small- and Medium-Frame systems only.

14

7. Installation

AC Input and Output Maximum Current & Power Cable Conﬁguration

Note: Use copper wire with minimum temperature rating of 221°F (105°C).

Small-Frame Units (30U) with and without Battery Module(s)

20kVA 40kVA 60kVA

Recommended Installation Breaker Size 250A 250A 250A

Max Current 60A 120A 180A

Power and Ground Cable 250 MCM

120 mm

2

250 MCM

120 mm

2

250 MCM

120 mm

2

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m

Medium-Frame Units (42U) with and without Battery Module(s)

20kVA 40kVA 60kVA 80kVA

Recommended Installation Breaker Size 300A 300A 300A 300A

Max Current 60A 120A 180A 240A

Power and Ground Cable 300 MCM

150 mm

2

300 MCM

150 mm

2

300 MCM

150 mm

2

300 MCM

150 mm

2

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m

Large Frame (42U) without Battery Modules

20kVA 40kVA 60kVA 80kVA 100kVA 120kVA 140kVA

Recommended Installation Breaker Size 460A 460A 460A 460A 460A 460A 460A

Max Current 60A 120A 180A 240A 300A 360A 420A

Power and Ground Cable 600 MCM

300 mm²

600 MCM

300 mm²

600 MCM

300 mm²

600 MCM

300 mm²

600 MCM

300 mm²

600 MCM

300 mm²

600 MCM

300 mm²

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m

DC Input Maximum Current and Power Cable Conﬁguration

Nominal Battery Voltage: +/-120V DC

Small Frame (30U) with and without Battery Module(s)

20kVA 40kVA 60kVA

Recommended External Battery Breaker 100A 200A 300A

Power and Ground Cable 3 AWG

25 mm

2

4/0 AWG

95 mm

2

300 MCM

150 mm

2

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m

Medium Frame (42U) with and without Battery Module(s)

20kVA 40kVA 60kVA 80kVA

Recommended External Battery Breaker 100A 200A 300A 400A

Power and Ground Cable 3 AWG

25 mm

2

4/0 AWG

95 mm

2

300 MCM

150 mm

2

600 MCM

300 mm

2

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m

Large Frame (42U) without Battery Modules

20kVA 40kVA 60kVA 80kVA 100kVA 120kVA 140kVA

Recommended External Battery Breaker 100A 200A 300A 400A 500A 600A 700A

Power and Ground Cable 3 AWG

25 mm

2

4/0 AWG

95 mm

2

300 MCM

150 mm

2

500 MCM

240 mm

2

250 MCM x 2

120 mm

2

x 2

300 MCM x 2

150 mm

2

x 2

500 MCM x 2

240 mm

2

x 2

Fixation Torque Force 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m 2.26 N·m

15

7. Installation

7.2.1 Installing a Power Module

WARNING:

Ensure all Power Modules contain identical ﬁrmware versions prior to installation.

Each Power Module capacity is 20kVA/18kW and comprises:

• Power Factor Correction Rectiﬁer

• Battery Charger

• Inverter

• Control Circuit

Figure 7.2

The hot-swappable Power Module allows for quick maintenance and system expansion. A latch located at the front of each module ﬁxes and

locks the module in its assigned slot. To install the Power Module, follow the procedure below.

1. Using the DIP switch on the front panel of each Power Module, set the module ID (0-7). The module ID should be exclusive per module.

Note: The default position is 0 for all DIP switches.

Module ID Module DIP Switch

0 POWER

1 POWER

2 POWER

3 POWER

4 POWER

5 POWER

6 POWER

7 POWER

Table 7.1

2. Place the ready switch on the front panel of the Power Module in the unlocked position by rotating the knob counterclockwise.

3. Remove blanking panel and insert Power Module into its identiﬁed frame position and slide into cabinet (retain the four screws to install Power

Module in step 4).

16

7. Installation

4. Secure the module to the frame via the ﬁxing bracket using the four screws. Ensure both sides of the Power Module are secured to the frame.

5. Place the ready switch into the locked position by rotating the knob clockwise.

Note: For initial startup and powering on the UPS, refer to Section 9.1 Control Panel – Introduction After the UPS has been successfully powered ON, refer to

Section 9.3.6.2 System to adjust total power and redundancy settings of the UPS based on power modules installed.

If additional power modules are being installed after initial startup, you may skip Section 9.1 and go to Section 9.3.6.2 to adjust total power and redundancy settings.

The Power Module’s LED indicator displays its operational status as follows

No. Behavior LED Display

1 Indicates the system is abnormal FAULT – constant red LED

2 Indicates the parallel system is abnormal

FAULT – ﬂashing red LED

3 Normal operation of the Primary UPS POWER – ﬂashing green LED

4 Normal operation of the Subordinate UPS

POWER – constant green LED

7.2.2 Removing a Power Module

WARNING

Before removing any Power Module, ensure the remaining Power Modules can support the attached load and the UPS is in Line- or

Bypass-mode.

1. Place the ready switch on the Power Module’s front panel to the unlocked position by rotating the knob counterclockwise.

2. The red FAULT LED will illuminate to indicate the Power Module output is off and disconnected from the UPS.

3. Wait ﬁve minutes after unlocking the Power Module before servicing.

4. Remove the four screws used to attach to the ﬁxing bracket.

5. Completely remove the Power Module from the frame.

Notes:

• When a power module is removed from the frame, the Redundancy Set Fail alarm will sound. Refer to Section 9.3.6.2 System to adjust the Total Power and

Redundancy settings based on power modules removed.

• The Power Module is heavy and will require two or more people to move it.

• To replace a Power Module, refer to Section 11.1 Power Module Replacement.

7.2.3 Installing a Battery Module

Each Battery Module is comprised of four battery trays. Trays are shipped separately in individual boxes (four boxes per module), fully assembled.

Refer to Section 9.3.6.3 Battery for conﬁguring the Amh hour rating when adding Battery Modules. The default value is 18Ah. For medium and

small frames, each additional installed Battery Module (4 x trays) is 18Ah.

1. Insert battery tray into open slot in the frame position and slide into cabinet, ensuring the +/- connectors make full contact.

2. Secure each battery tray with two screws (provided in accessory bag).

Figure 7.3

7.2.4 Removing a Battery Module

Remove two bottom screws on front panel of the battery tray and pull out the Battery Module using the handle provided.

17

7. Installation

7.2.5 External Battery Cabinet Connection

Once the battery installation is completed, ensure the corrected nominal battery voltage (+/- 120V DC), battery capacity and maximum charging

current data is programmed into the LCD settings. If the actual installation settings differ from the default settings in the LCD, the UPS alarm may

sound continuously. See Section 9.3.6.3: Battery for details.

N

+

-

N

+

-

External

Battery

Input/Output

Breaker and

Disconnect

External battery

cabinet

External battery

cabinet

Back panel of Switch Unit

Figure 7.4

Once all modules are assembled and installation cabling is complete, switch the UPS main breaker on the front of the UPS to “On”. The UPS

system is now on bypass. Enter the Controls Screen on the Control Panel to place the UPS system in full operation. See Section 9.3.4 Control

Screen for details.

7.3 Cold Start

Start Up of the UPS System should be undertaken via the Control Panel. It is possible to start the UPS without an AC input via the “Cold Start”

button on the Power Module:

1. Press the “Cold Start” button as shown in the ﬁgure below.

Cold Start Button

POWER

Figure 7.5

2. The UPS will enter standby mode. Immediately press the “Power On/Off” button and hold for 2 seconds, and the UPS will enter Battery Mode.

The Inverter and Battery LEDs will be illuminated. Cold Start procedure is complete.

If more than one Power Module is installed in the frame, performing the cold start procedure on one will translate to all other Power Modules

installed automatically.

Note: The UPS system will function correctly upon initial startup. However, maximum system battery runtime will be available only after the UPS system has been

charged for approximately 24 hours.

18

7. Installation

7.4 Conduit Box Installation (for Small Frame Models)

1. Remove the terminal block cover located on the top-front of the UPS to access the UPS system’s input, output and grounding connection

terminals.

2. The terminal block cover will be replaced with the terminal conduit box found inside the UPS (see illustration).

3. Prepare the terminal box cover with circular cutouts to allow wiring conduits to pass through.

4. Attach the terminal box cover to the top of the UPS system after ﬂexible conduit has been attached.

Notes:

• Make sure the wires are tightly connected to the terminals.

• Cabling should be protected by ﬂexible conduit and routed through the appropriate knockouts in the terminal block cover.

• Conduit box part number: 103509A

Example of conduit

box with circular

cutouts installed

Example of conduit

box located inside

UPS frame

19

8. Manual Maintenance Bypass

The SmartOnline SV Series is equipped with both an automatic bypass and a Manual Maintenance Bypass, allowing the UPS system to be

bypassed without removing power from the attached load.

8.1 Transfer to Bypass via STS Module Connector from UPS Mode

Conﬁrm Bypass Mode is enabled via the LCD prior to performing Maintenance Bypass.

1. Open the front door and locate the Maintenance Bypass Breaker (Q2).

2. Remove the two screws covering the protective plate over the Maintenance Bypass Breaker (Q2).

3. Conﬁrm the UPS system is operating in bypass mode (LCD will show bypass path as below; bypass

LED will illuminate and an alarm will sound).

208.0V

Figure 8.2

4. Turn ON Maintenance Bypass Breaker (Q2).

5. Turn OFF Output Breaker (Q3).

6. Turn OFF Main Input Breaker (Q1).

7. Turn OFF Internal/External Battery Breakers.

The UPS system is now on Maintenance Bypass. It is now safe to perform routine maintenance, inspection and repairs to the UPS.

To return to normal operation, simply reverse the above steps:

1. Turn ON Internal/External Battery Breakers.

2. Turn ON Main Input Breaker (Q1).

3. Conﬁrm the UPS is in Bypass Mode (LCD will show bypass path and bypass LED will illuminate).

4. Turn ON Output Breaker (Q3).

5. Turn OFF Maintenance Bypass Breaker (Q2)

6. Replace the protective plate over the maintenance bypass breaker unit using the two screws provided.

7. Press the Power button for 2 seconds until the beep to start the inverter is heard.

8.2 Transfer to Bypass via Control Panel

1. Via the Home Screen on the Control Panel, use the Down/Right key to access Menu – Control.

2. Scroll down to “Transfer to Bypass”, select “YES” then press “Enter” key (also see Section 9.3.4 Control Screen).

3. The UPS will transfer to bypass mode; conﬁrm LCD shows bypass path and bypass LED is illuminated.

Note: The transfer to bypass Enable/Disable setting may only be changed when the inverter is turned OFF. The default setting is Enabled.

Figure 8.1

20

9. Control Panel

9.1 Introduction

Turn UPS ON

Once all modules are assembled and installation cabling is complete:

1. Switch on internal/external battery breakers.

2. Switch the UPS Main Breaker Q1 on the front of the breaker panel (“Bypass Mode” will display on the LCD panel).

3. Press the Power button for two seconds. The UPS will now be in Line Mode.

4. Switch on Output Breaker Q3. Parameters can now be viewed, adjusted and programmed via the control panel located on the front of the

UPS system.

Turn UPS OFF

WARNING: The UPS system shutdown procedure will eliminate the AC power output for all loads. Before shutdown, conﬁrm all power

loads are turned off.

1. Press the Power button for two seconds.

2. If the bypass is disabled, the UPS will transfer to Bypass Mode or Standby Mode.

Note: The UPS will have no output when in Standby Mode.

3. Switch off Output Breaker Q3.

4. Switch off Input Breaker Q1.

5. Wait one minute, then shut off battery breakers.

Note: UPS must be disconnected from AC input in order to be fully de-energized.

The Control Panel is the user control and interface for all measured parameters, UPS and battery status and alarms and is divided into three

areas:

1

LCD Display – Graphic display and all measured parameters

2

LED Indicators – refer to table 9.1

3

Control Keys – refer to table 9.2

1

3

2

Figure 9.1

LED Color Status Deﬁnition

INPUT Green On Input source is normal

Flashing Input source is abnormal

Off No input source

BYPASS Amber On Load is on bypass

Flashing Input source is abnormal

Off Bypass is not functioning

INVERTER Green On Load is on inverter

Off Inverter is not functioning

BATTERY Red On Load is on battery

Flashing Low battery

Off Normal operation, battery is charging

ALARM Red On UPS fault

Flashing UPS alarm

Off No alarms

Table 9.1

La page charge ...

Tripp Lite SmartOnline 208V SV-Series 3-Phase Modular UPS Systems Le manuel du propriétaire

Tripp Lite SmartOnline 208V SV-Series 3-Phase Modular UPS Systems Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents