Schneider Electric PowerLogic ION8650 Instruction Sheet

PowerLogic™ ION8650

Energy and power quality switchboard meter

Medidor de tablero de distribución de energía y de calidad

de energía

Compteur de tableau pour mesure de la qualité de l’énergie

Installation guide

Manual de instalación

Manuel d’installation

7ML02-0305-03

10/2021

ENGLISH

ESPAÑOLFRANÇAIS

English

Español

Français

Safety information ........................................................................................ 5

Overview ........................................................................................................ 9

Installation ................................................................................................... 14

Specifications .............................................................................................. 28

Appendix A: Additional setup options ...................................................... 30

Información de seguridad .......................................................................... 35

Descripción general .................................................................................... 39

Instalación ................................................................................................... 45

Especificaciones ......................................................................................... 62

Appendix A: Opciones adicionales de configuración ............................. 65

Informations de sécurité ............................................................................ 71

Général ......................................................................................................... 75

Installation ................................................................................................... 79

Spécifications .............................................................................................. 96

Appendix A: Options de configuration supplémentaires ....................... 98

ENGLISH

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with

the device before trying to install, operate, service or maintain it. The following

special messages may appear throughout this manual or on the equipment to warn

of potential hazards or to call attention to information that clarifies or simplifies a

procedure.

Please note

Electrical equipment should be installed, operated, serviced and maintained only by qualified

personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of

the use of this material.

A qualified person is one who has the skills and knowledge related to the construction, installation

and operation of electrical equipment and has received safety training to recognize and avoid the

hazards involved.

The addition of either symbol to a “Danger” or “Warning” safety label indicates that an

electrical hazard exists which will result in personal injury if the instructions are not

followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death

or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor

or moderate injury.

CAUTION

NOTICE

NOTICE is used to address practices not related to physical injury.

ENGLISH

Notices

Legal information

The Schneider Electric brand and any registered trademarks of Schneider Electric Industries SAS

referred to in this guide are the sole property of Schneider Electric SA and its subsidiaries. They may

not be used for any purpose without the owner's permission, given in writing. This guide and its

content are protected, within the meaning of the French intellectual property code (Code de la

propriété intellectuelle français, referred to hereafter as "the Code"), under the laws of copyright

covering texts, drawings and models, as well as by trademark law. You agree not to reproduce, other

than for your own personal, noncommercial use as defined in the Code, all or part of this guide on

any medium whatsoever without Schneider Electric’s permission, given in writing. You also agree not

to establish any hypertext links to this guide or its content. Schneider Electric does not grant any right

or license for the personal and noncommercial use of the guide or its content, except for a non-

exclusive license to consult it on an "as is" basis, at your own risk. All other rights are reserved.

Electrical equipment should be installed, operated, serviced and maintained only by qualified

personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of

the use of this material.

As standards, specifications and designs change from time to time, please ask for confirmation of the

information given in this publication.

FCC Part 15 notice

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encourages to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that any changes or modifications not expressly approved by Schneider Electric

could void the user’s authority to operate the equipment.

CAN ICES-3(B) /NMB-3(B)

FCC Part 68 notice

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the

Administrative Council for Terminal Attachments (ACTA). On the side of this equipment is a label that

contains, among other information, a product identifier in the format US: AAAEQ##TXXXX. If

requested, this number must be provided to the telephone company.

This equipment uses the following Universal Service Order Codes (“USOC”) jacks: RJ11.

A plug and jack used to connect this equipment to the premises wiring and telephone network must

comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug or compliant modular jack is provided with this product.

ENGLISH

The REN is used to determine the number of devices that may be connected to a telephone line.

Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming

call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the

number of devices that may be connected to a line, as determined by the total RENs, contact the local

telephone company. The REN for this product is part of the product identifier that has the format US:

AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a

REN of 0.3).

If this equipment, Digital Power Meter with Internal Modem, causes harm to the telephone network,

the telephone company will notify you in advance that service may be temporarily discontinued. When

advance notice is not practical, the telephone company will notify you as soon as possible. You will

also be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that

could affect the operation of this equipment. If this happens, the telephone company will provide

advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If you experience trouble with this equipment, Digital Power Meter with Internal Modem, please

contact Schneider Electric at 615-287-3400. If this equipment is causing harm to the telephone

network, the telephone company may request that you disconnect this equipment until the problem

is resolved.

There are no user serviceable parts in this equipment.

Connection to party line service is subject to state tariffs. Contact the state public utility commission,

public service commission or corporation commission for information.

If your premises has specially wired alarm equipment connected to the telephone line, ensure that

the installation of this Digital Power Meter with Internal Modem does not disable your alarm

equipment. If you have questions about what will disable alarm equipment, consult your telephone

company or a qualified installer.

Network compatibility notice for the internal modem

The internal modem in meters equipped with this option is compatible with the telephone systems of

most countries in the world, with the exception of Australia and New Zealand. Use in some countries

may require modification of the internal modem’s initialization strings. If problems using the modem

on your phone system occur, please contact Schneider Electric Technical Support.

Calibration compliance

Schneider Electric certifies that this product meets the published specifications and has been

calibrated and tested using equipment and standards traceable to the National Institute of Standards

and Technology (NIST) in the US or the National Research Council of Canada (NRC). For details,

refer to the Certificate of Calibration for this product.

Standards compliance

Made by Power Measurement Ltd.

N998

ENGLISH

ION8650 switchboard meter installation guide Overview

ENGLISH

Overview

The PowerLogic™ ION8650 advanced power and energy revenue meter features comprehensive

logging, advanced power quality measurement, multi-protocol and multi-port communications,

including IRIG-B support, and optional onboard and remote I/O capabilities.

This document outlines the steps for installing the FT-21 switchboard version of the ION8650 meter.

High accuracy metering considerations

In situations where the magnitude and quality of the voltage input source is insufficient (e.g.,

installations using PTs with low VA ratings or long conductor runs), consider using an auxiliary-

powered ION8650.

Additional information

For more information on the ION8650 meter, including documentation downloads and software

tools, visit www.se.com. Available technical documentation includes:

ION8650 socket meter installation guide - contains wiring and installation instructions for the socket

version of the ION8650 meter.

ION8650 accuracy verification technical note - details requirements and procedures for validating

the meter’s accuracy.

ION8650 user guide - contains detailed information on meter operation, meter firmware updates,

software support, communications, inputs/outputs, logging, time-of-use, alarm notification, and

other advanced features.

I/O Expander installation guide - describes the optional external I/O device that you can connect to

the ION8650, for additional digital I/O and analog output ports.

Product option documents - provide option-specific information about the various product options

you can order for the meter. They usually ship with the product.

Technical notes - provide instructions for using meter features and for creating custom

configurations.

Online ION Setup help - describes how to use the ION Setup meter configuration software.

ION Reference - explains the ION architecture and describes the operation and behavior of the

different ION modules available in ION hardware and ION software products.

Before you begin

1. Familiarize yourself with the contents of this guide, in particular the “Safety precautions” on

page 10 and “Specifications” on page 28.

2. Carefully unpack the meter from the box. The switchboard meter ships with the following:

3. Check that the part number on the front nameplate label matches the part number on your sales or

purchase order (see “Front panel label” on page 11):

4. Make sure you have all other required equipment and peripherals appropriate for your installation,

e.g., Ethernet or RS-232 to RS-485 converter, optical probe, revenue seal, etc.

A This installation guide B The meter’s calibration certificate

C Terminal screws, mounting nuts and washers

If you ordered the breakout cable form factor option, the following is also included:

DCOM breakout cable: 24-pin female Molex to female DB9 connector (RS-232), two sets of twisted pair

wires (RS-485)

EOptional Ethernet CAT5 female-to-female coupler (only if you ordered the Ethernet communications

option)

FOptional I/O breakout cable: a 16-pin female Molex to 16 bare-ended wires for connecting to I/O devices

(only if you ordered the onboard I/O option)

A

B

C

D

E

F

Overview ION8650 switchboard meter installation guide

ENGLISH

Recommended tools

Torque screwdriver with #2 Phillips and nut driver bits

Precision flat tip screwdriver

Wire cutter, stripper and crimper

Small needlenose pliers

ION Setup meter configuration software (download and install latest version from the website)

Safety precautions

Installation, wiring, testing and service must be performed in accordance with all local and national

electrical codes.

NOTE

Do not perform Dielectric (Hi-Pot) or Megger testing on the ION8650 because its internal surge protection circuitry

starts functioning at levels below typical Hi-Pot voltages. Contact your local Schneider Electric representative for

more information on device specifications and factory testing.

Available models

The ION8650 meter is available in three different models:

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

•Apply appropriate Personal Protective Equipment (PPE) and follow safe electrical work

practices. See NFPA 70E, CSA Z462 or other local standards

•Turn off all power supplying this device and the equipment in which it is installed before

working on or in the equipment.

•Always use a properly rated voltage sensing device to confirm that all power is off.

•Do not exceed the maximum ratings of this device.

•Do not use this device for critical control or protection of persons, animals, property or

equipment.

•Do not short secondary terminals of Voltage Transformer (VT)

•Do not open secondary terminals of Current Transformer (CT)

•Ground secondary circuit of CTs.

•Assume communications and IO wiring are hazardous live until determined otherwise.

•Do not perform Dielectric (Hi-Pot) or Megger testing on this device.

•Connect protective ground (earth) before turning on any power supplying this device.

•Replace all devices, doors and covers before turning on power to this equipment.

Failure to follow these instructions will result in death or serious injury.

Model1Memory Data recorders Description

ION8650A 128 MB 50 (800 channels) Class A power quality analysis meter with 1024 samples/cycle transient detection, Flicker,

PQ waveform support, interharmonics, EN50160 power quality monitoring and Modbus

mastering

ION8650B 64 MB 45 (720 channels) Class S compliant meter with EN50160 power quality monitoring and Modbus mastering

ION8650C 32 MB 5 (80 channels) Basic tariff/energy meter

1 Visit www.se.com for more information on the different models.

ION8650 switchboard meter installation guide Overview

ENGLISH

Meter options

The model number (shown in “Front panel label” on page 11) indicates the meter’s options.

Front panel label

Option Code Description

Power supply1E3-phase power supply (blade powered)2

M 8 6 5 0 A 4 C 0 H 6 C 1 B 0 A H Auxiliary power supply - Standard

JAuxiliary power supply - High voltage

Communications3A0 Front panel infrared optical port, RS-232/RS-485, RS-485

M8650A4C0H6C7A0A C7 Front panel infrared optical port, RS-232/RS-485, RS-485, Ethernet4, internal modem

E1 Front panel infrared optical port, RS-232/RS-485, RS-485, Ethernet4

M1 Front panel infrared optical port, RS-232/RS-485, RS-485, internal modem

I/O5A No digital I/O

M 8 6 5 0 A 4 C 0 H 6 C 1 B 0 A B 4 Form C solid state digital outputs, 3 Form A digital inputs

C 4 Form C solid state digital outputs, 1 Form A solid state digital output, 1 Form A digital input

D Ethernet outage notification

1Refer to “High accuracy metering considerations” on page 9 for recommendations when selecting a power supply option.

2The standard 3-phase power supply is powered from the meter’s voltage measurement connections. Ensure your system meets the meter’s steady state voltage

specifications.

3The ION8650C meter can communicate simultaneously only through a maximum of three ports (the infrared optical port, plus two other communications ports).

The ION8650A and ION8650B meters can communicate simultaneously through all communications ports.

4Some features require Ethernet communications. See “Ethernet option” on page 20 for a list of services.

5Additional inputs and outputs are available through the separately-ordered I/O Expander.

ATest amperage IVoltage transformer ratio (VTR)

BClass accuracy JCurrent transformer ratio (CTR)

CTest constant (LED pulse rate) KPrimary watthour constant

DFrequency LTransformer factor (VTR x CTR)

ECurrent range MMeter internal diagram (view from

front of meter)

FForm factor NANSI bar code

GVoltage input rating OModel number

HWiring configuration PSerial number

8650 METER

*ZYX00123456700000*

XX-1101X001-00 X8650X0X0X6X0X0X

V~

W

FM

CL

Freq

Kt

CA

TA VTR

CTR

PKh

Mult by

E

H

F

G

A

D

B

C

M

P

N

O

I

L

J

K

Overview ION8650 switchboard meter installation guide

ENGLISH

Front panel overview

Switchboard meter form factors

The switchboard meter fits in an FT-21 switchboard case cutout and is available in one of the following

switchboard case form factors:

Meter front with cover removed

AWatt pulser: A set of LEDs (infrared, red) used for real energy pulsing.

BVAR pulser: A set of LEDs (infrared, red) used for reactive energy pulsing.

CDemand reset switch: Resets the peak demand values logged in the meter. Can be

activated with the cover on or off.

DRound button (ALT/ENTER): Press to select a highlighted option. Also used to

toggle between NORM and ALT display modes. Press and hold to access Setup

menu.

E

Navigation buttons: Press the up or down buttons to scroll and highlight a different

menu item or to increase/decrease the value of a highlighted number. Press and

hold the up button to move the cursor to the left. Press and hold the down button to

move the cursor to the right.

FInfrared optical port

GMaster reset button: Located in a recessed button under the front label to prevent

accidental activation. You must remove the meter cover and its label to access it.

HTest mode button: Located under the front cover, this places the meter into Test

mode, ceasing accumulation of billable quantities.

IMeter LCD screen

AB

I

D

C

F

G

E

H

Meter case with breakout panel

See “Switchboard meter with rear breakout panel” on page 21 for details.

Rear panel provides:

• 14-pin Molex connector (for the external I/O Expander option)

• Spring-loaded captured wire connectors (for wiring RS-485

communications, IRIG-B and optional onboard I/O)

• DB9 male connector (RS-232 communications)

• RJ45 jack (Ethernet option)

• RJ11 telephone jack (modem option)

• power terminal strip (auxiliary power supply option)

Meter case with breakout cable

See “Switchboard meter with rear breakout cable” on page 22 for details.

Included cables:

• 24-pin Molex connector cable (used with the COM breakout cable for

RS-232 and RS-485 serial communications)

• 2-wire cable for wiring IRIG-B

Optional cables:

• Ethernet cable with RJ45 plug (Ethernet option)

• Telephone cable with RJ11 plug (modem option)

• 16-pin Molex connector cable (onboard I/O option)

• AC power cable (auxiliary power supply option)

ION8650 switchboard meter installation guide Overview

ENGLISH

Switchboard meter dimensions

FT-21 switchboard case with breakout panel

FT-21 switchboard case with breakout cable

147 mm (5.8 in)

66 mm

(2.6 in)

248 mm (9.8 in)

189 mm (7.4 in)

226 mm

(8.9 in)

59 mm

(2.3 in)

29 mm

(1.1 in)

14 mm (0.6 in)

28 mm (1.1 in)

41 mm (1.6 in)

113

mm

(4.4 in)

25 mm

(1.0 in)

29 mm

(1.2 in)

164 mm (6.4 in)

286 mm

(10.6 in)

165mm

6.5in

59mm

2.3in

171mm

6.7in

231mm

9.1in

268mm 10.6in

226mm

8.9in

119mm

4.7in

164mm

6.4in

25mm

1.0in

28mm

1.1in

14mm

.6in

41mm

1.6in

147mm

5.8in

29mm

1.1in

113mm

4.4in

29mm

1.1in

74mm

2.9in

29mm

1.2in

165 mm (6.5 in)

286 mm

(10.6 in)

226 mm

(8.9 in)

119 mm

(4.7 in)

171 mm (6.7 in)

231 mm (9.1 in)

59 mm

(2.3 in) 29 mm (1.2 in)

164 mm (6.4 in)

74 mm

(2.9 in)

29 mm

(1.2 in)

25 mm

(1.0 in)

113

mm

(4.4 in)

29

mm

(1.2 in)

14 mm (0.6 in)

28 mm (1.1 in)

41 mm (1.6 in)

147 mm (5.8 in)

Installation ION8650 switchboard meter installation guide

ENGLISH

Installation

Installation, wiring, testing and service must be performed in accordance with all local and national

electrical codes.

Step 1: Switchboard case installation

1. Disconnect and lock out power. Use a properly rated voltage sensing device to confirm that

power is off.

2. Prepare the mounting surface for the FT-21 case. Refer to the drawing for hole dimensions.

3. Place the meter on a sturdy surface. Locate the thumbscrew (A) at the bottom of the switchboard

cover and turn it counter-clockwise to release the cover.

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

•Apply appropriate Personal Protective Equipment (PPE) and follow safe electrical work

practices. See NFPA 70E, CSA Z462 or other local standards.

•Turn off all power supplying this device and the equipment in which it is installed before

working on or in the equipment.

•Always use a properly rated voltage sensing device to confirm that all power is off.

• Never bypass external fusing. Install properly rated fuses in voltage measurement circuits and

in auxiliary (control) power circuit.

• Do not exceed the device’s ratings for maximum limits. Use PTs (potential transformers) or VTs

(voltage transformers) as necessary.

• Never short the secondary of a PT or VT.

• Never open circuit a CT (current transformer); use the shorting block to short circuit the leads of

the CT before removing the connection from the device.

• Connect protective ground (earth) before turning on any power supplying this device.

• All electrical connections to the meter terminals must not be user-accessible after installation.

• Replace all devices, doors and covers before turning on power to this equipment.

Failure to follow these instructions will result in death or serious injury.

141mm [5.6 in]

149mm [5.9 in]

230 mm [9.1 in]

246 mm [9.7 in]

149 mm (5.9 in)

141 mm (5.6 in)

230 mm3 (9.1 in)

246 mm (9.7 in)

4x Ø6.35 mm

(Ø0.25 in)

B

AC

D

ION8650 switchboard meter installation guide Installation

ENGLISH

4. Pull the bottom of the cover slightly towards you and lift it up to unhook it from the top retaining tabs

(B). Set cover aside.

5. Push down and open all the lever contact switches (C).

6. Push the locking levers (D) to unlock the meter chassis (push up on the left lever, push down on

the right lever).

7. Grab the top bracket handle (E), then carefully slide out the meter chassis and set it aside.

8. Insert the FT-21 case into the mounting hole.

9. Secure the lockwashers and nuts (F) onto the rear mounting studs. Tighten with a hex socket

wrench or nut driver.

10. Align the meter chassis to the switchboard and carefully slide in the chassis, pushing forward on

the bottom half of the meter bezel to mate the meter and meter case rear connectors.

11. Pull the locking levers (G) to lock the meter chassis to the case (pull down on the left lever, pull up

on the right lever).

12. Push up and close all the lever contact switches (H).

13. Replace the cover, aligning the slots along the top with the retaining tabs (I) on the case.

14. Close the cover and hand-tighten the thumbscrew (J).

E

F

G

H

I

J

Installation ION8650 switchboard meter installation guide

ENGLISH

Step 2: Wire the switchboard case voltage and current inputs

Electrical wiring considerations

Install 2 A slow-blow fuses (customer supplied) in the voltage measurement input circuits as shown

in the following electrical wiring diagrams. The auxiliary power supply circuit, if applicable, must also

be fused. See “Step 4: Connect the optional auxiliary power” on page 20 for details.

NOTE

Built-in shorting blocks are provided within the FT-21 drawout case so when the meter is removed, the shorting

blocks automatically short-circuit the current inputs.

Using Potential Transformers

Volts mode and applicable wiring terminals

The following diagrams show which terminals on the back of the switchboard case are used when

wiring the Form 9, Form 29/Form 36 or Form 35 meter to your electrical system. You must set the

correct volts mode as shown below. See “Front panel setup menus” on page 24.

The following diagrams illustrate typical wiring conventions for the electrical service types supported

by the different ION8650 meter form factors. After completing all electrical wiring, mounting and

installation steps, refer to “Step 10: Use phasor diagrams to verify wiring” on page 26 for details on

meter operation for different systems and volts modes, as well as verification of correct phase wiring.

Wye system nominal voltage Requires PT Delta system nominal voltage Requires PT

120 Vac L-N or 208 Vac L-L no up to 480 Vac L-L no

277 Vac L-N or 480 Vac L-L no over 480 Vac L-L yes

347 Vac L-N or 600 Vac L-L yes

over 347 Vac L-N or 600 Vac L-L yes

Form 9

Volts mode = 9S 4-Wire Wye/Delta

Form 29 or Form 36

Volts mode = 29S 4-Wire Wye1

Form 35

Volts mode = 35S 3-Wire

1If you are using the switchboard meter in a Form 36 electrical wiring application, you must set the volts mode to 29S 4-Wire Wye.

ION8650 switchboard meter installation guide Installation

ENGLISH

Form 9 (3-element)

Set the meter’s Volts Mode to 9S - 4 Wire Wye/Delta. Voltage measurement limit is 57 to 277 VLN.

Form 9, 4-Wire Wye, no PTs, 3 CTs Form 9, 4-Wire Wye, 3 PTs, 3 CTs

Form 9, 3-Wire Wye, 3 PTs, 3 CTs Form 9, 3-Wire Wye, 3 PTs, 2 CTs

Form 9, 4-Wire Delta, no PTs, 3 CTs (Red/High Leg Delta)

NOTE

Before performing an installation using the Form 9, 4-Wire Delta

wiring configuration (diagram on left), see the Red/High Leg Delta

technical note (download at www.se.com).

B

N

CA

LOAD

LINE

LOAD

LINE

B

N

CA

LOAD

LINE

B

N

CA

LOAD

LINE

B

N

CA

B

C

A

N

LOAD

LINE

Installation ION8650 switchboard meter installation guide

ENGLISH

Form 29 or Form 36 (2½-element)

Set the meter’s Volts Mode to 29S - 4 Wire Wye. Voltage measurement limit is 57 to 277 VLN.

Form 35 (2-element)

Set the meter’s Volts Mode to 35S - 3 Wire. Voltage measurement limit is 120 to 480 VLL.

Form 29 or Form 36, 4-Wire Wye, no PTs, 3 CTs Form 29 or Form 36, 4-Wire Wye, 2 PTs, 3 CTs

2A

V1V3Vref I11 I12 I21 I22 I31 I32

A

B

C

N

A

B

C

N

LOAD

LINE

B

N

CA

V1V3Vref I11 I12 I21 I22 I31 I32

A

B

C

N

2A

A

B

C

N

LOAD

LINE

B

N

CA

Form 35, 3-Wire Delta, 2 PTs, 2 CTs Form 35, 4-Wire Wye, 2 PTs, 3 CTs1

1This configuration can affect some of the meter’s parameter calculations. Contact Technical Support for more details.

B

C

A

LOAD

LINE

LOAD

LINE

B

N

CA

ION8650 switchboard meter installation guide Installation

ENGLISH

Step 3: Prepare the ground connections

Proper grounding of the meter helps:

Provide a safe path to protective ground (earth)

Protect the electronic circuitry in the meter

Ensure and maintain meter accuracy

Properly operate noise filtering within the meter

Properly operate communications ports

Comply with all local and national regulations

1. Remove any paint, oxidation or other surface coating or contaminants that prevent proper

electrical ground connection.

2. Use a ring or spade connector and 2.08 mm2 (14 AWG) wire to connect the switchboard case

ground to protective ground (earth).

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

Do not connect Vref to ground when using the Form 35, 3-Wire Delta, No PTs, 2 CTs wiring

diagram.

Failure to follow these instructions will result in death or serious injury

Form 35, 3-Wire Delta, No PTs, 2 CTs

LOAD

LINE

B

C

A

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• The meter’s ground must be connected to protective ground (earth).

• Do not power up the meter until the ground is connected.

Failure to follow these instructions will result in death or serious injury.

Rear view of switchboard

with breakout panel option Rear view of switchboard

with breakout cable option

Installation ION8650 switchboard meter installation guide

ENGLISH

Step 4: Connect the optional auxiliary power

This section only applies if you ordered an auxiliary power supply option for your meter.

Install a properly-rated 3 A slow-blow fuse (customer supplied) on the L/+ terminal.

Do not install a fuse on the meter’s N/- terminal if the power supply source N/- terminal is

grounded.

Connect the G terminal to earth ground.

Step 5: Wire the communications and optional I/O

Front optical port

Use an IEC Type II optical probe to communicate using the meter’s front optical port.

Ethernet option

Below are the default IP service port settings for Ethernet communications.

NOTE

The Ethernet port settings are configurable. See the PowerLogic ION8650 User Guide for more information on

changing Ethernet port number assignments.

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Turn off all power supplying this device and the equipment in which it is installed before working

on the device or equipment.

• Always use a properly rated voltage sensing device to confirm that all power is off.

• Verify the meter’s power source meets the specifications for your meter’s power supply option.

Failure to follow these instructions will result in death or serious injury.

Auxiliary power cord

on breakout cable

Use the auxiliary power cord (with grounded

U-plug) to connect to properly rated

single-phase AC or DC power source.

Auxiliary power terminal

on breakout panel

Wire the auxiliary power terminal connectors to

properly rated single-phase AC or DC power

source using a wire type and gauge appropriate

for the supply voltage. Use ring or spade

connectors on the wire ends.

Ungrounded AC or DC

power supply source

GLL

Grounded AC or DC

power supply source

GLN

HAZARD OF UNINTENDED OPERATION

Do not use this device for critical control or protection applications where human or equipment

safety relies on the operation of the control circuit.

Failure to follow these instructions can result in death or serious injury.

ION over TCP Modbus RTU EtherGate (COM1) EtherGate (COM4) Modbus TCP DNP over TCP FTP IEC61850

7700 7701 7801 7802 502 20000 21 102

La page est en cours de chargement...

Schneider Electric PowerLogic ION8650 Instruction Sheet

Schneider Electric PowerLogic ION8650 Instruction Sheet

dans d''autres langues

Documents connexes

Autres documents