lyft SIT032B Scooter Interface Module Manuel utilisateur

Marque
lyft
Modèle
SIT032B Scooter Interface Module
Taper
Manuel utilisateur
Page 1 of 7
Scooter Interface Module
User Manual
Model: SIT032B
Lyft, Inc.
185 Berry St, San Francisco, CA 94107
Last Modified: 2022-07-22
Page 2 of 7
Table Of Contents
Contents
Table Of Contents ................................................................................................................ 2
FCC Notices ......................................................................................................................... 3
ISED Canada Compliance Statement ..................................................................................... 4
English ............................................................................................................................. 4
Français ........................................................................................................................... 4
Module Summary ................................................................................................................. 5
External Interfaces ............................................................................................................ 5
Installation Instructions ........................................................................................................ 5
Electrical Connections ....................................................................................................... 5
Mechanical Connections .................................................................................................... 6
Environmental Limits ............................................................................................................ 7
Page 3 of 7
FCC Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
When using the product, maintain a distance of 20cm from the body to ensure compliance
with RF exposure requirements.
Page 4 of 7
ISED Canada Compliance Statement
English
This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the
device.
Exposure to radio frequency energy. The radiated output power of this device meets the
limits of FCC/ISED Canada radio frequency exposure limits. This device should be operated with
a minimum separation distance of 20 cm (8 inches) between the equipment and a person’s
body.
Français
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne
doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
L’exposition à l’énergie radiofréquence. La puissance de sortie rayonnée de cet appareil
est conforme aux limites de la FCC/ISDE Canada limites d’exposition aux fréquences radio. Cet
appareil doit être utilisé avec une distance minimale de séparation de 20 cm entre l’appareil et
le corps d’une personne.
CAN ICES-003(B) / NMB-003(B)
Page 5 of 7
Module Summary
The Lyft SIT032B module provides wireless connectivity, location, and card reader functionality
for the Lyft SCT-03-0-x shared e-scooter. The module communicates with the controllers inside
of the scooter to control motor speed, braking, and lighting; and to report the status of the
scooter to an internet application over LTE.
This module is only intended to be used by Lyft for integration into their own products, and will
not be sold to other companies or to consumers. This module should not be used in any other
circumstances.
External Interfaces
The module exposes five external cables that connect to the shared scooter hardware. These
connectors are the following:
● Connector 1 (5 pins): Julet JL-F39-Z508JG Male
● Connector 2 (4 pins): Higo Z409BMP Male
● Connector 3 (2 pins): JST ZMR-02
● Connector 4 (3 pins): JST ZMR-03
● Connector 5 (3 pins): JST ZHR-03
Installation Instructions
The Module must only be installed on a host as approved by Lyft in the SCT-03-0-x
manufacturing SOP in order to ensure compliance with applicable FCC regulations. A brief
summary of the key electrical and mechanical connections is included below for reference.
Electrical Connections
The connectors on the module must be attached in this order:
1. Connector 2 (optional)
2. Connector 3
3. Connector 4
4. Connector 5
5. Connector 1
Caution should be observed when plugging in Connector 1, as this applies power to the system.
To prevent damage during bring-up, the Connector 1 power should be disabled while inserting
the connector.
Page 6 of 7
Mechanical Connections
The Module must be mechanically joined to the shared scooter to ensure that the signal and
power connectors are securely mated during motion. Screw threads are provided within the
device’s housing for secure attachment to the shared scooter base. The mechanical mount has
been designed to mate with a Lyft-designed custom, plastic plate that is affixed to the SCT-03-
0-x handlebar area.
The Module must be mounted by following the Lyft-approved manufacturing SOP in order to
ensure that the user is more than 70mm away from all radiating elements.
In addition, the Module must only be mounted to a stem that shares the same stem and
handlebar geometry as the SCT-03-0-x in order to ensure that the NFC antenna is isolated from
the metal in the scooter handlebar and stem.
Page 7 of 7
Environmental Limits
This module is intended for use in ambient operating temperatures ranging from -20C to 50C.
Operating Conditions
The device is intended for use between -20o C (-4o F) and 50o C (122o F)
Electrical Supply:
Parameter
Typical
Input Voltage
36V
Operating Current
0.3A Max
Power Draw
10W Max
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

lyft SIT032B Scooter Interface Module Manuel utilisateur

Marque
lyft
Modèle
SIT032B Scooter Interface Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents