lyft BIT012 Manuel utilisateur

Taper
Manuel utilisateur
Page 1 of 6
Bike Interface Module
User Manual
Model: BIT012
Lyft, Inc.
185 Berry St, San Francisco, CA 94107
Last Modified: 2022-07-22
Page 2 of 6
Table Of Contents
Contents
Table Of Contents ................................................................................................................................................. 2
FCC Notices ............................................................................................................................................................ 3
ISED Canada Compliance Statement ................................................................................................................. 4
English .................................................................................................................................................. 4
Français ............................................................................................................................................... 4
Introduction .............................................................................................................................................. 5
Operation ................................................................................................................................................. 5
Accessory List ......................................................................................................................................... 5
Safety Precautions .................................................................................................................................. 6
Operating Conditions ............................................................................................................................... 6
Page 3 of 6
FCC Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
When using the product, maintain a distance of 20cm from the body to ensure compliance
with RF exposure requirements.
Page 4 of 6
ISED Canada Compliance Statement
English
This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Exposure to radio frequency energy. The radiated output power of this device meets the
limits of FCC/ISED Canada radio frequency exposure limits. This device should be operated
with a minimum separation distance of 20 cm (8 inches) between the equipment and a
person’s body.
Français
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil
ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
L’exposition à l’énergie radiofréquence. La puissance de sortie rayonnée de cet appareil
est conforme aux limites de la FCC/ISDE Canada limites d’exposition aux fréquences radio.
Cet appareil doit être utilisé avec une distance minimale de séparation de 20 cm entre
l’appareil et le corps d’une personne.
CAN ICES-003(B) / NMB-003(B)
Page 5 of 6
Introduction
The bicycle interface module is responsible for providing user access to the Lyft e-bike.
Authentication, state and location is communicated to Lyft’s backend systems via commercial
mobility networks. The unit also displays the status of the e-bike and its available battery
capacity to the user.
Operation
The bicycle interface module is located on the rear fender and looks like this to the user:
The bike interface module features a battery level indicator, icons indicating if the bike is
locked or unlocked, and LED ring lights. A user activates a bike by interacting with the
interface module in two ways, either directly via the NFC transit card or by scanning the
applicable QR code into the Lyft app.
Accessory List
No accessories are to be used with this device.
Page 6 of 6
Safety Precautions
The module is not user serviceable. Do not open the bicycle interface module unless you are
explicitly authorized to do so and trained on how to do so by Lyft personnel.
Operating Conditions
The device is intended for use between -20o C (-4o F) and 50o C (122o F)
Electrical Supply:
Parameter
Typical
Input Voltage
36V
Operating Current
0.3A Max
Power Draw
10W Max
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

lyft BIT012 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues