Hach sensION+ EC5 Manuel utilisateur

DOC022.97.80143

sensION

™

+ Portable Meter

02/2013, Edition 3

User Manual

Manuel d'utilisation

Manual del usuario

Manual do usuário

用户手册

取扱説明書

사용 설명서

คูมือผูใช

English...................................................................................................................................................................................................

3

Français..............................................................................................................................................................................................18

Español...............................................................................................................................................................................................34

Português..........................................................................................................................................................................................50

中文.......................................................................................................................................................................................................66

日本語..................................................................................................................................................................................................80

한글.......................................................................................................................................................................................................95

ไทย........................................................................................................................................................................................................110

2

Table of contents

Specifications on page 3

General information on page 4

Installation on page 5

User interface and navigation on page 6

Startup on page 10

Operation on page 10

Maintenance on page 13

Troubleshooting on page 13

Replacement parts and accessories on page 15

Standard solutions on page 15

Salinity values for dissolved oxygen meters on page 17

Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions 18.6 x 7.3 x 3.8 cm (7.32 x 2.87 x 1.5 in.)

Weight 300 g (0.66 lb)

Meter enclosure IP67

Power requirements

(internal)

AA Alkaline or rechargeable Nickel Metal Hydride

(NiMH) batteries (3); battery life: over 500 hours

Input connectors MP-5 or MP-8 connector for sensION+ probes

Meter protection class Class III

Storage temperature –15 to +65 °C (5 to +149 °F)

Operating temperature 0 to 50 °C (32 to 122 °F)

Operating humidity 80% (non-condensing)

Specification Details

Instrument range pH: –2.00 to 19.99; ORP: ±1999 mV

Conductivity: 0.01 to 500 mS/cm; TDS: 0 to

500 g/L; Salinity: 0.0 to 1999 mg/L, 2.0 to 50.0 g/L

DO: 0.00 to 19.99 mg/L and 20.0 to 22.0 mg/L

(25°C), 0.0 to 199.9% and 200 to 250% (25°C)

Resolution pH: 0.01 pH; ORP: 1 mV (0.1 mV from –199.9 to

199.9 mV)

DO: 0.1% (1% if ≥ 200%); 0.01 mg/L (0.1 mg/L if ≥

20 mg/L)

Conductivity: changes with range (auto-ranging)

Temperature: 0.1 °C (0.1°F)

Measuring error (± 1 digit) pH: ≤ 0.01 pH; ORP: ≤ 1 mV

DO: ≤ 0.5% of the measured value

Conductivity: ≤ 0.5% (0.01 µS/cm to 19.99 mS/cm);

≤ 1% (≥ 20.0 mS). Salinity/TDS: ≤ 0.5%

Temperature: ≤ 0.2 °C (≤ 0.4 °F)

Reproducibility (± 1 digit) pH: ± 0.01 pH; ORP ± 1 mV

DO: ≤ 0.2 of the measured value

Conductivity/Salinity/TDS: ± 0.1%

Temperature ± 0.1 °C (± 0.1 °F)

Reference temperature

(RT)

Conductivity: 20 or 25 °C (68 or 77 °F) (factory

settings: 25 °C (77 °F))

Temperature coefficient

(TC)

Conductivity: 0.00 to 5.00%/°C (factory settings:

2%/ °C)

TDS conversion factor Conductivity: 0.00 to 4.44 (factory settings: 0.64)

Energy management Automatic power off after 5 minutes of inactivity

Certification CE

English 3

General information

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or

misuse of this product including, without limitation, direct, incidental and

consequential damages, and disclaims such damages to the full extent permitted

under applicable law. The user is solely responsible to identify critical application

risks and install appropriate mechanisms to protect processes during a possible

equipment malfunction.

Please read this entire manual before unpacking, setting up or operating

this equipment. Pay attention to all danger and caution statements.

Failure to do so could result in serious injury to the operator or damage

to the equipment.

Make sure that the protection provided by this equipment is not impaired.

Do not use or install this equipment in any manner other than that

specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will

result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided,

could result in death or serious injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument.

Information that requires special emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if not observed. A symbol on the

instrument is referenced in the manual with a precautionary statement.

This symbol, if noted on the instrument, references the instruction

manual for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed of

in European public disposal systems after 12 August of 2005. In

conformity with European local and national regulations (EU Directive

2002/96/EC), European electrical equipment users must now return

old or end-of-life equipment to the Producer for disposal at no charge

to the user.

Note: For return for recycling, please contact the equipment producer or supplier

for instructions on how to return end-of-life equipment, producer-supplied

electrical accessories, and all auxiliary items for proper disposal.

Product overview

The sensION

™

+ series meters are used with sensION+ probes to

measure various parameters in water. Primarily for field use, the portable

meter operates on three AA batteries.

The sensION

™

+ series meters are available in 6 models:

• sensION

™

+ EC5—conductivity, TDS, salinity and temperature meter

• sensION

™

+ MM150—pH, ORP (Redox), conductivity, TDS and

temperature meter

• sensION

™

+ MM110—pH, ORP (Redox) and temperature meter

• sensION

™

+ MM156—pH, conductivity, salinity, dissolved oxygen and

temperature meter

• sensION

™

+ pH1—pH meter

• sensION

™

+ DO6—dissolved oxygen (concentration and % saturation)

and temperature meter

Certification

Canadian Radio Interference-Causing Equipment Regulation,

IECS-003, Class A:

4 English

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la

réglementation canadienne sur les équipements provoquant des

interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device

complies with Part 15 of the FCC Rules. Operation is subject to the

following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications to this equipment not expressly approved by

the party responsible for compliance could void the user's authority to

operate the equipment. This equipment has been tested and found to

comply with the limits for a Class A digital device, pursuant to Part 15 of

the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference

to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference, in which case the user will be

required to correct the interference at their expense. The following

techniques can be used to reduce interference problems:

1. Disconnect the equipment from its power source to verify that it is or

is not the source of the interference.

2. If the equipment is connected to the same outlet as the device

experiencing interference, connect the equipment to a different

outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the

interference.

5. Try combinations of the above.

Installation

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks

described in this section of the document.

Install the batteries

W A R N I N G

Explosion hazard. Incorrect battery installation can cause the release of explosive

gases. Be sure that the batteries are of the same approved chemical type and

are inserted in the correct orientation. Do not mix new and used batteries.

N O T I C E

The battery compartment is not waterproof. If the battery compartment becomes

wet, remove and dry the batteries and dry the interior of the compartment. Check

the battery contacts for corrosion and clean them if necessary.

N O T I C E

When using nickel metal hydride (NiMH) batteries, the battery icon will not

indicate a full charge after freshly charged batteries have been inserted (NiMH

batteries are 1.2 V versus 1.5 V for alkaline batteries). Even though the icon does

not indicate complete charge, 2300 mAH NiMH batteries will achieve 90% of

instrument operation lifetime (before recharge) versus new alkaline batteries.

N O T I C E

To avoid potential damage to the meter from battery leakage, remove the meter

batteries prior to extended periods of non-use.

The meter can be powered with AA alkaline or rechargeable NiMH

batteries. To conserve battery life, the meter will power off after

5 minutes of inactivity. This time can be changed in the Display Options

menu.

English 5

For battery installation, refer to Figure 1.

Note: A tool such as a flat screwdriver may be necessary the first time the cover is

removed.

Make sure that the cover is tightly closed to maintain the IP67 enclosure

rating.

Figure 1 Battery installation

Connect a probe

1. Plug the probe into the meter (Figure 2).

2. Push the connector so that the alignment pin goes into the groove on

the female connector.

Note: Do not turn the connector.

Figure 2 Probe connection

User interface and navigation

User interface

Figure 3 Keypad description

1 CALIBRATION key 4 DOWN key: scroll to other options,

change a value

2 UP key: scroll to other options,

change a value

5 ON/OFF: turn on or turn off the

meter, DISPLAY LIGHT: turn on

and off the display light

3 MEASUREMENT key

6 English

Display description

The display shows 3 types of screens:

•

Measure—the most recent parameter measurement is shown with the

temperature and stabilization time.

• Calibration—the calibration standard values and temperature are

shown during a calibration.

• Standby—the screen is empty except for the measurement timer at

the bottom.

Figure 4 pH1 screen display

1 Main measurement value (pH or

ORP)

4 Measurement time (hh:mm:ss)

2 Main measurement units 5 Temperature

3 Battery indicator

Figure 5 DO6 screen display

1 Main measurement value (DO) 4 Measurement time (hh:mm:ss)

2 Main measurement units 5 Temperature

3 Battery indicator

English 7

Figure 6 MM110 screen display

1 Main measurement value (pH) 4 Main measurement time

(hh:mm:ss)

2 Measurement units 5 Temperature

3 Battery indicator 6 Main measurement value (ORP)

Figure 7 MM150 screen display

1 Main measurement value

(conductivity)

5 Measurement time (hh:mm:ss)

2 Main measurement value (pH) 6 Temperature

3 Main measurement units 7 Main measurement value (TDS,

ORP)

4 Battery indicator 8 Reference temperature

8 English

Figure 8 MM156 screen display

1 Main measurement value

(conductivity)

5 Measurement time (hh:mm:ss)

2 Main measurement value (pH) 6 Temperature

3 Main measurement units 7 Main measurement value (DO,

salinity)

4 Battery indicator 8 Reference temperature

Figure 9 EC5 screen display

1 Reference temperature 4 Battery indicator

2 Main measurement units 5 Measurement time (hh:mm:ss)

3 Temperature 6 Main measurement value

(conductivity, salinity, TDS)

Navigation

Use the calibrate key to calibrate the probe. Use the measure key

to take a sample measurement. Use the arrow keys to scroll to

other options or to change a value.

Some options require that a key be pushed and held or that multiple

keys be pushed at the same time. Be sure to look at the display during

tasks as the screens change quickly. Refer to each task for specific

instructions.

English 9

Startup

Turn the meter on and off

N O T I C E

Make sure that the probe is connected to the meter before the meter is turned on.

Push and hold to turn on or turn off the meter. If the meter does not

turn on, make sure that the batteries are properly installed.

Note: The meter is set to automatically power off after 5 minutes of inactivity to

maximize the battery life.

Operation

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and wear all of

the personal protective equipment appropriate to the chemicals that are handled.

Refer to the current material safety data sheets (MSDS) for safety protocols.

Setup for pH

The meter is ready for pH or ORP calibration without additional setup.

Setup for dissolved oxygen

Before calibration or measurement for dissolved oxygen, the probe must

be polarized and the settings for atmospheric pressure and salinity must

be entered.

Polarize the electrode

If the probe or batteries are disconnected, connect the probe or install

the batteries and wait for polarization:

Disconnect time Polarization time

< 5 minutes 10 minutes

5 to 15 minutes 45 minutes

> 15 minutes 6 hours

Change the settings

The settings for dissolved oxygen measurements can be changed when

a dissolved oxygen probe is used. Push to view the current settings.

1. Push . The first setting is shown.

2. Quickly use the arrow keys to change the value. Wait for the next

setting to be shown and change any additional values:

Option Description

Atmospheric pressure in mbar (default: 1013 mbar)

SAL Salinity in g/L NaCl (default: 0 g/L)

Aut: automatic (only in model MM156)

SEn Select the DO sensor model: 5120 or 5130

Note: The salinity value can be found from a conductivity measurement. Refer

to Table 3 on page

17.

Setup for conductivity

The settings for conductivity measurements can be changed when a

conductivity probe is used. Push

to view the current settings.

1. Push . The first setting is shown.

2. Quickly use the arrow keys to change the value. Wait for the next

setting to be shown and change any additional values:

Option Description

CEL Electrode type: platinum (default) or titanium.

Note: This option is not available on all meters.

CAL The number of standards for conductivity calibration. Select one

standard (default). Select the standard nearest to the expected

measurement range.

tC Temperature compensation: 0 to 9.99%/°C (default: 2%/°C)

tr Reference temperature: 20 or 25 °C (default: 25 °C)

F TDS calculation factor: 0.01 to 4.44 (default: 0.64)

10 English

The new settings are automatically stored in the meter.

Calibration

W A R N I N G

Chemical exposure hazard. Obey laboratory safety procedures and wear all of

the personal protective equipment appropriate to the chemicals that are handled.

Refer to the current material safety data sheets (MSDS) for safety protocols.

Calibration procedure

This procedure is for general use with liquid calibration solutions. Refer

to the documents that are included with each probe for additional

information.

1. Pour the buffers or calibration solution into the labeled calibration

tubes.

2. Rinse the probe with deionized water and put the probe into the

appropriate calibration tube. Make sure that there are no air bubbles

under the probe tip.

3. Push . The parameter flashes.

4. Use the arrow keys to change the parameter, if applicable.

5. Push to select the parameter.

6. Push the arrow keys to select the appropriate standard solution. For

pH, the buffers are automatically recognized.

7. Push to measure the calibration solution.

Note: For pH, the next calibration solution is shown. For conductivity, use one

calibration point. Select the standard nearest to the expected measurement

range.

8. Rinse the probe with deionized water and put the probe into the

second calibration tube, if applicable. Make sure that there are no air

bubbles under the probe tip.

9. Push to measure the second calibration solution, if applicable.

The next calibration solution is shown.

10. Rinse the probe with deionized water and put the probe into the third

calibration tube. Make sure that there are no air bubbles under the

probe tip.

11. Push to measure the third calibration solution, if applicable.

When the calibration is good, the display briefly shows OK and then

goes to the standby mode.

Note: To calibrate with only 1 or 2 standards when additional standards are

supplied, push after the first or second standard is measured.

View the calibration data

Data from the most recent calibration can be shown for pH, ORP and

conductivity.

1. Push .

2. Use the arrow keys to change the parameter, if necessary, and push

.

3. Push and at the same time. The calibration data is shown:

•

pH—the slope and offset values are shown alternating with the

deviation (in %) and calibration temperature.

• ORP—the measured mV value and calibration temperature are

shown.

• Conductivity—the cell constant and calibration temperature for

each standard are shown.

Restore the factory calibration

The user calibration can be erased and the factory calibration restored

for pH, ORP and conductivity.

1. Push

. The parameter flashes.

2. Use the arrow keys to change the parameter, if necessary.

3. Push and hold until OFF

is shown.

The factory calibration for the selected parameter is restored.

Adjust the calibration

The instrument can be adjusted to read a specified solution value for pH,

ORP and conductivity.

1. Rinse the probe. Put the probe in the solution.

2. Push

to read the value of the solution.

3. Push . The parameter flashes.

English 11

4. Use the arrow keys to select the parameter, if necessary.

5. Push and hold and then push .

The measured value flashes.

6. Use the arrow keys to change the value.

7. Push . The display shows OK.

Adjust the temperature

The temperature measurement can be adjusted at 25 °C (77 °F) and/or

85 °C (185 °F) to increase accuracy for pH, ORP and conductivity.

Note: Refer to the probe documentation to find the temperature limits for the probe

that is used.

1. Put the probe and a reference thermometer in a container of water at

approximately 25 °C and allow the temperature to stabilize.

2. Compare the temperature read by the meter with that of the

reference thermometer. The difference is the adjustment value for

the meter.

Example: reference thermometer: 24.5 °C; meter: 24.3 °C.

Adjustment value: 0.2 °C.

3. Enter the adjustment value for the 25 °C reading:

a. Push . The parameter flashes.

b. Use the arrow keys to select tEn.

c. Push . 25 °C is shown.

d. Push and then use the arrow keys to enter the adjustment

value for 25 °C. Push . 85 °C is shown.

4. Put the probe and a reference thermometer in a container of water at

approximately 85 °C and allow the temperature to stabilize.

5. Compare the temperature from the meter with that of the reference

thermometer. The difference is the adjustment value for the meter.

6. Push and then use the arrow keys to enter the adjustment value

for the 85 °C reading. Push .

About sample measurements

Each probe has specific preparation steps and procedures for taking

sample measurements. For step-by-step instructions, refer to the

documents that are included with the probe.

Push to take a sample measurement. During measurements, the

parameter flashes and the timer shows the stabilization time. To change

the measurement parameter (if applicable), push and hold

.

To measure the sample continuously, push 2 times. The parameter

flashes to indicate the continuous measurement mode.

Change the temperature units

The temperature units can be changed when the measurement screen is

shown.

1. Make sure that a stable measurement reading is shown.

2. Push and at the same time. The temperature units change to °C

or °F.

Disable the auto-shutoff option

The meter is set to automatically power off after 5 minutes of inactivity to

maximize the battery life. This option can be temporarily disabled.

1. Make sure that the meter is powered off.

2. Push and hold until the display shows OFF and no. The power

remains on indefinitely.

3. To power off the meter, push and hold until the display shows

OFF.

Note: The auto-shutoff option is enabled again when the meter is powered on

normally.

Set the backlight time

The display is illuminated when is pushed. The user can set the

length of time that the backlight stays on.

12 English

Note: The battery life is decreased when the backlight time is increased.

1. Make sure that the instrument is powered on.

2. Push and immediately push 2 times. The backlight time

flashes.

3. Push or to change the backlight time (range: 3 seconds to

2 minutes).

Maintenance

W A R N I N G

Multiple hazards. Do not disassemble the instrument for maintenance or service.

If the internal components must be cleaned or repaired, contact the

manufacturer.

C A U T I O N

Personal injury hazard. Only qualified personnel should conduct the tasks

described in this section of the manual.

Clean the instrument

N O T I C E

Never use cleaning agents such as turpentine, acetone or similar products to

clean the instrument including the display and accessories.

Clean the exterior of the instrument with a moist cloth and a mild soap

solution.

Store the meter

N O T I C E

To avoid potential damage to the meter from battery leakage, remove the meter

batteries prior to extended periods of non-use.

Replace the batteries

W A R N I N G

Explosion hazard. Incorrect battery installation can cause the release of explosive

gases. Be sure that the batteries are of the same approved chemical type and

are inserted in the correct orientation. Do not mix new and used batteries.

For battery replacement, refer to Figure 10.

Figure 10 Battery replacement

Troubleshooting

Refer to the following table for common problem messages or

symptoms, possible causes and corrective actions.

English 13

Error/Warning Description Solution

Measurement out

of range.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

Battery is low. Insert new batteries.

E1 Unstable reading

during a stability

measurement or

during calibration.

Make sure that the probe is properly

immersed in the sample.

E2 Probe current:

exceeded upper

limit during

measurement ≥

250 nA.

• Clean the probe and the membrane.

•

Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

E2 pH probes

sensitivity out of

range (accepted

values 70–105%).

• Make sure that the correct probe is

connected to the meter.

• Connect a new probe.

Error/Warning Description Solution

E2 During calibration,

the difference

between the

constants gets >

30%.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Connect a new probe.

E3 During calibration,

the cell constant

gets < 0.05 cm

-1

.

• Insert the probe into the appropriate

standard and read again.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

E3 Slope out of range

(accepted values ±

58 mV).

Connect a new probe.

E4 Buffer solution not

recognized.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Make sure that the buffer used

matches the buffer specified in

configuration.

• Replace the buffer solution.

• Make sure of the temperature

specification in configuration.

14 English

Error/Warning Description Solution

E4 Salinity cannot be

calculated TC=0

Modify TC

E5 Same buffer

solutions.

• Clean the probe and the membrane.

• Make sure that there are no air

bubbles in the membrane.

• Disconnect the probe and then

connect the probe again.

• Connect a different probe to verify if

problem is with probe or meter.

• Make sure that the buffer used

matches the buffer specified in

configuration.

• Replace the buffer solution.

• Make sure of the temperature

specification in configuration.

E6 The calibration

solutions have

different

temperatures.

Make sure that the calibration solutions

have the same temperature.

ErA (only

MM156)

Salinity is set to

automatic and

measured value >

50 g/L.

Modify TC

Replacement parts and accessories

Note: Product and Article numbers may vary for some selling regions. Contact the

appropriate distributor or refer to the company website for contact information.

Replacement parts

Description Item no.

Batteries, Alkaline AA 1938004

Carrying case LZW9990.99

Accessories

Description Item no.

Electrolyte for DO probe 51 20, 25 mL LZW9811.99

Electrolyte for DO probe 51 30, 50 ml 2759126

Tube for DO probe calibration LZW5123.99

Service kit for 51 30 DO probe (contains 2 membrane

modules and DO filling solution)

5196800

Replacement DO membrane for DO probe 51 20 LZW5125.99

147 μS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9701.99

1413 μS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9711.99

12.88 mS/cm standard solution (at 25 °C, 77 °F), 125 mL

bottle

LZW9721.99

Set of calibration tubes, 147 μS/cm, 1413 μS/cm and

12.88 mS/cm

LZW9138.99

220 mV standard solution, 125 mL LZW9402.99

Buffer solution pH 4.01, 125 mL LZW9460.99

Buffer solution pH 7.00, 125 mL LZW9461.97

Buffer solution pH 10.01, 125 mL LZW9470.99

Electrolyte solution, KCI 3M, 50 mL LZW9509.99

Calibration tubes pH 4.01, pH 7.00 and pH 10.01 LZW9137.97

Tube for ORP standard calibration 220 mV LZW9136.99

Work protector for electrodes 50 51 T and 50 52 T LZW9162.99

Standard solutions

Technical buffer solutions (DIN 19267)

Refer to Table 1 pH and ORP (mV) values of specific buffer sets at

varying temperatures.

English 15

Table 1 pH, ORP (mV) and temperature values

Temperature pH mV

°C °F

0 32 2.01 4.01 7.12 9.52 10.30 —

10 50 2.01 4.00 7.06 9.38 10.17 245

20 68 2.00 4.00 7.02 9.26 10.06 228

25 77 2.00 4.01 7.00 9.21 10.01 220

30 86 2.00 4.01 6.99 9.16 9.96 212

40 104 2.00 4.03 6.97 9.06 9.88 195

50 122 2.00 4.06 6.97 8.99 9.82 178

60 140 2.00 4.10 6.98 8.93 9.76 160

70 158 2.01 4.16 7.00 8.88 — —

80 176 2.01 4.22 7.04 8.83 — —

90 194 2.01 4.30 7.09 8.79 — —

Conductivity standard solutions

Refer to Table 2 for conductivity values of standard solutions at varying

temperatures.

Table 2 Conductivity and temperature values

Temperature Conductivity (EC)

°C °F µS/cm µS/cm mS/cm mS/cm

15.0 59 119 1147 10.48 92.5

16.0 60.8 122 1173 10.72 94.4

17.0 62.6 125 1199 10.95 96.3

18.0 64.4 127 1225 11.19 98.2

19.0 66.2 130 1251 11.43 100.1

Table 2 Conductivity and temperature values (continued)

Temperature Conductivity (EC)

°C °F µS/cm µS/cm mS/cm mS/cm

20.0 68 133 1278 11.67 102.1

21.0 69.8 136 1305 11.91 104.0

22.0 71.6 139 1332 12.15 105.4

23.0 73.4 142 1359 12.39 107.9

24.0 75.2 145 1386 12.64 109.8

25.0 77 147 1413 12.88 111.8

26.0 78.8 150 1440 13.13 113.8

27.0 80.6 153 1467 13.37 115.7

28.0 82.4 156 1494 13.62 —

29.0 84.2 159 1522 13.87 —

30.0 86 162 1549 14.12 —

31.0 87.8 165 1581 14.37 —

32.0 89.6 168 1609 14.62 —

33.0 91.4 171 1638 14.88 —

34.0 93.2 174 1667 15.13 —

35.0 95 177 1696 15.39 —

16 English

Salinity values for dissolved oxygen meters

Table 3 can be used to convert conductivity values to salinity for

dissolved oxygen meters.

Table 3 Conversion from conductivity to salinity

Conductivity (mS/cm) Salinity (g/L NaCl)

1.9 1.0

3.7 2.0

7.3 4.0

10.9 6.0

17.8 10.1

25.8 15.1

33.6 20.2

41.2 25.4

48.9 30.6

56.3 35.8

62.2 40.0

69.4 45.3

75.7 50.0

English 17

Table des matières

Caractéristiques à la page 18

Généralités à la page 19

Installation à la page 20

Interface utilisateur et navigation à la page 22

Mise en marche à la page 25

Fonctionnement à la page 25

Maintenance à la page 29

Dépannage à la page 29

Pièces de rechange et accessoires à la page 31

Solutions étalons à la page 32

Valeurs de salinité pour sondes à oxygène dissous à la page 33

Caractéristiques

Les caractéristiques techniques peuvent être modifiées sans préavis.

Caractéristique Détails

Dimensions 18,6 x 7,3 x 3,8 cm (7,32 x 2,87 x 1,5 pouces)

Poids 300 g (0,66 lb)

Boîtier de l'appareil IP67

Alimentation (interne) (3) piles alcalines AA ou rechargeables Nickel

Métal hybride (NiMH) ; durée de vie des piles :

plus de 500 heures

Connecteurs d'entrée Connecteur MP-5 ou MP-8 pour les sondes

sensION+

Classe de protection de

l'instrument

Classe III

Température de stockage –15 à +65 °C (5 à +149 °F)

Température de

fonctionnement

0 à 50 °C

Humidité de fonctionnement max. 80% (sans condensation)

Caractéristique Détails

Plage de l'appareil de

mesure

pH : –2,00 à 19,99 ; Eh : ±1 999 mV

Conductivité : 0,01 à 500 mS/cm ; TDS : 0 à

500 g/l ; salinité : 0,0 à 1 999 mg/l, 2,0 à 50,0 g/l

DO : 0,00 à 19,99 mg/l et 20,0 à 22,0 mg/l

(25 °C), 0,0 à 199,9 % et 200 à 250 % (25 °C)

Résolution pH : 0,01 pH ; Eh : 1 mV (0,1 mV de –199,9 à

199,9 mV)

DO : 0,1 % (1 % si ≥ 200 %) ; 0,01 mg/l (0,1 mg/l

si ≥ 20 mg/l)

Conductivité : varie avec la plage (plage auto)

Température : 0,1 °C (0,1 °F)

Erreur de mesure

(± 1 chiffre)

pH : ≤ 0,01 pH ; Eh : ≤ 1 mV

DO : ≤ 0,5 de la valeur mesurée

Conductivité : ≤ 0.5% (de 0,01 µS/cm à

19,99 mS/cm) ; ≤ 1 % (≥ 20 mS). /TDS (Facteur

TDS) :

Température : ≤ 0,2 °C (≤ 0,4 °F)

Reproductibilité (± 1 chiffre) pH : ± 0,01 pH ; Eh : ± 1 mV

DO : ≤ 0,2 de la valeur mesurée

Conductivité/Salinité/TDS : ± 0,1 %

Température : ± 0,1 °C (± 0,1 °F)

Température de référence

(RT)

Conductivité : 20 ou 25 °C (68 ou 77 °F)

(réglages d'usine : 25 °C (77 °F))

Coefficient de température

(TC)

Conductivité : 0,00 à 5,00 %/°C (réglages

d'usine : 2 %/°C)

Facteur de conversion TDS Conductivité : 0,00 à 4,44 (réglages d'usine :

0,64)

18 Français

Caractéristique Détails

Gestion de l'énergie Arrêt automatique au bout de 5 minutes

d'inactivité

Certification CE

Généralités

Les éditions révisées se trouvent sur le site Internet du fabricant.

Consignes de sécurité

A V I S

Le fabricant décline toute responsabilité quant aux dégâts liés à une application

ou un usage inappropriés de ce produit, y compris, sans toutefois s'y limiter, des

dommages directs ou indirects, ainsi que des dommages consécutifs, et rejette

toute responsabilité quant à ces dommages dans la mesure où la loi applicable le

permet. L'utilisateur est seul responsable de la vérification des risques

d'application critiques et de la mise en place de mécanismes de protection des

processus en cas de défaillance de l'équipement.

Veuillez lire l'ensemble du manuel avant le déballage, la configuration ou

la mise en fonctionnement de cet appareil. Respectez toutes les

déclarations de prudence et d'attention. Le non-respect de cette

procédure peut conduire à des blessures graves de l'opérateur ou à des

dégâts sur le matériel.

Assurez-vous que la protection fournie avec cet appareil n'est pas

défaillante. N'utilisez ni n'installez cet appareil d'une façon différente de

celle décrite dans ce manuel.

Interprétation des indications de risques

D A N G E R

Indique une situation de danger potentiel ou imminent qui, si elle n'est pas évitée,

entraîne des blessures graves, voire mortelles.

A V E R T I S S E M E N T

Indique une situation de danger potentiel ou imminent qui, si elle n'est pas évitée,

peut entraîner des blessures graves, voire mortelles.

A T T E N T I O N

Indique une situation de danger potentiel qui peut entraîner des blessures

mineures ou légères.

A V I S

Indique une situation qui, si elle n'est pas évitée, peut occasionner

l'endommagement du matériel. Informations nécessitant une attention

particulière.

Etiquettes de mise en garde

Lisez toutes les étiquettes et tous les repères apposés sur l'instrument.

Des personnes peuvent se blesser et le matériel peut être endommagé

si ces instructions ne sont pas respectées. Un symbole sur l'appareil est

désigné dans le manuel avec une instruction de mise en garde.

Si l'appareil comporte ce symbole, reportez-vous au manuel

d'utilisation pour consulter les informations de fonctionnement et de

sécurité.

En Europe, depuis le 12 août 2005, les appareils électriques

comportant ce symbole ne doivent pas être jetés avec les autres

déchets. Conformément à la réglementation nationale et européenne

(Directive 2002/96/CE), les appareils électriques doivent désormais

être, à la fin de leur service, renvoyés par les utilisateurs au fabricant,

qui se chargera de les éliminer à ses frais.

Remarque : Pour le retour à des fins de recyclage, veuillez contacter le fabricant

ou le fournisseur d'équipement pour obtenir les instructions sur la façon de

renvoyer l'équipement usagé, les accessoires électriques fournis par le fabricant,

et tous les articles auxiliaires pour une mise au rebut appropriée.

Présentation du produit

Les appareils de mesure portables de la série sensION

™

+ s'utilisent

avec des sondes numériques sensION

™

+ pour mesurer différents

paramètres dans l'eau. Essentiellement destinés à l'utilisation sur le

terrain, ces appareils de mesure portables fonctionnent avec trois piles

AA.

Les appareils de mesure de la série sensION

™

+ sont disponibles en

6 modèles :

Français 19

• sensION

™

+ EC5- appareil de mesure de conductivité, TDS, salinité et

température

•

sensION

™

+ MM150- appareil de mesure de pH, Eh (Redox),

conductivité, TDS et température

• sensION

™

+ MM110- appareil de mesure de pH, Eh (Redox) et

température

• sensION

™

+ MM156—instrument de mesure du pH, de la conductivité,

de la salinité, de l'oxygène dissous et de la température

• sensION

™

+ pH1-appareil de mesure de pH

• sensION

™

+ DO6- appareil de mesure d'oxygène dissous

(concentration et % saturation) et de température

Certification

Règlement canadien sur les équipements causant des

interférences radio, IECS-003, Classe A:

Les données d'essai correspondantes sont conservées chez le

constructeur.

Cet appareil numérique de classe A respecte toutes les exigences du

Règlement sur le matériel brouilleur du Canada.

Cet appareil numérique de classe A répond à toutes les exigences de la

réglementation canadienne sur les équipements provoquant des

interférences.

FCC part 15, limites de classe A :

Les données d'essai correspondantes sont conservées chez le

constructeur. L'appareil est conforme à la partie 15 de la règlementation

FCC. Le fonctionnement est soumis aux conditions suivantes :

1. Cet équipement ne peut pas causer d'interférence nuisible.

2. Cet équipement doit accepter toutes les interférences reçues, y

compris celles qui pourraient entraîner un fonctionnement inattendu.

Les modifications de cet équipement qui n’ont pas été expressément

approuvées par le responsable de la conformité aux limites pourraient

annuler l’autorité dont l’utilisateur dispose pour utiliser cet équipement.

Cet équipement a été testé et déclaré conforme aux limites définies pour

les appareils numériques de classe A, conformément à la section 15 de

la réglementation FCC. Ces limites ont pour but de fournir une protection

raisonnable contre les interférences néfastes lorsque l’équipement

fonctionne dans un environnement commercial. Cet équipement génère,

utilise et peut irradier l'énergie des fréquences radio et, s'il n'est pas

installé ou utilisé conformément au mode d'emploi, il peut entraîner des

interférences dangereuses pour les communications radio. Le

fonctionnement de cet équipement dans une zone résidentielle risque de

causer des interférences nuisibles, dans ce cas l'utilisateur doit corriger

les interférences à ses frais Les techniques ci-dessous peuvent

permettre de réduire les problèmes d'interférences :

1. Débrancher l'équipement de la prise de courant pour vérifier s'il est

ou non la source des perturbations

2. Si l'équipement est branché sur le même circuit de prises que

l'appareil qui subit des interférences, branchez l'équipement sur un

circuit différent.

3. Éloigner l'équipement du dispositif qui reçoit l'interférence.

4. Repositionner l’antenne de réception du périphérique qui reçoit les

interférences.

5. Essayer plusieurs des techniques ci-dessus à la fois.

Installation

A T T E N T I O N

Dangers multiples. Seul le personnel qualifié doit effectuer les tâches

détaillées dans cette section du document.

20 Français

La page charge ...

Hach sensION+ EC5 Manuel utilisateur

Ce manuel convient également à

Hach sensION+ EC5 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents