Uniden GMR2035-2 Le manuel du propriétaire

Catégorie
Radios bidirectionnelles
Taper
Le manuel du propriétaire

Ce manuel convient également à

S R F
yaw-2
soidar
GMR2035-2
GMR2050-2C
22 FRS Channels Battery Strength
Meter
Long Battery Life Call Button
Up to 20-mile Range* DC IN 5V
Channel Scan Channel Monitor
* Range may vary depending on environmental
and/or topographical conditions.
Note:This product is considered FRS only with 22
FRS channels in the US market.
1
2
3
4
5
6
7
8
9
10
1 Antenna 6 Microphone
2 USB Charge Jack 7 Speaker
3 Push to Talk 8 Channel/Power
4 Channel/Volume
Up
9 Call/Monitor Key
5 Channel/Volume
Down
10 Display
Congratulations on your purchase of the
Uniden GMR2035-2 or GMR2050-2C
(General Mobile Radio) radio. This
lightweight, palm-sized radio is a state-of-
the-art device, equipped with many
valuable features. Use it at sporting
events, to stay in contact with family and
friends, hiking, skiing, outdoors, or in a
neighborhood watch for vital
communication.
Your package contains the 2 radios, 6
AAA rechargeable NiMH batteries
(GMR2050-2C) or 6 AAA alkaline
batteries (GMR2035-2), one USB charge
cable (GMR2050-2C), this reference
guide, and 2 belt clips. To order the
following optional accessories, visit our
web site at www.uniden.com.
Use only Uniden accessories.
Each radio uses 3 AAA batteries for
power. GMR2035-2 uses non-
rechargeable alkaline batteries and
GMR2050-2C uses rechargeable NiMH
batteries. These batteries are supplied
with your radio.
To install the batteries:
1. Make sure your radio is OFF.
2. Remove the battery compartment
door by pressing on and sliding the
compartment door, and remove the
cover.
3. Install the supplied 3 AAA batteries
into the battery compartment. Be
certain to follow the + and – symbols
in the compartment. Installing the
batteries incorrectly will prevent the
unit from operating.
4. Replace the battery compartment
door by sliding the door into place.
5. Repeat for each radio.
Note: Do not mix rechargeable and
Alkaline batteries
CHARGING THE RADIO
GMR2050-2C only
1. Plug one branch of the microSD
Y-Cable into each radio's microSD
charge port.
2. Insert the other end (USB) into a
USB power source (computer, phone
PACKAGE CONTENTS
FCC GMRS LICENSE
INSTALL THE BATTERIES
charger, etc - not included).
Notes:
Install the batteries before charging.
Charge time may vary depending on the
battery life remaining. For fastest
charging, turn off the radio before
charging. (GMR2050-2C only).
Do not attempt to recharge alkaline
batteries. Doing so can create a safety
hazard or damage the radio.
If battery power is low, you cannot
operate the radio even using external
power. If you try to transmit while power
is low, the radio will automatically turn
off. Recharge the batteries.
USING THE RADIO
In order to get the most out of your new
radio, read this reference guide completely
before attempting to operate the radio.
Turning the Radio On and Adjusting the
Volume
1. Press and hold the CH/ key to turn
the radio ON.
2. To change the volume level, press the
or key to increase or decrease
the volume level.
3. Press and hold the CH/ key to turn
the radio OFF.
Choosing a Channel
Your radio has 22 channels you can use to
talk to others. In order to speak to
someone, each of you must be set to the
same channel.
To choose a channel:
Tap the CH/ key to turn the radio on,
then use the ▲ or ▼ key to select a
channel.
Channel Scan Feature
Your radio has a channel scan feature that
allows you to easily scan all 22 channels.
When an active channel is detected, the
unit pauses on that channel until the
channel is clear. Then, after a 2 second
delay, the radio continues scanning.
When the unit stops on an active channel,
you can press the PTT button on the
microphone to transmit on that channel.
To turn ON channel scan
Tap CH/ then hold for 3 seconds.
The channels will cycle down through all
22 chanels. To reverse scan direction, tap
▲. To stop scanning, press CH/ .
Talking on Your Radio
To talk to others using the radio:
1. Press and hold the PTT button and
speak in a clear, normal voice about
2-3 inches away from the
microphone. (While you are
transmitting, the tx icon displays. To
avoid cutting off the first part of your
transmission, pause slightly after
pressing the PTT button before you
start talking.)
2. When you are finished speaking,
release the PTT button. You can now
receive incoming calls. While
receiving, the rx icon displays.
Transmitting a Call Alert Tone
Your radio is equipped with a call tone that
will be transmitted when the CALL/MON
key is pressed.
To transmit the call tone, tap the CALL/
MON key. The tone will be transmitted.
Auto Squelch Feature
The radio is equipped with an automatic
squelch system which shuts off weak
transmissions and unwanted noise due to
terrain conditions or range limitations.
Monitor Mode Feature
Your radio allows you to listen for weak
signals on the current channel at the press
of a key.
To turn ON monitor mode:
Press and hold the CALL/MON key for 2
seconds. On a channel that does not
activity, you will hear only an open-squelch
hissing noise
To turn OFF monitor mode:
Press the CALL/MON key for 2 seconds
again. .
Channels 22 FRS
Operating
Frequency
UHF 462.5500 - 467.7125 MHz
Power
Source
3 AAA NiMH Batteries per radio
(GMR2050-2C)
3 AAA Alkaline Batteries per
radio (GMR2035-2)
Battery Life 8 Hours typical
Frequency Chart
CH Freq.[MHz] -
Cross Ref.
CH Freq.[MHz] -
Cross Ref.
1 462.5625 - FRS &
GMRS 1
12 467.6625 - FRS 12
2 462.5875 - FRS &
GMRS 2
13 467.6875 - FRS 13
3 462.6125 - FRS &
GMRS 3
14 467.7125 - FRS 14
4 462.6375 - FRS &
GMRS 4
15 462.5500 - GMRS
11
5 462.6625 - FRS &
GMRS 5
16 462.5750 - GMRS
8
6 462.6875- FRS &
GMRS 6
17 462.6000 - GMRS
12
7 462.7125 - FRS &
GMRS 7
18 462.6250 - GMRS
9
8 467.5625 - FRS 8 19 462.6500 - GMRS
13
9 467.5875 - FRS 9 20 462.6750 - GMRS
10
10 467.6125 - FRS 10 21 462.7000 - GMRS
14
11 467.6375 - FRS 11 22 462.7250 - GMRS
15
Note:This product is considered FRS only with
22 FRS channels in the US market.It is
considered a GMRS prodct in the
Canadian market.
MAINTENANCE
To be safe and sure:
Never open your radio’s case.
Never change or replace anything in your
radio except the batteries.
Care and Safety
To clean the radio, use a soft cloth dampened
with water. Do not use cleaners or solvents
SPECIFICATIONS
because they can harm the body of the unit and
leak inside, causing permanent damage. Use a
dry, lint-free cloth to clean the battery contacts.
Do not submerge the unit in water. If the unit
gets wet, turn it off and remove the batteries
immediately.
Dry the battery compartment with a soft cloth to
minimize potential water damage. Leave the
battery compartment cover off overnight to
ensure complete drying. Do not use the radio
until the unit is completely dry.
Your radio might cause TV or radio interference
even when it is operating properly. To determine
whether your radio is causing the interference,
turn it off. If the interference goes away, your
radio is causing it. Try to eliminate the
interference by moving your radio away from the
receiver. If you cannot eliminate the interference,
the FCC requires that you stop using the radio.
Hazardous Environments
Do not operate the radio in hazardous
environments. Explosion or fire may result. Do
not operate the radio near unshielded electrical
blasting caps.
Under certain conditions, radios can interfere
with blasting operations and may cause an
explosion. Turn your radio OFF to prevent
accidental transmission when in a blasting area
or in areas posted: "Turn off two-way radio."
Construction crews often use remote control RF
devices to set off explosives.
WARNING! Read this information before using
the radio. In August 1996 the Federal
Communications Commission (FCC) of the
United States with its action in Report and Order
FCC 96-326 adopted an updated safety
standard for human exposure to radio frequency
electromagnetic energy emitted by FCC
regulated transmitters.
Those guidelines are consistent with the safety
standard previously set by both U.S. and
international standards bodies. The design of the
radio complies with the FCC guidelines and
these international standards.
Never allow children to operate the radio without
adult supervision and the knowledge of the
following guidelines.
Changes or modifications not expressly
approved by the party responsible for
compliance could void your authority to operate
the equipment.
Avis de conformité à la FCC : Ce dispositif a
été testé et s’avère conforme à l’article 15 des
règlements de la Commission fédérale des
communications (FCC). Ce dispositif est
soumis aux conditions suivantes: 1) Ce
dispositif ne doit pas causer d’interférences
nuisibles et; 2) Il doit pouvoir supporter les
parasites qu’il reçoit, incluant les parasites
pouvant nuire à son fonctionnement.
Tout changement ou modification non approuvé
expressément par la partie responsable
pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
IC COMPLIANCE
This device contains license-exempt
transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic
Development Canada's license-exempt RSS(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. this device must accept any interference,
including interference that may cause
undesired operation of the device.
Changes or modifications not expressly
approved by the party responsible for
compliance could void your authority to operate
the equipment.
Cet appareil contient un ou des émetteurs/
récepteurs exemptés de licence qui sont
conformes aux normes RSS d'Innovation,
Sciences et Développement économique
Canada exemptées de licence. L'utilisation est
soumise aux deux conditions
suivantes :
1. Cet appareil ne doit pas causer
d'interférences.
2. Cet appareil doit accepter toute
interférence, y compris les interférences
susceptibles de provoquer un
fonctionnement non désiré de l'appareil.
Tout changement ou modification non approuvé
expressément par la partie responsable
pourrait annuler le droit à l’utilisateur de faire
fonctionner cet équipement.
ONE YEAR LIMITED WARRANTY
Important: SAVE YOUR RECEIPT! Evidence of
original purchase is required for warranty
service.
WARRANTOR: UNIDEN AMERICA CORPORATION
("Uniden")
ELEMENTS OF WARRANTY: Uniden warrants, for
one year, to the original retail owner, this Uniden
Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions
set out below.
WARRANTY DURATION: This warranty to the
original user shall terminate and be of no further
effect 12 months after the date of original retail sale.
The warranty is invalid if the Product is: (A) damaged
or not maintained as reasonable or necessary, (B)
modified, altered, or used as part of any conversion
kits, sub-assemblies, or any configurations not sold
by Uniden, (C) improperly installed, (D) serviced or
repaired by someone other than an authorized
Uniden service center for a defect or malfunction
covered by this warranty, (E) used in any conjunction
with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or
programmed by anyone other than as detailed by the
owners manual for this product.
STATEMENT OF REMEDY: In the event that the
product does not conform to this warranty at any time
while this warranty is in effect, warrantor will either, at
its option, repair or replace the defective unit and
return it to you without charge for parts, service, or
any other cost (except shipping and handling)
incurred by warrantor or its representatives in
connection with the performance of this warranty.
Warrantor, at its option, may replace the unit with a
new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS
THE SOLE AND ENTIRE WARRANTY PERTAINING
TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY
NATURE WHATSOEVER, WHETHER EXPRESS,
IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR
THE REIMBURSEMENT OVERPAYMENT OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
FCC RF EXPOSURE
WARNING! It is up to the user to properly
operate this radio transmitter to insure safe
operation. Please adhere to the following:
Do not use the radio with a damaged antenna.
If a damaged antenna comes into contact with
the skin, a minor burn may result. Please
contact your local dealer for a replacement
antenna.
Hand-Held Operation (Held-to-Face)
This device was evaluated for typical hand-held
(held-to-face) operations with a 1 inch spacing
from the front of the radio. For hand-held
operation, the radio should be held 1 inch from
the user's face in order to comply with FCC RF
exposure requirements.
Body-Worn Operation
This device was evaluated for body-worn
operations with the supplied belt-clip accessory.
(All necessary accessories are included in the
package; any additional or optional accessories
are not required for compliance with the
guidelines.) Third party accessories (unless
approved by the manufacturer) should be
avoided as these might not comply with FCC
RF exposure guidelines.
For body-worn operation, this device has been
tested and meets the Industry Canada RF
exposure guidelines when used with Uniden
accessories supplied or designated for this
product. Use of other accessories may not
ensure compliance with Industry Canada RF
exposure guidelines.
Fonctionnement de l’appareil, lorsque porté sur
le corps. Cet appareil a été testé et s’est avéré
conforme aux normes d’Industrie Canada et
approuvé pour le port sur le corps à l’aide des
accessoires Uniden inclus et conçus pour cet
appareil. L’utilisation d'accessoires ne
respectant pas les exigences d'exposition RF
d’Industrie Canada doit être évitée.
FCC PART 15/IC COMPLIANCE
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
© 2019 Uniden America Corporation Issue 5, June 2019
All rights reserved Printed in China
Some states do not allow this exclusion or limitation of
incidental or consequential damages so the above limitation
or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal
rights, and you may also have other rights which vary from
state to state. This warranty is void outside the United States
of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF
WARRANTY: If, after following the instructions in the
owners manual you are certain that the Product is defective,
pack the Product carefully (preferably in its original
packaging). The Product should include all parts and
accessories originally packaged with the Product. Include
evidence of original purchase and a note describing the
defect that has caused you to return it.The Product should be
shipped freight prepaid, by traceable means, to warrantor:
Uniden America Corporation
C/O Saddle Creek
743 Henrietta Creek Road, Suite 100
Roanoke, TX 76262
(800) 297-1023, 8 a.m. to 4:30 p.m., Central, Monday
through Friday
  • Page 1 1
  • Page 2 2

Uniden GMR2035-2 Le manuel du propriétaire

Catégorie
Radios bidirectionnelles
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues