Murata LBEE5HY1MW Guide d'installation

LBEE5HY1MW
Murata
Marque
Murata
Modèle
LBEE5HY1MW
Taper
Guide d'installation
1 / 9
LBEE5HY1MW Installation Manual
FCC ID of this product is as follows.
FCC ID: VPYLBEE5HY1MW
IC No. of this product is as follows.
IC: 772C-LBEE5HY1MW
Contents
1. Land Pattern (Recommended)
2. PIN Layout
3. Antenna
4. Supply Voltage and Operating Temperature
5. Theory of Operation-Channel List
6. Theory of Output Power List
2 / 9
1. Land Pattern (Recommended)
Unit : mm
3 / 9
2. PIN Layout
4 / 9
3. Antenna
■Please perform the antenna design that followed the specifications of the antenna.
■About the signal line between an antenna and a module
It is a 50-ohm line design.
Fine tuning of return loss etc. can be performed using a matching network.
However, it is required to check "Class1 change" and "Class2 change" which the authorities define then.
The concrete contents of a check are the following three points.
1) It is the same type as the antenna type of antenna specifications.
2) An antenna gain is lower than a gain given in antenna specifications.
3) The emission level is not getting worse.
■50-ohm line(microstrip line length)
Antenna
Antenna type
Loop antenna
50-ohm feed line length
We test it at 0mm as a representative
5 / 9
Recommended antenna design
This Antenna Specification is based on Keyence's requirement..
Model name LBEE5HY1MW
• Antenna Model Name : ANT16244DT
• Antenna type : Loop antenna
• Antenna manufacture : TDK Corporation
• Antenna gain : +2.1 dBi @2442MHz
+3.5 dBi @5150MHz
• Frequency : 2400-2483.5MHz, 5150-5850MHz
6 / 9
Recommended antenna characteristics
7 / 9
4. Supply Voltage
Parameter
Min.
Typ.
Max.
Unit
Operating Temperature*1
-30
25
+85
deg.C
Supply Voltage
3.2
3.3
4.8
V
1.62
-
3.63
V
*1: Surface temperature of the shield case
Functionality is guaranteed but specifications require derating at extreme temperatures
*2: VIO don’t influence the RF characteristic. Tolerance of 1.8V and 3.3V is ±10%.
5. Theory of Operation-Channel List
Theory of Operation-Software Security and Channel List
Frequency of operation
Scan
Ad-hoc mode
2.4GHz
11b/g/n (HT20)
2412-2462MHz
Active
Yes
BT
2402-2480MHz
N/A
N/A
W52
11a/n ((V)HT20)
5180-5240MHz
Active
Yes
W53
11a/n ((V)HT20)
5260-5320MHz
Passive
No
* This specification is limited to use in the above frequency bands and modes.
Notes: End users cannot modify the software because F/W & driver are installed in device.
8 / 9
6. Theory of Output Power List
This specification is limited to use with the following output power settings.
Limited output power setting. [dBm]
➢ 2.4GHz WLAN
Mode
Rate
1ch
2ch
3ch
4ch
5ch
6ch
7ch
8ch
9ch
10ch
11ch
IEEE
802.11b
1M
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
2M
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
5.5M
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
11M
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
14.0
IEEE
802.11g
6M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
9M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
12M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
18M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
24M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
36M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
48M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
54M
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
IEEE
802.11n
MCS0
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
MCS1
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
MCS2
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
MCS3
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
MCS4
10.0
10.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
10.0
10.0
MCS5
10.0
10.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
10.0
10.0
MCS6
10.0
10.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
10.0
10.0
MCS7
10.0
10.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
10.0
10.0
➢ 5GHz WLAN
Mode
Rate
36ch
40ch
44ch
48ch
52ch
56ch
60ch
64ch
IEEE
802.11a
6M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
9M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
12M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
18M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
24M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
36M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
48M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
54M
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
IEEE
802.11n
(HT20)
MCS0
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS1
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS2
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS3
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS4
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS5
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS6
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
MCS7
10.0
10.0
11.0
11.0
11.0
11.0
10.0
10.0
9 / 9
LBEE5HY1MW User Manual for FCC
■Regarding FCC modular approval of LBEE5HY1MW
Model Name: LBEE5HY1MW
FCC ID: VPYLBEE5HY1MW
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
● The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: VPYLBEE5HY1MW
or
Contains FCC ID: VPYLBEE5HY1MW
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
*If it cannot be described on the host product, it must be listed on both the host product manual and on
the host product package or removable label.
10 / 9
●The following statements must be described on the user manual of the host device of this module;
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the MAC, through
the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the
MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then
turns off at the end of the packet. Therefore, the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other words, this device automatically discontinue
transmission in case of either absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
●When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment
and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and
operated keeping the radiator at least 20cm or more away from person’s body.
●When installing it in a portable equipment. Please describe the following warning to the manual.
The available scientific evidence does not show that any health problems are associated with using low
power wireless devices. There is no proof, however, that these low power wireless devices are absolutely
safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range
while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure
of low-level RF that does not produce heating effects causes no known adverse health effects. Many
studies of low-level RF exposures have not found any biological effects. Some studies have suggested
that some biological effects might occur, but such findings have not been confirmed by additional
research. LBEE5HY1MW has been tested and found to comply with FCC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth
V5.0(BDR/EDR/LE)).
Class II permissive change application is necessary using the SAR report. Please contact Murata.
11 / 9
Note)
Portable equipment: Equipment for which the spaces between human body and antenna are used within
20cm.
Mobile equipment: Equipment used at position in which the spaces between human body and antenna
exceeded 20cm.
12 / 9
LBEE5HY1MW User Manual for ISED
PMN: LBEE5HY1MW
HVIN: LBEE5HY1MW
IC Number: 772C-LBEE5HY1MW
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
● The following information must be indicated on the host device of this module.
Contains IC: 772C-LBEE5HY1MW
●The following statements must be described on the user manual of the host device of this module;
This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts
de licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User's
manual.
●In case of the final product which can be carried around to outdoor.
The following indication is necessary to the final product.
When the AP function is used in W52;
At the time of a channel setting of W52, please indicate “for indoor use only”. During connecting, please
show the channel number which connects.
13 / 9
And please indicate that the end user may find out "for indoor use only channel".
When the STA function is used in channel 52, 54, 58, at the time of the channel 52 or 54 or 58 setting,
please indicate “for indoor use only channel”.
During connecting, please show the channel number which connects.
And please indicate that the end user may find out "for indoor use only channel".
If the antenna of the end product is removed, please describe the follow warning on the manual of the
end product which contains this module.
This radio transmitter (IC Number: 772C-LBEE5HY1MW) identify the device by certification number or
model number if Category II) has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain indicated. Antenna types not included in this list, having
a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
: 2.4GHz Loop Gain: +2.1 dBi
: 5GHz Loop Gain: +3.5 dBi
Le présent émetteur radio (IC Number: 772C-LBEE5HY1MW) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les
types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.
Type d’antenne
: 2.4GHz Loop Gain: +2.1 dBi
: 5GHz Loop Gain: +3.5 dBi
●If the final product use the following frequency, please note that there is a limit.
For indoor use only (5150-5250MHz band and channel 52, 54, 58)
Pour usage intérieur seulement (5150-5250MHz band and channel 52, 54, 58)
14 / 9
●The following statements must be described on the user manual of the host device of this module;
Data transmission is always initiated by software, which is the passed down through the MAC, through
the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the
MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then
turns off at the end of the packet. Therefore, the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other words, this device automatically discontinue
transmission in case of either absence of information to transmit or operational failure.
La transmission des données est toujours initiée par le logiciel, puis les données sont transmises par
l'intermédiaire du MAC, par la bande de base numérique et analogique et, enfin, à la puce RF. Plusieurs
paquets spéciaux sont initiés par le MAC. Ce sont les seuls moyens pour qu'une partie de la bande de
base numérique active l'émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence,
l'émetteur reste uniquement activé lors de la transmission d'un des paquets susmentionnés. En d'autres
termes, ce dispositif interrompt automatiquement toute transmission en cas d'absence d'information à
transmettre ou de défaillance.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User's
manual.
●When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and
meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and
operated keeping the radiator at least 20cm or more away from person’s body.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF)
CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus
entre le radiateur et le corps humain.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Murata LBEE5HY1MW Guide d'installation

LBEE5HY1MW
Murata
Marque
Murata
Modèle
LBEE5HY1MW
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents