User Manual
Since this module is not sold to general end users directly, there is no user manual of
module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification
(installation procedure).
The following information must be indicated on the host device of this module;
[for FCC]
Contains FCC ID:
2AU3BU9W
34
This device complies with
p
art 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in
the user’s manual and also either describe on the device packaging or on a removable label
attached on the device.
[for ISED(IC)]
Contains IC:
25625
-
U9W
34
The following statements must be described on the user manual of the host device of this
module;
[for FCC]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines.
To comply with FCC RF exposure compliance requirements, this grant is applicable
to only Mobile Configurations. The antennas used for this transmitter must be
installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or
transmitter.
[for ISED(IC)]
This device contains licence-exempt transmitters/receivers that comply with
Innovation, Science and Economic Development Canada’s license-exempt RSS
standards. Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’ émetterur/récepteur exempt de licence contenu dans le present appareil est
conforme aus CNR d’Innovation, Science et Développement économique Canada
applicables aux apparerils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
for
indoor
use
only
(5150
-
5250MHz)
Pour usage
intérieur seulement
(5150
-
5250MHz)
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the ISED radio frequency (RF)
Exposure rules. To comply with FCC RF exposure compliance requirements, this
grant is applicable to only Mobile Configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé
et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps
humain (a I’exception des extremites : mains, poignets, pieds et chevilles).
[for FCC]
Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down
through the MAC, through the digital and analog baseband, and finally to the RF
chip. Several special packets are initiated by the MAC. These are the only ways the
digital baseband portion will turn on the RF transmitter, which it then turns off at
the end of the packet. Therefore, the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other words, this device
automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
[for ISED(IC)]
Data transmission is always initiated by software, which is the passed down through
the MAC, through the digital and analog baseband, and finally to the RF chip.
Several special packets are initiated by the MAC. These are the only ways the digital
baseband portion will turn on the RF transmitter, which it then turns off at the end of
the packet. Therefore, the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other words, this device
automatically discontinue transmission in case of either absence of information to
transmit or operational failure.
La transmission des données est toujours initiée par le logiciel, puis les données
sont transmises par l'intermédiaire du MAC, par la bande de base numérique et
analogique et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le
MAC. Ce sont les seuls moyens pour qu'une partie de la bande de base numérique
active l'émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence,
l'émetteur reste uniquement activé lors de la transmission d'un des paquets
susmentionnés. En d'autres termes, ce dispositif interrompt automatiquement toute
transmission en cas d'absence d'information à transmettre ou de défaillance.
[§15.105 Information to the user]
For a Class B digital device or peripheral, the instructions furnished the user shall
include the following or similar statement, placed in a prominent location in the text
of the manual.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Compliance with KDB996369 D03 OEM Manual
1. List of applicable FCC rules
WiFi 2412-2462MHz FCC Part 15.247 Max output power 15.92dBm
WiFi 5180-5240MHz; 5745-5825MHz FCC Part 15.407 Max output power 13.65dBm
2. Summarize the specific operational use conditions
When use this modular transmitter, please do not change the antenna and antenna
gain, the power setting and country code can not be changed.
The Antenna type is monopole antenna and 2T2R
2400-2483.5MHz Peak Gain: ANT A: 2.55dBi; ANT B: 0.94dBi;
U-NII-1 Band (5150-5250MHz) Peak Gain: ANT A: 1.90dBi; ANT B: 0.8dBi;
U-NII-3 Band (5725-5850MHz) Peak Gain: ANT A: -0.04dBi; ANT B: -3.17dBi.
3. Limited module procedure
Not applicable
4. Trace Antenna designs
Not applicable
5. RF exposure considerations
This modular transmitter should be used in the mobile conditions and 20cm from a
person’s body, the host product manufacture should be put those information in the
end-product manual to the end users. If RF exposure statement and use conditions
are not provided, then the host product manufacture is required to take responsibility
of the module through a change in FCC ID(new application)
6. Antenna
The Antenna type is Planar antenna and 2T2R.
2400-2483.5MHz Peak Gain: ANT A: 2.55dBi; ANT B: 0.94dBi;
U-NII-1 Band (5150-5250MHz) Peak Gain: ANT A: 1.90dBi; ANT B: 0.8dBi;
U-NII-3 Band (5725-5850MHz) Peak Gain: ANT A: -0.04dBi; ANT B: -3.17dBi.
7. Label and compliance information
We Had put the FCCID: 2AU3BU9W34 on the modular transmitter and put the
compliance information in this modular use manual, the host device manufacture
need to provide a physical or e-label stating“ contains FCCID: 2AU3BU9W34” with
their finished product and the compliance information should be attached in the
end-product manual.
8. Information on test modes and additional testing requirement
When this modular transmitter installed in a host product, then can use a 4 pin-USB
extend cable, the 4 pin port connect with the modular and USB port connect with a
test computer which installed the test software “MP tool” then can use the software
control the modular working at test mode, select the transmit mode, channel and
power setting.
9. Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part
15C and FCC Part 15E) listed on the grant, and that the host product manufacture is
responsible for compliance to any other FCC rules that apply to the host not covered
by the modular transmitter grant of certificates
-
1
-
2
-
3
-
4
-
5
-
6
-
7
dans d''autres langues
- English: Funai U9W34 User manual
Autres documents
-
Atel FJ1510MA Manuel utilisateur
-
Murata LBEE5HY1MW Guide d'installation
-
Silex technology SX-USBAC Manuel utilisateur
-
Hui Zhou Gaoshengda Technology WT5YM2511 Wi-Fi+BT Module Mode d'emploi
-
GSD WXT2F Manuel utilisateur
-
GSD WXT2AM2101 WIFI+BT Module IEEE Manuel utilisateur
-
GSD WC5EM2601F Dual Band WiFi Module Manuel utilisateur
-
GSD WC5F Manuel utilisateur
-
GSD WXT5BM2511 Le manuel du propriétaire
-
GSD DT3AR1501 Manuel utilisateur
