Easy-Kleen 8549263 Le manuel du propriétaire

Marque: Easy-Kleen

Modèle: 8549263

Taper: Le manuel du propriétaire

Ce manuel convient également à

8662785

1-800-315-5533 • service@easykleen.com • www.easykleen.com

Owners Manual

Commercial and Industrial Hot Water Gas

and Diesel Driven, Oil Fired

Oil Fired Gas & Diesel • Rev. 4/7/2016

Easy-Kleen Pressure Systems

1-800-315-5533

This manual contains operational information that is specific for commercial and industrial

(Bull Moose and Grizzly) hot water, gas and diesel driven, oil fired machines.

Read the following instructions carefully before attempting to assemble,

install, operate, or service this pressure washer. Failure to comply with these

instructions could result in personal injury and/or property damage.

Table of Contents

IMPORTANT SAFETY INFORMATION ............................................................................................................. 3

SPECIFICATIONS ............................................................................................................................................ 7

INTRODUCTION ............................................................................................................................................. 9

OPERATING INSTRUCTIONS ........................................................................................................................ 10

CHEMICAL APPLICATION ............................................................................................................................. 12

WINTER PUMP/ COIL PROTECTION ............................................................................................................ 13

GENERAL MAINTENANCE ............................................................................................................................ 13

MAINTENANCE CHECKLIST .......................................................................................................................... 15

GLOSSARY OF TERMS .................................................................................................................................. 17

COMPONENT IDENTIFICATION ................................................................................................................... 18

QUICK DIAGNOSTICS AND SOLUTIONS GUIDE ............................................................................................ 25

WIRING DIAGRAMS ..................................................................................................................................... 27

MANUFACTURER’S WARRANTY .................................................................................................................. 31

SERVICE MANUAL........................................................................................................................................ 32

Oil Fired Gas & Diesel • Rev. 4/7/2016

IMPORTANT SAFETY INFORMATION

The safe operation of our pressure washing systems is the FIRST priority of Easy-Kleen. This

will only be achieved by following the operation and maintenance instructions as explained in

this manual and all other enclosed manuals.

This manual contains essential information regarding the safety hazards, operations, and

maintenance associated with this machine. The manual should always remain with the machine,

including if it is resold.

ALL CAUTIONS AND SAFETY WARNINGS MUST BE FOLLOWED TO AVOID

INJURY OR DAMAGE TO EQUIPMENT.

THIS EQUIPMENT IS TO BE USED ONLY BY TRAINED OPERATORS AND MUST

ALWAYS BE ATTENDED DURING OPERATION.

WARNING: To reduce the risk of injury,

read operating instructions carefully

before using.

WARNING: Use protective

eyewear and clothing when

operating equipment in

order to avoid personal

injuries.

1. Read the instructions in this manual carefully before attempting to assemble,

install, operate or service this pressure washer. Failure to comply with the

instructions could result in personal injury and/or property damage.

WARNING: This

machine exceeds

85db. Appropriate

ear protection must

be worn.

WARNING: Flammable

liquids can create fumes

which can ignite, causing

property damage or severe

injury.

WARNING: Risk of

explosion. Operate only

where open flame

or torch is permitted.

2. Be thoroughly familiar with all controls and know how to stop the machine in

the event of an emergency.

Oil Fired Gas & Diesel • Rev. 4/7/2016

WARNING: Risk of fire. Do not

add fuel when operating machine.

3. Never use gasoline, crankcase draining, or waste oil in your burner fuel

tank. Never run pump dry or let the pump run with the trigger gun released

for more than 2 minutes. The minimum clearance to any combustible material

is 12 inches.

WARNING: Keep water spray

away from electrical wiring.

4. All electrically powered equipment must be grounded at all times to prevent

fatal electric shots. Do not spray water on or near electrical components. Do

not touch electrical components while standing in water or when hands are

wet. Always make sure machine is disconnected from power source before

servicing.

WARNING: Risk of asphyxiation.

Use this product only in a well

ventilated area.

5. Use equipment in a well-ventilated area to avoid carbon monoxide poisoning

or death. This machine must never be connected to a Type B gas vent.

WARNING: Risk of injection or

severe injury to persons. Keep

clear of nozzle spray.

6. High pressure spray can cause serious injuries. Never point pressurized

spray at any person or animal. Handle the spray assembly with care.

WARNING: Risk of

injury. Hot surfaces

can cause burns.

WARNING: Hot discharge

fluid. Do not touch or

direct discharge stream

at persons.

Oil Fired Gas & Diesel • Rev. 4/7/2016

7. Hold firmly to the gun and wand during start up and operation of the

machine. Do not attempt to make adjustments while the trigger gun is in

operation.

8. Make sure all quick coupler fittings are properly secured before operating

pressure washer.

WARNING: Risk of injury

from falls when using ladder.

9. Do not overreach or stand on anything unstable. Keep a good balance and

make sure to keep a steady footing at all times.

WARNING: Protect from freezing.

WARNING: Trigger gun kicks

back. Hold with both hands.

10. It is important to keep your machine from freezing in order to keep it in its

best working condition. Failure to protect your machine from freezing may

cause damage to the machine and personal injuries may occur as a result.

11. For machines with a 12 V burner: Disconnect battery ground terminal

before servicing.

12. Protect high pressure hoses from sharp objects and vehicles. Inspect

condition of hoses prior to use, or serious injury could occur.

13. Do not pass acids or other caustic or abrasive fluids through the pump.

WARNING: Risk of Injury

RISK OF INJURY

Oil Fired Gas & Diesel • Rev. 4/7/2016

14. Never run pump dry of water or oil or or let the pump run with the trigger gun

released for more than 2 minutes.

15. Do not attempt to operate this machine if fatigued or under the influence of alcohol,

prescription medications, or drugs.

16. Some of the maintenance procedures involved in this machine require a certified

technician (these steps are indicated throughout this manual). Do not attempt to perform

these repairs if you are not qualified.

If you need further explanation of any of the information in this manual, suspend any

activity involving the equipment and call our toll free number for assistance,

1-800-315-5533.

Oil Fired Gas & Diesel • Rev. 4/7/2016

SPECIFICATIONS

Commercial Hot Water Gas - Oil Fired

MODEL

GPM

PSI

BURNER OIL

PRESSURE (PSI)

BTU

HP/ ENGINE

DRIVE

ELECTRIC

START

BURNER

EZO2703G

2700

130

300,000

6.5 KOHLER

DIRECT

120V

EZO4035G-K-GP-R

3.5

4000

130

350,000

14 KOHLER

DIRECT

120V

EZO4035G-H-GP-R

3.5

4000

130

350,000

13 HONDA

DIRECT

120V

EZO4035G-K-GP-120

3.5

4000

130

350,000

14 KOHLER

DIRECT

YES

120V

EZO4035G-H-GP-120

3.5

4000

130

350,000

13 HONDA

DIRECT

YES

120V

EZO4035G-L-GP-12

3.5

4000

130

350,000

15 LIFAN

DIRECT

YES

12V

EZO4035G-K-GP-12

3.5

4000

130

350,000

14 KOHLER

DIRECT

YES

12V

EZO4035G-H-GP-12

3.5

4000

130

350,000

13 HONDA

DIRECT

YES

12V

EZO3504G-K

3500

130

400,000

14 KOHLER

GEARBOX

YES

12V

EZO3504G-H

3000

130

400,000

13 HONDA

GEARBOX

YES

12V

Commercial Hot Water Diesel - Oil Fired

MODEL

GPM

PSI

BURNER OIL

PRESSURE (PSI)

BTU

HP/ ENGINE

DRIVE

ELECTRIC

START

BURNER

EZO4035D-K-GP-12

3.5

4000

130

350,000

9.8 KOHLER

DIRECT

YES

12V

EZO3504D-K

3500

130

400,000

9.8 KOHLER

GEARBOX

YES

12V

*-GG – has a generator

*-ST – steam kit

Industrial Hot Water Gasoline – Oil Fired (Grizzly Series)

MODEL*

GPM

PSI

BURNER OIL

PRESSSURE (PSI)

BTU

HP/ENGINE

DRIVE

EZO3004G

3000

160

400,000

13 HONDA

BELT

EZO3504BG

3500

160

400,000

14 KOHLER

GEARBOX

EZO3504G

3500

160

400,000

14 KOHLER

BELT

EZO3505G

3500

130

500,000

20 HONDA

BELT

EZO3506G

3500

145

600,000

25 KOHLER

BELT

EZO3008G

3000

155

800,000

25 KOHLER

BELT

EZO3010G

3000

130

1,000,000

38 KOHLER

BELT

EZO3708G

3700

130

800,000

38 KOHLER

BELT

EZO5005G

5000

130

500,000

25 KOHLER

BELT

EZO6004G

6000

160

400,000

25 KOHLER

BELT

EZO6006G

6000

145

600,000

38 KOHLER

BELT

EZO7004G

7000

160

400,000

25 KOHLER

BELT

Oil Fired Gas & Diesel • Rev. 4/7/2016

Industrial Hot Water Diesel – Oil Fired (Bull Moose Series)

MODEL

GPM

PSI

BURNER OIL

PRESSURE (PSI)

BTU

HP/ENGINE

DRIVE

EZO3204D

3200

160

400,000

9.8 KOHLER

BELT

EZO3506D

3500

145

600,000

26 KOHLER

BELT

EZO3508D

3500

130

800,000

26 KOHLER

BELT

EZO3010D

3000

130

1,000,000

26 KOHLER

BELT

EZO5005D

5000

130

500,000

26 KOHLER

BELT

EZO5010D

5000

130

1,000,000

58 KUBOTA

GEARBOX

EZO6004D

6000

160

400,000

26 KOHLER

BELT

EZO7004D

7000

160

400,000

26 KOHLER

BELT

EZO8008D

8000

130

1,000,000

58 KUBOTA

GEARBOX

Oil Fired Gas & Diesel • Rev. 4/7/2016

INTRODUCTION

Thank you for selecting a quality Easy-Kleen product. We are pleased to have you included

among the many satisfied owners of Easy-Kleen cleaning machines. Years of engineering

have gone into the development of these fine products and only top quality components and

materials are used throughout. Each machine is carefully tested and inspected before leaving

our plant to ensure years of dependable performance.

To continue to receive satisfactory performance, remembering that this machine represents a

substantial investment on your part, and if properly cared for and maintained it will return this

investment many times over. As with all mechanical equipment, your machine requires proper

operation and maintenance as outlined in this manual for maximum trouble free life.

This manual has been prepared under the direction of our engineering and service technicians.

Their experience in designing, manufacturing, installing and servicing our equipment from our

company’s inception is condensed in this manual. They know what information the end user

needs in order to get the optimum performance from their pressure washer. Please read

carefully.

This manual contains information that will be specific for your pressure washer, as well as

similar models.

Carefully review any additional manuals that have been included with your system and

follow ALL ADDITIONAL OPERATING INSTRUCTIONS AND SAFETY NOTICES.

They are specific for the quality components that have been used to manufacture your

machine and are an integral part of the operating and maintenance procedures.

The management & staff at Easy-Kleen are proud of the equipment that we design and

manufacture and we thank you for making us your # 1 choice in pressure washers. If you have

any questions please do not hesitate to call us, 1-800-315-5533.

Our goal is that you will be satisfied with the performance, quality, and service you receive from

Easy-Kleen and that if you need to replace this machine in years to come, you will give us the

opportunity to continue supplying equipment to your company.

PLEASE READ MANUALS CAREFULLY BEFORE USING MACHINE. EXAMINE

MACHINE AND CRATE CAREFULLY FOR SHIPPING DAMAGE OR MISSING

PARTS. REPORT PROMPTLY ANY SHORTAGES OR DAMAGE CLAIMS TO

FREIGHT CARRIER OR DEALER.

Oil Fired Gas & Diesel • Rev. 4/7/2016

OPERATING INSTRUCTIONS

1. Perform pre-start maintenance inspection on all applicable systems prior to operating the

machine. This is essential for the safe, effective and efficient operation. You will get optimum

performance from your system ONLY if these instructions and inspections are followed. Any

indication that the pressure washing system was not operated and maintained according to these

instructions may cancel the manufacturers’ warranty.

Location – Be sure to install in an area that has sufficient air ventilation to support combustion

of oil in burner.

Controls – Make sure all controls turned to the off position.

Pump – Oil level - Level the pressure washer. Be sure oil level in the pump is correct on dip

stick. If the level is low, add the correct oil to the proper level. USE ONLY SAE 30 W NON-

DETERGENT OIL OR HYDRAULIC 68. DO NOT OVER FILL.

Gas Engine - Gasoline level – The engine is a 4 cycle and uses regular octane, unleaded fuel.

DO NOT USE MIXED FUEL. Refer to the engine operation manual included with your

pressure-washing unit.

Gas Engine - Oil level – The engine is a 4 cycle and uses 10W30 detergent oil. Refer to

Glossary or engine manual.

Diesel Engine – Refer to engine operation manual included with your pressure washing unit for

oil and fuel recommendations.

Oil Fired Burner - Oil Tank Level – #2 Furnace oil is recommended for the burner oil tank, as

it burns cleaner and the burner requires less maintenance. Diesel fuel may be used as an

alternative. Do not overfill burner tank.

Visually inspect all electrical components to assure they are in good condition, showing

No signs of exposure, breakage or splicing.

Visually inspect all hoses, nozzles and guns to assure they are in good condition. If

replacements are necessary they must be rated to withstand the machines operating

pressure and temperatures.

2. Attach high-pressure hose to hot water outlet quick connector. Attach the other end of high

pressure hose (with quick coupler) to spray gun. Ensure that quick disconnect connections are

tightly locked together. Apply a sharp pull on hose to confirm they are secured.

Attach wand nozzle specific to task requirements (i.e. chemical or pressure wash).

[Quick Coupling Operation – Pull back sleeve end and insert male end into nozzle quick coupler,

release sleeve and confirm connection by pulling on the nozzle].

Oil Fired Gas & Diesel • Rev. 4/7/2016

3. Attach water source to water inlet located on pump. The water source must be attached with

a good quality standard garden type hose (1/2” minimum is required). Connect male fitting into

the female pump inlet fitting. Make sure that the inlet screen/filter is intact and fitted correctly.

Turn on water source. WATER MUST BE IN SUFFICIENT SUPPLY, AND PRESSURE

MUST BE BETWEEN 20 –60 PSI TO ENSURE PROPER AND SAFE OPERATION. Specific

attention should be given if using a well water supply. Ensure water is flowing from end nozzle

with the trigger gun pulled. Deplete system of all air.

4. Start Gas/Diesel Engine

Refer to instructions in engine manual. MAKE SURE THAT THE ENGINE EXHAUST IS NOT

FACING ANY FLAMMABLE MATERIALS. Adjust burner thermostat to desired temperature,

then turn BURNER switch to ‘ON’.

5. Burner operation

Be sure water is flowing through water heater coil before turning on BURNER switch. Turn

thermostat to desired temperature. Burner will ignite and remain in operation as long as there is

sufficient water flow to satisfy the pressure switch and temperature control.

IF YOU EXPERIENCE IGNITION FAILURE, DO NOT ATTEMPT TO RESTART

BURNER! EXCESS FUEL AND VAPORS MAY HAVE ACCUMULATED AND THE

CHAMBER MAY BE HOT. THE UNIT MUST COOL DOWN BEFORE RESTART CAN

BE ATTEMPTED.

Warning: Condensation on Coil

When cold water is being pumped through the heater coil and the burner is firing, condensation

may form at times on the coil and drip down into the burner compartment. This can be

particularly noticeable on cold, humid days giving the false appearance of a leaking coil. A

leaking coil or system will be evident if the pump keeps cycling with the trigger released. The

pump head pressure should read ‘0’.

Electrically Operated Burners – These models generate 12V from the gasoline engine and

provide the necessary power for the burner. IF YOU REQUIRE UPGRADES OR

MODIFICATIONS TO YOUR EXISTING ELECTRICAL SYSTEM IN ORDER TO

OPERATE YOUR PRESSURE WASHER, THEY MUST BE PERFORMED BY A LICENSED

ELECTRICIAN AND BE COMPLETED IN ACCORDANCE TO ALL APPLICABLE CODES

IN YOUR AREA OF OPERATION. The power supply must be adequate for your specific unit.

Make sure to verify the data plate for your machine’s specific requirements (i.e. voltage,

amperage, etc.).

6. Pressure adjustment - The pressure regulator (unloader) is located on the pump (see

diagram). It controls the pressure being generated by the pressure washer. This regulator may be

adjusted to the desired pressure by turning the adjustment knob. Turning the adjustment knob

clockwise will increase the pressure. NEVER OPERATE SYSTEM AT A HIGHER PSI

THAN THE MAXIMUM RATING. This machine has been adjusted to operate at a specific

maximum pressure as per the machine specifications. Pressure may be reduced for lighter use by

turning the Pressure Regulator/Unloader counter clockwise. If continuing to turn the unloader

clockwise does not increase the pressure, then this implies the maximum has been reached for

Oil Fired Gas & Diesel • Rev. 4/7/2016

the system. Any further turning of the unloader will cause the pressure to spike when the wand

trigger is released, resulting in possible damage to the machine. To avoid this effect, loosen the

unloader (counter-clockwise) until the pressure just starts to drop (see pump head pressure

gauge) and until it no longer exceeds the maximum pressure rating for the machine.

7. You are now ready to start the cleaning operation - Pull trigger on the pressure wand

assembly to start cleaning. To stop the pressurized water, release the trigger. DO NOT

LEAVE UNIT RUNNING WHEN NOT IN USE.

8. To stop Burner operation – Turn BURNER switch to ‘PUMP’ (or to ‘OFF’ for Auto start

stop models) and run pump for two minutes with trigger gun pulled to allow coil to cool down.

After cooling period is complete, turn off main power to motor by turning BURNER switch to

‘OFF’ (turn PUMP switch to ‘OFF’ if equipped with auto start stop). Squeeze and release the

trigger for the second time in order to relieve the pump system of pressure.

9. Prior to storage – Inspect pressure washer for any damage or required maintenance. If your

machine is to be exposed to cold weather, please refer to winter pump/coil instructions found in

this manual. If possible, do not allow unit to remain outside in the elements.

10. Warning – If unit is left running while not in use, pump damage may occur. Do not leave

unit running while not in use!

11. Battery Specifications for electric start systems only – Rating: 165CCA, 190 CA or better,

dimensions: 8” x 5” x 6” (applies to commercial units).

CHEMICAL APPLICATION

Downstream Chemical Injection: Standard (Direct Drive Units)

High Pressure Soap (Optional Feature)

NOTE: Do not remove back flow preventer as chemical may flow back into potable water

source. For standard chemical injection, ensure the black nozzle is properly fitted at the

end of the wand. The chemical injector will not function if this nozzle is not fitted.

1. Chemical preparation – Select detergent/chemical that best suits your cleaning task. Prepare

dilution according to the manufacturer’s instructions. The volume of chemical being used may be

adjusted at valve located on the chemical injector. Note: for EK Pumps, the volume is preset and

cannot be adjusted.

2. Insert the intake hose, located on the chemical injector at the pump, into the chemical being

used.

Oil Fired Gas & Diesel • Rev. 4/7/2016

3. Fit black nozzle on the standard wand, or for the dual wand, turn adjustment knob on, and

adjust for required flow rate. For high pressure soap systems, the black nozzle is not needed; use

one of the other wand nozzles.

4. To apply chemical, engage trigger on pressure wand assembly. Turn chemical injector’s nipple

to adjust flow. For the high pressure soap systems, open ball valve and engage trigger.

5. Chemical can now be applied through pressure wand assembly. It will take 5 – 15 seconds for

chemical to travel to spray nozzle. The volume of chemical being used may be adjusted at the

chemical injector.

6. For best results apply chemical from bottom to top, and allow for proper penetration time prior

to rinsing. Do not allow chemical to dry. Rinse from bottom to top and then top to bottom.

WINTER PUMP/ COIL PROTECTION

The following procedure MUST be used when the pressure washing

unit is stored at temperatures below freezing.

1. All water must be drained or blown (via compressed air) from system. Connect a short piece

of male fitted ½” garden type hose on to the female inlet on the pump.

2. Place the open end of the hose into a wide mouthed container of full strength, winter rated,

vehicle windshield washing fluid or Anti-Freeze, RATED FOR MINIMUM -40°C.

3. Connect the pressure wand assembly.

4. Start the engine and engage the trigger on the pressure gun. Operate the system until the fluid

runs the same color as the windshield washing fluid. Your machine is now prepared for storage.

5. Disconnect fluid supply, blow out with compressed air, and cap end.

GENERAL MAINTENANCE

Burner Maintenance

NOTE: Repair of the burner is to be done by authorized and trained burner professionals

only.

The oil filter cartridge should be replaced every year to prevent fuel contamination and plugging

of fuel pump and nozzle of oi burner. The nozzle should also be replaced at least once every year

or twice if used daily and if poor combustion begins to occur. See the included burner manual for

more information on burner.

Oil Fired Gas & Diesel • Rev. 4/7/2016

Final adjustments to burner include fuel pressure adjustment for controlling water temperature

(tighten fuel pressure adjustment screw slightly to increase desired output temperature) and air

band adjustment for combustion efficiency. A combustion test kit should be used for these final

adjustments. Check SPECIFICATIONS chart (page 7) for the burner oil pressure corresponding

to your model and be sure not to exceed this pressure. See included burner manual for more

information and a parts break down of the burner.

If the burner floods with oil: run machine with heat on until all excess oil is burned off (this

can take up to a couple of hours). If excess oil is not properly dealt with, the ceramic casing can

absorb excess oil, causing a fire hazard. DO NOT LEAVE MACHINE UNATTENDED WHILE

MACHINE IS FLOODED.

General Maintenance and Care

If the water heater is likely to be exposed to freezing weather then it should be winterized

according to the winter pump/coil protection procedure in the previous section. Alternate

methods may not completely protect the components. Damage from freezing is not a warrantable

item.

Water Condition

Use a softener on your water system if local water is known to be high in mineral content. The

advantages of soft water are very beneficial: prevents scale buildup in heater coil, cleans better

with considerably less detergent, prevents streaking on painted surfaces and glass when rinsing.

Descaling Heater Coil Procedure

NOTE: Descaling of the heater coil is to be done by authorized and trained burner

professionals only.

The best way to acidize the coil is with a circulation pump capable of handling acids.

1. Fill a plastic container with a suitable acid diluted with water to desired strength.

2. Connect discharge from the circulating pump to the hot water outlet on the water heater with a

suitable hose. Connect the inlet of the circulating pump to the acid container with suction hose

from the pump module and use it as a return hose to the acid container. As acid dissolves the

scale it becomes neutralized, so about every five minutes add more acid to the container until all

the scale has been removed from the coil. Flush out coil thoroughly with water after descaling.

Oil Fired Gas & Diesel • Rev. 4/7/2016

MAINTENANCE CHECKLIST

Maintenance for Pump

Daily 1. Check oil for proper level and adjust accordingly.

2. Examine the quality of the oil.

3. Check pump for oil and/or water leaks.

4. Inspect and clean inlet filters.

Weekly

1. Examine all fittings, components, hoses, connections, and nozzles for damages, loose

parts, or leaks. – Replace accordingly—

Recommendation for Oil Changes and Component Replacement

1. Change the oil in the pump after the first 50 hours and every 500 hours after the initial

oil change. Use SAE 30 W Non-Detergent for GP Pumps and Hydraulic 68 for EK

Pumps.

2. Change all other components on the pump as needed.

Maintenance for Gasoline Engine

Daily 1. Check oil for proper level and adjust accordingly.

2. Examine the quality of the oil

3. Examine the air cleaner element

Weekly

1. Examine engine components for damages, loose parts, or leaks.

Oil Fired Gas & Diesel • Rev. 4/7/2016

Recommended Schedule for Oil Changes and Component Replacements

1. Change engine oil after first 5 hours and every 100 hours after the initial oil change.

Use 10w-30 engine oil.

2. Replace Spark Plug every 100 hours.

3. Change air cleaner element every 100 hours.

4. Check fuel filters every 300 hours.

5. Change all other components on engine as needed.

Oil Fired Gas & Diesel • Rev. 4/7/2016

GLOSSARY OF TERMS

PSI – Pounds per square inch. Pressure washers are designed and rated to operate at a specific

PSI. Operating at pressures exceeding the maximum rating could result in damage to the unit

and/or SEVERE PERSONAL INJURY.

GPM – Gallons per minute. The orifice on the pressure wand assembly has been selected to

deliver up to the maximum GPM for your machine.

PRESSURE WAND ASSEMBLY – This refers to the gun, wand, and nozzle.

PUMP – The pump moves the water through the system and delivers it to the pressure wand

assembly.

UNLOADER VALVE – Is a valve located at the head of the pump for unloading water back

into the bypass when the trigger gun is shut off. It also reduces the load on pump when gun is

off.

OIL, PUMP – The oil used within the pump to lubricate its operation. Important to use only

SAE 30 W Non Detergent (GP Pump) or Hydraulic 68 (EK Pump) in the pump (see diagram).

OIL, GASOLINE ENGINE – Gasoline Engines need appropriate lubricant. Use 10W30

detergent oil.

BURNER – The burner heats the water in hot water pressure washers. It is located under the coil

and may be powered by furnace oil or diesel fuel.

BACK FLOW PREVENTER – Device to prevent flow backwards into potable water supply.

MAXIMUM WORKING PRESSURE The water heater coils are designed to operate safely at

normal working pressure. Each machine is equipped with a safety pressure relief valve which

prevents over pressurization of the high pressure system. It is an important safety device and

must not be tampered with in any way.

TEMPERATURE CONTROL- The water heater is equipped with a temperature control which

shuts down the burner in the event of excessive outlet temperature caused by insufficient water

flow through the heater coil. Do not set thermostat above 195°F

PRESSURE SWITCH - A high pressure switch is used to control the burner. It is part of the

burner control system (see diagram).

FLOW SWITCH – A flow switch is installed on the outlet of the high pressure pump and will

shut off the pump and motor in the absence of water flow as well as turning it back on when flow

is detected (by squeezing the trigger).

Oil Fired Gas & Diesel • Rev. 4/7/2016

COMPONENT IDENTIFICATION

Commercial Model:

10 Gallon Poly Fuel Tank

Burner Switch and

Thermostat

Gasoline Engine

Coil Skin

Oil Fired Gas & Diesel • Rev. 4/7/2016

Direct Driven Pump Assembly:

Chemical

Injector

Water Inlet

Unloader

Burner Control

Pressure Switch

Safety Relief Valve

Temperature

probe

Hot Water Outlet

Quick Connector

Water Pump

Oil Fired Gas & Diesel • Rev. 4/7/2016

Bull Moose Series Industrial Model:

*Model shown with optional steam kit.

Hot Water Outlet

Flue Outlet

Water Pump

Instrument Panel

Water and

Steam Inlet

Coil Skin

Diesel Engine

12V Battery Box

20 Gallon Poly Fuel Tanks

(For Burner and Engine)

Temperature Probe

Flow Switch

La page charge ...

Easy-Kleen 8549263 Le manuel du propriétaire

Marque: Easy-Kleen

Modèle: 8549263

Taper: Le manuel du propriétaire

Ce manuel convient également à

8662785

Télécharger le PDF

rapport

dans d''autres langues

English: Easy-Kleen 8549263 Owner's manual

Easy-Kleen 8549263 Le manuel du propriétaire

Ce manuel convient également à

Easy-Kleen 8549263 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents