__________
__________
©2018 La-Z-Boy Incorporated DOC007911 Rev. 07/18
power recliner
Sillón reclinable
fauteuil inclinable ÉlectroPlus
Important Safety Instructions..........................................4-5
Platinum Luxury-Lift®Assembly Instructions.......................6-7
Platinum Luxury-Lift®Battery Backup Assembly Instructions....8
1PL Platinum Luxury-Lift®Operating Instructions.............9 -13
1PM Platinum Luxury-Lift®with 6-Motor Massage and Heat
Operating Instructions...........................................................14 -19
1PH Platinum Luxury-Lift®with Adjustable Headrest and
Lumbar Operating Instructions...........................................20-25
Platinum Luxury-Lift®Additional Operating Features................26
Platinum Luxury-Lift®Troubleshooting...............................27-28
1PH Platinum Luxury-Lift®Hand Wand Removal Instructions.........30
1PH Platinum Luxury-Lift®Hand Wand Installation Instructions.......31
Platinum Luxury-Lift®Back Removal and Assembly Instructions 32-35
Furniture Moving and Placement Guide.....................................36
IMPORTANT
Read the safety and other instructions before
using your Platinum Luxury-Lift®Power Recliner.
Keep this manual for future reference.
3
2
Congratulations!
You are now the proud owner of a
stat e-of-the-art Platinum Luxury-Lift®
Power Recliner by La-Z-Boy.
You have just selected one of the
finest quality upholstered products
produced in the furniture industry,
backed by over 90 years of quality
manufacturing experience.
La-Z-Boy is proud of our
designs and craftsmanship and
knows you will feel the same as
you enjoy your new furniture’s
comfort and style.
Table of Contents
Disclaimer: The information and products featured in this manual may be
somewhat different from the product you purchased. La-Z-Boy reserves the right
to make substitutions that are equal in quality and performance.
5
4
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
When assembling, do not plug in until directed in Operating Instructions.
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
When assembling, do not plug in until directed in Operating Instructions.
-- To reduce the risk of electric shock, serious injury or death:
• Do not let children play on or near the chair when in use. Serious injury or death could occur if head
or body parts are under the chair when the chair is in motion.
• Disconnect the electrical plug from outlet before cleaning, moving, servicing or when not in use for
an extended period of time.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle the plug or
remote control with wet hands.
• To prevent suffocation keep plastic bags away from children.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
-- To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas
and thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery.
For your safety, always use a properly installed smoke detector with working batteries.
• Closely supervise children and disabled persons using this product.
• Remove hand wand when not in use, and store out of reach of children.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.
Move the unit into or out of the reclining position slowly, making sure that no children or pets are
in close proximity
• This product has many moving parts, serious injury can occur if not used properly. Keep hands, fingers
and body parts away from the mechanism. To reduce the risk of head entrapment and other injuries,
keep children and pets away from openings and moving parts in and around furniture.
• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.
• Do not stand, sit, or place extra weight on the arms, back or open legrest.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• This product is intended for indoor residential use only.
• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance
to allow the legrest to fully extend without rubbing or interference.
• Check the condition of the power supplies, electrical cords, plugs, and connectors often. Keep the
power supplies and electrical cords away from heat sources. Never operate the unit with a damaged
power supply, electrical cord, plug or connector. Contact your La-Z-Boy®dealer for service.
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand has been dropped
in water or any liquid. Contact your La-Z-Boy®dealer for service.
• This product is not intended for use as a health care device. Some medications and physical limitations
may impair your ability to operate this product in a safe manner. Consult your physician if you are
taking prescribed or over the counter medication, or if you have physical limitations.
• Users of medical devices should contact their health care provider before using this product. Do not
use this product if you have poor circulation, are immobile, or cannot sense heat, except as directed
by your health care provider.
DANGER
WARNING
Save These Instructions Save These Instructions
• Unit is designed to ease exit from the chair. Take care to not slip out of chair when chair is in motion.
• Do not use this product where aerosol (spray) products are being used or where oxygen
is being administered.
• In the event of a power failure, the battery backup provided may not lift the user to a fully raised
position. To ensure lift functionality during a power outage, a battery backup system must be
purchased separately. Contact your La-Z-Boy®dealer for more information. Replace the power
supply batteries every six months and after each power failure use.
• Do not operate the unit until the back is installed and locked.
• Before moving a Platinum Series chair, disconnect electrical plug from the wall outlet. Moving
the chair requires two people, one on each side of the chair lifting the frame near the base; refer
to the Operating Instructions online. Only move the product by the lower arm frame, never by the
legrest or reclining back.
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are inside.
Contact your La-Z-Boy®dealer for service.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the
floor. Do not place cord under carpet or in a location where it could become worn.
• Do not use pillow, blanket, or other cover between occupant and chair surface when heat is engaged.
• Always unplug the power cord before connecting or disconnecting the hand wand.
• Unplug the power cord immediately if you detect strange odors or fumes coming from the chair.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power
plug and pull it out.
• Burns may result from improper use and care of internal heating pads. To avoid risk of burns, do
not use pins, do not allow heating pad area to become wet, and do not remove upholstery cover.
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350 pounds.
Do not operate the chair with more than one occupant in or on any part of the chair.
• If you give this product to someone else, include this Operating Instructions manual.
• The back of the unit must be lifted for assembly and disassembly. Please seek assistance if
you are unable to lift at least 45 pounds without strain.
– To reduce the risk of product damage:
• To prevent damage to the power supply, do not plug in until instructed.
• Gently press the buttons during operation and avoid hitting the buttons with pointed
or hard objects.
• Never operate the unit except when it is on its base in the upright position.
• After 2 minutes of continuous operation of the 4LP, 1PL, 1PM, 1PH and 1HM chairs, allow the
lift and recline features to rest for 18 minutes.
NOTICE
Tie Securing Power Supply and Power Cord
FIGURE 1
Platinum Luxury-Lift®Assembly Instructions Platinum Luxury-Lift®Assembly Instructions
1. Choose a location for the lift chair that is close to an electrical outlet.
2. Starting with the chair removed from the carton and all packing material removed, carefully turn
the chair forward to rest on the front of the arms and top of the back.
3. The power supply connector is tucked behind the upholstered tailgate (FIGURE 1). Remove the
power supply connector from the tailgate by gently pulling it out.
4. Locate and cut the cable tie holding the boxed power supply and power cord to the underside
of the chair (FIGURE 1). Set the box and power cord aside.
5. Carefully return the chair to its upright position.
6. The hand wand is tucked behind the seat chaise pad for shipping (FIGURE 2). Gently pull the
hand wand out from between the back and seat, remove the plastic bag and lay hand wand
on seat (FIGURE 3).
7
6
– To reduce the risk of product damage:
• Do not plug the power supply in until instructed.
NOTICE
7. Make the power supply connections.
• Remove power supply from box and unwind cord.
•Align the power supply connector to the power supply connector from behind the chair
and push the connectors together until they lock (FIGURE 4).
•Connect the 120 volt power cord to the power supply. Align the 120 volt power cord connector
to the power supply and push together until fully seated (FIGURE 4). Do not plug in until
instructed in the Operating Instructions.
8. Proceed to the Battery Backup Assembly Instructions.
Upholstered Tailgate
Power Supply Connector
Tucked Behind Tailgate
FIGURE 2
Hand
Wand
FIGURE 3
FIGURE 4
120 Volt Power
Cord Connection
Power Supply
Connection
(Assembly Instructions Continued)
9
8
1PL Platinum Luxury-Lift®
Operating Instructions
Platinum Luxury-Lift®
Battery Backup Assembly Instructions
– To reduce the risk of serious injury:
• In the event of a power failure, the battery backup provided may not lift the user to a fully
raised position. To ensure lift functionality during a power outage, a battery backup system
must be purchased separately. Contact your La-Z-Boy®dealer for more information.
Replace the power supply batteries every six months and after each power failure use.
WARNING
Battery Backup Assembly Instructions
The performance of the built-in battery backup cannot be guaranteed. If you require continuing use
during a power outage, you should purchase a separate battery backup system. Contact your
La-Z-Boy®dealer for more information.
When operating on battery backup, the only functions the system allows are:
(1) Return the chair to home from any reclined position.
(2) Lift and lower the chair.
(3) Decrease intensity of adjustable lumbar.
To reduce battery consumption, the recline, massage, heat, headrest and increase lumbar intensity
features are blocked and unavailable.
The operating speed is reduced when operating on battery backup.
Always maintain constant, even pressure on the button or toggle when operating on battery backup
to reduce energy consumption.
The built-in battery backup is located in the power supply and uses two 9-volt alkaline batteries
(not included).
1. Unplug the power supply from the electrical outlet and disconnect the power supply
connection at the base of the chair.
2. The battery compartment is located on the side of the power supply. Slide the battery cover
up to access the battery compartment.
3. Place the connection caps over the battery terminals on each battery. Place the batteries in the
compartment, taking care not to damage any wires.
4. Slide the battery cover over the compartment.
5. Proceed to the Operating Instructions.
Platinum Luxury-Lift®Power Supply Specifications:
Input: 120–240V~,50/60Hz,1.5A
Output: 29V, 2.0A
Power Supply
(2) 9-Volt Alkaline Batteries
Battery
Cover
– To reduce the risk of serious injury or death:
• Do not let children play on or near the chair when in use. Serious injury or death could
occur if head or body parts are under the chair when the chair is in motion.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle
the plug or remote control with wet hands.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
DANGER
Getting Started
Connect the power supply connector to the connector at the base of the lift chair. Connect
the 120 volt power cord to the power supply. Plug the power supply directly into a wall outlet.
Platinum Luxury-Lift®Operation
The 1PL offers multiple modes of operation. The large, round LIFT and RECLINE button on the front
of the hand wand AND the toggle on the back of the hand wand provide coordinated movements.
The LIFT and RECLINE button and back toggle will operate all functions of the chair in one fluid
movement from sitting, reclining and legrest extension, back to the upright position and standing.
Individual movement of the back and legrest can be achieved by pressing the BACK button to recline
and return the back of the unit, and by pressing the LEGREST button to extend and return the legrest.
– To reduce the risk of serious injury:
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350
pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close
the legrest.
• Unit is designed to ease exit from the chair. Take care to not slip out of chair when
chair is in motion.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
– To reduce the risk of product damage:
• After 2 minutes of continuous operation of the 4LP, 1PL, 1PM, 1PH and 1HM chairs,
allow the lift and recline features to rest for 18 minutes.
NOTICE
(1PL Operating Instructions Continued)
11
10
1PL Platinum Luxury-Lift®
Operating Instructions
To recline the chair:
There are multiple modes of operation to recline the chair. The back and legrest recline movements
are both synchronous and independent. The back and legrest recline are programmed to move
together using the front, large round LIFT and RECLINE button at the top of the hand wand, or
the toggle on the back of the hand wand. The back and legrest recline are programmed to
move independently using the front, oblong BACK and LEGREST buttons. The independent
operation allows you to recline the back without raising the legrest, raise the legrest without
reclining the back, or make individual adjustments to the back and legrest recline, which are
outside the synchronous movement.
1. With the chair in the seated position, to recline the back and raise the legrest at the same
time, press and hold the front, large round RECLINE button, or press the back toggle up and
hold. To recline only the back or raise only the legrest, press and hold down on the right side
of the appropriate front, oblong BACK or LEGREST button. Release the button or toggle when
you are in a comfortable position.
2. Make adjustments to the back and legrest recline as preferred.
3. To return the chair to the upright, seated (home) position, press and hold down on the front,
large round LIFT button, or press and hold the back toggle down. Release the button or toggle
when you reach the upright, seated (home) position. There is a two second delay that occurs
when the chair arrives at its seated, home position; the chair starts the lift function after the
delay when the front, large round button or back toggle is pressed and held. Additionally, you
may press and hold down on left side of the front, oblong BACK button, followed by the
LEGREST button, releasing the button when the movement reaches its end of travel and stops.
To stand up from the chair:
There are multiple modes of operation for the lift feature. Both the front, large round LIFT button
at the top and the back toggle provide a coordinated movement of the lift function. The back must
be fully upright and the legrest fully closed for the lift feature to function.
1. Firmly position your feet on the floor to maintain balance and prevent sliding or falling. Press
down on the front LIFT button and hold, or press the back toggle down and hold, to raise the
chair to the standing position.
2. Release the button or toggle when the chair reaches a height that enables you to comfortably
stand. Carefully exit the chair.
3. Return the chair to the seated (home) position if you will be away from the chair for an
extended period of time. Press down on the front RECLINE button and hold, or press the back
toggle up and hold to lower the chair. Release the button or toggle when the chair is in its
seated (home) position.
NOTE: The system includes a built-in two second delay that occurs when the chair arrives at its
seated, home position. The chair starts the reclining function immediately following the two second delay.
Platinum Luxury-Lift®Operation Continued
To sit down in the chair:
1. Stand beside the chair and press down on the front LIFT button and hold, or press the back
toggle down and hold. Release the button or toggle when the chair reaches a comfortable height
to sit against, depending on your personal needs and preference.
2. Step back into the chair and sit in the center of the seat while keeping your feet firmly on the floor.
3. Press down on the front RECLINE button and hold, or press the back toggle up and hold to lower
the chair. Release the button or toggle when the chair reaches the seated, home position. There
is a two second delay that occurs when the chair arrives at its seated, home position; the chair
starts the recline function after the delay.
(Page intentionally left blank)
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
13
12
1PL Platinum Luxury-Lift®
Operating Instructions 1PL Platinum Luxury-Lift®
Operating Instructions
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
WARNING
Coordinated Lift
& Return Button
When seated, press and
hold down on the LIFT
button to raise the chair
to the standing position.
– OR –
When reclined, press and
hold down on the LIFT
button to return the back
to the upright position
and the legrest to the
closed position.
Release the button to stop
in any reclined position, or
when fully upright.
FRONT
Coordinated Lower
& Recline Button
When lifted, press and hold
down on the RECLINE
button to lower the chair
to the seated position.
– OR –
When seated, press and
hold down the RECLINE
button to recline the back
and raise the legrest.
Release the button to stop
in any reclined position, or
when fully reclined.
Toggle Down –
Coordinated Lift
& Return
When seated, press the
toggle down and hold to
raise the chair to the
standing position.
– OR –
When reclined, press the
toggle down and hold
to return the back to
the upright position and
the legrest to the closed
position.
Release the toggle to stop
in any reclined position, or
when fully upright.
BACK
Toggle Up –
Coordinated Lower
& Recline
When lifted, press the
toggle up and hold
to lower the chair to
the seated position.
– OR –
When seated, press the
toggle up and hold to
recline the back and raise
the legrest.
Release the toggle to stop
in any reclined position, or
when fully reclined.
Independent Back &
Legrest Recline Buttons
Press and hold down the
left side of the BACK
button to raise the back to
the upright position.
Release the button to stop
in any reclined position, or
when fully upright.
Press and hold down the
left side of the LEGREST
button to lower the legrest.
Release the button to stop
in any position, or when
fully closed.
Independent Back &
Legrest Recline Buttons
Press and hold down the
right side of the BACK
button to recline the back.
Release the button to stop
in any reclined position, or
when fully reclined.
Press and hold down the
right side of the LEGREST
button to raise the legrest.
Release the button to stop
in any raised position, or
when fully extended.
15
14
1PM Platinum Luxury-Lift®with
6-Motor Massage and Heat Operating Instructions
– To reduce the risk of serious injury or death:
• Do not let children play on or near the chair when in use. Serious injury or death could
occur if head or body parts are under the chair when the chair is in motion.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle
the plug or remote control with wet hands.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
DANGER
Getting Started
Connect the power supply connector to the connector at the base of the lift chair. Connect
the 120 volt power cord to the power supply. Plug the power supply directly into a wall outlet.
Platinum Luxury-Lift®with 6-Motor Massage and Heat Operation
The 1PM offers multiple modes of operation. The large, round LIFT and RECLINE button on the front
of the hand wand AND the toggle on the back of the hand wand provide coordinated movements.
The LIFT and RECLINE button and back toggle will operate all functions of the chair in one fluid
movement from sitting, reclining and legrest extension, back to the upright position and standing.
Individual movement of the back and legrest can be achieved by pressing the BACK button to recline
and return the back of the unit, and by pressing the LEGREST button to extend and return the legrest.
– To reduce the risk of serious injury:
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350
pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close
the legrest.
• Unit is designed to ease exit from the chair. Take care to not slip out of chair when
chair is in motion.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
– To reduce the risk of product damage:
• After 2 minutes of continuous operation of the 4LP, 1PL, 1PM, 1PH and 1HM chairs,
allow the lift and recline features to rest for 18 minutes.
NOTICE
To recline the chair:
As with the lift feature, there are multiple modes of operation to recline the chair. The back and
legrest recline movements are both synchronous and independent. The back and legrest recline
are programmed to move together using the front, large round LIFT and RECLINE button at the
top of the hand wand, or the toggle on the back of the hand wand. The back and legrest recline
are programmed to move independently using the front, oblong BACK and LEGREST buttons. The
independent operation allows you to recline the back without raising the legrest, raise the legrest
without reclining the back, or make individual adjustments to the back and legrest recline, which
are outside the synchronous movement.
1. With the chair in the seated position, to recline the back and raise the legrest at the same
time, press and hold the front, large round RECLINE button, or press the back toggle up and
hold. To recline only the back or raise only the legrest, press and hold down on the right side
of the appropriate front, oblong BACK or LEGREST button. Release the button or toggle when
you are in a comfortable position.
2. Make adjustments to the back and legrest recline as preferred.
3. To return the chair to the upright, seated (home) position, press and hold down on the front,
large round LIFT button, or press and hold the back toggle down. Release the button or toggle
when you reach the upright, seated (home) position. There is a two second delay that occurs
when the chair arrives at its seated, home position; the chair starts the lift function after the
delay when the front, large round button or back toggle is pressed and held. Additionally, you
may press and hold down on left side of the front, oblong BACK button, followed by the
LEGREST button, releasing the button when the movement reaches its end of travel and stops.
To stand up from the chair:
There are multiple modes of operation for the lift feature. Both the front, large round LIFT button
at the top and the back toggle provide a coordinated movement of the lift function. The back must
be fully upright and the legrest fully closed for the lift feature to function.
1. Firmly position your feet on the floor to maintain balance and prevent sliding or falling. Press
down on the front LIFT button and hold, or press the back toggle down and hold, to raise the
chair to the standing position.
2. Release the button or toggle when the chair reaches a height that enables you to comfortably
stand. Carefully exit the chair.
3. Return the chair to the seated (home) position if you will be away from the chair for an
extended period of time. Press down on the front RECLINE button and hold, or press the back
toggle up and hold to lower the chair. Release the button or toggle when the chair is in its
seated (home) position.
NOTE: The system includes a built-in two second delay that occurs when the chair arrives at its
seated, home position. The chair starts the reclining function immediately following the two second delay.
To sit down in the chair:
1. Stand beside the chair and press down on the front LIFT button and hold, or press the back
toggle down and hold. Release the button or toggle when the chair reaches a comfortable height
to sit against, depending on your personal needs and preference.
2. Step back into the chair and sit in the center of the seat while keeping your feet firmly
on the floor.
3. Press down on the front RECLINE button and hold, or press the back toggle up and hold to lower
the chair. Release the button or toggle when the chair reaches the seated, home position. There
is a two second delay that occurs when the chair arrives at its seated, home position; the chair
starts the recline function after the delay.
1PM Platinum Luxury-Lift®with
6-Motor Massage and Heat Operating Instructions
(1PM Operating Instructions Continued)
1PM Platinum Luxury-Lift®with
6-Motor Massage and Heat Operating Instructions
Platinum Luxury-Lift®with 6-Motor Massage and Heat Operation Continued
To use the massage and heat features:
The heat and massage functions are independent of each other, as are the back and seat heat.
The massage, back heat and seat heat can be operated individually or simultaneously.
The heat and massage features include an automatic timer to shut off the MASSAGE and HEAT
functions after approximately 15 minutes* of operation. You can restart the heat and massage
features for one additional 15 minute period of operation, but will need to give the system a rest
after two consecutive 15 minute periods of operation. Activated heat and massage functions are
temporarily suspended when either the LIFT or RECLINE motor is in use.
1. Press the left side of the HEAT button to activate the back heat. Press the right side of the
HEAT button to activate the seat heat.
•Press the button once for low heat, indicated by an amber LED.
•Press the button twice for high heat, indicated by a red LED.
•Press the button a third time to turn off the heat.
2. Press the left side of the MASSAGE button to activate the massage feature. Press the right
side of the MASSAGE button to set the intensity of the massage.
•Press the left side of the MASSAGE button once to turn on the massage feature.
- Press once for constant on mode, indicated by a green LED.
- Press twice for wave mode, indicated by an amber LED.
- Press three times for pulse mode, indicated by a red LED.
- Press a fourth time to turn off the massage; the LED turns off when the feature is off.
•Press the right side of the MASSAGE button to set the intensity of the massage mode.
- Press once for low intensity, indicated by a green LED.
- Press twice for medium intensity, indicated by an amber LED.
- Press three times for high intensity, indicated by a red LED.
* The heat and massage features will run for up to two 15 minute cycles. After two continuous
cycles, the heat and massage will shut down.
•Allowing the system to cool down for 7½ minutes will provide one 15 minute heat and
massage cycle.
•Allowing the system to cool down for 15 minutes will provide two 15 minute heat and
massage cycles.
(1PM Operating Instructions Continued)
17
16
(Page intentionally left blank)
19
18
1PM Platinum Luxury-Lift®with
6-Motor Massage and Heat Operating Instructions 1PM Platinum Luxury-Lift®with
6-Motor Massage and Heat Operating Instructions
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
WARNING
Coordinated Lift
& Return Button
When seated, press and hold
down on the LIFT button to raise
the chair to the standing position.
– OR –
When reclined, press and hold
down on the LIFT button to
return the back to the upright
position and the legrest to the
closed position.
Release the button to stop in
any reclined position, or when
fully upright.
FRONT Coordinated Lower
& Recline Button
When lifted, press and hold down
on the RECLINE button to lower
the chair to the seated position.
– OR –
When seated, press and hold down
the RECLINE button to recline the
back and raise the legrest.
Release the button to stop
in any reclined position, or when
fully reclined.
Toggle Down –
Coordinated Lift
& Return
When seated, press the
toggle down and hold to
raise the chair to the
standing position.
– OR –
When reclined, press the
toggle down and hold
to return the back to
the upright position and
the legrest to the closed
position.
Release the toggle to stop
in any reclined position, or
when fully upright.
BACK
Toggle Up –
Coordinated Lower
& Recline
When lifted, press the
toggle up and hold
to lower the chair to the
seated position.
– OR –
When seated, press the
toggle up and hold to
recline the back and raise
the legrest.
Release the toggle to stop
in any reclined position, or
when fully reclined.
Independent Back &
Legrest Recline Buttons
Press and hold down the left side
of the BACK button to raise the
back to the upright position.
Release the button to stop
in any reclined position,
or when fully upright.
Press and hold down the left
side of the LEGREST button
to lower the legrest.
Release the button to stop
in any position, or when
fully closed.
Independent Back &
Legrest Recline Buttons
Press and hold down the right
side of the BACK button to
recline the back.
Release the button to stop in
any reclined position, or when
fully reclined.
Press and hold down the right
side of the LEGREST button to
raise the legrest.
Release the button to stop in
any raised position, or when
fully extended.
Press the left side of the HEAT
button to activate the back heat.
Press once for low heat (amber LED)
and twice for high heat (red LED).
Press a third time to turn the
back heat off (unlit).
Press the left side of the MASSAGE
button to activate the back and seat
massage. Press once for constant
massage (green LED), twice for wave
massage (amber LED), three times for
pulse massage (red LED) and four times
to turn the massage off (unlit).
Back Heat
Intensity
LED
(amber
shown)
Massage
Program
LED
(green
shown)
Press the right side of the
HEAT button to activate the
seat heat. Press once for low
heat (amber LED) and twice for
high heat (red LED). Press
again to turn the seat heat off
(unlit).
Press the right side of the
MASSAGE button to set the
massage intensity. Press once
for low intensity (green LED),
twice for medium intensity
(amber LED) and three times
for high intensity (red LED).
Massage
Intensity
LED
(amber
shown)
Seat
Heat
Intensity
LED
(red
shown)
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
1PH Platinum Luxury-Lift®with
Adjustable Headrest & Lumbar Operating Instructions 1PH Platinum Luxury-Lift®with
Adjustable Headrest & Lumbar Operating Instructions
21
20
– To reduce the risk of serious injury or death:
• Do not let children play on or near the chair when in use. Serious injury or death could
occur if head or body parts are under the chair when the chair is in motion.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle
the plug or remote control with wet hands.
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
• Keep cord out of reach of small children, and do not use where it may be a trip hazard.
DANGER
Getting Started
Connect the power supply connector to the connector at the base of the lift chair. Connect
the 120 volt power cord to the power supply. Plug the power supply directly into a wall outlet.
Platinum Luxury-Lift®with Adjustable Headrest and Lumbar Operation
The 1PH offers multiple modes of operation. The large, round LIFT and RECLINE button on the front
of the hand wand AND the toggle on the back of the hand wand provide coordinated movements.
The LIFT and RECLINE button and back toggle will operate all functions of the chair in one fluid
movement from sitting, reclining and legrest extension, back to the upright position and standing.
Individual movement of the back and legrest can be achieved by pressing the BACK button to recline
and return the back of the unit, and by pressing the LEGREST button to extend and return the legrest.
Customized comfort is achieved by pressing the HEADREST button to set the angle of the headrest tilt
and the LUMBAR button to set the intensity of the lumbar.
– To reduce the risk of serious injury:
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350
pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back
of the unit. Move the unit into or out of the reclining position slowly, making sure that
no children or pets are in close proximity.
• To safely exit the unit and prevent a tripping hazard, bring the back upright and close
the legrest.
• Unit is designed to ease exit from the chair. Take care to not slip out of chair when
chair is in motion.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
– To reduce the risk of product damage:
• After 2 minutes of continuous operation of the 4LP, 1PL, 1PM, 1PH and 1HM chairs,
allow the lift and recline features to rest for 18 minutes.
NOTICE
To recline the chair:
As with the lift feature, there are multiple modes of operation to recline the chair. The back and
legrest recline movements are both synchronous and independent. The back and legrest recline
are programmed to move together using the front, large round LIFT and RECLINE button at the
top of the hand wand, or the toggle on the back of the hand wand. The back and legrest recline
are programmed to move independently using the front, oblong BACK and LEGREST buttons. The
independent operation allows you to recline the back without raising the legrest, raise the legrest
without reclining the back, or make individual adjustments to the back and legrest recline, which
are outside the synchronous movement.
1. With the chair in the seated position, to recline the back and raise the legrest at the same
time, press and hold the front, large round RECLINE button, or press the back toggle up and
hold. To recline only the back or raise only the legrest, press and hold down on the right side
of the appropriate front, oblong BACK or LEGREST button. Release the button or toggle when
you are in a comfortable position.
2. Make adjustments to the back and legrest recline as preferred.
3. To return the chair to the upright, seated (home) position, press and hold down on the front,
large round LIFT button, or press and hold the back toggle down. Release the button or toggle
when you reach the upright, seated (home) position. There is a two second delay that occurs
when the chair arrives at its seated, home position; the chair starts the lift function after the
delay when the front, large round button or back toggle is pressed and held. Additionally, you
may press and hold down on left side of the front, oblong BACK button, followed by the
LEGREST button, releasing the button when the movement reaches its end of travel and stops.
To stand up from the chair:
There are multiple modes of operation for the lift feature. Both the front, large round LIFT button
at the top and the back toggle provide a coordinated movement of the lift function. The back must
be fully upright and the legrest fully closed for the lift feature to function.
1. Firmly position your feet on the floor to maintain balance and prevent sliding or falling. Press
down on the front LIFT button and hold, or press the back toggle down and hold, to raise the
chair to the standing position.
2. Release the button or toggle when the chair reaches a height that enables you to comfortably
stand. Carefully exit the chair.
3. Return the chair to the seated (home) position if you will be away from the chair for an
extended period of time. Press down on the front RECLINE button and hold, or press the back
toggle up and hold to lower the chair. Release the button or toggle when the chair is in its
seated (home) position.
NOTE: The system includes a built-in two second delay that occurs when the chair arrives at its
seated, home position. The chair starts the reclining function immediately following the two second delay.
To sit down in the chair:
1. Stand beside the chair and press down on the front LIFT button and hold, or press the back
toggle down and hold. Release the button or toggle when the chair reaches a comfortable height
to sit against, depending on your personal needs and preference.
2. Step back into the chair and sit in the center of the seat while keeping your feet firmly
on the floor.
3. Press down on the front RECLINE button and hold, or press the back toggle up and hold to lower
the chair. Release the button or toggle when the chair reaches the seated, home position. There
is a two second delay that occurs when the chair arrives at its seated, home position; the chair
starts the recline function after the delay.
23
22
(Page intentionally left blank)
1PH Platinum Luxury-Lift®with
Adjustable Headrest & Lumbar Operating Instructions
1. Press and hold down the right side of the HEADREST button to tilt the headrest forward.
Release the button when the desired level of tilt is achieved or when the headrest is fully
forward. Press and hold down the left side of the HEADREST button to return the headrest.
Release the button when the desired level of tilt is achieved or when the headrest is fully retracted.
2. Press and hold down the right side of the LUMBAR button to increase the intensity of the
lumbar. Release the button when the desired level of support is achieved or when the lumbar
is fully extended. Press and hold down the left side of the LUMBAR button to decrease the
intensity and return the lumbar. Release the button when the desired level of support is
achieved or when the lumbar is fully retracted.
With the exception of retracting the lumbar, these features are blocked and temporarily
suspended when the chair is in LIFT mode. Additionally, the headrest automatically retracts
and returns to the home position as soon as the chair starts in lift mode. The only feature
that is available for adjustment while the chair is in lift mode is the retracting of the lumbar.
Refer to the Battery Backup Assembly instructions for details about the functionality when
operating on battery backup. Full functionality is only available when the chair is powered
by utility power and not in lift mode.
Avoid pressing the HEADREST and LUMBAR buttons at the same time to reduce the chance
for an over-current condition.
To use the headrest and lumbar features:
The adjustable headrest and lumbar functions are independent of each other and provide the
means to customize the comfort level for individual users.
1PH Platinum Luxury-Lift®with
Adjustable Headrest & Lumbar Operating Instructions 1PH Platinum Luxury-Lift®with
Adjustable Headrest & Lumbar Operating Instructions
25
24
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
WARNING
Coordinated Lift
& Return Button
When seated, press and hold
down on the LIFT button to raise
the chair to the standing position.
– OR –
When reclined, press and hold
down on the LIFT button to
return the back to the upright
position and the legrest to the
closed position.
Release the button to stop in
any reclined position, or when
fully upright.
FRONT Coordinated Lower
& Recline Button
When lifted, press and hold down
on the RECLINE button to lower
the chair to the seated position.
– OR –
When seated, press and hold down
the RECLINE button to recline the
back and raise the legrest.
Release the button to stop
in any reclined position, or when
fully reclined.
Toggle Down –
Coordinated Lift
& Return
When seated, press the
toggle down and hold to
raise the chair to the
standing position.
– OR –
When reclined, press the
toggle down and hold
to return the back to
the upright position and
the legrest to the closed
position.
Release the toggle to stop
in any reclined position, or
when fully upright.
BACK
Toggle Up –
Coordinated Lower
& Recline
When lifted, press the
toggle up and hold
to lower the chair to the
seated position.
– OR –
When seated, press the
toggle up and hold to
recline the back and raise
the legrest.
Release the toggle to stop
in any reclined position, or
when fully reclined.
Independent Back &
Legrest Recline Buttons
Press and hold down the left side
of the BACK button to raise the
back to the upright position.
Release the button to stop
in any reclined position,
or when fully upright.
Press and hold down the left
side of the LEGREST button
to lower the legrest.
Release the button to stop
in any position, or when
fully closed.
Independent Back &
Legrest Recline Buttons
Press and hold down the right
side of the BACK button to
recline the back.
Release the button to stop in
any reclined position, or when
fully reclined.
Press and hold down the right
side of the LEGREST button to
raise the legrest.
Release the button to stop in
any raised position, or when
fully extended.
Press and hold down the left
side of the HEADREST button to
return the headrest. Release the
button to stop the headrest in any
position or when fully retracted.
Press and hold down the left side
of the LUMBAR button to decrease
the lumbar intensity. Release the
button to stop the lumbar in any
position or when fully retracted.
Press and hold down the right
side of the HEADREST button
to tilt the headrest forward.
Release the button to stop the
headrest in any position or
when fully forward.
Press and hold down the right
side of the LUMBAR button to
increase the lumbar intensity.
Release the button to stop the
lumbar in any position or when
fully extended.
– To reduce the risk of serious injury:
• Do not use unit if power control is damaged or wet. Do not use unit if the hand wand
has been dropped in water or any liquid. Contact your La-Z-Boy®dealer for service.
• Remove hand wand when not in use, and store out of reach of children.
WARNING
Platinum Luxury-Lift®
Additional Operating Features
Power Supply Over-Current Protection
The Platinum series lift chairs are equipped with over-current protection. This feature prevents damage
to the motors and electronics if there is an overload, short circuit or ground fault. Should the system
detect an over-current, the system shuts down and the chair stops functioning.
If the over-current protection is activated, stop pressing the button or toggle in use. The system should
reset automatically. If you believe the chair is not being overloaded, or experiencing a short circuit or
ground fault, you may restart the function of the chair after the button or toggle has been released.
Should the over-current protection trip repeatedly, refer to the Troubleshooting section in this manual.
Additionally, the power supply includes a green LED status light to indicate power is being supplied
to the system. If the light is not illuminated, no power is being supplied to the system. Refer to the
Troubleshooting section in this manual if the power supply is plugged in, but the green light is
not illuminated.
– To reduce the risk of serious injury:
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are
inside. Contact your La-Z-Boy®dealer for service.
• Check the condition of the power supplies, electrical cords, plugs, and connectors
monthly. Keep the power supplies and electrical cords away from heat sources.
Never operate the unit with a damaged power supply, electrical cord, plug, or connector.
Contact your La-Z-Boy®dealer for service.
• The 1PL, 1PM and 1PH lift chairs are intended for a single occupant, not exceeding 350
pounds. Do not operate the chair with more than one occupant in or on any part of the chair.
WARNING
Troubleshooting for Legrest Operation
If the legrest stops moving while closing, and all other functionality of the lift chair is operating,
the legrest may have encountered an obstruction.
1. Check to make sure there are no obstructions. Lift and hold the legrest up, look for obstructions
and remove them.
2. The legrest uses spring tension to close, and will close quickly when the obstruction is
removed and the legrest is released. Release the legrest slowly to prevent it from slamming shut.
If there are no obstructions and the legrest still does not close properly, contact your La-Z-Boy®
dealer for service.
Troubleshooting for Lift and Recline Operation
If the lift or recline features do not work, check the following:
1. Make sure the 120 volt power cord is plugged into an electrical outlet.
2. Check the power supply to make sure the green LED power indicator light is on.
3. Make sure the electrical outlet is working. For example, make sure there are no blown
fuses or tripped circuit breakers.
4. Make sure all the connections are secure; refer to the Assembly Instructions.
5. Make sure the electrical cords are not crimped or pinched. Make sure the electric
cord or plug is not damaged.
6. Make sure the operating capacity has not been exceeded and there is only one
occupant in the chair; refer to the Operating Instructions.
Platinum Luxury-Lift®
Troubleshooting
(Troubleshooting Continued)
27
26
Troubleshooting for Massage and Heat Operation
If the massage or heat features do not work, check the following:
1. Make sure the time limit of two consecutive 15-minute periods of operation (30 minutes total)
has not been exceeded. To check this, wait three minutes and restart the massage or heat.
It the feature starts working, the automatic timer has shut off the features for the rest period,
and will need to continue to rest.
2. Make sure the 120 volt power cord is plugged into an electrical outlet.
3. Check the power supply to make sure the green LED power indicator light is on.
4. Make sure the electrical outlet is working. For example, make sure there are no blown fuses
or tripped circuit breakers.
5. Make sure all the connectors are secure; refer to the Assembly Instructions.
6. Make sure the electrical cords are not crimped or pinched. Make sure the electric cord or
plug is not damaged.
Troubleshooting for Headrest and Lumbar Operation
If the adjustable headrest or lumbar features do not work, check the following:
1. Make sure the 120 volt power cord is plugged into an electrical outlet.
2. Check the power supply to make sure the green LED power indicator light is on.
3. Make sure the electrical outlet is working. For example, make sure there are no blown fuses
or tripped circuit breakers.
4. Make sure all the connectors are secure; refer to the Assembly Instructions.
5. Make sure the electrical cords are not crimped or pinched. Make sure the electric cord or
plug is not damaged.
If the Platinum Luxury-Lift®still does not operate properly, contact your La-Z-Boy®dealer for
service. Except for the replacement of the power supply, never attempt to make any repairs
or adjustments yourself.
Power Supply Replacement
If the power supply must be replaced:
1. Unplug the power supply from the electrical outlet.
2. Disconnect the 120 volt power cord from the power supply, and disconnect the power supply
from the power supply connector at the base of the unit. Refer to the Assembly Instructions.
3. Connect the new power supply to the power supply connector at the base of the unit; align
the connectors and push together until locked. Connect the 120 volt power cord to the new
power supply; align the connector to the power supply and push together until fully seated.
Refer to the Assembly Instructions.
4. Proceed to the Battery Backup Assembly Instructions.
Platinum Luxury-Lift®
Troubleshooting
29
28
(Page intentionally left blank)
31
30
1PH Platinum Luxury-Lift®Hand Wand
Installation Instructions
1PH Platinum Luxury-Lift®Hand Wand
Removal Instructions
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Unplug the power cord before connecting or disconnecting the hand wand.
WARNING
1. Unplug the 120 volt power cord from the electrical outlet.
2. Stand behind the chair and disconnect the power supply from the chair. Locate the connection
behind the chair, push down the locking tab and pull the connectors apart (FIGURE 1).
3. From the front of the chair, locate the hand wand connection on the seat. Open the locking
cover and gently pull the connection apart to separate the hand wand from the body (FIGURE 2).
Store the hand wand out of reach of children.
FIGURE 2
FIGURE 1
Power Supply Connection Hand Wand Connection with Locking Cover
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Unplug the power cord before connecting or disconnecting the hand wand.
WARNING
1. Unplug the 120 volt power cord from the electrical outlet.
2. Stand behind the chair and disconnect the power supply from the chair. Locate the connection
behind the chair, push down the locking tab and pull the connectors apart (FIGURE 1).
3. From the front of the chair, locate the hand wand body connector near the back of the seat.
Align the arrow on the hand wand connector to the arrow on the body connector and push
together until fully seated, THEN back the connection out slightly (FIGURE 2). Close the locking
cover to secure the connection. (FIGURE 3).
4. Connect the power supply to the chair.
FIGURE 2
FIGURE 1
FIGURE 3
Hand Wand Connection
secured with Locking
Cover closed
– To reduce the risk of electric shock, serious injury
or death:
• Plug directly into a wall outlet. Do not use an extension cord, adapter or surge protector.
DANGER
5. Plug the 120 volt power cord directly into the electrical outlet.
Fully seat the
Connectors,
then back out
slightly before
closing the
Locking Cover
Power Supply Connection
Platinum Luxury-Lift®
Back Removal Instructions
– To reduce the risk of injury:
• The back of the unit must be lifted for assembly and disassembly. Please seek
assistance if you are unable to lift at least 45 pounds without strain.
• Do not operate the unit until the back is installed and locked.
WARNING
1. Unplug the 120 volt power cord from the electrical outlet.
2. Disconnect the power supply from the chair. Locate the connection behind the chair, push
down the locking tab and pull the connectors apart (FIGURE 1).
3. For a 1PL or 1PH chair, proceed to step 4. For a 1PM style chair with massage and heat features,
disconnect the electrical connections between the back and body.
•Carefully rotate the unit forward onto a clean protective surface to rest on its front side.
•Disconnect the massage and heat features:
- Disconnect the heat feature. Locate the connection with a red connector and a black
connector; the red 2-pin connector routes from the back and the black 2-pin connector
routes from the body. Push down the locking tab and pull out on the connectors to
disconnect the heat (FIGURE 2).
- Disconnect the massage feature. Locate the connection with two green connectors; one
green 6-pin connector routes from the back and the other from the body. Push down the
locking tab and pull out on the connectors to disconnect the massage (FIGURE 2).
•Carefully rotate the unit back to its upright position, sitting on its legs.
4. Loosen the outside back cover. Reach behind the body rear rail and locate the fastening tape
securing the outside back cover to the backside of the frame (FIGURE 3). Gently pull the cover
to loosen the fastening tape.
(Back Removal Instructions Continued)
33
32
Platinum Luxury-Lift®
Back Removal Instructions
FIGURE 2
FIGURE 1
FIGURE 3
Green and Green
(6-pin) Connectors Red and Black
(2-pin) Connectors
Power Supply
Connection to Chair
Fastening Tape on the Body
Outside Back Upholstery
Fastening Tape
Note: Image shows outside back cover loosened.
The fastening tape located on backside of the
body rear rail is not visible.
Body Rear Rail
Platinum Luxury-Lift®
Back Removal Instructions
35
34
Platinum Luxury-Lift®
Back Removal Instructions
– To reduce the risk of injury:
• The back of the unit must be lifted for assembly and disassembly. Please seek
assistance if you are unable to lift at least 45 pounds without strain.
WARNING
5. Unlock the back brackets and remove the back; there is one back bracket on each side of the back.
•Insert a slotted screwdriver between the back and one of the chair arms and locate the
locking lever on the back bracket (FIGURE 4).
•Carefully pry the back bracket locking lever up to about a 90 degree angle, until unlocked (FIGURE 4).
•Repeat these steps for the other back bracket. Once both back brackets are unlocked, the
back is free for removal.
•For a 1PL or 1PM chair, lift up on the back and remove it from the body. For a 1PH chair, lift up on
the back only high enough to rotate the back forward, toward the front of the chair, and lay it on
the top arms, taking care not to stretch or damage the electrical cables or connections between
the back and the body.
6. For a 1PH chair with adjustable headrest and lumbar features:
- Disconnect the adjustable headrest feature. Locate the connection with two blue connectors
on the left side (as sitting); one blue 6-pin connector routes from the back and the other
from the body. Open the locking cover and pull out on the connectors to disconnect the
adjustable headrest (FIGURE 5).
- Disconnect the adjustable lumbar feature. Locate the connection with two gray connectors
on the right side (as sitting); one 3-pin connector routes from the back and the other from
the body. Open the locking cover and pull out on the connectors to disconnect the
adjustable headrest (FIGURE 5).
7. Reverse these steps to reinstall the back. For easier installation, lay the back across the chair
arms, lift the back at a slight angle to align the back brackets to the body brackets and rotate
the back up, lowering it onto the body (FIGURE 6). Verify the back and body brackets are engaged
and lock both back brackets by pushing the locking lever down, refer to Important note below.
– To reduce the risk of injury:
• Do not operate the unit until the back is installed and locked.
WARNING
IMPORTANT:
Always make sure the back is properly installed with both sets of back and body brackets
engaged following back removal and reinstallation. To do this, stand behind the chair and
twist the back from side to side. If one or both sides move out of position, the back
brackets are not engaged with the body brackets (FIGURE 7). Remove the back and reinstall.
If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.
FIGURE 6
FIGURE 4
Back Bracket
Locking Lever
FIGURE 7
Back and Body Brackets Not Engaged--
Remove Back and Reinstall
Slotted Screwdriver
Body Bracket Back Bracket
FIGURE 5
Blue and Blue
(6-pin) Connectors Gray and Gray
(3-pin) Connectors
Furniture Placement
– To reduce the risk of serious injury:
• Provide a clear path for operation of the back and legrest. Place tables and area rugs
at a distance to allow the legrest to fully extend without rubbing or interference.
WARNING
To place your reclining unit the proper distance from the wall, fully recline the unit and leave
a minimum of 2" of space between the top of the back and the wall.
Place tables and area rugs at a distance to allow the legrest to fully extend without rubbing or interference.
Furniture Moving & Placement Guide
Moving the Platinum Lift Chair
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Before moving a Platinum Series chair, disconnect electrical plug from the wall outlet.
Moving the chair requires two people, one on each side of the chair lifting the frame
near the base; refer to the Operating Instructions online. Only move the product by
the lower arm frame, never by the legrest or reclining back.
WARNING
Moving the Platinum lift chair requires two people, one on each side of the chair. The back can
be removed for handling ease; refer to the Back Removal Instructions on preceding page.
1. Unplug the power supply from the electrical outlet.
2. Disconnect the 120 volt power cord from the power supply, and disconnect the power supply
from the power supply connector at the base of the unit. Refer to the Assembly Instructions.
3. Secure hand wand by carefully tucking it between the back and seat (or arm and seat if the
back is removed).
4. Have two people stand to the side of the chair (one on each side) and grip the lower arm
frame to lift and move the chair.
Important: If a hand
truck is used, only use
from the back of the
chair, never from the
front of the chair.
37
36
Tuck Hand Wand Between
Back and Seat
Grip Lower Arm Frame
(Page intentionally left blank)
Instrucciones importantes de seguridad.......................40-41
Instrucciones de ensamble del sillón Platinum
Luxury-Lift® .................................................................42-43
Instrucciones de ensamble de la batería de reserva
del sillón Platinum Luxury-Lift®...............................................44
Instrucciones de operación del sillón 1PL Platinum
Luxury-Lift®..........................................................................45-49
Instrucciones de operación del sillón 1PM Platinum
Luxury-Lift®con masajeador de 6motores y función
de calor...................................................................................50-55
Instrucciones de operación de la 1PH Platinum Luxury-Lift®
con mecanismo lumbar y apoyacabezas ajustable...............56-61
Funciones de operación adicionales del sillón Platinum
Luxury-Lift®............................................................................62
Solución de problemas del sillón Platinum Luxury-Lift®.............63-64
1PH Instrucciones para retirar el control remoto de Platinum
Luxury-Lift®............................................................................66
1PH Instrucciones para instalar el control remoto de Platinum
Luxury-Lift®....................................................................................67
Instrucciones para la remoción del respaldo de Platinum
Luxury-Lift®.......................................................................68-71
Guía de colocación y movimiento de muebles............................72
39
Índice
Exención de responsabilidad: la información y los productos que se presentan
en este manual pueden tener algunas diferencias con el producto que compró.
La-Z-Boy se reserva el derecho a realizar reemplazos que sean de igual
calidad y desempeño.
IMPORTANT
Lea las instrucciones de seguridad y otras instrucciones
antes de usar su Sillón Reclinable Eléctrico Platinum
Luxury-Lift®. Conserve este manual para utilizarlo como
referencia en el futuro.
38
¡Felicitaciones!
Usted es ahora el orgulloso propietario de un
Sillón Reclinable Eléctrico Platinum Luxury-Lift®,
de La-Z-Boy de última generación.
Usted ha seleccionado uno de los
productos tapizados de mayor calidad que
se producen en la industria de mobiliarios,
respaldado por nuestra experiencia de más
de 90 años en fabricación de alta calidad.
En La-Z-Boy nos sentimos orgullosos
de nuestros diseños y artesanía
y sabemos que usted gozará del
confort y estilo de su nuevo mueble.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
La-Z-Boy 1PM519 Manuel utilisateur
- Catégorie
- Masseurs
- Taper
- Manuel utilisateur
dans d''autres langues
- English: La-Z-Boy 1PM519 User manual
- español: La-Z-Boy 1PM519 Manual de usuario
Documents connexes
Autres documents
-
Panasonic EP1015 Manuel utilisateur
-
Human Touch Gravis ZG Manuel utilisateur
-
Cozzia EC-670 Le manuel du propriétaire
-
Sharper Image Human Touch® Gravis ZG Chair Le manuel du propriétaire
-
-
-
Graco 1762134 Manuel utilisateur
-
Ashley 2170306 Manuel utilisateur
-
Ashley 3500212 Manuel utilisateur