Braun IO Manuel utilisateur

Catégorie
Brosses à dents électriques
Taper
Manuel utilisateur
29
English 5
Français 16
www.oralb.com
www.oralb.ca
www.braun.com
www.service.braun.com
Braun GmbH
Frankfurter Strasse 145
61476 Kronberg
Germany/Alemania/Allemagne
Charger Type 3768
Handle Type 3758
Travel Case Type 3759
Power Cord Type 492-xxxx
Type de chargeur 3768
Type de manche 3758
Type d’étui de voyage 3759
Type de cordon d’alimentation 492-xxxx
90791650/XI-19
EN/FR
2
3
4
5
Description
1 Brush head
2 Brush head identification symbol
3 Smart Pressure Sensor (Light Ring)
4 Interactive Display
5 Handle
6 Charger
7 On/off button
8 Mode button
9 Interactive Display features
10 «Daily Clean» mode
11 «Sensitive» mode
12 «Gum Care» mode
13 «Whitening» mode
14 «Intense Clean» mode
15 «Super Sensitive» mode
16 «Tongue Clean» mode
17 Settings menu
18 Settings menu features
19 Manage Bluetooth® settings
20
Select/Change color of Light Ring
21 Select/Change language
22 Perform factory reset
23 Feedback features
24 Timer
25 Battery status
26 Exchange reminder
27 Brush feedback
Accessories and features:
a
Smart Pressure Sensor features
b Customize color of Light Ring via
Oral-B App
c
Brush head «Ultimate Clean»
d Brush head «Gentle Care»
e Brush head holder with cap
f Brush head holder stand
g Travel case
h Charging travel case
h1 Charging light
h2 Power cord (power supply)
i Download Oral-B App and connect to
Bluetooth® (see back page)
Note: Content may vary based on the model
purchased.
6
IMPORTANT SAFEGUARDS
When using electrical products, especially when children are present, basic safety precautions
should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
DANGER
In order to reduce the risk of electrocution:
1. Do not use while bathing.
2. Do not place or store the charger, power cord or charging travel case where it can fall or be pulled into
a tub or sink.
3. Do not place the charger, power cord or charging travel case in water or other liquid.
4. Do not reach for a charger, power cord or charging travel case that has fallen into water. Unplug
immediately.
WARNING
To reduce the risk of burns, electrocution, fire or injury:
1. Close supervision is necessary when this product is used by, on, or near children or persons with
disabilities.
2. Use this product only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer. Only use the charger provided with your appliance.
3. Keep cord away from heated surfaces.
4. Never drop the appliance or insert any object into any opening of the appliance.
5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has
been dropped or damaged or if it has been dropped into water. If any of these occur, please
contact a service center and return the product for examination and repair.
6. Do not use on self when drowsy or on another who is drowsy or sleeping.
7. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is
being administered.
IMPORTANT
1. Periodically check the entire product/cords/accessories for damage. A damaged or non-
functioning unit should no longer be used. If the product/cords/accessories are damaged, take it
to an Oral-B Service Center.
2. Do not touch the power plug with wet hands. This can cause an electric shock.
3. When unplugging, always pull the power plug instead of the cord. Avoid sharp bending, jamming
or squeezing of the cord. Never insert any object into any opening of the appliance.
4. Do not modify or repair the product. This may cause fire, electric shock or injury. Consult your
dealer for repairs or contact an Oral-B Service Center.
5. This appliance contains batteries that are non-replaceable. The appliance has no user serviceable
parts. Do not open and disassemble device except when disposing of the battery. Follow handling
and disposal instructions of the battery/device described in this manual.
6. Do not use on children under age 3.
7. This toothbrush is a personal care device and is not intended for use on multiple patients in a
dental practice or institution. For hygienic reasons we recommend the use of individual brush
handles and brush heads for each family member.
8. Only use the charger and/or special cord set (power supply) with integrated Safety Extra Low
Voltage power supply provided with your appliance. Do not exchange or tamper with any part of
it, otherwise there is risk of an electric shock. If charger/charging travel case is marked with
492-xxxx, only use Braun/Oral-B special cord set (power supply) with this identification.
9. Small parts may come off, keep out of reach of children.
CAUTION
To avoid brush head breakage which may generate a small parts choking hazard or damage teeth:
Prior to each use, ensure the brush head fits well. Discontinue use of the toothbrush, if brush head
no longer fits properly. Never use without a brush head.
If the toothbrush handle is dropped, the brush head should be replaced before the next use even if
no damage is visible
Replace brush head every 3 months or sooner if brush head becomes worn.
Clean brush head properly after each use (see «Cleaning recommendations» paragraph). Proper
cleaning ensures the safe use and functional life of the toothbrush.
If you are undergoing treatment for any oral care condition, consult your dental professional prior to use.
SAVE THESE INSTRUCTIONS
7
Important Information
This toothbrush, charger and pouch
(accessory) contain NdFeB magnets and
generate magnetic fields. If you use a medical
device or have an implanted medical device,
consult with the medical device manufacturer
or a physician, if you have questions about
safely using your Oral-B iO toothbrush.
Your Oral-B toothbrush can be used with your
smartphone (find details under «Connecting
your toothbrush to your Smartphone»). To
avoid electromagnetic interference and/or
compatibility conflicts, disable Bluetooth® on
your toothbrush handle (5) before using it in
surroundings, such as aircrafts or specially
marked areas in hospitals.
Disable Bluetooth by entering the «Settings»
menu on the interactive display (4) ->
Bluetooth -> disable. Follow the same
procedure to enable Bluetooth again.
Persons with pacemakers should always keep
the toothbrush more than six inches (15
centimeters) from the pacemaker while
turned on. Anytime you suspect interference
is taking place disable Bluetooth.
For satisfying RF exposure compliance
requirements, body-worn operations are
restricted to belt-clips, holsters or similar
accessories that have no metallic component
in the assembly and must provide at least
7.9 inches (20 centimeters) separation
between the device, including its antenna, and
the user's body.
Specifications
For voltage specifications refer to the bottom of
the charging unit.
First use
Please wake up your toothbrush by pressing the
on/off button (7) and follow the instructions on
the interactive display (4) to get started for first
time setup.
If not further instructed on the display, you may
toggle with the mode button (8) and select with
the on/off button (7).
You may change the settings via the «Settings»
menu (17) at any time.
Charging and Operating
To charge the battery place the toothbrush on
the plugged-in charger (6).
The charge level is indicated on the interactive
display (4). Once it is fully charged the display
turns off. A full charge typically takes 3 hours.
If the battery is running low the motor reduces
its speed and the Smart Pressure Sensor (3)
shortly blinks in red. Once the battery is empty,
the motor stops; it will need at least a 5-minute
charge for one usage.
Note: In case the battery is empty (display off),
charge at least for 30 minutes.
You can always store the handle on the
plugged-in charger to maintain it at full power;
a battery overcharge is prevented by device.
Note: Store handle at room temperature for
optimal battery maintenance.
Caution: Do not expose handle to temperatures
higher than 50°C / 122°F.
Using your toothbrush
Start Brushing
Place the brush head on the handle. A small gap
should remain between handle and brush head.
Lift the handle off the plugged-in charger or
simply pick it up to wake up the handle (display
turns on). Wet brush head and apply toothpaste.
To avoid splashing, guide the brush head to your
teeth before switching the handle on by pressing
the on/off button.
Note: Display turns off after some seconds. You may
press the on/off button to activate display again.
Guide the brush head from tooth to tooth. Brush
the outsides, the insides and the chewing
surfaces. Brush all four quadrants of your mouth
equally. You may also consult your dentist or
dental hygienist about the right technique for
you. After brushing, the display gives you
feedback based on your brushing time.
In the first days of using any electric toothbrush,
your gums may bleed slightly. In general, bleeding
should stop after a few days. Should it persist
after 2 weeks, please consult your dentist or
dental hygienist. If you have sensitive teeth and/
or gums, Oral-B recommends using the
«Sensitive» or «Super Sensitive» modes (optional
in combination with an Oral-B «Gentle Care»
brush head (d)).
Timer
The timer signals with a short stuttering sound at
30-seconds intervals to move to the next
quadrant of your mouth. A long stuttering sound
indicates the end of the professionally
recommended 2-minute brushing time.
The timer memorizes the elapsed brushing time,
even when the handle is briefly switched off
during brushing. The timer resets if pausing
longer than 30 seconds or placing the handle on
the plugged-in charger.
Note: During the use of the Oral-B App, the timer
may be deactivated for some features.
Note: You may also customize the timer settings
via Oral-B App.
English
8
Smart Pressure Sensor features (a)
Your toothbrush is equipped with a Smart
Pressure Sensor (3) that has various
functionalities indicated via different colors of
light:
White (default) = Operating indicator (choose
individual color via Oral-B App (b)) / Low
pressure indicator
Red = high pressure indicator / low battery
indicator
Green = recommended pressure indicator
Blue = Bluetooth pairing indicator
Orange = Error indicator (follow display
messages)
Brush with the right pressure indicated with a
green light. If too much pressure is applied, it
lights up in red reminding you to reduce pressure.
If the Smart Pressure Sensor illuminates in white
(or your pre-selected color), we recommend
applying more pressure. During high pressure the
brush head movement will be reduced (in «Daily
Clean», «Intense Clean» and «Sensitive» modes).
Periodically check the operation of the Smart
Pressure Sensor by pressing moderately on the
brush head during use.
Note: During the use of the Oral-B App, the Smart
Pressure Sensor feedback may be inactive for
some features.
Note: Smart Pressure Sensor is deactived during
«Tongue Clean» mode.
Brushing modes (depending on model)
Your toothbrush offers different brushing modes
indicated on the display:
«Daily Clean»– Standard mode for daily cleaning
«Sensitive» – Gentle, yet thorough cleaning for
sensitive areas
«Gum Care» – Gentle massage of gums
«Whitening» – Polishing for occasional or
everyday use
«Intense Clean» – For an extraordinary clean
feeling (operated with a higher speed)
«Super Sensitive» – Super gentle cleaning for
extra sensitive areas
«Tongue Clean» – Tongue cleaning for occasional
or everyday use
When operating the «Tongue Clean» mode, we
recommend using a «Gentle Care» brush head
(d). You can brush your tongue either with or
without toothpaste. Brush the whole area of your
tongue systematically in gentle movements. The
recommended brushing time is 30 seconds; the
motor stops after 30 seconds.
Mode setting:
You may first choose your default mode by
pressing the mode button (8) successively once
the handle is awake (display turned on). Select a
mode by pressing the on/off button (7). Your
toothbrush starts in the selected default mode.
You may also change modes during brushing.
Note: You may also customize mode settings via
Oral-B App.
Interactive Display
Turn on the interactive display (4) by pressing the
on/off button (7). If not further instructed on the
display, you may toggle with the mode button
and select with the on/off button.
(10-16) «Mode selection» - toggle by pressing the
mode button and select default start mode with
on/off button.
(17) «Settings» - toggle through all modes until
you reach the option «Settings»; to enter press
the on/off button:
-> (19) manage Bluetooth settings (enable,
disable)
-> (20) select/change color of Light Ring
-> (21) select/change language
-> (22) perform factory reset
(24) «Timer» - displays brushing time.
(25) «Battery status» - shows battery status after
use, when charging or when battery is low.
(26) «Exchange reminder» - reminds you when to
replace your brush head.
(27) «Brush feedback» – brushing feedback is
indicated with a smiley face.
«Brush waking» - when handle is picked up,
lifted off the plugged-in charger or when you
press the on/off button the handle indicates its
readiness.
«Error messages» - “outside operating limits”: you
are operating or charging outside standard
temperatures and/or above standard battery
current.
Brush heads
Oral-B offers you a variety of different Oral-B iO
brush heads (c/d) that only fit your Oral-B iO
toothbrush handle and can be used for
tooth-by-tooth precision cleaning.
Some iO Oral-B brush heads feature INDICATOR®
bristles to help you monitor brush head
replacement need. With thorough brushing, twice
a day for two minutes, the color will fade halfway
approximately within 3 months, indicating the
need to exchange your brush head. If the bristles
splay before the color recedes, you may exert too
much pressure on teeth and gums.
In general, we recommend replacing the brush
head every 3 months.
Connecting your toothbrush
to your Smartphone
The Oral-B App is available for smartphones
running iOS or Android
TM
operating systems. It
can be downloaded for free from App Store
TM
/
Google Play™ or you may scan the QR code on
the back page of this manual (i).
Launch the Oral-B App. It will guide you
9
through the entire Bluetooth pairing
procedure. You may also find it under the
App´s settings (More -> Your brush).
Note: Oral-B App functionality is limited if
Bluetooth is deactivated on your smartphone (for
directions please refer to your smartphone’s user
manual).
Pairing is indicated via the Smart Pressure
Sensor light. Any App instructions will be
displayed on your smartphone.
You may change Bluetooth settings at any
time on your handle via the display -> Settings
-> Bluetooth enable/disable.
Keep your smartphone in close proximity
(within 16ft/5m distance) when using it with
the handle. Make sure the smartphone is safely
positioned in a dry place.
Note: Your smartphone must support Bluetooth
4.2 (or higher)/Bluetooth Smart in order to pair
your handle. Check www.oralbappavailability.co.
uk for compatible smartphones and country
availability of the Oral-B App.
Caution: Follow your smartphone’s user manual
to ensure your phone/charger is designed for use
in a bathroom environment.
Cleaning recommendations
After brushing, rinse your brush head under
running water with the handle switched on.
Remove the brush head and clean the handle and
brush head separately. Make sure water runs
inside the top of the handle as well as inside the
brush head. Wipe all parts dry and let them
air-dry before reassembling your toothbrush
again.
Unplug the charger before cleaning. Clean the
charger regularly with a damp cloth.
Please check individual cleaning instructions for
each accessory in its “Accessories” paragraph.
Accessories
(depending on model)
Charging Travel Case (h)
To charge your handle (5) place it in the
charging travel case (h) and connect it to an
electric outlet, using the extra power supply
(h2) provided. The power supply may be used
for all global mains voltage ranges (100 –
240V).
The flashing light (h1) of the charging travel
case indicates that the handle is charging.
Once the handle is fully charged the light turns
off. A full charge typically takes 6 hours.
The outer and inner case should be cleaned
with a damp cloth only. Make sure that the
handle and brush head are completely dry
before storing in the travel case.
Note: Clean stains on travel case surface
immediately. Store travel case in a clean and dry
place.
Travel Case (g)
Store the clean and dry toothbrush/brush heads
in the travel case (g). The outer and inner case
should be cleaned with a damp cloth only.
Note: Clean stains on travel case surface
immediately. Store travel case in a clean and dry
place.
Brush head holder stand (f) / Brush head holder
with cap (e)
You may store your cleaned brush heads on the
pins of the brush head holders. Make sure brush
heads are dried before placing them in the holder
and/or closing the cap. Brush head holders and
cap are dishwasher-safe.
Zipper Pouch / Magnetic Pouch
Store the clean and dry toothbrush/brush heads
in the zipper pouch. The outer and inner case can
be cleaned under running water. Store the clean
and dry toothbrush along with the brush head
holder (e) in the magnetic pouch. Make sure
brush heads are dried before placing them into
the holder and/or closing the cap. The outer and
inner surfaces can be cleaned under running
water. Store pouches in a clean and dry place.
Note: Clean stains on pouch surfaces immediately.
Subject to change without notice.
Environmental Notice
Product contains batteries and/or
recyclable electric waste. For
environment protection do not dispose in
household waste, but for recycling take to electric
waste collection points provided in your country.
10
Do not disassemble the product except when
disposing of the battery. Run down battery
before removing. When taking out the battery for
disposal, use protective clothing (gloves, safety
glasses, etc.) to avoid direct skin contact with
batteries that may be subject to leakage. Use
caution not to short the positive (+) and negative
(–) terminals. Insulate terminals (e.g. with tape)
and put the battery in a plastic bag for disposal.
Open the handle as shown, remove the battery
and dispose of it according to local environmental
regulations.
Caution! Opening the handle will destroy the
appliance and invalidate the warranty.
Information
Bluetooth® radio module
Although all indicated functions on the Bluetooth
device are supported, Oral-B does not ensure
100% reliability in connection, and feature
operation consistency. Operation performance
and connection reliability are direct
consequences of each individual Bluetooth
device, software version, as well as the operating
system of those Bluetooth devices and company
security regulations implemented on the device.
Oral-B adheres to and strictly implements the
Bluetooth standard by which Bluetooth devices
can communicate and function in Oral-B
toothbrushes. However, if device manufacturers
fail to implement this standard, Bluetooth
compatibility and features will be further
compromised and the user may experience
functional and feature-related issues. Please note
that the software on the Bluetooth device can
significantly affect compatibility and operation.
Warranty – Exclusions and Limitations
This limited warranty applies only to the new
products manufactured by or for The Procter &
Gamble Company, its Affiliates or Subsidiaries
(“P&G”) that can be identified by the Braun /
Oral-B trademark, trade name, or logo affixed
thereto. This limited warranty does not apply to
any non-P&G product including hardware and
software. P&G is not liable for any damage to or
loss of any programs, data, or other information
stored on any media contained within the
product, or any non-P&G product or part not
covered by this limited warranty. Recovery or
reinstallation of programs, data or other
information is not covered under this limited
warranty. This limited warranty does not apply to
(i) damage caused by accident, abuse, misuse,
neglect, misapplication, or non-P&G product;
(ii) damage caused by service performed by
anyone other than Braun or authorized Braun
service location; (iii) a product or part that has
been modified without the written permission of
P&G, and (iv) damage arising out of the use of or
inability to use the Oral-B Smartphone stand/
puck, Smartphone mirror holder, or charging
travel case (“Accessories”).
LIMITATION OF LIABILITY
TO THE EXTENT PERMITTED BY APPLICABLE
LAW, IN NO EVENT SHALL P&G ITS
DISTRIBUTORS OR SUPPLIERS BE LIABLE TO
YOU OR ANY THIRD PARTY FOR ANY DIRECT,
INDIRECT, INCIDENTAL, CONSEQUENTIAL,
SPECIAL, EXEMPLARY OR PUNITIVE DAMAGES,
OF ANY NATURE WHATSOEVER, ARISING OUT
OF THE USE OF OR INABILITY TO USE THE
ORAL-B ACCESSORIES, INCLUDING, WITHOUT
LIMITATION, INJURY TO PERSONS, PROPERTY
DAMAGE, LOSS OF VALUE OF ANY THIRD
PARTY PRODUCTS THAT ARE USED IN OR WITH
THE ORAL-B ACCESSORIES, OR LOSS OF USE
OF THE ORAL-B ACCESSORIES OR ANY THIRD
PARTY PRODUCTS THAT ARE USED IN OR WITH
THE ORAL-B ACCESSORIES, EVEN IF P&G HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH
Battery removal at the end of the
product’s useful life
11
DAMAGES. WITHOUT LIMITING THE
FOREGOING, YOU UNDERSTAND AND AGREE
THAT P&G HAS NO LIABILITY FOR ANY
DAMAGE OR DESTRUCTION TO CONSUMER
ELECTRONICS DEVICES OR OTHER PERSONAL
PROPERTY THAT ARE CONTAINED ON OR
EXTERIOR TO THE ORAL-B ACCESSORIES, OR
ANY LOSS OF DATA CONTAINED IN THE
FOREGOING DEVICES. IN NO EVENT SHALL
ANY RECOVERY AGAINST ORAL-B EXCEED THE
ACTUAL PRICE PAID FOR THE PURCHASE OF
THE PRODUCT.
Warranty replacement brush heads
Oral-B warranty will be voided if electric
rechargeable handle damage is found to be
attributed to the use of non-Oral-B replacement
brush heads. Oral-B does not recommend the use
of non-Oral-B replacement brush heads.
Oral-B has no control over the quality of
non-Oral-B replacement brush heads.
Therefore, we cannot ensure the cleaning
performance of non-Oral-B replacement brush
heads, as communicated with the electric
rechargeable handle at time of initial purchase.
Oral-B cannot ensure a good fit of non-Oral-B
replacement brush heads.
Oral-B cannot predict the long-term effect of
non-Oral-B replacement brush heads on
handle wear.
All Oral-B replacement brush heads carry the
Oral-B logo and meet Oral-B’s high quality
standards. Oral-B does not sell replacement brush
heads or handle parts under any other brand
name.
Satisfaction Guaranteed or
Your Money Back:
Try it with no risk for 60 days!
If you are not 100% satisfied, call 1-877-593-4199
to receive a full refund. Return the product in its
original packaging along with the original cash
receipt postmarked within 60 days of purchase to
receive a pre-paid card in the amount of
purchase. Terms of prepaid card apply.
Your Oral-B toothbrush must be returned in its
original packaging and be postmarked no later
than 60 days after the date of purchase. Please
allow 6-8 weeks for handling. In the U.S., the
shipment return costs of the product is the
responsibility of the consumer. Sorry: No refunds
will be made for any Oral-B product damaged by
accident, neglect, unreasonable use or lost in the
post.
Terms and conditions apply. For further details
please contact our customer service.
12
Trouble Shooting
Problem Possible reason Remedy
APP
Handle does not
operate
(properly) with
Oral-B App.
1. Oral-B App is closed.
2. Bluetooth is not
activated on
smartphone.
3. Bluetooth is disabled on
handle.
4. Bluetooth connection to
smartphone has been
lost.
5. Your smartphone does
not support Bluetooth
4.2 (or higher)/Bluetooth
Smart.
6. Outdated Oral-B App.
1. Launch Oral-B App.
2. Activate Bluetooth on smartphone (described
in its user manual).
3. Enable Bluetooth via display Settings ->
Bluetooth enable.
4. Pair handle and smartphone again via App
settings. Keep your smartphone in close
proximity when using it with handle.
5. Your smartphone must support Bluetooth 4.2
(or higher)/Bluetooth Smart in order to pair
handle. Check www.oralbappavailability.co.uk
for compatible smartphones and country
availability of the Oral-B App.
6. Download latest Oral-B App.
Reset to factory
settings.
Original functionality
wanted.
Enter via display Settings -> Factory Reset (22).
Press on/off button to confirm.
TOOTHBRUSH
Handle is not
operating (during
first use).
1. Battery has a very low
charge level; handle does
not operate.
2. Operating outside
standard temperature
(message on display
and/or alternating lights
of Smart Pressure
Sensor)
1. Charge at least for 30 min.
2. Always operate in standard operating
temperatures (> 0°C and < 40°C).
Short stuttering
sounds after
2 minutes or
handle does not
operate any timer.
Timer has been modified/
deactivated via App.
Use App to change timer settings or perform
factory reset (see App Trouble Shootings).
Handle does not
charge.
1. Battery is at a very low
charger level (0%); it
may take up to 10-15min
until display turns on.
2. Ambient temperature for
charging is out of valid
range (< 0°C and >
40°C).
3. Charger may not be
(properly) connected.
1. Charge at least for 30min.
2. Recommended ambient temperature for
charging is 5°C to 35°C.
3. Ensure charger is connected to mains voltage.
Rattling/loud
noise during
brushing or
turning on.
1. Brush head may not be
placed correctly onto the
brush handle.
2. Brush head may be worn.
1. Check proper fit of brush head on handle. Small
gap remains in between.
2. Replace brush head.
13
FOR USA ONLY
Limited 2-Year Warranty
Oral-B warrants this appliance to be free of defects in material and workmanship for a
period of two years from the date of original purchase at retail. If the appliance exhibits
such a defect, Oral-B will, at its option, repair or replace it without cost for parts and
labor. The product must be carried in or shipped, prepaid and insured (recommended),
to an authorized Oral-B Service Center. Proof of date of original purchase is required.
The cost to ship the product to an authorized Service Center is the responsibility of the
consumer, the cost to return the product to the consumer is the responsibility of Oral-B.
This warranty does not cover finishes or normal wear, nor does it cover damage
resulting from accident, misuse, dirt, water, tampering, unreasonable use, service
performed or attempted by unauthorized service agencies, failure to provide reasonable
and necessary maintenance, including recharging, or units that have been modified or
used for commercial purposes.
This appliance is equipped with a Bluetooth Smart approved radio module. Failure to
establish a Bluetooth Smart connection to specific smart phones is not covered under
the device guarantee, unless the Bluetooth radio module of this appliance is damaged.
The Bluetooth devices are warranted by their own manufacturers and not by Oral-B.
Oral-B does not influence or make any recommendations to device manufacturers, and
therefore Oral-B does not assume any responsibility for the number of compatible
devices with our Bluetooth systems. Oral-B reserves the right, without any prior notice,
to make any technical modifications or changes to system implementation of device
features, interface, and menu structure changes that are deemed necessary to ensure
that Oral-B systems function reliably.
ALL IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO TWO YEARS FROM DATE OF ORIGINAL PURCHASE. IN NO EVENT
WILL ORAL-B BE RESPONSIBLE FOR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation may not apply to you. This
warranty gives you specific legal rights, and you may have other legal rights which vary
from state to state.
How to obtain service in the USA
Should this product require service, please call 1-800-566-7252 to be referred to the
authorized Oral-B Service Center closest to you.
To obtain service:
A. Carry the product in to the authorized Oral-B Service Center of your choice or,
B. Ship the product to the authorized Oral-B Service Center of your choice. Pack the
product well. Ship the product prepaid and insured (recommended). Include a copy
of your proof of purchase to verify warranty coverage, if applicable.
To obtain original Oral-B replacement parts and accessories:
Contact an authorized Oral-B Service Center.
Please call 1-800-566-7252 to be referred to the authorized Oral-B Service Center
closest to you.
To order original Oral-B replacement parts and accessories (including replacement
brush heads) by phone: Please call 1-800-566-7252.
To speak to an Oral-B Consumer Service Representative: Please call 1-800-566-7252.
14
Suppliers Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Oral-B iO
Responsible Party The Procter & Gamble Co.
1 P&G Plaza
Cincinnati, OH 45202
Internet contact
information
www.oralb.com
FCC Compliance
Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Section 15.21 Information to user:
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Section 15.105 (b)
Note: This equipment has been tested and found to comply with the Limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
15
FOR CANADA ONLY
Limited 2-Year Warranty
In the event this appliance fails to function within the specified warranty period because
of defects in material or workmanship, and the consumer returns the unit to an
authorized service Center, Braun Canada will, at its option either repair or replace the
unit without additional charge to the consumer. This warranty does not cover any
product which has been damaged by dropping, tampering, servicing performed or
attempted by unauthorized service agencies, misuse or abuse. This warranty excludes
units which have been modified or used for commercial purposes.
This appliance is equipped with a Bluetooth Smart approved radio module. Failure to
establish a Bluetooth Smart connection to specific smart phones is not covered under
the device guarantee, unless the Bluetooth radio module of this appliance is damaged.
The Bluetooth devices are warranted by their own manufacturers and not by Oral-B.
Oral-B does not influence or make any recommendations to device manufacturers, and
therefore Oral-B does not assume any responsibility for the number of compatible
devices with our Bluetooth systems. Oral-B reserves the right, without any prior notice,
to make any technical modifications or changes to system implementation of device
features, interface, and menu structure changes that are deemed necessary to ensure
that Oral-B systems function reliably.
To the extent allowed by law, Braun Canada shall not be responsible for loss of the
product, loss of time, inconvenience, commercial loss, special or consequential
damages. The provisions of this warranty are in addition to and not a modification of or
subtraction from the statutory warranties and other rights and remedies contained in
applicable provincial legislation.
How to obtain service in Canada
Should this product require service, please call 1-800-566-7252 to be referred to the
authorized Oral-B Service Center closest to you.
To obtain service:
A. Carry the product in to the authorized Oral-B Service Center of your choice or,
B. Ship the product to the authorized Oral-B Service Center of your choice. Pack the
product well. Ship the product prepaid and insured (recommended). Include a copy
of your proof of purchase to verify warranty coverage, if applicable.
To obtain original Oral-B replacement parts & accessories: Contact an authorized Oral-B
Service Center.
Please call 1-800-566-7252 to be referred to the authorized Oral-B Service Center
closest to you.
To speak to an Oral-B Service Representative: Please call 1-800-566-7252.
IC Compliance Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
16
Description
1 Brossette
2 Symbole d’identification de la brossette
3 Détecteur de pression intelligent
(Témoin Lumineux)
4
Écran interactif
5 Manche
6 Chargeur
7 Bouton Marche/arrêt
8 Bouton pour le mode
9 Caractéristiques de l’écran interactif
10 Mode « Nettoyage quotidien »
11 Mode « Sensible »
12 Mode « Soin des gencives »
13 Mode « Blanchissant »
14 Mode « Nettoyage intense »
15 Mode « Hyper sensible »
16 Mode « Nettoyage de la langue »
17 Menu des paramètres
18 Caractéristiques du menu des
paramètres
19
Gestion des paramètres de la fonction
Bluetooth®
20
Sélectionner/modifier la couleur du
témoin lumineux
21
Sélection/changement de la langue
22 Réinitialisation des paramètres par
défaut
23
Caractéristiques de la rétroaction
24 Minuteur
25 État de la pile
26 Rappel de remplacement
27 Rétroaction sur le brossage
Accessoires et caractéristiques
a
Caractéristiques du détecteur de
pression intelligent
b
Personnalisation de la couleur du témoin
lumineux via l’application Oral-B
c
Brossette « Ultimate Clean »
d Brossette « Gentle Care »
e Support à brossettes avec capuchon
f Socle du support à brossettes
g Étui de voyage
h Étui de voyage avec chargeur intégré
h1 Voyant lumineux de chargement
h2 Cordon d’alimentation (bloc
d’alimentation)
i
Téléchargement de l’application Oral-B
et connexion à Bluetooth® (voir la
dernière page)
Remarque : Le contenu peut varier selon le
modèle.
17
CONSIGNES DE SÉCURITÉ IMPORTANTES
Toujours suivre les consignes de sécurité suivantes lorsqu’un appareil électrique est utilisé, surtout en présence d’un enfant :
LIRE TOUTES LES INSTRUCTIONS AVANT D’UTILISER CET APPAREIL
DANGER
Pour réduire les risques d’électrocution :
1. Ne pas utiliser dans le bain ou la douche.
2. Éviter de placer ou de ranger le chargeur, le cordon d’alimentation ou l’étui de voyage avec chargeur intégré à un
endroit d’où il pourrait tomber ou être poussé dans la baignoire ou le lavabo.
3. Éviter de placer le chargeur, le cordon d’alimentation ou l’étui de voyage avec chargeur intégré dans l’eau ou dans tout
autre liquide.
4. Ne pas toucher le chargeur, le cordon d’alimentation ou l’étui de voyage avec chargeur intégré s’ils sont tombés dans
l’eau. Le débrancher immédiatement.
MISE EN GARDE
Afin de réduire les risques de brûlure, d’électrocution, d’incendie ou de blessure :
1. L’utilisation de ce produit par un enfant ou une personne handicapée, ou en présence de ces derniers, doit être faite
sous étroite supervision.
2. Ce produit est conçu pour être utilisé conformément au mode d’emploi. Ne pas utiliser d’autres accessoires que ceux
recommandés par le fabricant. Utiliser seulement le chargeur fourni avec l’appareil.
3. Tenir le cordon loin des surfaces chaudes.
4. Ne jamais laisser tomber l’appareil ni introduire un objet dans un quelconque orifice de l’appareil.
5. Ne jamais utiliser ce produit si la prise ou le cordon sont endommagés, s’il ne fonctionne pas correctement, s’il est
tombé, s’il a été endommagé ou s’il a été immergé dans l’eau. Si l’une de ces situations se produit, veuillez
communiquer avec un centre de services et retourner le produit pour qu’il soit examiné et réparé.
6. Ne pas utiliser si vous êtes somnolent ou sur une autre personne somnolente ou endormie.
7. Ne pas utiliser à l’extérieur ni à des endroits où des aérosols sont pulvérisés ou que de l’oxygène est administré.
IMPORTANT
1. Vérifier périodiquement que le produit/le cordon/les accessoires en entier ne sont pas endommagés. Ne pas utiliser un
appareil électrique endommagé ou qui ne fonctionne plus. Si le produit, le cordon ou les accessoires sont
endommagés, les apporter dans un centre de services Oral-B.
2. Ne pas toucher la prise d’alimentation avec les mains mouillées. Il y a risque d’électrocution.
3. Au moment de débrancher l’appareil, toujours tirer la prise, jamais le cordon d’alimentation. Éviter de plier
brusquement, de coincer ou de serrer le cordon. Ne jamais introduire un objet dans un quelconque orifice de l’appareil.
4. Ne pas modifier le produit et ne pas tenter de le réparer. Cela pourrait causer un incendie, une électrocution ou une
blessure. Communiquer avec le détaillant ou le centre de services Oral-B si des réparations sont nécessaires.
5. Cet appareil contient des piles qui ne peuvent pas être remplacées. Cet appareil ne contient aucune pièce pouvant
être réparée par l’utilisateur. Ne pas l’ouvrir ni le démonter, sauf pour en retirer la pile. Manipuler cet appareil et retirer
la pile conformément au mode d’emploi.
6. Ne convient pas aux enfants de moins de 3 ans.
7. Cette brosse à dents est un appareil de soins personnels et n’est pas conçue pour être utilisée avec plusieurs patients
dans un cabinet ou une institution dentaire. Pour des raisons d’hygiène, nous recommandons d’utiliser des brossettes
et des manches de brosse à dents individuels pour chaque membre de la famille.
8. Utiliser seulement le chargeur ou le cordon spécial (bloc d’alimentation) avec un bloc d’alimentation intégré à sortie de
basse tension de sécurité fourni avec votre appareil. Ne pas modifier ou échanger aucune des parties, car autrement, il
y a des risques d’électrocution. Si le symbole 492-xxxx se trouve sur le chargeur/l’étui de voyage avec
chargeur intégré, utiliser seulement le cordon d’alimentation (bloc d’alimentation) spécial de Braun/Oral-B.
9. De petites pièces peuvent se détacher. Tenir hors de la portée des enfants.
ATTENTION
Pour éviter que la brossette ne se brise, ce qui pourrait générer de petites pièces qui représenteraient un risque
d’étouffement ou endommager les dents :
S’assurer que la brossette s’emboîte bien avant chaque utilisation. Arrêter d’utiliser la brosse à dents si la brossette
tient moins bien sur le manche. Ne jamais utiliser la brosse sans brossette.
Remplacer la brossette avant l’utilisation si l’appareil tombe et ce, même si aucun dommage n’est apparent.
Remplacer la brossette tous les 3 mois, ou plus tôt si la brossette est usée.
Bien nettoyer la brossette après chaque utilisation (voir le paragraphe sur l’« Entretien »). Un nettoyage approprié de
la brosse permet de garantir son utilisation sécuritaire et sa durée de vie.
Si vous suivez un traitement pour une affection buccale, consultez un professionnel des soins buccodentaires avant
d’utiliser la brosse à dents.
CONSERVER CE MODE D’EMPLOI
18
Renseignements importants
Cette brosse à dents, ce chargeur et cette
pochette (accessoire) contiennent des aimants
NdFeB et génèrent des champs magnétiques.
Si vous utilisez un dispositif médical ou si vous
portez un implant médical, veuillez consulter le
fabricant du dispositif médical ou un médecin
pour toute question concernant l’utilisation
sécuritaire de votre brosse à dents Oral-B iO.
Votre brosse à dents Oral-B peut être utilisée
avec votre téléphone intelligent (pour plus de
détails, recherchez « Connectez votre brosse à
dents à votre téléphone intelligent »). Pour
éviter tout problème de compatibilité ou
d’interférence électromagnétique, désactivez
Bluetooth® du manche de votre brosse à
dents (5) avant de l’utiliser dans des zones
réglementées comme les avions ou les endroits
spécialement désignés dans les hôpitaux.
• Désactivez Bluetooth à partir du menu des
paramètres depuis l’écran interactif (4) ->
Bluetooth -> désactiver. Suivez la même
procédure pour réactiver Bluetooth.
Les personnes qui ont un stimulateur
cardiaque doivent toujours garder la brosse à
dents à plus de 15 centimètres (6 pouces) du
stimulateur lorsque celle-ci est en marche. Si
vous pensez qu’il y a interférence, désactivez
Bluetooth.
Afin d’assurer la conformité aux exigences en
matière d’exposition aux RF, les supports près
du corps se limitent aux chaînes à ceintures,
aux étuis et à tout autre accessoire qui ne
contiennent pas de composantes métalliques
et doivent maintenir l’appareil, y compris son
antenne, à une distance de 20 centimètres
(7,9 pouces) du corps de l’utilisateur.
Spécifications
Pour connaître les spécifications électriques,
consulter les renseignements imprimés sous le
chargeur.
Première utilisation
Veuillez réveiller votre brosse à dents en
appuyant sur le bouton Marche/arrêt (7) et suivez
les directives sur l’écran interactif (4) pour
démarrer la première configuration.
Si d’autres instructions n’apparaissent pas à
l’écran, vous pouvez faire basculer à l’aide du
bouton pour le mode (8) et sélectionner le
bouton Marche/arrêt (7).
Vous pouvez modifier les paramètres depuis le
menu des paramètres (17) en tout temps.
Chargement et
fonctionnement
Pour charger la pile, placer la brosse à dents
dans le chargeur (6) branché.
Le niveau de charge est indiqué sur l’écran
interactif (4). Lorsque la brosse est
complètement chargée, l’écran s’éteint. Il faut
compter environ 3 heures pour charger
complètement l’appareil.
Si la pile est faible, la vitesse du moteur est
réduite et le détecteur de pression intelligent
(3) tourne au rouge et clignote brièvement.
Lorsque la pile est complètement déchargée,
le moteur s’arrête et la brosse devra être
chargée pendant au moins 5 minutes avant
d’être utilisée pour un brossage.
Remarque : Si la pile est complètement
déchargée (l’écran ne s’allume pas), charger
pendant au moins 30 minutes.
Vous pouvez toujours ranger le manche de la
brosse à dents sur le chargeur pour qu’il
conserve une charge maximale. Il n’y a aucun
risque de surcharger la pile.
Remarque : Ranger le manche de la brosse à
dents à une température ambiante pour un
maintien optimal de la pile.
Attention : Ne pas exposer le manche à des
températures de plus de 50 °C (122 °F).
Brossage des dents
Commencer le brossage
Placer la brossette sur le manche. Il devrait rester
un petit espace entre le manche et la brossette.
Soulever le manche du chargeur branché ou le
ramasser pour réveiller le manche (l’écran
s’allume). Mouiller la brossette et appliquer du
dentifrice. Pour éviter les éclaboussures, placer la
brosse sur les dents avant de la mettre en marche
en appuyant sur le bouton Marche/arrêt.
Remarque : L’écran s’éteint après quelques
secondes. Vous pouvez appuyer sur le bouton
Marche/arrêt pour activer l’écran.
Déplacer la brossette d’une dent à l’autre. Brosser
les surfaces extérieures des dents, les surfaces
intérieures, et les surfaces de mastication. Brosser
les quadrants de la bouche de façon égale. Vous
pouvez également consulter votre dentiste ou
votre hygiéniste dentaire pour savoir quelle
technique vous convient le mieux. Après le
brossage, l’écran vous donne une rétroaction
selon le temps de brossage.
Durant les premiers jours d’utilisation d’une
brosse à dents électrique, il est possible que vos
gencives saignent légèrement. En général, ces
saignements devraient cesser au bout de
quelques jours. S’ils persistent plus de deux
Français
19
semaines, veuillez consulter un dentiste ou un
hygiéniste dentaire. Oral-B recommande aux gens
dont les dents ou les gencives sont sensibles
d’utiliser le mode « Sensible » ou « Hyper sensible »
(optionnel en combinaison avec la brossette
« Gentle Care » (d)).
Minuteur
Le minuteur émet un bref son saccadé toutes les
30 secondes pour vous indiquer le moment de
changer de quadrant. Un long signal indique la fin
du brossage de 2 minutes recommandé par les
dentistes.
Le minuteur mémorise le temps de brossage
écoulé, même lorsque le manche est brièvement
mis en arrêt pendant le brossage. Le temps est
remis à zéro lorsque le manche est mis en arrêt
pendant plus de 30 secondes ou lorsque le
manche est déposé sur le chargeur branché.
Remarque : Lors de l’utilisation de l’application
Oral-B , le minuteur peut être désactivé pour
certaines caractéristiques.
Remarque : Vous pouvez également personnaliser les
paramètres du minuteur grâce à l’application Oral-B.
Caractéristiques du détecteur de pression
intelligent (a)
Votre brosse à dents est dotée d’un détecteur de
pression intelligent (3) dont les nombreuses
fonctionnalités sont indiquées par des voyants
lumineux de différentes couleurs :
Blanc (par défaut) = Voyant de mise en marche
(choisir une couleur via l’appli Oral-B (b)) /
Voyant de faible pression
Rouge = voyant de forte pression / voyant de pile
faible
Vert = voyant de pression idéale
Bleu = Voyant de pairage Bluetooth
Orange = Voyant d’erreur (suivre les directives sur
l’écran)
Brosser avec la pression idéale indiquée par la
lumière verte. Si vous exercez trop de pression sur
vos dents, le voyant rouge s’allumera pour vous
rappeler d’appliquer moins de pression. Si le voyant
du détecteur de pression intelligent est blanc (ou
votre couleur choisie), nous recommandons
d’appliquer plus de pression. Lorsque la pression est
forte, le mouvement de la brossette sera réduit
(dans les modes « Nettoyage quotidien »,
« Nettoyage intense » et « Sensible »). Assurez-vous
régulièrement du bon fonctionnement du détecteur
de pression intelligent en appuyant modérément
sur la brossette lorsque vous vous brossez les dents.
Remarque : Pendant l’utilisation de l’application
Oral-B , la rétroaction du détecteur de pression
intelligent peut être désactivée pour certaines
caractéristiques.
Remarque : Le détecteur de pression intelligent est
désactivé lors du mode « Nettoyage de la langue ».
Modes de brossage (selon le modèle)
Votre brosse à dents offre des différents modes
de brossage indiqués sur l’écran :
« Nettoyage quotidien » – Mode standard pour le
nettoyage quotidien
« Sensible » – Pour un nettoyage en douceur mais
complet des zones sensibles
« Soin des gencives » - Pour masser délicatement
les gencives
« Blanchissant » – Pour un polissage occasionnel
ou quotidien
« Nettoyage intense » – Pour une sensation
extraordinaire de propreté (nettoyage effectué à
vitesse plus élevée)
« Hyper sensible » – Pour un nettoyage en grande
douceur mais complet des zones très sensibles
« Nettoyage de la langue » – Pour un nettoyage
de la langue quotidien ou occasionnel
Lorsque vous utilisez le mode « Nettoyage de la
langue », nous vous recommandons d’utiliser la
brossette « Gentle Care » (d). Vous pouvez
brosser votre langue avec ou sans dentifrice.
Brossez toute la surface de votre langue en
effectuant des mouvements délicats. Le temps de
brossage recommandé est de 30 secondes; le
moteur s’arrête après 30 secondes.
Réglage du mode :
Vous pouvez d’abord choisir votre mode par défaut
en appuyant successivement sur le bouton pour le
mode (8) lorsque le manche est réveillé (l’écran est
allumé). Pour sélectionner un mode, appuyer sur le
bouton Marche/arrêt (7). La brosse à dents démarre
avec le mode de brossage par défaut. Vous pouvez
également changer le mode lors du brossage.
Remarque : Vous pouvez également personnaliser
les paramètres du mode grâce à l’application Oral-B.
Écran interactif
Allumer l’écran interactif (4) en appuyant sur le
bouton Marche/arrêt (7). Si d’autres instructions
n’apparaissent pas à l’écran, vous pouvez faire
basculer à l’aide du bouton pour le mode et
sélectionner le bouton Marche/arrêt.
(10 à 16) « Choix de mode de brossage » – faire
basculer en appuyant sur le bouton pour le mode
et sélectionner le mode de départ par défaut
avec le bouton Marche/arrêt.
(17) « Paramètres » – basculer entre les modes
jusqu’à ce que l’option « Paramètres » apparaisse.
Pour y accéder, appuyer sur le bouton Marche/arrêt :
-> (19) Gestion des paramètres de la fonction
Bluetooth (activer, désactiver)
-> (20) Sélection/changement de la couleur du
témoin lumineux
-> (21) Sélection/changement de la langue
-> (22) Réinitialisation des paramètres par défaut
(24) « Minuteur » – affiche le temps de brossage.
(25) « État de la pile » – affiche l’état de la pile
après l’utilisation, lorsqu’elle charge et lorsque la
pile est faible.
(26) « Rappel de remplacement » – indique quand
remplacer votre brossette.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

Braun IO Manuel utilisateur

Catégorie
Brosses à dents électriques
Taper
Manuel utilisateur

dans d''autres langues