KitchenAid KGRT507GBS0 Le manuel du propriétaire

and Care Guide

TO THE iNSTALLER: PLEASE LEAVE THIS

iNSTRUCTiON BOOK WITH THE UNIT.

TO THE CONSUMER: PLEASE READ

AND KEEP THiS BOOK FOR FUTURE

REFERENCE.

!_<i>!_?_!. li_i _ i! ¸_!; %..I/_i_>_i?

A Note to You ................................................. 2

Range Safety ................................................... 3

Parts and Features ......................................... 5

Using and Caring for Your Cooktop ............. 9

Using the surface burners ..........................9

Energy saving tips .................................... 11

Cookware tips .......................................... 12

Caring for your cooktop ............................ 13

Cleaning your cooktop ............................. 15

Using and replacing the surface light ....... 16

Using and Caring for Your Oven ................. 18

Using the electronic oven control ............. 18

Setting the clock ....................................... 26

Using the timer ......................................... 27

Oven settings ........................................... 28

Cooking tips ............................................. 29

Bake or Convection Bake ........................ 31

Broil .......................................................... 33

Convection Broil ....................................... 35

Convection Roast ..................................... 37

Adjusting the oven temperature ............... 38

Using the temperature probe ................... 40

Using Convect Full Meal .......................... 43

Using EASY CONVECT TM Conversion....46

Timed cooking .......................................... 48

Dehydrating .............................................. 51

Raising (proofing) bread ........................... 53

Cleaning your oven and controls ............. 55

Oven lights ............................................... 57

Using the Self-Cleaning Cycle .................... 58

Before you start ........................................ 58

Before setting the controls ....................... 59

Setting the controls .................................. 59

For best cleaning results .......................... 61

How the cycle works ................................ 61

Troubleshooting ............................................ 62

Requesting Assistance or Service .............. 66

Warranty ........................................................ 68

in the U.S.A. for assis|ance or service,

.........call the Consumer Assistance center:

In Canada, for assistance or service,

see page 67.

KITCHENAID ®THERMAL-CONVECTION TM

Gas Freestanding and Slide-in Ranges

Models: KGRT507 KGST307

YKGRT507 YKGST307

9753310A www,kitchenaid,com

Note toYou

KITCHENAID ®designs the best tools for the most important room in your house. To

ensure that you enjoy many years of trouble-free operation, we developed this Use and

Care Guide. It contains valuable information concerning how to operate and maintain

your new appliance properly and safely. Please read it carefully. Also, please complete

and mail the enclosed Product Registration Card.

Whenever you call our Consumer

Assistance Center at 1-800-422-1230 (in

Canada, 1-800-461-5681) or request

service for your appliance, you need to

know your complete model number and

serial number. You can find this information

on the model and serial number plate (see

diagram on pages 5 -6 for location of plate).

Please also record the purchase

information.

Model Number

Serial Number

Purchase/

Installation Date

Builder/Dealer

Name

Address

Phone

NOTE: You must provide proof of purchase

or installation date for in-warranty service.

Keep this book and the sales slip together in a safe place for future reference.

WARNING: if the information in this manual is not followed

exactly, a fire or explosion may result causing property damage,

personal injury or death.

Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

, Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

• if you cannot reach your gas supplier, call the fire department.

= Installation and service must be performed by a qualified installer,

service agency or the gas supplier.

Safety

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your

appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the

word "DANGER" or "WARNING." These words mean:

You will be killed or seriously injured

if you don't follow instructions.

You can be killed or seriously injured

if you don't follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury,

and tell you what can happen if the instructions are not followed.

The range will not tip during normal use. However, tipping can occur if you apply too much

force or weight to the open door without the anti-tip bracket properly secured.

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

See the installation instructions for details.

Failure to follow these instructions can result in death or

serious burns to children and adults.

Anti-Tip Bracket

Range Foot

Making sure the anti-tip bracket is installed:

,, Slide range forward.

,, Look for the anti=tip bracket securely attached to f{oor.

o Slide range back so rear range foot is under anti-tip bracket.

i_iil_!_i:!i ange Safety

iMPORTANT SAFETY iNSTRUCTIONS

WARNING: To reduce the risk of fire,

electrical shock, injury to persons, or

damage when using the range, follow

basic precautions, including the following:

•WARNING - TOREDUCETHE

RISK OF TIPPING OF THE RANGE,

THE RANGE MUST BE SECURED BY

PROPERLY INSTALLED ANTI-TIP

DEVICES. TO CHECK IF THE

DEVICES ARE INSTALLED PROPERLY,

SLIDE RANGE FORWARD, LOOK FOR

ANTI-TIP BRACKET SECURELY

ATTACHED TO FLOOR, AND SLIDE

RANGE BACK SO REAR RANGE

FOOT IS UNDER ANTI-TIP BRACKET.

•CAUTION - Donot store items of

interest to children in cabinets above a

range or on the backguard of a range -

children climbing on the range to reach

items could be seriously injured.

• Proper Installation - The range, when

installed, must be electrically grounded

in accordance with local codes or, in the

absence of local codes, with the Nation-

al Electrical Code, ANSI/NFPA 70. Be

sure the range is properly installed and

grounded by a qualified technician.

• This range is equipped with a three-prong

grounding plug for your protection against

shock hazard and should be plugged

directly into a properly grounded

receptacle. Do not cut or remove the

grounding prong from this plug.

• Disconnect the electrical supply before

servicing the appliance.

• Never Use the Range for Warming or

Heating the Room.

• Injuries may result from the misuse of

appliance doors or drawers such as

stepping, leaning, or sitting on the

doors or drawers.

• Maintenance - Keep range area clear and

free from combustible materials, gasoline,

and other flammable vapors and liquids.

• Storage in or on the Range -

Flammable materials should not be

stored in an oven or near surface units.

• Top burner flame size should be adjust-

ed so it does not extend beyond the

edge of the cooking utensil.

For self-cleaning ranges -

• Before Self-Cleaning the Oven - Remove

broiler pan and other utensils. Wipe off all

excessive spillage before initiating the

cleaning cycle.

-SAVE THESE INSTRUCTIONS-

and Features

ilSiiii¸d_:!!i_,_¸iii!i_¸_ _'_,__,1_::::;_,,di_i__sili

Vent guard piece .........................

Surface

(the style of your

grates may vary)

(p. 9)

Surface burner controls

(p. 10, 11)

Anti-tip bracket

(p. 3)

Model and serial

number plate

(p. 2) ............................

Broil pan

Removable storage

drawer

(containing

broiler pan, grid, and

convection roasting rack)

(p. 8)

.................Oven vent

(p. 7)

Electronic oven

control

(p. 18-29)

Automatic

oven light

switch

(p. 57)

burner

(not shown)

Bake burner

(not shown)

REAR FRONT

[] []

OFF OFF

...Q.....Q..

• D • • • •

Left rear Left front

control knob control knob

Right front

control knob

REAR

@

Right rear

control knob

i_iil_!_i_i!i_!ii_rts and Features

!ii_:@,Oiii',iiii"_i,,,,,_,iiiii,,_@,iiOC:Cti_'_ii0 !iii,,_"_s

{ i!i!::::¸_i¸'_:!!__i!__!!i;t_i_i:_ii_,_c!ii¸_i_ig _'!__1o di_'_;_:!i__:!!_;}

Surface light

(some freestanding

models)

(pp. 16, 17)

Surface ......

burners

(the style of your

grates may vary)

(p. 9)

Surface burner

controls

(pp. 10, 11)

Anti-tip

bracket

(p. 3)

Model and serial

number plate

(p. 2)

Broil pan

support

Oven vent

(p. 7)

Electronic

oven control

(pp. 18-29)

Automatic

oven light

switch

(p. 57)

Broil burner

(not shown)

Bake burner

(not shown)

drawer

(containing

broiler pan, grid, and

convection roasting rack)

(p. 8)

OFF OFF _ f OFF OFF

..-... _--.-,o _,; • • ,o _/_/ _,_;• • ,o _,_;. • _oz.........-..

Left rear Left front Right front Right rear

control knob control knob control knob control knob

rts and Features

Hot air and moisture escape from the oven

through a vent in the center rear of the

cooktop. The vent lets air circulate properly.

Be careful not to block the vent, or you will

get poor baking/roasting results.

NOTE: Never store plastics, paper, or other

items that could melt or burn near the oven

vent, or any of the surface burners.

Oven vent

'' "' :JJ_:i ":_' Oven door vent

Hot air and moisture may escape from the

door vent during certain oven modes. Some

condensation may be observed occasional-

ly. This will not affect cooking performances.

Removing the oven door:

1. Open the door to the Broil Stop position

(open about 4" [10 cm]).

2. Lift door slightly and pull out and back until

hinges come out to the catch position.

3. Push door down and pull straight out to

remove door completely.

Replacing the oven door:

1. Holding the door by the handle, place

1

the top of the door under the cooktop

overhang and use your leg to apply

pressure to slide hinges into the slots as

far as possible.

Open door to the broil position or slightly

past it.

Using the side of your leg, apply

pressure to the bottom of the door front.

Lift the door slightly while applying

pressure to push, until the hinges have

gone in fully.

i_iil_!:i_i!i ii_rts and Features

ii}:::_'O_!!_ii_iii'_iiiO,_ii'__"!ii_i_""!_!!iiil;{il;! _!}l"_i};ii_"'_ii_;:;:ii_;i_;,_ii:i;il;;l_,(il;iiiii""'!,Ov,_i;;;iiii_i!_,,!ii"''iiiili"_"'ii_:i_:;:iii!'ff_

To position the pan over the bake shield, the

two guides on the pan should be placed over

the notches on the shield. The position is

important to maintain an even heat in the

oven.

!!iiil;;il;_,,¸¸Cii!{,_;i_i!i;i_,,

You can remove the storage drawer to make it easier to clean under the range. Use care

when handling the drawer.

Removing the storage drawer: Replacing the storage drawer:

rail

1. Empty drawer of any pots and pans

before removing drawer. Use recessed

area on top edge of drawer to pull draw-

er straight out to the first stop. Lift front

and pull out to the second stop.

2. Lift back slightly and slide drawer all the

way out.

1. Fit ends of drawer slide rails into the

drawer guides on both sides of opening.

2. Lift drawer front and press in until metal

stops on drawer slide rails clear white

stops on drawer guides. Lift drawer front

again to clear second stop and slide

drawer closed.

"ngand Caring for Your

Cooktop

LIsill !!i:i:iiii iJ

Your cooktop has sealed gas burners with

an auto-reignition system. The sealed burn-

ers spread the heat evenly across the bot-

tom of the cookware and provide infinite

heat control. The auto-reignition system

senses when a burner flame has gone out

and will automatically reignite that burner.

When to use the left rear and

right front burners:

IMPORTANT: Your cooktop is factory-set

for use with Natural Gas. If you wish to

use L.P. gas, an L.P. Gas Conversion Kit

is included with your new range. See the

appropriate section of the Installation

Instructions for details on making this

conversion.

6,000 BTU burner

When to use the right rear

and left front burners:

10,000 BTU burner

Use these burners for simmering or for

cooking smaller quantities of food requiring

small cookware.

10,000 BTU burner

Use these burners for cooking large quanti-

ties of food, deep-fat frying, or cooking with

large cookware.

iii and Caring for Your Cooktop

Using the surface burners:

Control knobs

1. Grasp the control knob.

2. Push down and turn to HI. The electric

spark ignitor will ignite the gas flowing into

the burner. When you hear a clicking

sound, you know that the ignitors are

working. Gas is flowing as long as knob is

not set at OFF.

3. When the burner is lit, turn the control

knob to the desired flame setting. (See the

guide under "Burner heat settings" later in

this section.) You can turn the knobs to

any of the marked settings. The ignitor will

turn off and the clicking will stop when the

burner ignites.

NOTES:

• The ignitors may click a number of times

before burner lights. This is normal.

, All four burner ignitors will spark

regardless of which burner you are using.

, Visually check that the burner has lit. If the

burner does not ignite, listen for the clicking

sound. If you do not hear the ignitor click,

TURN THE BURNER OFF. Check that the

service cord is placed firmly in the wall

receptacle. Check for a tripped circuit

breaker or blown fuse.

Check that the control knob is pressed

completely down on valve shaft. If the spark

ignitor still fails to operate, call your

nearest designated service outlet.

Proper grounding and polarity are

necessary for correct operation of the electric

ignition system. If the wall receptacle does

not provide correct polarity, the ignitor will

become grounded and click every once in

a while, even after the burner has ignited.

A qualified electrician should check the wall

receptacle to see if it is wired with correct

polarity.

10

Fire Hazard

Do not let the burner flame extend

beyond the edge of the pan.

Turn off all controls when not

cooking.

Failure to follow these instructions

can result in death or fire.

Burner heat settings

Use correct burner heat settings (see chart

later in this section). If the heat setting is too

high, it can:

• Char bacon and cause curling.

, Make eggs tough and crisp at the edges.

, Toughen liver, fish, and seafood.

, Scorch delicate sauces and custards.

• Cause a boilover.

Until you get used to the settings, use

the following as a guide.

SETTING RECOMMENDED USE

HI • To start food cooking.

• To bring liquid to a boil.

Between • To hold a rapid boil.

MED and • To quickly brown or

HI sear meat.

MED • To maintain a slow boil.

• To fry poultry or meat.

• To make pudding, sauce,

or gravy.

Between • To stew or steam food.

MED and

LO

LO • To simmer food.

• To keep food warm.

• To melt chocolate or butter.

!sing and Caring forYour Cooktop

In case of a prolonged power

failure

Surface burners can be manually lighted.

1. Hold a lit match near a burner and turn

the control knob to the HI position.

2. After the burner lights, turn the

control knob to the desired setting.

NOTE: Do not leave the cooktop unattend-

ed when cooking during a power failure.

The auto-reignition feature of your cooktop

will not operate during a power failure.

11

i:_iil_!_i:!i !sing and Caring for Your Cooktop

,(i,',iiiiiii:iii 0 0 WCIiiii 'iiiiiliii:ii:iiiiiii , i!! i;

Home canning information

The large diameter of most water-bath or

pressure canners combined with high heat

settings for long periods of time can cause

damage to the cooktop.

To protect your range:

* Center the canner over the surface burner.

Do not extend more than 1 inch (2.54 cm)

outside the burner area.

* Do not place your canner on two surface

burners at the same time.

* Start with hot water, cover with a lid and

bring to a boil; then reduce heat to main-

tain a boil or required pressure levels in a

pressure canner.

* Refer to your canner manual for specific

instructions.

For up-to-date information on canning, con-

tact your local U.S. Government Agricultural

Department Extension Office or companies

who manufacture home canning products.

Using the right cookware makes a

big difference

* The pan should have a flat bottom, straight

sides, and a well-fitting lid.

* Choose medium to heavy gauge

(thickness) cookware.

• The pan material (metal or glass) affects

how quickly and evenly the pan heats.

• When using glass or ceramic cookware,

check to make sure it is suitable for use on

surface burners.

• To avoid tipping, make sure pots and pans

are centered on the grates.

The pan material affects how fast heat transfers from the surface cooking area through the pan

material and how evenly heat spreads over the pan bottom. Choose pans that provide the

best cooking results.

Aluminum

Cast iron

• Heats quickly and evenly.

• Use for all types of cooking.

• Medium or heavy thickness is best for most cooking.

• Used as a core or base in cookware to provide even heating.

• Heats slowly and evenly.

• Good for browning and frying.

• Maintains heat for slow cooking.

• Can be coated with porcelain enamel.

Ceramic or • Heats slowly and unevenly.

ceramic glass • Use on low to medium settings.

• Follow manufacturer's instructions.

Copper • Heats very quickly and evenly.

• Used as a core or base in cookware to provide even heating.

Earthenware • Can be used for cooktop cooking if recommended by the

manufacturer.

• Use on low settings.

Porcelain enamel-on-steel • See cast iron and stainless steel.

or enamel-on-cast iron

Stainless steel

• Heats quickly but unevenly.

• A core or base of aluminum or copper on the cookware

provides even heating.

• Can be coated with porcelain enamel.

12

Jsing and Caring forYour Cooktop

,(iiiiii_i_i:_iiiii;i:_iii__!i_i'_"'_i!!iiiiiiiiiiiii'ii_0_iii''¸__,_,"_,_:,:::::::ii;_,,,_,,,,,_,i!ii"',C_,,0,0¸!if('!'_0,!i:i;i_,,

Your cooktop is designed for ease of care.

You can do most cleaning with items found

around the home. Cleaning your cooktop

whenever spills or soiling occur will help to

keep it looking and operating like new.

NOTES:

• Before cleaning make sure all controls

are off and the cooktop is cool.

• Do not obstruct the flow of combustion

and ventilation air.

• If knobs are removed while cleaning, be

careful not to spill liquids through holes in

the control area.

• Be careful not to allow moisture to collect

in control area. Moisture could cause igni-

tor switches to fail.

Surface burners

• The burner caps should be routinely re-

moved and cleaned. Always clean burner

caps after a spillover. Keeping the burner

caps clean prevents improper ignition and

an uneven flame.

• For proper flow of gas and ignition of the

burner, DO NOT ALLOW SPILLS, FOOD,

CLEANING AGENTS, OR ANY OTHER

MATERIAL TO ENTER THE GAS TUBE

OPENING.

• Occasionally check the burner flames for

proper size and shape as shown later in

this section. A good flame is blue in color.

If flames lift off ports, are yellow, or are

noisy when turned off, you may need to

clean the burners.

To clean burners and burner caps:

Burner cap

iiiii!ii!i!ii!i!ii!i!ii!i!ii!!

Gas tube

(orifice)

1. Lift the burner cap straight up from the

burner base.

2. Clean burner cap with warm, soapy water

and a sponge. For stubborn stains, clean

with a mildly abrasive plastic scrubbing

pad and powdered cleanser. Wipe dry. Do

not clean burner cap in dishwasher.

3. If the gas tube opening or the orifice,

located inside the opening, has become

soiled or clogged, use a cotton swab or

a soft cloth to clean the area.

4. If ports are clogged, clean with a

straight pin. Do not enlarge or distort

port. Do not leave anything stuck in

the ports.

5. After cleaning the gas tube opening and

ports, replace the burner cap. To re-

place burner cap, make sure cap is

properly aligned and leveled.

6. Check the burner after cleaning for proper

lighting.

NOTE: To check oven burner flames for

proper size and shape, see the Installation

Instructions also included with the range.

13

i_i_il_!_i:!iiii_ing and Caring forYour Cooktop

Adjusting the height of top burner

flames

The LO burner flame should be a steady

blue flame approximately 1/inch (6 mm)

high. It can be adjusted using the

adjustment screw in the center of the valve

stem. The valve stem is located directly

underneath the control knob.

To adjust the flame height follow the in-

structions below:

1. Turn the control knob to "LO."

2. Remove the control knob. (If there is not

an adjustment screw underneath the

knob the flame height is not adjustable.)

3. Hold the valve stem with a pair of pliers.

The screw is located in the center of the

valve stem. Use a small fiat head screw-

driver to turn the screw until the flame is

the proper size.

4. Replace the control knob.

........Adjustment screw

......... Valve stem

5. Test the flame by turning the control from

"LO" to "HI," checking the flame at each

setting,

Low flame

'_-_ !.n_l Ln_l Ln_l Ln_l I_rLI

High flame

Q-_ 'm_l t.n..! t.n..! t.n..! LnJ

o

14

, ingand Caring forYour Cooktop

Explosion Hazard

Do not store flammable materials such as gasoline near this

appliance.

Doing so can result in death, explosion, or fire.

PART

Control

knobs

Tempered

glass

surface

Surface

burner

grates

and caps*

WHAT TO USE HOW TO CLEAN

Sponge and warm,

soapy water

* Turn knobs to OFF and pull straight away from con-

trol panel.

* Wash, rinse, and dry thoroughly. Do not soak.

• Do not use steel wool or abrasive cleansers.

They may damage the finish of the knobs.

• Replace knobs. Make sure all knobs point to OFF.

Sponge and warm,

soapy water

OR

Paper towel and

spray glass cleaner

• Remove grates.

• Wash, wipe with clean water, and dry thoroughly.

• Use nonabrasive, plastic scrubbing pad on heavily

soiled areas.

• Do not use steel wool, abrasives, or harsh

cleansers. They may damage the finish.

• Ifyou use soap or detergent solutions, wipe

thoroughly to prevent filmy residue.

NOTE: When cleaning cooktop with knobs removed,

do not allow water to run down inside unit.

• Replace grates.

Warm, soapy water

and a mildly abrasive

plastic scrubbing pad

and/or powdered

cleanser

• Clean as soon as they become dirty and when they

are cool enough to handle.

• Wash with a mildly abrasive plastic scrubbing pad

and warm, soapy water.

• For stubborn stains, clean with a scrubbing pad

and/or a powdered cleanser and water. Repeat

these cleaning steps as needed.

• Do not put in oven during self-cleaning cycle.

• Do not clean in dishwasher.

Surface See "Caring for your cooktop" earlier in this section

burners for cleaning instructions.

When the cooktop is cool, remove all spills and clean. Food spills containing acids, such

as vinegar and tomato, may affect the finish.

15

i:_iil_!_/::!:ising and Caring for Your Cooktop

L,fsii_i"_"'ii_,{Tictii"'"_lcl

The surface light is in the backguard. It is

controlled by the Surface Light Command

Pads on the control panel. The ON

Command Pad turns on the light immediately

and keeps it on until you press OFF. The

NIGHT Command Pad will turn on the

surface light automatically when the light in

the room is low enough to require a night

light. When the night light comes on, it will

also dim all lights appearing on the display.

Press OFF to turn off the regular surface light

or press NIGHT again to turn off the night

light.

Replacing the surface light:

1. Unplug range or disconnect power.

2. Flip up the top of the backguard.

To turn on the surface light:

!:::!::i:iii!!!i!7!i:'::!

To turn off surface light:

3. Pull up glass on front of backguard.

To turn on night light:

"NIGHT LIGHT" shows on the display when

the night light is on.

To turn off night light:

4. Grasp the fluorescent light tube at both

ends. Turn the tube approximately 90°

in either direction until both ends come

out of the receptacles. Replace with a

20-watt cool-white fluorescent light tube.

16

ii_,_ingand Caring forYour Cooktop

5. If the surface light still does not work,

you may need to replace the starter. The

starter is a knob-shaped part located on

the right side of the backguard, under the

light tube.

ilJJiiiJiiJiiiii_

..... iJ i

I

/

To remove and replace the starter, first

remove light tube. Push starter in and

turn approximately 90° counterclockwise.

Pull starter out of recessed area. You

can find replacement starters at stores

that sell fluorescent light tubes.

6. Replace glass and close the top panel.

7. Plug in range or reconnect power.

17

• and Caring for Your

Oven

This section tells you, step by step, how to operate all oven functions controlled by the elec-

tronic control. Carefully follow these instructions, along with the cooking tips and cleaning

information, for successful use of your range.

Oven display

(see below)

(p. 26)

I

Oven EASY Convect Full Surface light Oven Timer

setting CONVECTTM Meal pad pads light pad pads

pads conversion (p. 43) (some freestanding (p. 57) (p. 27)

pads models only)

(p. 46) (p. 16)

Timed and

delayed Number Clock

cooking pads pads set/start Time of day/ Start

(pp. 48-51) pad timer display pad

Cancel/off

pad

Display/clock

• When you first plug in the range, a tone

will sound, the display will be fully lit for a

few seconds, and the display will show

the last time set and "PF" (power failure).

If, after you set the clock (See "Setting the

clock" later in this section), the display

again shows "PF," your electricity was off

for a while. Reset the clock.

• The time display will show "Err" and

3 short tones will sound if a time or

temperature is incorrectly entered.

NOTE: You have to hold down the pad a

short time to get it to work, and you have

to allow a short time between each pad

entry. If you press a command pad several

times, the pad can stop working. If you wait

a few seconds, you can use the pad again.

18

ii_,,_ingand Caring forYour Oven

Fahrenheit/Celsius

To set your oven to cook in Celsius instead

of Fahrenheit:

1. Open the door.

2. Press CANCEL/OFF.

CANCELI

3. Press the Number Pads 1, 2,

and 3, in that order.

4. Press BROIL.

5. Start oven.

NOTES:

• Press BAKE to confirm that you are

using Celsius.

• Only the temperature and a flashing

degree symbol will appear in the tem-

perature display area when you set

your oven to cook in Celsius.

Repeat the steps above to change

from Celsius to Fahrenheit.

19

;sing and Caring for Your Oven

If you need to convert temperatures from

Celsius to Fahrenheit or vice versa,

you can refer to this chart:

Temperature replacement values

38°C=100°F

60°C=140°F

66°C= 150°F

77°C= 170°F

93°C=200°F

121°C=250°F

135°C=275°F

149°C=300°F

163°C=325 °F

177°C=350 °F

191 °C=375°F

204°C=400°F

218 °C=425° F

232°C=450°F

246°C=475°F

260°C=500°F

Disable/enable audible signals

Audible signals tell you if a function is

entered correctly or not. They also tell

you when a cycle is completed. To turn

off key entry tone, end-of-cycle tone, and

reminder tones, follow these steps:

1. Open the door.

2. Press CANCEL/OFF.

ICANCEL

20

La page charge ...

KitchenAid KGRT507GBS0 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KGRT507GBS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents