Dometic FlyTec FT100 Mode d'emploi

FlyTec FT100

Flyscreen for sliding doors

Installation and Operating Manual. . . . . . . . 9

Insektenschutz für Schiebetüren

Montage- und Bedienungsanleitung . . . . . 18

Moustiquaire pour portes

coulissantes

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . . .28

Protección contra insectos para

puertas corredizas

Instrucciones de montaje y de uso . . . . . . .38

Proteção contra insetos para portas

deslizantes

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Zanzariera per porte scorrevoli

Istruzioni di montaggio e d’uso . . . . . . . . .57

Hor voor schuifdeuren

Montagehandleiding en

gebruiksaanwijzing. . . . . . . . . . . . . . . . . . . 67

Net til skydedøre

Monterings- og betjeningsvejledning. . . . 77

Insektsskydd för skjutdörrar

Monterings- och bruksanvisning . . . . . . . . 86

Insektsbeskyttelse for skyvedører

Monterings- og bruksanvisning . . . . . . . . . 96

Hyttyssuoja liukuoviin

Asennus- ja käyttöohje . . . . . . . . . . . . . . . 105

Москитная сетка для сдвижных

дверей

Инструкция по монтажу и эксплуатации 114

Ochrona przed insektami dla drzwi

przesuwnych

Instrukcja montażu i obsługi. . . . . . . . . . . 124

Protihmyzová sieťka pre posuvné

dvere

Návod na montáž a uvedenie

do prevádzky. . . . . . . . . . . . . . . . . . . . . . . 133

Síť proti hmyzu na posuvné dveře

Návod k montáži a obsluze . . . . . . . . . . . 142

Rovarvédő tolóajtókhoz

Szerelési és használati útmutató . . . . . . . 151

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

WINDOWS & DOORS

BLINDS

FT100-IO-16s.book Seite 1 Montag, 3. April 2017 6:37 18

FT100-IO-16s.book Seite 2 Montag, 3. April 2017 6:37 18

FlyTec FT100

3

5

4

1

10

2

6

7

8

9

1

C = 15 mm

A =

18 mm

B = 3 mm

5

4

3

2

40 mm

1

Y

X

2

FT100-IO-16s.book Seite 3 Montag, 3. April 2017 6:37 18

FlyTec FT100

4

1

3

1.

4.

3.

2.

4

FT100-IO-16s.book Seite 4 Montag, 3. April 2017 6:37 18

FlyTec FT100

5

1.

2.

3.

6

FT100-IO-16s.book Seite 5 Montag, 3. April 2017 6:37 18

FlyTec FT100

6

7

2.

1.

8

1.

2.

9

FT100-IO-16s.book Seite 6 Montag, 3. April 2017 6:37 18

FlyTec FT100

7

7x

0

1

2

1.

3.

2.

4.

a

FT100-IO-16s.book Seite 7 Montag, 3. April 2017 6:37 18

FlyTec FT100

8

b

FT100-IO-16s.book Seite 8 Montag, 3. April 2017 6:37 18

EN

FlyTec FT100

9

Please read this instruction manual carefully before installation and first

use, and store it in a safe place. If you pass on the product to another

person, hand over this instruction manual along with it.

Contents

1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Installing the flyscreen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6 Using the flyscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

7 Cleaning and maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

8 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

9 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

10 Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

FT100-IO-16s.book Seite 9 Montag, 3. April 2017 6:37 18

EN

Explanation of symbols FlyTec FT100

10

1 Explanation of symbols

A

I

2 Safety instructions

Please observe the safety instructions and stipulations issued by the vehicle manufac-

turer and service workshops.

The manufacturer accepts no liability for damage in the following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical influences

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in the operating manual

A

NOTICE!

• If you do not have sufficient technical knowledge for installing compo-

nents in vehicles, you should have a specialist install the flyscreen in

your vehicle.

• Check whether the dimensions of the flyscreen fit your vehicle.

• Installation of the flyscreen requires two people.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

FT100-IO-16s.book Seite 10 Montag, 3. April 2017 6:37 18

EN

FlyTec FT100 Scope of delivery

11

3Scope of delivery

The screws for fastening on the vehicle are not included in the scope of delivery.

4 Intended use

The Dometic FlyTec FT100 is a flyscreen for sliding doors on camper vans which can

be slid or folded horizontally. For available versions see the table, page 17.

No. in

fig. 1,

page 3

Quantity Description

1 1 Skirting board

2 1 Cassette profile with flyscreen and guide cables

3 1 C pillar cover

4 7 Blind rivet (4 x 8 mm with stainless steel mandrel)

5 1 Fastening screw M5 x 30 mm and M5 nut

6 1 Guide rail above

7 1 Safety clip and screw M2.5 x 6

8 1 Magnetic plate with double-sided tape

9 1 B pillar cover

10 1 Deflection screw M4 with safety clip and screw M2.5 x 6

– Installation and operating manual

FT100-IO-16s.book Seite 11 Montag, 3. April 2017 6:37 18

EN

Installing the flyscreen FlyTec FT100

12

5 Installing the flyscreen

5.1 Notes on installation

• Before installing the flyscreen, check whether any vehicle components could be

damaged by the installation of the flyscreen (such as cupboards).

• For safety reasons, note the location of existing wiring harnesses, wires and other

components within the installation area, in particular those which are not visible,

when installing the flyscreen (when drilling or screwing, etc.).

5.2 Preparing the vehicle

Measuring the opening (fig. 2, page 3)

Please observe the following instructions when measuring:

• The installation opening should not have been made smaller through added

strips, coverings, fixtures, etc.

• The installation opening must have the minimum width of X and minimum height

of Y:

• Behind the rear sealing of the door (1), there needs to be a minimum of 40 mm

space for the flyscreen to be installed.

• There needs to be a space with a width of A = 18 mm between the outer edge of

the bodywork floor (4) and fitted cabinets (2) (e.g. kitchen).

• The skirting board (5) needs the following space:

– There needs to be a space with a width of A = 18 mm between the outer edge

of the bodywork floor (4) and the edge of the interior fittings base (3).

– A space with a height of B = 3 mm and a depth of C = 15 mm needs to be

available from the edge of the interior fittings base (3).

You may need to adapt fitted cabinets (2) and the interior fittings base (3).

• The flyscreen must be screwed directly to the sheet-metal bodywork at the top

and bottom and not just on the panelling or the interior fittings. It is usually

sufficient to screw it on to the base of the interior fittings.

FlyTec version (ref. no.) Minimum width X Minimum height Y

9104114006 and 9104115153 1298 mm 1765 mm

9104115154 and 9104115155 1128 mm 1492 mm

FT100-IO-16s.book Seite 12 Montag, 3. April 2017 6:37 18

EN

FlyTec FT100 Installing the flyscreen

13

➤ Measure the installation opening in your vehicle and check whether the

dimensions of the flyscreen fit your vehicle.

➤ Remove the rubber buffer from the door (fig. 3, page 4).

Trimming the opening (depending on the vehicle)

➤ If necessary, remove add-on parts that interfere (such as bottom end strips or

bodywork) in the installation opening.

To be able to install the skirting board (fig. 1 1, page 3) flush, you may need to trim

the existing fixtures (such as floors or cabinets).

➤ Mark the following (fig. 2, page 3):

– Size A = 18 mm (width of the bottom part of the skirting board), measured

from the edge of the sheet-metal bodywork

– Size B = 3 mm (height of the skirting board).

➤ If necessary, trim the existing fixtures with a suitable tool, such as an oscillating

saw.

➤ Smooth and clean the cut edges.

5.3 Pre-installing the rails

Cassette profile, skirting board and upper guide rail

The cassette profile, skirting board and upper guide rail must be assembled lying on

the ground (fig. 4, page 4) before being placed in the vehicle.

➤ Check whether the cover profile can be inserted between the C pillar and interior

fittings. You may need to adapt the contour by trimming.

➤ Guide the lower slider of the handle strip along with the cassette profile into the

skirting board.

➤ Pull the cassette and handle strip apart by a bit and then slide the cassette profile

onto the nose on the skirting board.

➤ Secure the cassette profile with the screw (M5 x 30 mm) and M5 nut on the upper

guide rail.

➤ Insert the cover for the C pillar into the cassette so that the drill holes are located

one above the other and secure the two components with three blind rivets

(4 x 8 mm with stainless steel mandrel) without riveting them (fig. 5, page 5).

➤ Secure the deflection screw M4 (fig. 6 1, page 5) to the skirting board.

FT100-IO-16s.book Seite 13 Montag, 3. April 2017 6:37 18

EN

Installing the flyscreen FlyTec FT100

14

➤ Fit the guide cables into the bottom and top deflection screw (fig. 6 2 and 3.

page 5).

➤ Have two people carefully lift the pre-assembled flyscreen and position it in the

vehicle.

Adjusting the top guide rail

➤ Check whether the contour and position of the upper guide rail fit the vehicle

(see enlarged inset in fig. 8, page 6). You may need to adjust the upper guide

rail by cutting the two upper legs.

5.4 Securing the flyscreen in the vehicle

A

Securing the skirting board and upper guide rail

➤ Align the position of the cassette profile perpendicular to the skirting board and

the upper guide rail.

➤ Secure the skirting board to the bottom plate (fig. 7, page 6) with four counter-

sunk screws (Ø 4 mm).

➤ Secure the upper guide rail to the vehicle (fig. 8, page 6) with four countersunk

screws (Ø 4 mm).

Installing the cover on the B pillar (fig. 9, page 6)

A

➤ Put the cover on the B pillar so that it is flush on all sides.

➤ Align the cover on the bottom of the skirting board and mark the drill holes.

➤ Pre-drill at the marked points if the wall construction requires this.

➤ Secure the cover on the B pillar with five countersunk screws (Ø 4 mm).

NOTICE!

• Choose suitable screws depending on the floor and roof

construction.

• Make sure that you do not drill through the floor and roof.

NOTICE!

• Depending on the type of vehicle, the spacers behind the cover

must be adapted to the correct length.

• The contour of the cover may need to be adapted to the interior

fittings in the upper and lower area.

• It may also be necessary to adapt the interior fittings.

FT100-IO-16s.book Seite 14 Montag, 3. April 2017 6:37 18

EN

FlyTec FT100 Installing the flyscreen

15

Installing the magnetic plate (fig. 9, page 6)

A

➤ Glue on the magnetic plate.

5.5 Completing installation

Riveting the cassette profile with the cover profile for the C pillar (fig. 0,

page 7)

➤ Put all the blind rivets (4 x 8 mm with stainless steel mandrel) through the drill

holes and rivet the components using a hand riveter.

Tensioning the guide cables

➤ Tension the guide cables on the deflection screws on the skirting board and the

top guide rail (fig. a, page 7).

The tension of the cables affects the guidance and smooth running of the handle

strip. By changing the tension of the upper and lower cable, you can adjust the

parallel orientation of the handle strip to the magnetic plate.

➤ Secure the safety clips onto the deflection screws each with a screw

(M2.5 x 6 mm) (fig. a 1 and 2, page 7).

NOTICE!

• The adhesion points must be clean, dry and free of grease in order

for the magnetic plate to adhere well to the cover profile.

• Clean the adhesive surface with a suitable cleaner. It may be

necessary to check suitability on a hidden spot.

• Use lint-free cloths.

FT100-IO-16s.book Seite 15 Montag, 3. April 2017 6:37 18

EN

Using the flyscreen FlyTec FT100

16

6 Using the flyscreen

A

Closing the flyscreen

➤ Pull the handle strip on the flyscreen to close the flyscreen (fig. b, page 8).

✓ The magnetic plate holds the flyscreen closed.

Opening the flyscreen

➤ Pull the handle strip on the flyscreen to open the flyscreen (fig. b, page 8).

7 Cleaning and maintenance

A

➤ Occasionally clean the product with a damp cloth.

➤ Spray the guide rails on the sliding surfaces periodically with small amounts of

silicone spray to achieve the easiest possible sliding of the cassette profile in the

guide rails.

8Warranty

The statutory warranty period applies. If the product is defective, please contact the

service partner in your country (addresses on the back on the instruction manual).

Our experts will be happy to help you and will discuss the warranty process with you

in more detail.

NOTICE! Beware of damage!

The sliding door of the vehicle may be closed only when the flyscreen is

fully open.

NOTICE!

Do not use sharp or hard objects or cleaning agents for cleaning as these

may damage the product.

FT100-IO-16s.book Seite 16 Montag, 3. April 2017 6:37 18

EN

FlyTec FT100 Disposal

17

9Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever

possible.

M

If you wish to finally dispose of the product, ask your local recycling centre

or specialist dealer for details about how to do this in accordance with the

applicable disposal regulations.

10 Versions

Version Dimensions Ref. no.

Version in direction of travel on the right for Fiat

Ducato, Citroën Jumper, Peugeot Boxer from model

year 2006, higher version

1298 x 1765 mm 9104114006

Version in direction of travel on the left for Fiat

Ducato, Citroën Jumper, Peugeot Boxer from model

year 2006, higher version

1298 x 1765 mm 9104115153

Version in direction of travel on the right for Fiat

Ducato, Citroën Jumper, Peugeot Boxer from model

year 2006, lower version

1128 x 1492 mm 9104115154

Version in direction of travel on the left for Fiat

Ducato, Citroën Jumper, Peugeot Boxer from model

year 2006, lower version

1128 x 1492 mm 9104115155

FT100-IO-16s.book Seite 17 Montag, 3. April 2017 6:37 18

DE

FlyTec FT100

18

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig

durch und bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe

des Produktes an den Nutzer weiter.

Inhalt

1 Erklärung der Symbole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

2 Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

5 Insektenschutz montieren. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

6 Insektenschutz benutzen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

7 Reinigung und Pflege . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

8 Gewährleistung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

9 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

10 Versionen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

FT100-IO-16s.book Seite 18 Montag, 3. April 2017 6:37 18

DE

FlyTec FT100 Erklärung der Symbole

19

1 Erklärung der Symbole

A

I

2 Sicherheitshinweise

Beachten Sie die vom Fahrzeughersteller und vom Kfz-Handwerk vorgeschriebenen

Sicherheitshinweise und Auflagen!

Der Hersteller übernimmt in folgenden Fällen keine Haftung für Schäden:

• Montage- oder Anschlussfehler

• Beschädigungen am Produkt durch mechanische Einflüsse

• Veränderungen am Produkt ohne ausdrückliche Genehmigung vom Hersteller

• Verwendung für andere als die in der Anleitung beschriebenen Zwecke

A

ACHTUNG!

• Wenn Sie nicht über ausreichende technische Kenntnisse zum Ein-

bauen von Komponenten in Fahrzeugen verfügen, sollten Sie sich den

Insektenschutz von einem Fachmann ins Fahrzeug einbauen lassen.

• Prüfen Sie, ob die Abmessungen des Insektenschutzes zu Ihrem Fahr-

zeug passen.

• Die Montage des Insektenschutzes erfordert zwei Personen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des

Produktes beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

FT100-IO-16s.book Seite 19 Montag, 3. April 2017 6:37 18

DE

Lieferumfang FlyTec FT100

20

3 Lieferumfang

Die Schrauben für die fahrzeugseitige Befestigung sind nicht im Lieferumfang

enthalten.

4 Bestimmungsgemäßer Gebrauch

Dometic FlyTec FT100 ist ein horizontal verschiebbarer, faltbarer Insektenschutz für

Schiebetüren von Campingbussen. Verfügbare Versionen siehe Tabelle, Seite 27.

Pos. in

Abb. 1,

Seite 3

Anzahl Beschreibung

1 1 Trittleiste

2 1 Kassettenprofil mit Fliegengaze und Führungsseilen

3 1 Abdeckprofil C-Säule

4 7 Blindniete (4 x 8 mm mit VA-Dorn)

5 1 Befestigungsschraube M5 x30 mm und Mutter M5

6 1 Führungsschiene oben

7 1 Sicherungsbügel und Schraube M2,5 x 6

8 1 Magnetblech mit doppelseitigem Klebeband

9 1 Abdeckung B-Säule

10 1 Umlenkschraube M4 mit Sicherungsbügel und

Schraube M2,5 x 6

– Montage- und Bedienungsanleitung

FT100-IO-16s.book Seite 20 Montag, 3. April 2017 6:37 18

La page charge ...

Dometic FlyTec FT100 Mode d'emploi

Dometic FlyTec FT100 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents