Breville the Breville Precision Brewer Thermal Manuel utilisateur

Catégorie
Accessoires de préparation de café
Taper
Manuel utilisateur
the Breville
Precision Brewer
Thermal
Instruction Book - BDC450/BDC455
BDC450_455_USC_IB_I20_FA.indd 1 24/1/20 9:48 am
2
BREVILLE
RECOMMENDS
SAFETY FIRST
At Breville we are very safety
conscious. We design and
manufacture consumer
products with the safety of you,
our valued customer, foremost
in mind. In addition we ask
that you exercise a degree of
care when using any electrical
appliance and adhere to the
following precautions.
IMPORTANT
SAFEGUARDS
READ ALL
INSTRUCTIONS BEFORE
USE AND SAVE FOR
FUTURE REFERENCE
Carefully read all
instructions before
operating the appliance and
save for future reference.
Remove and safely discard
any packaging material,
plastic power plug cover,
and any removable labels
before using appliance.
If the appliance is to be:
left unattended
cleaned
moved
assembled; or
stored
unplug the unit from the
power outlet.
Always operate the
appliance on a stable and
heat resistant surface.
Do not place the appliance
on or near a hot gas burner,
electric element or where it
could touch a heated oven.
2 Breville recommends safety first
8 Components
10 Features
10 Assembly
11 Operation
15 Programming
16 Tips
19 Care & Cleaning
20 Troubleshooting
23 French
Contents
BDC450_455_USC_IB_I20_FA.indd 2 24/1/20 9:48 am
3
Ensure the unit has at
least 4 inches (10cm)
of clearance from all
side panels.
Do not operate the
appliance without water
in the water tank. Use
only cold, preferably
filtered water. Do not
fill the appliance with
any other liquids for
brewing operations.
Ensure the supplied mesh
basket filter or a paper filter
(8-12 cup, flat base basket
style with ~ 3¼"/8.25cm
base) is placed in the
coffee basket before
using the appliance. Do
not use the mesh basket
filter in conjunction with
a paper filter.
Before starting a brew cycle:
Check that the carafe
drip stop moves up and
down freely.
Completely empty the
carafe and securely lock
the carafe lid in place.
Insert and seat the carafe
under the drip stop.
Ensure the filter basket
is empty and properly fit
in place.
During a brew cycle:
Do not remove the carafe
or remove the filter basket
while the unit is in a brew
cycle. Failure to follow the
above may lead to scalding
or serious injury.
Some surfaces may be hot,
use caution when touching
or lifting the unit or
accessories.
Use only carafe handle
when lifting the carafe.
The carafe is designed for
use with this appliance only.
It must never be used on a
range top or in a microwave.
Scalding may occur if
the carafe lid or basket
is removed during the
brewing cycle.
CAUTION
Risk of injury. Proper
installation/removal of
basket is required to reduce
the risk of splashing of
hot water.
BDC450_455_USC_IB_I20_FA.indd 3 24/1/20 9:48 am
4
Always ensure the carafe
lid is securely locked
in place onto the carafe
before pouring.
Do not use the carafe with a
cracked, loose, weakened or
damaged handle.
Do not use the filter
basket with a cracked,
loose, weakened or
damaged handle.
Do not touch hot surfaces.
Use the handle for lifting
and carrying the carafe.
Always wait until the
machine has cooled before
removing the brew basket.
Do not set a hot carafe
on a wet, cold or heat
sensitive surface.
Unplug from outlet when
the appliance or the
display clock is not in use,
and before cleaning and
storing. Allow to cool before
putting on or taking off
parts, and before cleaning
the appliance.
Do not use harsh or
abrasive materials when
cleaning any part of this
appliance such as steel
wool or scoring pads.
The use of attachments
not sold or recommended
by Breville may cause fire,
electric shock or injuries.
Scalding may occur if the
basket is removed during
the brewing cycles.
Proper installation of filter
basket, showerhead seal,
and showerhead locking
ring is required to reduce
the risk of splashing of
hot water.
CAUTION
To prevent damage to
the appliance do not use
alkaline cleaning agents
when cleaning, use a soft
cloth and a mild detergent.
The heating element
surface is subject to residual
heat after use.
The appliance shall not be
placed in a cabinet when
in use.
BDC450_455_USC_IB_I20_FA.indd 4 24/1/20 9:48 am
5
IMPORTANT
SAFEGUARDS
FOR ALL
ELECTRICAL
APPLIANCES
Fully unwind cord
before use.
To protect against fire,
electric shock, and injury to
persons, do not immerse
cord, plug or appliance in
water or any other liquid.
Do not let the cord hang
over the edge of a bench or
table, touch hot surfaces, or
become knotted.
Do not leave the appliance
unattended when in use.
Children should be
supervised to ensure
they do not play with the
appliance.
This appliance is
recommended for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors.
It is recommended to
regularly inspect the
appliance. Do not use the
appliance if the power
supply cord, power plug,
or appliance becomes
damaged in anyway.
Immediately stop using
the unit and call Breville
Consumer Support.
Close supervision is
necessary when the
appliance is used by or
near children.
CAUTION
We recommend using
cold, filtered water. We do
not recommend the use of
de-mineralized or distilled
water as this may affect the
taste of brewed coffee.
BDC450_455_USC_IB_I20_FA.indd 5 24/1/20 9:48 am
6
SHORT CORD
INSTRUCTIONS
Your Breville appliance is
fitted with a short power
cord to reduce the risk of
personal injury or property
damage resulting from
pulling, tripping or becoming
entangled with a longer cord.
Longer detachable power
cords or extension cords are
available and may be used
if care is exercised. If an
extension cord is used,
(1) the marked electrical
rating of the cord set or
extension cord should be at
least as great as the electrical
rating of the appliance, (2)
the cord should be arranged
so that it will not drape over
the counter-top or table
where it can be pulled on
by children or tripped over
unintentionally and (3) the
extension cord must include
a 3-prong grounding plug.
This appliance is not
intended for use by
persons (including
children) with reduced
physical, sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been
given supervision or
instruction concerning
use of the appliance by
a person responsible for
their safety.
This appliance can be
used by children aged
from 8 years and above
if they have been given
supervision or
instruction concerning
use of the appliance in
a safe way and if they
understand the hazards
involved. Cleaning and
user maintenance shall
not be made by children
unless they are older than
8 and supervised.
Keep the appliance and
its cord out of reach of
children aged less than
8 years.
BDC450_455_USC_IB_I20_FA.indd 6 24/1/20 9:48 am
7
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
NOTE
This appliance has a
three wire grounded
plug. To reduce the risk
of electric shock, this
plug will fit in a polarized
outlet only one way. If the
plug does not fit properly
into the outlet, contact a
qualified electrician.
Do not use an adaptor or
modify the plug in any
way. Do not connect the
appliance to an external
switch or device (such as
a timer, monitor or remote
circuit) that can be switched
on and off.
BREVILLE ASSIST
®
PLUG
Your Breville appliance
comes with a unique
Assist
®
Plug, conveniently
designed with a finger hole
to ease removal from the
power outlet.
CALIFORNIA
PROPOSITION 65:
(Applicable to California
residents only).
This product contains
chemicals known to the
State of California to cause
cancer, birth defects or other
reproductive harm.
BDC450_455_USC_IB_I20_FA.indd 7 24/1/20 9:48 am
8
A. Tank lid
B. Water tank
C. LCD display
D. SELECT dial
E. START|CANCEL button
F. AUTO START button
G. Brew basket
H. Showerhead
I. Showerhead ring
J. Drip stop lever
K. Carafe lid
L. Carafe
Components
B
H
I
C
D
E
F
A
G
J
K
L
BDC450_455_USC_IB_I20_FA.indd 8 24/1/20 9:48 am
9
A
D
E
F
G
*
B
C
A. Cone filter basket insert
B. Mesh basket filter
C. Brew basket
D. Breville coffee measuring scoop
E. Flat bottom basket filter paper pack (10 pieces)
F. Water hardness test strip
(see page 11 for directions)
G. Pour over adapter kit
ACCESSORIES
* Included in BDC455 or sold separately
*
BDC450_455_USC_IB_I20_FA.indd 9 24/1/20 9:48 am
10
Your Breville Precision Brewer has been
designed to make coffee of the highest quality,
just the way you like it, no matter what style of
coffee you enjoy.
Fast: Brew up to 12 cups (60oz) as fast as the
brewer can deliver the water in the tank.
Gold: This mode has been certified by the SCA
(Specialty Coffee Association) to meet their
rigorous technical requirements using the Cone
Filter Basket and water volumes of 1.0L
& 1.2L together with a brew ratio of 55g of coffee
to 1.0L of water.
Strong: Brew settings are automatically adjusted
so you get a stronger cup of coffee. Tip: for
strong coffee, increase the amount of ground
coffee you normally use.
Over Ice: Brew up to 4 cups (20oz) of stronger
coffee that tastes great when poured over ice
and garnished any way you like.
MyBrew: Brew up to 12 cups (60oz) having
total control over all the variables, brew water
temperature, bloom time, water delivery speed,
so you get coffee just the way you like it.
Cold Brew: Brew up to 20oz of Cold Brew
coffee with the flexibility to adjust steeping
time between 0-24 hours and have the coffee
automatically delivered into your favorite vessel.
SCA CERTIFIED
HOME BREWER LOGO
The SCA recognizes home brewers that
meet their longstanding rigorous technical
requirements. These requirements are based on
decades of industry knowledge and research by
the Coffee Brewing Center.
All SCA Certified Home Brewers have met these
requirements, which are based generally on
proper water temperature, brewing time, and
ability to brew within the SCA Golden
Cup recommendations.
If a brewer passes all of the tests in the
certification procedure, as conducted by
the SCA, that brewer will be eligible to be
Features
Assembly
BEFORE FIRST USE
Unpack all parts and accessories before
removing and safely discarding all packaging
material and promotional labels. Ensure the
power cord is unplugged from the power outlet.
Wipe the exterior stainless steel housing with
a soft, damp cloth. Wash the lid, brew basket,
cone filter insert, mesh basket filter, and carafe
in warm, soapy water and a soft cloth. Do not
use abrasive cleansers, pads or cloths which can
scratch the surface. Rinse and dry thoroughly.
Press carafe drip stop ensuring it can freely move
up and down.
NOTE
IMPORTANT NOTE ON WATER
HARDNESS
Water quality varies in each household. It is
important to check the water hardness level in
your home before using your machine for the first
time. If the water that you use for brewing coffee
is hard, the machine requires descaling on a more
regular basis. You can test the water hardness
using the test strip provided (included in the
package) and select the right hardness level of
water as shown in your water test strip result.
recognized as an exemplary home brewer
and join the short list of SCA Certified
Home Brewers.
The Breville Precision Brewer has met these
SCA requirements when using the "Gold"
setting and the Cone Filter basket.
BDC450_455_USC_IB_I20_FA.indd 10 24/1/20 9:48 am
11
Operation
BREWING A CARAFE
Ensure the brew basket is clean and the drip
stop seal in the bottom of the basket is clean
and free of coffee particles.
1. Select the correct basket & filter for the
amount of coffee you’re making. When
brewing between 2 and 8 cups, we
recommend you use the Cone shaped filter
basket insert with paper filter (Cone paper
filter is not included). When brewing more
than 8 cups, use mesh basket filter or flat
bottom brew basket with large paper filter.
2 - 8
CUPS
OR OR
8+
CUPS
CAUTION
Filling the basket without a mesh basket filter
or filter paper may cause the basket to overflow
during the brewing cycle.
2. The LCD will display the basket setting -
"Basket" or "Cone". To change the basket
type, rotate the SELECT dial to Settings &
press the dial. Rotate the SELECT dial to the
basket type, press the SELECT dial to set.
3. Fill the water tank with fresh cold water up
to the MAX marking on the water tank.
Setting the water hardness level in your
machine can prevent scale build-up.
Scale build-up can affect the brewing flow of the
machine, the brewing temperature and the taste
of the coffee.
Again, to ensure good coffee results, it is
important to select the right water hardness
level before brewing coffee for the first time.
Follow the steps below:
WATER HARDNESS SETTING AND
FLUSHING FOR FIRST TIME USE
1. Ensure that the empty coffee basket and
empty carafe (with assembled lid) are
inserted into the machine.
2. Fill the water tank with fresh cold water to
the MAX mark on the water tank. Plug into
power outlet.
3. When first turned on, the machine will
show 'HARD' on LCD, asking for the water
hardness level (refer to important note
above). Press SELECT dial once. Dip the
water hardness test strip into the filled
water tank for 1 second, remove and wait
for 1 minute to reveal the result. Rotate
SELECT dial and press the dial to select
the level according to the number of red
dots shown on the strip. To reset water
hardness, please refer to FACTORY RESET
(page 19).
4. The machine will show ‘FLUSH Unit’
on LCD. Press SELECT dial once. The
machine will dispense all the water from
the tank, through the system & into the
empty carafe. After flushing, empty the
basket and carafe.
BDC450_455_USC_IB_I20_FA.indd 11 24/1/20 9:48 am
12
NOTE
Coffee with superior taste & clarity will come
from using a paper filter.
NOTE
The mesh basket filter will allow some fine
coffee grounds to brew into the coffee. This
will appear as sediment in the cup or carafe.
This is normal. Only use the mesh basket filter
provided as others may cause the machine
to overflow.
7. Lock the carafe lid and place the carafe
under the drip stop outlet.
A
L
I
G
N
A
R
R
O
W
S
T
U
R
N
T
O
P
O
U
R
CAUTION
The carafe MUST be in place before you brew
with water level higher than ‘SINGLE CUP’
line. Otherwise the coffee basket will overflow.
NOTE
Always ensure your carafe is clean and empty
before brewing. Residual coffee will affect the
taste and liquid in the carafe will cause it to
overflow.
NOTE
Always ensure your carafe is EMPTY before
brewing to prevent overflow.
NOTE
This machine will brew all the water in the tank.
Ensure the tank does not contain an excess
amount of water.
4. For the very best tasting coffee, we
recommend using freshly roasted whole
bean coffee and grind with a burr grinder
directly before you brew. The grind should
be medium/coarse, never use coffee
ground for espresso as your coffee basket
may overflow.
5. Grind enough coffee beans for the volume
you’re making. For a full 60oz carafe,
we recommend 3.5oz (99g) of coffee,
approximately 12 level Breville measuring
scoops. Roughly 1 scoop for every 5oz.
Refer coffee/water ratio chart on page 16.
6. Insert the correct filter paper, cone or flat
bottom, or mesh basket, into the brew
basket, then, add your ground coffee. Insert
the brew basket into the machine.
NOTE
Never use both mesh basket filter and paper
filter at the same time.
BDC450_455_USC_IB_I20_FA.indd 12 24/1/20 9:48 am
13
Bloom Time: Coffee bloom occurs when
hot water hits the ground coffee. This
setting allows you to adjust how long the
bloom time lasts. We recommend 30-60
seconds. During this time the brewing cycle
pauses to allow coffee to naturally bloom.
See ‘TIPS’ for more about Bloom Time.
Brewing Temp: You can adjust the
temperature of the brew water being
delivered to the ground coffee to suit
your favorite coffee. See “TIPS” for more
about setting brew water temperature.
Flow Rate: You can adjust brewing time
to control contact time by adjusting the
water delivery speed. Choose between
Slow, Medium, and Fast (default).
Pour Over: If you are using the Pour
Over Adapter, this must be turned on.
(Included in BDC455 only. Sold separately
at Breville webpage).
OVER ICE: This is to make stronger coffee
for ice coffee.
Fill the water tank with the amount
of water you want to brew up to 20oz
line and start brewing. After brewing,
pour over ice. See ‘TIPS’ for details.
COLD BREW: Cold Brew coffee is brewed
differently to traditional coffee. It uses cold,
not hot water. Your brewer uses the “Full
Immersion” method of brewing cold brew
which steeps the water and coffee together
over an extended duration – typically
between 4 - 14 hours. This method creates an
intense smooth coffee with little bitterness.
Brew ratios are also different, and much
higher than normal. Breville recommends
a brew ratio 2-3 times higher than average,
approximately 3 Breville scoops to every 5oz
of water.
See ‘TIPS’ for step-by-step guide
of brewing Cold Brew.
Brew time is adjustable.
NOTE
OVER ICE mode and COLD BREW mode will
be disabled if there is more than 20oz of water
in the tank.
8. Rotate the SELECT dial to the desired
mode. Press the START|CANCEL button.
The machine will display the progress:
The machine will remind you to insert
either cup or carafe where applicable
Heating: the heating system is being
pre-heated to the optimal temperature
Blooming: the bloom phase of
preparation is in progress
Brewing: brew water at the correct/
selected temperature is being
delivered to the ground coffee
9. When your coffee is ready, the machine will
beep 3 times. The machine will display the
“Time since brewed”.
NOTE
A small amount of water remains in the
tank after brewing. This is part of the
normal operation.
NOTE
Never fill the water tank once the coffee
machine has started a brewing cycle.
BREW MODES
FAST: This mode is to deliver the fastest
brewed coffee. This coffee machine is one
of the fastest 12 cup (60oz) brewers.
GOLD (recommended): This mode has
been certified by the SCA (Specialty Coffee
Association) to meet their rigorous technical
requirements using the cone filter basket.
STRONG: This brewing mode delivers a
stronger tasting coffee.
MY BREW: Allows you to customize every
brew setting.
BDC450_455_USC_IB_I20_FA.indd 13 24/1/20 9:48 am
14
NOTE
DO NOT fill the water tank more than
SINGLE CUP line or the volume of the cup
used to receive the coffee. It will overflow as
the machine brews until the water tank
becomes empty.
2. Place your empty cup underneath the
brew basket outlet.
3. We recommend using cone filter basket
insert for single cups. It ensures proper
contact between the brew water and the
ground coffee.
4. To change the basket type, rotate the
SELECT dial to Settings and press to enter
the Settings mode and select "Basket Type".
5. Rotate the dial to select “Cone”, and press
dial to select. “Cone” will be displayed on
the LCD.
6. Insert the Cone filter basket into the brew
basket. Use the alignment marks as a guide.
7. Place a cone shaped paper filter into the
cone filter basket.
8. Grind the correct amount of whole bean
coffee for the amount you are brewing.
1 level Breville scoop of ground coffee is
suitable for 5oz (150ml) of water.
9. Select desired brewing mode, Fast, Gold,
MyBrew or Strong.
10. Press START|CANCEL to begin brewing.
SINGLE CUP/SMALLER VOLUMES
(LESS THAN 4 CUPS, 20OZ)
1. Your Breville Precision Brewer will
recognize when the brewer has less than
4 cups (20oz) of water & will adjust the
brew settings, automatically, to make
the best possible tasting coffee. Fill your
cup with fresh cold water and then pour it
into the water tank, ensuring the water
level stays below the SINGLE CUP line.
BDC450_455_USC_IB_I20_FA.indd 14 24/1/20 9:48 am
15
Programming
AUTO START
Allows you to automatically start brewing at
preset time.
1. Set filter basket type for the amount of coffee
you're brewing.
2. Select your brewing mode.
3. Fill the water tank with enough fresh cold
water for the amount of coffee you're brewing.
4. Insert the brew basket with your desired
insert or paper filter and add coffee.
5. Insert the appropriate cup or the carafe with
the lid locked in place into the machine.
6. Press the AUTO START button.
FAST
GOLD
SET CLOCK STANDBY
KEEP WARM
EXIT
DESCALE
SOUND
SETTINGS
COLD BREW
MYBREW
POUROVER
STRONG
BLOOM TIME
BLOOM VOL.
BREW TEMP.
FLOW RATE
CUSTOMIZE
CARAFE LID
REMOVE
FILL
AUTO START
TANK!
TIME SINCE BREW
MIN
HEATING BLOOMING BREWING
AM
PM
HR
MAX
AT
7. The machine will prompt you to set the
time for Auto Start. Rotate the SELECT dial
to adjust Auto Start time press SELECT
dial to set. Auto Start is now set and the
machine will enter Auto Start mode, brewing
automatically at the set Auto Start time.
NOTE
If the clock hasn’t been set, the machine will
prompt you to set the clock. Ensure the clock is
correct. The clock will reset every time the unit
is unplugged.
8. Pressing START|CANCEL will cancel
Auto Start.
SETTINGS
SET CLOCK: Set the time displayed on LCD.
SOUND: Sound volume is adjustable and also
can be turned off.
STANDBY: Adjust time to automatically enter
STANDBY mode after a period of no use.
FILTER TYPE: Factory setting is Flat basket,
adjustable when using the Cone filter
basket insert.
ENTERING STANDBY MODE
AT ANY TIME
Press the START|CANCEL button for
3 seconds.
DEGREE INDICATION PREFERENCE
(°C/°F)
To switch between °F and °C, press SELECT
dial and AUTO START button together. Rotate
SELECT dial to select, then press SELECT dial
to set.
CHILD-LOCK
To prevent children from possible danger,
child-lock feature is available. Press and hold
AUTO START button for 5 seconds. LCD will
display “CL” when it is locked. Repeat this again
or unplug the unit to unlock.
BDC450_455_USC_IB_I20_FA.indd 15 24/1/20 9:48 am
16
Tips
WHOLE BEANS
FRESH IS BEST! Freshly roasted, quality
coffee is key to making great tasting coffee.
Peak flavor potential is 5-20 days after roast.
Always look for a “Roasted On” date on the
bag. Avoid coffee with a “Best Before” or
“Use By” date as you never know when it
was roasted.
Coffee flavor and strength are a personal
preference. Vary the type of coffee beans and
the amount of ground coffee to achieve your
preferred taste.
Freshly ground beans are the key to making
coffee with more flavor and body. Pre-ground
coffee will have lost most of its flavor and
aromatics, so always grind right before you
brew for superior taste.
Store coffee beans in a dark, cool and dry
place. Vacuum seal if possible.
Buy coffee beans in small batches to reduce
the storage time and store no more than one
week’s supply at any time.
COFFEE/WATER RATIO
We recommend 1 level Breville scoop of coffee grounds per 5oz (150ml) cup of water. Adjust the
amount according to your individual taste. The maximum capacity for pre-ground coffee is 12 level
Breville scoops. Exceeding this amount may cause the coffee basket to overflow.
Cups of coffee
(5oz/150ml cup)
1 2 3 4 5 6 7* 8* 9 10 11 12
Spoons of coffee
grinds
1
(0.3oz /
8.25g)
2
(0.6oz /
16.5g)
3
(0.9oz /
24.75g)
4
(1.2oz /
33g)
5
(1.5oz /
41.25g)
6
(1.8oz /
49.5g)
7
(2.1oz /
57.75g)
8
(2.4oz /
66g)
9
(2.7oz /
74.25g)
10
(3oz /
82.5g)
11
(3.3oz /
90.75g)
12
(3.6oz /
99g)
Water amount
5oz /
150ml
10oz /
300ml
15oz /
450ml
20oz /
600ml
25oz /
750ml
30oz /
900ml
35oz /
1.05L
40oz /
1.2L
45oz /
1.35L
50oz /
1.5L
55oz /
1.65L
60oz /
1.8L
*SCA Certified using the Cone Filter.
PRE-GROUND COFFEE
Pre-ground coffee is convenient, but will
never taste as good as coffee ground right
before you brew. We recommend investing in
a quality burr grinder so you can grind fresh
whole bean coffee right before you brew and
enjoy superior tasting coffee.
The grind will affect the rate at which the
water flows through the coffee in the coffee
basket and therefore the taste of the coffee.
If the grind is too fine the water will not flow
through the coffee and may clog or overflow
the coffee basket. It may pass through the
mesh basket filter leaving sediment in the
cup or carafe. The resulting coffee will be
over extracted, too dark and bitter. If the
grind is too coarse the water will flow through
the coffee too quickly. This will result in an
under-extracted coffee lacking in flavor.
Always use “drip filter grind” suitable for
use with a drip coffee machines. Never use
“Espresso grind” as the finer grind size may
cause the coffee basket to block and will be
over-extracted.
BDC450_455_USC_IB_I20_FA.indd 16 24/1/20 9:48 am
17
BLOOMING
When coffee is roasted, CO
2
is trapped inside
the bean. Coffee grounds release this CO
2
when hot water hits them, and this is called
“blooming”. Your Brewer can automatically
adjust bloom time by controlling the water
flow. Blooming can have an impact on the
aromas and flavors of the brewed cup. If the
coffee is overly bitter shorten bloom time,
and if it’s sour make it a little longer.
PRE-HEATING
Pre-heat the carafe or cup for best results.
A pre-heated carafe or cup will help maintain
the coffee’s optimal temperature and keep
coffee hotter for longer. Fill with hot water for
about 30 seconds then discard the water.
WATER QUALITY
Fresh, good-tasting water is essential for a
perfect cup. If the water contains excessive
sediment, or has an ‘off’ taste or odor, we
recommend using filtered water.
ICED COFFEE
Iced coffee is at its best when the coffee is
brewed strong because the coffee is diluted
by the melting ice cubes. To achieve great
Iced coffee we recommend brewing in OVER
ICE mode. Fill the tank ensuring the water
level does not exceed the 20oz level.
Fill the brew basket with twice the
amount of coffee you'd normally use for
regular brewed coffee.
Brew into the carafe.
Once the brewing cycle is complete, transfer
the coffee to a heatproof pitcher and let cool
to room temperature. Refrigerate until cold,
at least 2 hours or overnight. Fill glasses with
ice cubes. Pour the coffee into the glasses,
filling them to within 1.5" (4cm) of the rim.
Top each glass with cream, milk, syrups or
sweeteners as desired.
NOTE
If using granulated sugar as a sweetener, add
while the coffee is hot to encourage the sugar
to completely dissolve.
To avoid a diluted taste, you can also use
regular strength coffee and serve it over
coffee ice cubes. Prepare coffee ice cubes
by pouring cool coffee into ice-cube trays
and freezing.
COLD BREW
Your Brewer will produce a maximum of
20oz of Cold Brew. Due to the long duration
(typically 4-14 hours) of the brewing process we
recommend setting the machine up overnight
so the Cold Brew will be ready in the morning.
1. Fill the tank with your desired volume of
water ensuring this is below the
COLD BREW line.
2. Remove the basket, and ensure both the
cone insert and mesh basket filter are
removed. Add a large paper filter and
then coffee at 2-3 times of regular ratio
(approximately 12 scoops for 20oz).
Reinsert the basket into the machine.
3. Remove the lid from the carafe and re-insert
– the lid must not be on the carafe during
the brewing process, alternatively, use
another vessel.
4. Navigate to the COLD BREW setting and
press START|CANCEL. The machine will
then begin brewing the water without the
heating element. Once this is complete
a countdown timer will display on the
LCD indicating when the Cold Brew is
finished. At this point the machine will
automatically dispense the Cold Brew into
the waiting carafe.
NOTE
Brew Time for Cold Brew can easily be
adjusted to your preference, anywhere between
1min – 24hrs.
NOTE
Do not add ice to the tank. Cold, chilled water
should be added.
BDC450_455_USC_IB_I20_FA.indd 17 24/1/20 9:48 am
18
POUR OVER
Provided pour over adapter is to let your Precision Brewer accommodate your favorite
pour over dripper. (Included in BDC455 only. Sold separately at Breville webpage).
Fit 'Pour Over'
showerhead
Caution:
Showerhead
may be hot.
Note:
Please ensure that
POUR OVER
mode is on.
Refit showerhead
ring
Mount adapter
Remove basket
and carafe
Dose with ground
coffee
Adjust parameters, and select
'POUR OVER' then 'ON'
Fill to cup volumePlace dripper on
adapter
Use case as stand
for cup
Rotate SELECT dial to choose
'MY BREW' & press dial
Start brewing
Pour Over mode
is activated
DRIPPER
Unscrew
showerhead ring
Remove
showerhead
13
7
88
5
6
4
99
10 11
14
12
1 2 3
BDC450_455_USC_IB_I20_FA.indd 18 24/1/20 9:48 am
19
DESCALING
After regular use, hard water can cause mineral
build up in internal components, reducing the
brewing flow, brewing temperature, power of the
machine, and taste of the coffee.
We recommend to descale regularly. When LCD
shows “DESCALE” (flashing), descaling cycle
is needed.
NOTE
It takes approximately 15 minutes to complete
descaling cycle.
1. Empty the tank. Prepare a descale solution in
accordance with manufacturer's instructions.
Pour this solution into the empty water tank.
2. Place the basket and the carafe into position
under the drip stop outlet (Ensure the carafe
is empty and the lid is securely locked).
3. Press SELECT button for 3 seconds to start
descaling cycle. LCD with show “dSL” for
1 second and then tell remaining time of
descaling cycle.
4. When the descaling process is finished, the
LCD screen will go back to the main menu.
To completely remove residual water in the
tank, invert the machine and brew with fresh
water twice. Discard the water from the carafe
and rinse thoroughly.
NOTE
We recommend to brew through again
after descaling to brew out the residue
descale solution.
NOTE
You cannot stop the descaling process mid cycle.
Force stop by unplugging the cord from the
power outlet.
FACTORY RESET
This is to reset the machine to the factory settings,
including water hardness setting. Hold the
START button, the SELECT button, and AUTO
START button altogether for 3 seconds. When
LCD shows “rES” (flashing), press SELECT
button to start. Then next prompt asks “YES”
or “no” to confirm. Rotate and press SELECT
dial/button.
Always turn the coffee machine off and remove
the plug from the power outlet before cleaning.
CLEANING THE OUTER HOUSING
The outer housing and LCD screen can be
cleaned with a soft, damp cloth. Apply cleaner
to the cloth and not the LCD surface. Polish
with a soft, dry cloth. Cleaning and drying with
dry paper towels or abrasive cloths and cleaners
may scratch the surface.
CLEANING THE COFFEE BASKET AND
MESH BASKET FILTER
Remove the coffee basket. Discard any ground
coffee and filter paper. The coffee basket and
mesh basket filter can be rinsed under running
water. Ensure the fine holes of the mesh basket
filter are clear. For a deeper clean, wash the
coffee basket and mesh basket filter in warm,
soapy water with a soft bristled brush.
CAUTION
The coffee basket, mesh basket or paper filter
may still be very hot after brewing. Use caution
and allow to cool before removing.
CLEANING THE CARAFE
After each use, empty the carafe. Do not let
brewed coffee stand overnight as this can cause
the carafe to stain. Rinse the carafe and carafe
lid under warm running water. For a deeper
clean, we recommend regularly washing the
carafe in warm, soapy water using a soft bristled
brush. Do not use abrasive cleansers, pads or
cloths which can scratch the surface. Rinse and
dry thoroughly.
CLEANING THE SHOWERHEAD
Simply wipe down the showerhead area
periodically. However, if a more thorough clean
is required, the Showerhead can be removed by
unlocking the Showerhead Ring. Rotate clockwise
then remove the Showerhead for cleaning. Once
complete, reinstall the Showerhead.
Care & Cleaning
BDC450_455_USC_IB_I20_FA.indd 19 24/1/20 9:48 am
20
Troubleshooting
PROBLEM POSSIBLE CAUSE WHAT TO DO
Coffee too strong
or weak
Amount of coffee and water is not
correct (1 spoon : 5oz/150ml cup).
Check correct amount of coffee or
water is used.
Coffee leaking
from basket
when removed
The basket drip-stop seal doesn’t
cover the gap properly due to
foreign material.
Check that there is no obstruction in
the basket drip-stop seal.
Wash out the basket seal by turning
the basket upside down, and pressing
down and rinsing into the seal to clear
any particles obstructing that area.
Coffee overflowing
from the basket
(CAUTION:
If the basket
has overflowed
remove slowly and
with caution)
Carafe is not inserted.
Amount of coffee and water is not
correct (1 spoon : 5oz/150ml cup).
Grind size is too fine.
Too much grinds in the basket.
No paper in the basket.
Putting paper into mesh
basket filter.
If you are brewing with carafe, check
that the carafe is inserted.
Check that the correct amount
of coffee and water is used for
the operation.
Correct grind size/amount.
Use mesh basket filter without paper
and other baskets with paper.
‘FILL TANK’ on
LCD screen
Water tank is empty or not enough
water to brew the selected volume.
Sensors may be dirty.
Open the lid and pour the desired
amount of cold, preferably
filtered water.
While the tank is empty wipe the
sensor prisms in the tank with a cloth.
Auto Start does
not function
Auto Start does not repeat after it
has been activated.
Re-engage the Auto Start mode for
each time that it needs to be used.
Shows ‘CLOCK’
when Auto Start
is pressed
Current time should be set before
setting Auto Start.
Set the current time before using
Auto Start.
Clock does not
remember time
Clock is cleared every time the unit
is unplugged.
Keep the unit plugged.
Auto Start starts
at the wrong time
Current time is not correct.
Check that the current time is correct.
Carafe overfilling
Carafe is not completely empty
before brewing.
Amount of water is too much.
Check that the carafe is empty
before brewing.
Check that the MAX line on the water
tank is not exceeded.
Ensure water runs freely through
carafe lid.
BDC450_455_USC_IB_I20_FA.indd 20 24/1/20 9:48 am
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Breville the Breville Precision Brewer Thermal Manuel utilisateur

Catégorie
Accessoires de préparation de café
Taper
Manuel utilisateur