Bolens 31AE5GLG565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AE5GLG565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

Ce manuel convient également à

31AE5MLH565

Printed in U.S.A.

FORM NO

772C0720

(7/2004)

IMPORTANT: Read safety rules and instructions

P. O. BOX 1386, KITCHENER, ONTARIO N2G 4J1

carefully before operating equipment.

500 series

Snowthrower

Model 6ML Shown

Operator’s Manual

TABLE OF CONTENTS

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new snow thrower. It will help you to assemble, prepare and

maintain the unit for best performance. Please read and understand what it says.

Before you start assembling your new snow thrower, please locate the model plate on the

equipment and copy the information from it in the space provided below. The information on the

model plate is very important if you need help from an authorized dealer.

•You can locate the model number by standing behind the unit in the operating position and looking

down at the dash panel. A sample model plate is explained below. For future reference, please copy the

model number and the serial number of the equipment in the space below.

ENGINE INFORMATION

The engine manufacturer is responsible for all engine-related issues with regards to performance, power-rating,

specifications, warranty and service. Please refer to the engine manufacturer’s Owner’s/Operator’s Manual packed

separately with your unit for more information.

CALLING CUSTOMER SUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or

maintenance of this unit, please call an authorized dealer.

Please have your unit’s model number and serial number ready when you call. See previous section to

locate this information.

Content Page

Customer Support 2

Important Safe Operation Practices 3

Setting Up Your SnowThrower 5

Operating Your Snow Thrower 8

Maintaining Your Snow Thrower 12

Service & Ajustments 13

Off Season Storage 17

Trouble Shooting 18

Warranty 19

Illustrated Parts List 20

Content Page

Copy the model number here:

Copy the serial number here:

MTD PRODUCTS LIMITED

KITCHENER, ON N2G 4J1

1-800-668-1238

XXXXXXXXXX

XXXXXXXXXXX

Model Number

Numéro de modèle

Serial Number

Numéro de série

www.mtdcanada.com

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

WARNING: This symbol points out important safety instructions which, if not followed, could endanger the

personal safety and/or property of yourself and others. Read and follow all instructions in this manual before

attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you

see this symbol—heed its warning.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals

known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with

any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This

machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place

for future and regular reference and for ordering

replacement parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent.

4. Never allow adults to operate this machine without

proper instruction.

5. Thrown objects can cause serious personal injury. Plan

your snow throwing pattern to avoid discharge of material

toward roads, bystanders and the like.

6. Keep bystanders, helpers, pets and children at least 75

feet from the machine while it is in operation. Stop

machine if anyone enters the area.

7. Exercise caution to avoid slipping or falling, especially

when operating in reverse.

Preparation

1. Thoroughly inspect the area where the equipment is to

be used. Remove all door mats, newspapers, sleds,

boards, wires and other foreign objects which could be

tripped over or thrown by the auger/impeller.

2. Always wear safety glasses or eye shields during

operation and while performing an adjustment or repair to

protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

3. Do not operate without wearing adequate winter outer

garments. Do not wear jewelry, long scarves or other

loose clothing which could become entangled in moving

parts. Wear footwear which will improve footing on

slippery surfaces.

4. Use a grounded extension cord and receptacle for all

units with electric start engines.

5. Adjust collector housing height to clear gravel or crushed

rock surfaces.

6. Disengage the control handle before starting the engine.

7. Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

8. Let engine and machine adjust to outdoor temperature

before starting to clear snow.

9. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely

flammable and the vapors are explosive. Serious

personal injury can occur when gasoline is spilled on

yourself or your clothes which can ignite. Wash your skin

and change clothes immediately.

a. Use only an approved gasoline container.

b. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

c. Never fuel machine indoors.

d. Never remove gas cap or add fuel while the

engine is hot or running.

e. Allow engine to cool at least two minutes before

refueling.

f. Never over fill fuel tank. Fill tank to no more than

½ inch below bottom of filler neck to provide space

for fuel expansion.

g. Replace gasoline cap and tighten securely.

h. If gasoline is spilled, wipe it off the engine and

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

i. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

(e.g. furnace, water heater, space heater, clothes

dryer etc.).

j. Allow machine to cool at least 5 minutes before

storing.

Operation

1. Do not put hands or feet near rotating parts, in the auger

housing or discharge chute. Contact with the rotating

parts can amputate hands and feet.

2. The auger control handle is a safety device. Never

bypass its operation. Doing so, makes the machine

unsafe and may cause personal injury.

3. The control handle must operate easily in both directions

and automatically return to the disengaged position when

released.

4. Never operate with a missing or damaged discharge

chute. Keep all safety devices in place and working.

5. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

6. Do not operate machine while under the influence of

alcohol or drugs.

7. Muffler and engine become hot and can cause a burn. Do

not touch.

8. Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while

operating on slopes.

10. Plan your snow throwing pattern to avoid discharge

towards windows, walls, cars etc. To avoid property

damage or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets

or allow anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear

snow at too fast of a rate.

13. Never operate this machine without good visibility or

light. Always be sure of your footing and keep a firm hold

on the handles. Walk, never run.

14. Disengage power to the auger/impeller when

transporting or not in use.

15. Never operate machine at high transport speeds on

slippery surfaces. Look down and behind and use care

when in reverse.

16. If the machine should start to vibrate abnormally, stop the

engine, disconnect the spark plug and ground it against

the engine. Inspect thoroughly for damage. Repair any

damage before starting and operating.

17. Disengage the control handle and stop engine before you

leave the operating position (behind the handles). Wait

until the auger comes to a complete stop before

unclogging the discharge chute, making any

adjustments, or inspections.

18. Never put your hand in the discharge or collector

openings. Always use a clearing tool to unclog the

discharge opening.

19. Use only attachments and accessories approved by the

manufacturer.

20. If situations occur which are not covered in this manual,

use care and good judgment. Call customer assistance

for the name of your nearest servicing dealer.

Maintenance And Storage

1. Never tamper with safety devices. Check their proper

operation regularly.

2. Disengage the control handle and stop engine. Wait until

the auger/impeller come to a complete stop. Disconnect

the spark plug wire and ground against the engine to

prevent unintended starting before cleaning, repairing, or

inspecting.

3. Check bolts, and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

4. Do not change the engine governor setting or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid shoes are subject to

wear and damage. For your safety protection, frequently

check all components and replace with original

equipment manufacturer’s (O.E.M.) parts only. “Use of

parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

6. Check controls periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the

adjustment section in this operator’s manual for

instructions.

7. Maintain or replace safety and instruction labels, as

necessary.

8. Observe proper disposal laws and regulations for gas,

oil, etc. to protect the environment.

9. Prior to storing, run machine a few minutes to clear snow

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light such as a water

heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper

instructions on off-season storage.

Your Responsibility:

• Restrict the use of this power machine to persons who

read, understand and follow the warnings and

instructions in this manual and on the machine.

G R A P H IC S S H E E T

SECTION 2: SETTING UP YOUR SNOW THROWER

NOTE: The snow thrower is shipped with oil and

WITHOUT GASOLINE. After assembly, refer to

separate engine manual for proper fuel and engine oil

recommendations.

NOTE: This Operator’s Manual covers several models,

handle panels, lights and chute cranks are some

features that may vary by model. Not all features

referenced in this manual are applicable to all

snowthrower models.

Unpacking

• Cut along corners of the carton and lay it down flat.

Remove packing material.

• Remove any loose parts included with unit (i.e.,

operator’s manual, etc.).

• Roll unit out of carton. Check carton thoroughly for

any remaining loose part.

Loose Parts

Your snow thrower has been assembled at the factory

except the parts shipped loose in the carton. These are

listed below.

a. Electric Start Cord (optional)

b. Shear Pins and Cotter Pins

Before Assembly

Disconnect spark plug wire and ground it against the

engine to prevent unintended starting.

NOTE: All references in this manual to the left or right

side of the snow thrower is from the operating position

only. Exceptions, if any, will be specified.

Setting up the Snow Thrower

1. Raise the upper handle assembly in the direction

shown in Figure 1. Align the upper handles with the

lower handle.

2. Tighten two handle knobs firmly to secure the

upper handle to the lower handles. See Figure 1.

3. Slide the shift rod connector down over the end of

the lower shift rod. Tap the connector until it locks

over the lower shift rod. See Figure 2.

NOTE: If the connector is not properly assembled, the

shift rod will pivot and changing speed or direction of

the snow thrower will not be possible.

Chute Assembly (all models)

1. Apply a light lubricant (i.e. 3-in-1 oil) to the base of

the chute assembly.

2. Place the chute assembly on the lip of the chute

adapter. See Figure 3.

Figure 1

Figure 2

Figure 3

Handle Knob

Shift Rod

Connector

Chute

Assembly

3. One end of each chute keeper is already attached

to the chute flange. Pivot the free end of the chute

keeper to align it with the chute flange and push it

till it snaps into position. See Figure 4. Repeat with

remaining chute keepers.

Figure 4

For Models with 4 Way Chute Control Box

1. Pull the hairpin clip out of the clevis pin on the chute

support tube. Save this hardware. See Figure 5.

Figure 5

Figure 6

2. Position the chute assembly so the chute opening

is facing the front of the unit.

3. Place the chute control box on the short tube of the

chute assembly and the chute support tube of the

chute assembly as shown in Figure 6, cables

should be towards the operator.

4. Insert the clevis pin, earlier removed, through the

holes on the chute control box and chute support

tube. Secure with the hairpin clip. See Figure 5.

For All Models without Engine Covers

1. Slip the cables, running from the chute to the

handle panel into the cable guide located on top of

the engine. See Figure 7 .

Figure 7

Lamp Wire (optional)

1. Wrap the wire from the lamp down the right handle

as shown in Figure 8 .

2. Plug wire into the alternator lead wire under the fuel

tank. See Figure 8 inset.

Figure 8

Chute Clean-Out Tool

1. The chute clean-out tool is fastened with a cable tie

to the rear of the auger housing for shipping

purposes. Cut the cable tie and remove the

extension cord (optional) before operating the snow

thrower.

Final Adjustments

After setting up your snow thrower, check the

adjustments as instructed below and make any final

adjustments necessary before operating the unit.

CAUTION: Perform the following test before operating

the snow thrower for the first time and at the start of

each winter season. Failure to comply with these

adjustment instructions may cause damage to the unit.

Chute

Assembly

Chute Keeper

Chute Support

Tube

Clevis

4 Way

Chute

Control

Box

Hairpin Clip

Chute Support

Tube

Short

Tube

Cables

Cable Guide

Alternator Lead

Lamp Wire

Alternator

Lead

NOTE: Wheels are omitted from illustration for clarity.

Auger Control Test

1. To check the adjustment of the auger control, push

forward the left hand control until the rubber

bumper is compressed. There should be slack in

the cable.

2. Release the control. The cable should be straight.

Make certain you can depress the auger control

grip against the left handle completely.

• If adjustment is necessary, loosen the hex jam nut

and rotate the coupling end of the cable (without

turning the cable) counterclockwise to provide

more slack.

3. Recheck the adjustment. Tighten jam nut against

the cable when correct adjustment is reached.

Figure 9

Drive Control & Shift Lever

1. Tip the snow thrower forward so that it rests on the

auger housing.

2. Move the shift lever all the way forward to the sixth

(6) position.

3. With the drive control lever released, spin the snow

thrower wheels by hand. The wheels should turn;

however, you may feel some resistance.

4. Engage the drive control. The wheels should no

longer turn.

5. Now release the drive control and spin the wheels

again.

6. Move the shift lever back to the fast reverse

position and then all the way forward again. There

should be no resistance in the shift lever and the

wheels should turn.

7. If you face resistance when moving the shift lever

or the wheels stop when they should not, loosen

the lock nut on the traction drive cable and

unthread the cable one turn.

8. If the wheels can still be turned when you engage

the drive control, loosen the hex jam nut and rotate

the coupling end of the cable (without turning the

cable) in one turn. Recheck the adjustment and

repeat if needed.

9. Tighten the jam nut to secure the cable when

correct adjustment is reached.

NOTE: For further details, refer to the Adjustment

section on page 16.

Skid Shoe

Locate the shave plate and the skid shoes in Figure

12. The space between this shave plate and the

ground can be adjusted. For close snow removal,

place skid shoes in the low position. Use middle or

high position when area to be cleared is uneven.

It is not recommended that you operate this snow

thrower on gravel as loose gravel can be easily picked

up and thrown by the auger causing personal injury or

damage to the snow thrower.

If for some reason, you have to operate the snow

thrower on gravel, keep the skid shoe in the highest

position for maximum clearance between the ground

and the shave plate.

Some models are equipped with reversible skid shoes

and may be turned over to increase their lifespan. See

Figure 11.

Figure 10- Standard Skid Shoe

Figure 11- Reversible Skid Shoe

WARNING: Do not over-tighten the cable.

Over-tightening may prevent the auger from

disengaging and compromise the safety of the

snow thrower.

Jam

Nut

Auger

Cable

Coupling

Hex Jam Nut

Skid

IMiddle

High

Low

Shoe

1. Adjust skid shoes by loosening the four hex nuts

(two on each side) and carriage bolts. Move skid

shoes to desired position.

2. Make certain the entire bottom surface of skid shoe

is against the ground to avoid uneven wear on the

skid shoes. Retighten nuts and bolts securely.

3. Retighten the hex jam nut and repeat all three tests

to verify proper adjustment has been achieved.

Tire Pressure (Pneumatic Tires)

The tires are over-inflated for shipping purposes.

Check tire pressure and reduce to 15-20 psi.

NOTE: If the tire pressure is not equal in both tires, the

unit may pull to one side or the other.

SECTION 3: OPERATING YOUR SNOW THROWER

Know The Controls

Read this owner’s manual and safety rules before operating your snow thrower. Compare Figure 12 with your snow

thrower to familiarize yourself with the location of various controls and adjustments. Maintain safety while learning

about the controls and operating the unit. Save this manual for future reference.

Figure 12

Drive Control/ Auger Control Lock

The drive control is located on the right handle.

Squeeze down the traction control to engage the wheel

drive. Release to stop.

The drive control also locks the auger control so you

can operate the chute crank without interrupting the

snow throwing process. If the auger control is engaged

simultaneously with the drive control, the operator can

release the auger control (on the left handle) and the

augers will remain engaged. Release the traction

control to stop the augers and wheel drive (the auger

control must also be released).

Drive Control

Shift Lever

Chute Control

Auger Control

Wheel Steering

Control

Auger

Chute Clean-Out Tool

Chute Assembly

Gas Tank

Skid Shoe

Shave Plate

Headlight

IMPORTANT:

Always release the drive control before

changing speeds.

Auger Control

The auger control is located on the left

handle. Squeeze the auger control to

engage the augers. Release to stop the

snow throwing action. The drive control

must also be released in order to stop

the auger.

IMPORTANT:

Refer to Auger Control Test on page 7 to

adjust the auger control. Read and follow all

instructions carefully and perform all adjustments to

verify your snow thrower is operating safely and

properly.

Ignition Key

The ignition key must be fully inserted in the switch

before the unit will start. Remove key when snow

thrower is not in use. Do not attempt to turn the key.

Discharge Chute

The angle of the discharge chute controls the distance

that the snow is thrown. Tilt the discharge chute up for

greater distance; tilt down for less distance.

Four Way Chute Control

This four-way control lever is meant to

control the direction and distance of

snow discharge from the chute. Press

the button on the knob and pivot it left

or right to rotate the chute to the

direction that snow will be thrown. Tilt

the lever forward or rearward to adjust

the distance snow will be thrown.

Shift Lever

The shift lever is located in the center

of the handle panel and is used to

determine ground speed and direction

of travel. It can be moved into any of

eight positions.

IMPORTANT:

Always release traction control before

changing speeds.

Forward: The snow thrower has six forward (F)

speeds. Position one (1) is the slowest and position six

(6) is the fastest.

Reverse: The snow thrower has two reverse (R)

speeds—R1 is the slower of the two.

Headlight

The headlight is on whenever the engine is running.

Chute Clean-Out Tool

The chute clean-out tool is designed to clear a clogged

discharge chute. Refer to page 12 for instructions on

how to properly use it.

Wheel Steering Controls

The left and right wheel steering

controls are located on the underside

of the handles. Squeeze the right

control to turn right; squeeze the left control to turn left.

NOTE: Operate the snow thrower in open areas until

you are familiar with these controls.

Skid Shoe

The skid shoe position is determined by the condition of

the ground from where snow has to be removed. Higher

the snow level, lower will be the skid shoe level. Adjust

it accordingly.

Stopping Snow Thrower

1. To stop the wheels, release the traction drive lever

of the snow thrower.

2. To stop throwing snow, release the auger drive lever.

3. To stop the engine, push throttle control lever to

OFF and pull out the ignition key. Do not turn key.

Before Starting

WARNING: Read, understand, and follow

all instructions and warnings on the machine

and in this manual before operating.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in

the separate engine manual packed with your snow

thrower. Read instructions carefully.

WARNING: Use extreme care when

handling gasoline. Gasoline is extremely

flammable and the vapors are explosive.

Never fuel the machine indoors or while the

engine is hot or running. Extinguish cigarettes,

cigars, pipes and other sources of ignition.

Starting The Engine

• Attach spark plug wire to spark plug. Make certain

the metal loop on the end of the spark plug wire

WARNING: Never use your hand to clear a

clogged discharge chute. Shut off engine and

remain behind handles until all moving parts

have stopped before unclogging.

WARNING: Be sure no one other than the

operator is standing near the snow thrower

while starting or operating. Do not operate this

snow thrower unless the discharge chute

assembly has been properly installed and is

secured.

(inside the boot) is fastened securely over the metal

tip on the spark plug.

• Make certain both the auger control and drive

control are in the disengaged (released) position.

• Move throttle control up to FAST position. Insert

ignition key into slot. Make sure it snaps into place.

Do not attempt to turn the key

NOTE:

The engine cannot start unless the key is

inserted into ignition switch.

Electric Starter

Before starting, make sure that the engine has suffi-

cient oil. The snow thrower engine is equipped with a

120 volt A.C. electric starter and recoil starter. The

electric starter is equipped with a three-wire power

cord and plug and is designed to operate on 120 volt

AC household current. Follow all instructions carefully.

Cold Start

NOTE: If the unit shows any sign of motion (drive or

augers) with the clutch grips disengaged, shut the

engine off immediately. Readjust as instructed in the

“Final Adjustments” section of the Assembly

Instructions.

1. Determine whether your house wiring is a three-

wire grounded system. Ask a licensed electrician if

you are not certain.

• If your house wiring system is grounded and a

three-hole receptacle is not available at the point

the snow thrower starter will normally be used, one

should be installed by a licensed electrician.

• When connecting the power cord, always connect

cord to starter on engine first, then plug the other

end into a three-hole grounded receptacle.

• When disconnecting the power cord, always

unplug the end from the three-hole, grounded

receptacle first.

2. Attach spark plug wire to spark plug.

3. Make sure that the auger drive and the traction

drive levers are in the disengaged position.

4. Move throttle control lever to FAST position.

5. Push key into the ignition slot. Make sure it snaps

into place. Do not turn key.

6. Rotate the choke knob to FULL choke position.

7. Push the primer three times.

8. Connect power cord to switch box on the engine.

9. Plug the other end of the power cord into a three-

hole, grounded 120 volt A.C. receptacle.

10. Push down on the starter button until the engine

starts. Do not crank for more than 10 seconds at a

time. This electric starter is thermally protected. If

overheated, it will stop automatically and can be

restarted only when it has cooled to a safe

temperature (a wait of 5 -10 minutes is required).

11. When the engine starts, release the starter button

and slowly rotate the choke to OFF position. If the

engine falters, rotate the choke to FULL and then

gradually to OFF.

12. Disconnect the power cord from the receptacle first

and then from the switch box on the engine.

13. Allow the engine to warm up for a few minutes

because the engine will not develop full power until

it reaches operating temperature. Operate the

engine at full throttle (FAST) when throwing snow.

Warm Start

1. If restarting a warm engine, rotate choke to OFF

instead of FULL and press the starter button.

Recoil Starter

Make sure that the engine has sufficient oil and the

auger drive and the traction drive levers are released.

Cold Start

1. Move throttle control to FAST position.

2. Push key into the ignition slot so that it snaps into

place. Do not turn key.

3. Rotate choke control to FULL choke position.

4. Push the primer button while covering the vent hole.

Remove your finger from the primer between primes.

Do not prime if temperature is above 50

F (10

C);

prime two times between 50

F (10

C) and 15

(-9

C); and prime four times below 15

F (-9

C).

5. Pull the starter handle rapidly. Do not allow the

handle to snap back, but allow it to rewind slowly

while keeping a firm hold on the starter handle.

6. As the engine warms up and begins to operate

evenly, rotate the choke knob slowly to OFF

position. If the engine falters, return to FULL choke,

then slowly move to OFF choke position.

7. Allow the engine to warm up for a few minutes

because the engine will not develop full power until

it reaches operating temperature.

8. Operate the engine at full throttle (FAST) when

throwing snow.

Warm Start

1. If restarting a warm engine after a temporary shut

down, rotate choke to OFF instead of FULL and do

not prime. Pull starter handle as instructed earlier.

Frozen Recoil Starter

If the starter is frozen and will not turn the engine,

proceed as follows:

1. Pull as much rope out of the starter as possible.

2. Release the starter handle and let it snap back

WARNING: The electric starter must be

properly grounded at all times to avoid the

possibility of electric shock which may be

injurious to the operator.

WARNING: If your house wiring system is not

a three-wire grounded system, do not use this

electric starter under any conditions.

against the starter.

3. If the engine still fails to start, repeat the first two

steps. If continued attempts do not free starter,

follow the electric starter procedures to start.

4. Avoid freezing of the recoil starter by referring to

instructions below.

Before Stopping

1. Run engine for a few minutes to help dry off any

moisture on engine.

2. Avoid freezing of the starter by following these

steps before stopping the snow thrower:

Recoil Starter

a. With the engine running, pull the starter rope

with a rapid, continuous full arm stroke three

or four times.

Electric Starter

a. Connect power cord to switch box, then to

120 Volt AC receptacle.

b. While the engine is running, push the starter

button and spin the starter for several

seconds.

c. Disconnect power cord from the receptacle

first, then from the snow thrower.

NOTE: The unusual sound from pulling the starter rope

in case of the recoil starter, or from spinning the starter

in case of the electric starter, will not harm the engine.

To Stop The Snow Thrower

1. To stop the wheels, release the traction drive lever

on the snow thrower.

2. To stop throwing snow, release auger drive lever.

3. To stop engine, push throttle control lever to OFF

and pull out the key. Do not turn key.

To Engage Drive

1. With the engine running near top speed, move shift

lever to one of six FORWARD positions or two

REVERSE positions. Select a speed appropriate

for the snow conditions that exist. Use slower

speeds until you are familiar with the process.

2. Squeeze traction drive clutch grip against the right

handle and the snow thrower will move. Release it

and the drive motion will stop.

To Engage Augers

1. To engage augers and start snow throwing,

squeeze the left hand auger clutch grip against the

left handle. Release to stop augers.

2. While the auger control is engaged, squeeze the

drive control to move, release to stop. Do not shift

speeds while the drive is engaged.

NOTE: This same lever also locks auger control so you

can turn the chute crank without interrupting the snow

throwing process.

3. Release the auger control; the interlock mechanism

should keep the auger control engaged until the

traction drive control is released.

4. Release the drive control to stop both the augers

and the wheel drive. To stop the auger, both levers

must be released.

To Throw Snow

CAUTION: Check the area to be cleared for foreign

objects. Remove, if any.

1. Start the engine following starting instructions.

2. Rotate the discharge chute to the desired position,

(away from bystanders and/or buildings) by moving

the chute control.

3. Select the speed according to snow condition.

CAUTION: Never move the shift lever without first

releasing the drive clutch.

4. Engage the auger control and drive control levers

following instructions above.

5. The interlock feature will allow you to remove your

left hand from the auger control lever.

6. When clearing the first pass through the snow,

control speed of snow thrower according to the

depth and condition of snow.

7. To turn the unit left or right, squeeze the respective

wheel steering control. See Figure 12.

8. On each succeeding pass, readjust the chute to the

desired position and slightly overlap previous path.

9. After the area is cleared, stop the snow thrower

following instructions given below.

Operating Tips

NOTE: Allow the engine to warm up for a few minutes

as the engine will not develop full power until it reaches

operating temperature.

• For most efficient snow removal, remove snow

immediately after it falls.

• Discharge snow downwind whenever possible.

Slightly overlap each previous swath.

• Set the skid shoes 1/4" below the scraper bar for

normal usage. The skid shoes may be adjusted

upward for hard-packed snow.

NOTE: It is not recommended that you operate this

snow thrower on gravel as loose gravel can be easily

picked up and thrown by the auger causing an injury or

damage to the snow thrower.

WARNING: The temperature of muffler and

surrounding areas may exceed (150

F (65

C). Avoid these areas.

• If for some reason, you have to operate the snow

thrower on gravel, keep the skid shoe in the highest

position for maximum clearance between ground

and shave plate.

• Clean the snow thrower thoroughly after each use.

Chute Clean-Out Tool

The chute clean-out tool is conveniently fastened to the

rear of the auger housing with a mounting clip. Never

use your hand to clean a clogged chute.

1. Release both the auger control lever and the

traction/auger control lock lever.

2. Stop the engine by removing the ignition key.

3. Remove the clean-out tool from the clip which

secures it to the rear of the auger housing. See

Figure 13 .

4. Use the shovel-shaped end of the clean-out tool to

remove any snow and ice in the discharge chute.

5. Re-fasten the clean-out tool to the mounting clip on

the rear of the auger housing and restart engine.

6. While standing in the operator’s position (behind

the snow thrower), engage the auger clutch lever

for a few seconds to clear any remaining snow or

ice from the discharge chute before continuing to

clear snow.

Figure 13

SECTION 4: MAINTAINING YOUR SNOW THROWER

General Recommendations

• Always observe safety rules when performing any

maintenance.

• The warranty on this snow thrower does not cover

items that have been subjected to operator abuse

or negligence. To receive full value from the

warranty, operator must maintain the snow thrower

as instructed in this manual.

• Some adjustments will have to be made

periodically to maintain your unit properly.

• Periodically check all fasteners and make sure

these are tight.

Engine

Refer to the separate engine manual packed with your

unit for all engine maintenance.

Lubrication

• Engine: Refer to the separate engine manual

packed with your unit.

• Drive Mechanism: Once a season or after every

25 hours of operation, remove rear frame cover and

lubricate any chains, sprockets, gears, bearings,

and shafts with engine oil or lubricant spray.

IMPORTANT:

Avoid oil spillage on rubber friction wheel

and aluminum drive plate.

• Hex Shaft: Once a season, lubricate the hex shaft

with a penetrating oil, but not grease,

• Gear Case: The gear case is lubricated with

grease at the factory and does not require regular

lubrication. However, if disassembled for any

reason, lubricate with 2 ounces of Shell Alvania™

grease (part # 737-0168). Before reassembling,

remove old sealant and apply new sealant.

IMPORTANT:

Do not overfill the gear case, since

damage to the seals could result. Be sure the vent plug

is free of grease in order to relieve pressure.

• Wheels: Once a season, remove the bolt from

each wheel and take the wheel off the axle. Apply a

multipurpose automotive grease on the shaft

before putting back the wheels.

• Shift Rod: Use a grease or light oil to lubricate the

rotating parts of the shift rod after 25 hours of

operation.

• Pivot Points: All pivoting points on the

snowthrower should be lubricated with a light oil

once a season. If the unit is equipped with grease

fittings, use a grease gun to lubricate these.

• Drive/Auger Control Lock: The cam on the ends

of the control rods which interlock the traction drive

and auger drive clutches must be lubricated at least

once a season or every 25 hours of operation using

a multi-purpose automotive grease. The cam can

be accessed beneath the handle panel

Mounting Clip

Clean-Out

Tool

Auger

Housing

WARNING: Always stop engine and

disconnect spark plug wire before

performing any maintenance or adjustments.

Figure 14

Check V-Belts

Follow instructions below to check the condition of the

drive belts every 50 hours of operation.

1. Remove the plastic belt cover on the front of the

engine by removing two self-tapping screws.

2. Visually inspect for frayed, cracked, or excessively

worn out belts. Replace, if necessary, following

instructions on page 14.

Check Friction Wheel

Follow instructions below to check the condition of the

friction wheel rubber every 50 hours of operation.

1. Remove two self-tapping screws from the frame

cover underneath the snow thrower. Refer to

Figure 18.

2. Visually inspect the friction wheel rubber for

excessive wear, cracks, or loose fit on the friction

wheel drive hub.

3. Also engage the drive control and check if the

friction wheel is making contact with drive plate. If it

does not make contact, adjust the drive cable and

recheck the friction wheel.

4. Replace friction wheel rubber if necessary. Refer to

instructions on page 15.

5. Re-attach frame cover to the snow thrower and put

the equipment back to operating position.

Check Chute Cables

Once a season or every 25 hours of operation,

whichever is earlier, check whether the chute cables

have slackened. Adjust if necessary, following

instructions on page 17.

SECTION 5: SERVICE & ADJUSTMENT

• All adjustments in the Service and Adjustments

section of this manual should be checked at least

once each season.

Servicing Augers

The augers are secured to the spiral shaft with two

shear pins and cotter pins. See Figure 15 . If you hit a

foreign object or ice jam, the snow thrower is designed

so that the bolts will shear.

1. If the augers do not turn, check to see if the pins

have sheared.

2. Replace the pins if needed. Two replacement shear

pins and cotter pins have been provided with the

snow thrower. Spray an oil lubricant into shaft

before inserting new pins and securing with new

cotter pins. See Figure 15.

Figure 15

Lubricate pivot points

Lubricate cams

Lubricate gear case

Lubricate axle

Lubricate

shift rod &

shift arm

WARNING: Always stop the engine,

disconnect spark plug wire and move it away

from the spark plug before performing any

adjustments or repairs.

Cotter Pin

Shear Pin

Auger

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the

snow thrower are subject to wear. Check these

periodically and replace as necessary.

Replacing Skid Shoe

1. Remove four carriage bolts and hex nuts which

attach two skid shoes to the snow thrower on two

sides. See Figure 16 .

2. Reassemble new skid shoes with the same

hardware. Make certain the skid shoes are

adjusted to be level.

Replacing Shave Plate

1. After removing both skid shoes, remove four

carriage bolts and hex nuts which attach shave

plate to the snow thrower housing. See Figure 16 .

2. Reassemble new shave plate, making sure heads

of the carriage bolts are to the inside of the housing.

Tighten securely. Re-install skid shoes.

Figure 16

Replacing Belt

Check the condition of both auger belt and drive belt

every 25 hours of snow thrower operation. Replace if

either shows signs of wear and tear.

1. Remove belt cover by removing the two self-

tapping screws that secure it to the snow thrower

frame. See Figure 17A.

2. Take auger belt off the pulley as shown in Figure

17B.

Auger Belt

3. Tip the snow thrower up and forward, so that it rests

on the housing. Remove two self-tapping screws

from the frame cover underneath the snow thrower

and move the frame cover away. See Figure 18 .

4. Half turn shoulder screw and slide it out of the

mounting bracket. See Figure 19.

5. Unhook spring to release tension on the auger belt.

Remove old belt and replace with new belt

installing it on the groove. See Figure 19.

Figure 17

Figure 18

6. Wrap auger belt around the auger pulley. See

Figure 19.

Figure 19

7. Re-insert shoulder screw into the mounting bracket

and tighten to secure.

8. Wrap auger belt behind the idler. Reattach the

spring to the bolt where it was earlier secured.

Skid Shoe

Nut

Shave Plate

Hex Nut

Carriage Bolt

Belt Cover

Self-Tapping

Screw

Self-Tapping

Screw

Pulley

Auger Belt

Engine

Frame Cover

Shoulder

Screw

Spring

Auger

Pulley

Mounting Bracket

9. Re-install frame cover and flip the snow thrower

back to the operating position.

10. Wrap auger belt around the engine pulley.

11. Re-install belt cover with self-tapping screws

removed before.

Drive Belt

Push idler counter-clockwise and insert a Philips

head screwdriver in the hole on the idler as shown

in Figure 20. This will release tension on drive belt.

Figure 20

4. Pull drive belt out and away from the engine pulley

to remove. See Figure 20.

5. Tip the snow thrower up and forward, so that it rests

on the housing. Remove two self-tapping screws

from frame cover underneath the snow thrower and

move the frame cover away. Refer to Figure 18.

6. Back out the stop bolt to create sufficient gap

between the friction wheel disc and the drive pulley.

Pull the drive belt from around the drive pulley and

clear it off the friction wheel disc. See Figure 21.

Figure 21

7. Now moving to the other side of the snow thrower

again, slide the belt off the crankshaft.

8. Replace with new belt, first sliding it through the

crank shaft, then working it around the groove of

the drive pulley and finally wrapping it around the

engine pulley from where the old belt was removed.

Once the belt is firmly placed on the pulleys, make

sure to remove the screwdriver from the idler.

9. Re-install auger belt on the engine pulley.

10. Re-attach frame cover on the snow thrower frame

and put the equipment back to operating position.

Re-attach belt cover with two self-tapping screws

removed earlier.

Friction Wheel Rubber

1. Check the rubber on the friction wheel after 25

hours of operation, and periodically thereafter.

Replace the rubber if any signs of wear or cracking

are found.

2. Drain the gasoline from the snow thrower, or place

a piece of plastic under the gas cap. Move shift

lever to the R2 position.

3. Tip the snow thrower so that it rests on the housing.

Remove two self-tapping screws from the frame

cover underneath the snow thrower.

4. Remove bolt securing the right wheel, and remove

the wheel from the axle.

5. Remove the four screws securing the right drive

cover to the frame. Remove the drive cover from

the side of the frame. See Figure 22.

6. Holding the friction wheel assembly, slide the hex

shaft to the right. See Figure 23. The spacer on

right side of hex shaft may fall.

7. Lift the friction wheel assembly out between the

axle shaft and the drive shaft assemblies.

8. Remove the four screws from the friction wheel

assembly. Remove friction wheel rubber from

between the friction wheel plate. See Figure 24.

Figure 22

First two steps are on page 14.

Engine

Pulley

Idler

Drive Belt

Auger Belt

Stop

Bolt

Drive Pulley

Friction

Wheel

Drive

Belt

Drive Cover

Bolt

Spacer

Figure 23

Figure 24

9. Reassemble new friction wheel rubber to the

friction wheel assembly, tightening the four screws

in rotation and with equal force. See Figure 24.

IMPORTANT:

Assemble the rubber on the friction wheel

equally for proper functioning.

10. Insert the shift arm assembly into the friction wheel

assembly and hold assembly in position. See

Figure 25.

11. Slide hex shaft through right side of the housing

and the friction wheel assembly.

12. Insert the hex shaft through the sprocket and the

spacer. Make certain that chain engages both the

large and the small sprocket.

NOTE: If the sprocket fell from the snow thrower while

removing the hex shaft, place the sprocket on the hex

shaft. Position the hex hub of the sprocket toward the

friction wheel when sliding the sprocket on to hex shaft.

13. Align the hex shaft with the left bearing and

carefully guide this bearing into left side of housing.

14. Install the right bearing on the hex shaft and check

that the spacer and bearing in the drive cover are

aligned to the steerable shaft. See Figure 25 .

15. Reassemble the drive cover with four screws

removed in step 6. Install the right wheel with the

bolt removed earlier.

16. Reassemble the frame cover with the two self-

tapping screws. Flip the equipment back to the

operating position and re-attach the belt cover.

Figure 25

NOTE: If you placed plastic under the gas cap, be

certain to remove it.

Adjustments

Drive Clutch

Refer to the Final Adjustment section of the Assembly

instructions to adjust the drive clutch. To check the

adjustment, proceed as follows:

• Drain the gasoline out of your snow thrower’s

engine, and place a piece of plastic film under the

gas cap to avoid spillage.

• Tip the snow thrower forward, allowing it to rest on

the auger housing.

• Remove the frame cover underneath the snow

thrower by removing self-tapping screws.

• With the traction control released, check if there is

1/8” clearance between friction wheel and drive

plate in all positions of the shift lever.

• With the traction control lever engaged, check if the

friction wheel solidly contacts the drive plate. See

Figure 21. If not, adjust as follows:

• Loosen the jam nut on the traction drive cable and

thread the cable in or out as necessary.

• Retighten the jam nut to secure the cable when

correct adjustment is reached.

17. Reassemble the frame cover.

NOTE: If you placed plastic under the gas cap, be

certain to remove it.

Auger Clutch

Refer to instructions on page 6 to adjust the auger

control.

Shift Rod

To adjust the shift rod, proceed as follows.

1. Place shift lever in the fastest forward speed. See

Figure 26A.

2. Remove hairpin clip from the shift handle under the

handle panel. See Figure 26B.

3. Push shift arm assembly down as far as it will go.

Sprocket

Bearing

Screw

Friction

Wheel

Rubber

Plate

Friction

Hex Shaft

Shift

Arm

Wheel

See Figure 26C.

4. Thread the ferrule up or down the shift rod as

necessary until the ferrule lines up with the upper

hole in the shift lever. See Figure 26B.

5. Insert ferrule into the upper hole in shift lever as

shown in Figure 26B.

6. Reinstall the hairpin clip.

7. Check for correct adjustment before operating the

snow thrower.

Figure 26

Skid Shoe

Refer to page 7 for details.

Chute Control

If the chute does not rotate fully or its pitch cannot be

moved up or down, the four chute control cables will

have to be adjusted. Once a season or every 25 hours

of operation, whichever is earlier, check whether the

cables have slackened.

To adjust these cables, proceed as follows:

1. To tighten cable, loosen the top nut and tighten the

bottom nut on the cable.

2. Adjust equally on both sides by working on both

cables of each pair. See Figure 27.

Figure 27

SECTION 6: OFF-SEASON STORAGE

If unit is to be stored over 30 days, prepare for storage

as instructed in the separate engine manual packed

with your unit.

• Clean snow thrower thoroughly.

• Lubricate as instructed in the Maintaining Your

Snow Thrower section of this manual.

• Store the snow thrower in a clean, dry area.

• Refer to the engine manual for correct engine

storage instructions.

NOTE: When storing any type of power equipment in a

poorly ventilated or metal storage shed, care should be

taken to rustproof the equipment, especially springs,

cables and all moving parts.

Shift

Lever

Shift Arm

Shift

Rod

Ferrule

Hairpin Clip

Chute

Control

Chute Control Cable

WARNING: Never store snow thrower with

fuel in tank indoors or in poorly ventilated

areas, where fuel fumes may reach an open

flame, spark or pilot light as on a furnace, water

heater, clothes dryer or gas appliance.

SECTION 7: TROUBLESHOOTING

NOTE: This section addresses minor service issues. For further details, contact an authorized service

center for assistance.

Problem Cause Remedy

Engine fails to start.

1. Fuel tank empty, or stale fuel.

2. Blocked fuel line.

3. Choke not in ON position

4. Faulty spark plug.

5. Safety key not in ignition switch on engine.

6. Spark plug wire disconnected.

7. Primer button not being used properly.

1. Fill tank with fresh gasoline.

2. Clean the fuel line.

3. Move switch to ON position

4. Clean, adjust gap or replace.

5. Insert the key fully into the switch.

6. Connect spark plug wire.

7. Contact service center.

Engine runs erratic.

1. Unit running on CHOKE.

2. Blocked fuel line or stale fuel.

3. Water or dirt in fuel system.

4. Carburetor out of adjustment.

1. Move choke lever to OFF position.

2. Clean fuel line and fill tank with clean,

fresh gasoline.

3. Drain fuel tank and carburetor. Refill

with fresh fuel.

4. Contact service center.

Loss of power.

1. Spark plug wire loose.

2. Gas cap vent hole plugged.

3. Exhaust port plugged.

1. Connect and tighten spark plug wire.

2. Remove ice and snow from gas cap. Be

certain vent hole is clear.

3. Contact service center.

Engine overheats.

1. Carburetor not adjusted properly. 1. Contact service center.

Excessive vibration.

1. Loose parts or damaged auger. 1. Stop engine immediately and

disconnect spark plug wire. Tighten all

bolts and nuts. If vibration continues,

have unit serviced by an authorized

service center.

Unit fails

to propel itself.

1. Traction control cable in need of

adjustment.

2. Drive belt loose or damaged.

1. Adjust traction control cable. Refer to

Adjustments.

2. Replace drive belt.

Unit fails

to discharge snow.

1. Discharge chute clogged.

2. Foreign object lodged in auger.

3. Auger control cable in need of adjustment.

4. Auger belt loose or damaged.

5. Shear bolt(s) sheared.

1. Stop engine immediately and

disconnect spark plug wire. Clean

discharge chute and inside of auger

housing.

2. Stop engine immediately and

disconnect spark plug wire. Remove

object from auger.

3. Refer to Final Adjustments on page 6.

4. Refer to page 14.

5. Replace with new shear bolt(s).

SECTION 8: TWO YEAR LIMITED WARRANTY

For TWO YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option,

repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or

workmanship.

This warranty does not cover:

1.Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident,

improper maintenance or alteration; or

2.The unit if it has not been operated and/or maintained in accordance with the owner’s instructions

furnished with the unit; or

3.The engine or motor or component parts thereof which carry separate warranties from their

manufacturers. Please refer to The applicable manufacturer’s warranty on these items; or

4.Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or

component parts thereof are covered by a one year warranty; or

5.Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or

adjustments such as brake, clutch or deck; or

6.Normal deterioration of the exterior finish due to use or exposure.

Full Ninety Day Warranty on Battery: For ninety (90) days from the date of retail purchase, if any battery included

with this unit proves defective in material or workmanship and our testing determines the battery will not hold a

charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery: After ninety (90) days but within one hundred twenty (120)

days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the original

purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.

Full Sixty Day Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adapters, blades,

grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the

original purchaser to be free from defects in material and workmanship for a period of sixty (60) days from the date

of retail purchase.

How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service

dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238.

The return of a complete unit will not be accepted by the factory unless prior written permission has been extended

by MTD PRODUCTS LIMITED.

Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment

are the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this

warranty must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.

Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is

limited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty

provide the sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its

products.

MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss.

41A

41B

41C

42A

42B

42D

42E

42F

42G

42C

42H

42I

42J

42K

43A

43B

43C

43D

43E

43F

La page est en cours de chargement...

Bolens 31AE5GLG565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AE5GLG565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

Ce manuel convient également à

31AE5MLH565

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 31AE5GLG565 Owner's manual

Bolens 31AE5GLG565 Le manuel du propriétaire

Ce manuel convient également à

Bolens 31AE5GLG565 Le manuel du propriétaire

dans d''autres langues

Autres documents