Art Decor I-04-0042-BW/A Mode d'emploi

Taper
Mode d'emploi
KONTUR EVO
INSTALLATION INSTRUCTIONS
STEP 1 - Installing Supports
OUTSIDE POST
CARRIERS
COVER PLATE
INSIDE POST
BACK PLATE
STEP 2 - Splice track if necessary
CENTER
SUPPORT
SET SCREWS
SPLICE
STEP 4 - Installing Outside Posts
STEP 3 - Attach Quadra if necessary
STEP 4 - Attach Return if necessary
1. Join the track sections
together.
2. Tighten set screws.
3. Screw Center Support
directly into center hole
of Splice.
4. Cover splice with
Splice Cap after
installation is complete.
OUTSIDE POST
FINIAL
VALANCE JOINER
M-6 BOLT COVER PLATE INSIDE POST
1. Install Back Plate to wall. Make sure all M-6 bolts are level.
If you have a spliced track the Center Support must be
installed at the position of splice.
2. Cover Back Plate with Cover Plate.
3. Screw on Inside Post very securely. Do not leave any play.
1. Install Valance Joiner to Quadra. Flip Joiner when installing
from left side and right side fi nials.
2. Slide Support brick into Joiner channel. Install screw but leave
slack. Slip screw over Valance joiner and tighten.
1. Insert Support Brick into the Return’s Joiner Track.
2. Attach Ballast with screw onto Return, do not completely tighten.
3. Insert Support Brick into Rail Joiner Track.
Install screw into Support Brick but leave slack.
4. Slip slack screw into Ballast and line up Return and Rail so
Return reaches back edge of Rail. Tighten both screws.
5. Place Corner Cover over Return and Rail Corner. Tighten top
screws till Corner Cover is secure.
1. Loosen all screws on Outside Posts.
2. Slide Ouside Posts into back channel of Rail.
3. Align Outside Posts with Inside Posts from Step 1.
Height calculation for regular clips.
Add 1 1/8” to length of drapes, plus at least 1/2” clearence
from the fl oor. This measurement is the distance from fl oor to
center point of Back Plate.
Please note drapes should not touch rail,
install pin on hooks with this in consideration.
BALLAST
CORNER COVER
1
2 3
4
5
STEP 4 - Mount rail onto supports
Step 5 - Hand draw system
1. Install Endcaps and then click in carriers.
2. Attach baton to side of drape you wish to operate from by clipping
it into the fi rst carrier.
3. Use plastic plug to lock last carries into place so end of drape
dose not move then the drape is fully closed.
1. Slide Outside Posts over
Inside Posts.
2. Once all Outside Posts
including Center Supports
are in place, tighten
posts securely by turning
clockwise.
3. Tighten set screws.
4. Finished result for
Center Supports.
5. Finished result for
side posts.
Step 6 - Cord draw system
1. Install Endcaps and then click in carriers.
2. For center opening tracks greater than 84”, click in plastic plug
at center point of rail.
PLUG
STEP 6 - Cord Draw Systems, Installing Pulley
1. Attach pulley to cord. Stretch pulley until cord is tight. It is
not necessary to use excessive tension. Mark spot with pencil
on wall or fl oor. Remove cords and install pulley then
re-install cords.
THE PULLEY MUST BE INSTALLED. IT IS THE LAW.
FAILURE TO DO SO CAN RESULT IN
INJURY TO CHILDREN OR PETS!
2. IF NEEDED - To adjust CONTROL cord drop, pull cord through
master carrier until pulley is at desired height. Pull cord an extra
few inches and knot cord at proper spot.
When you install the pulley the cord will slide back into place.
INSTALLATION D’UNE MISE À JOUR EURO-SCOPE
KONTUR, NEXGEN, TEKNO 25, TEKNO 40
ÉTAPE 3 - L’installation du rail
BOUCHON
ÉTAPE 1 - Assemblage du rail lorsque le splice est inclus
1. Installez les embouts et insérez suite les glissière dans le rail.
2. Attachez le lance-rideau à la première glissière sur le côté desiré
(ouverture à gauche ou à droite manuelle).
ÉTAPE 4 - Installation du la poulie
1. Déterminez si la corde sera du même côté que le lance-rideau.
Le côté du contrôle peut être changé en tirat la corde à travers
le contrôle du côté opposé.
2. Pour rails avec ouveture centrale seulement. Insérez le bouchon
de plastique au milieu du rail. Ce bouchon soutiendra la corde
lors de l’installation de la poulie.
3. Attachez les cordes à la poulie. Tirez la poulie pour créer
suffi samment de tension. Marquez le point sur le mur ou le
plancher avec un crayon.
4. Enlevez les cordes et attachez la poulie au mur ou au placher.
Installez de nouveau les cordes.
La pouile drit être installée. C’est la loi. Ne pas s’y conformer
peut entreiner des blessures aux enfants ou
aux animaux fi miliers.
ÉTAPE 2 - Installing mounting hardware
1. Assemblez les attaches « assemblées » des tiges extérieures.
2. Attachez les attaches « assemblées » sur les tiges extérieures.
3. Assemblez partiellement l’attache “mise à jour” de la tige centrale.
4. Montez l’attache « centrale » sur la tige centrale et completez
l’assembiage. de l’attache.
5. Aperçu de l’attache centrale completée.
6. Toutes les attaches doivent être allignée pour l’installation du rail.
1
2
3 4
5
6
  • Page 1 1
  • Page 2 2
  • Page 3 3

Art Decor I-04-0042-BW/A Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues