Samsung 20070529160005000 Manuel utilisateur

Instruction Manual

DVD-R160

English

Français

CA

www.samsung.com/ca

AK68-01318B

100+

Getting Started

2 - English

Warning

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE THE COVER(OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

Do not install this equipment in a confined space such as a

bookcase or similar unit.

WARNING : To prevent damage which may result in fire or

electric shock hazard, do not expose this appliance to rain

or moisture.

CAUTION : DVD RECORDERS USE AN INVISIBLE

LASER BEAM WHICH CAN CAUSE HAZARDOUS

RADIATION EXPOSURE IF DIRECTED.

BE SURE TO OPERATE THE RECORDER CORRECTLY

AS INSTRUCTED.

CAUTION

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

CAUTIONS

Caution: To prevent electric shock, match wide blade of

plug to wide slot, fully insert.

Attention: Pour éviter les chocs électriques, introduíre la

lame la plus large de la fiche dans la borne correspondante

de la prise et pousser jusqu au fond.

This product satisfies FCC regulations when shielded

cables and connectors are used to connect the unit to other

equipment. To prevent electromagnetic interference with

electric appliances, such as radios and televisions, use

shielded cables and connectors for connections.

Caution: FCC regulations state that any unauthorized

changes or modifications to this equipment may

void the user's authority to operate it.

This symbol indicates that dangerous voltage

consisting a risk of electric shock is present

within this unit.

■

This unit can be used only where the power

supply is AC 120V, 60Hz. It cannot be used

elsewhere.

■

This DVD Recorder is designed and

manufactured to respond to the Region

Management Information.

If the Region number of a DVD disc does

not correspond to the Region number of

this DVD Recorder, the DVD Recorder

cannot play the disc.

■

This device is protected by U.S. Patent

Nos.4,631,603;4,577,216;4,819,098;4,907,

093; and 6,516,132.This product

incorporates copyright protection

technology that is protected by U.S. patents

and other intellectual property rights.Use of

this copyright protection technology must

be authorized by Macrovision,and is

intended for home and other limited viewing

uses only unless otherwise authorized by

Macrovision.Reverse engineering or

disassembly is prohibited.

NOTE

Getting Started

English - 3

Important Safety Instructions

Read these operating instructions carefully before using

the unit. Follow all the safety instructions listed below.

Keep these operating instructions handy for future

reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a dry cloth.

7) Do not block any ventilation openings, Install in

accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding- type plug. A polarized plug has two

blades with one wider than the other. A grounding-

type plug has two blades and a third grounding

prong. The wide blade or the third prong is provided

for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of

the obsolete outlet.

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or

when unused for long periods of time.

14) Refer all servicing to qualified service personnel.

Service is required when the apparatus has been

damaged in any way, such as the power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, Service is

also required if the apparatus has been exposed to

rain or moisture, does not operate normally, or has

been dropped.

Handling Cautions

• Before connecting other components to this

recorder, be sure to turn them all off.

• Do not move the recorder while a disc is being

played, or the disc may be scratched or broken, and

the recorder’s internal parts may be damaged.

• Do not put a flower vase filled with water or any

small metal objects on the recorder.

Precaution

• Be careful not to put your hand into the disc tray.

• Do not place anything other than the disc in the disc

tray.

• Exterior interference such as lightning and static

electricity can affect normal operation of this

recorder. If this occurs, turn the recorder off and on

again with the POWER button, or disconnect and

then reconnect the AC power cord to the AC power

outlet.

The recorder will operate normally.

• Be sure to remove the disc and turn off the recorder

after use.

• Disconnect the AC power cord from the AC outlet

when you don’t intend to use the recorder for long

periods of time.

• Clean the disc by wiping in a straight line from the

inside to the outside of the disc.

• Apparatus shall not be exposed to dripping or

splashing and no objects fi lled with liquids, such as

vases, shall be placed on the apparatus.

• The Mains plug is used as a disconnect device and

shall stay readily operable at any time.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC

power cord from the AC outlet.

• Do not use benzene, thinner, or other solvents for

cleaning.

• Wipe the cabinet with a soft cloth.

Disc Handling

• Use discs with regular

shapes. If an irregular disc

(a disc with a special

shape) is used, this DVD

Recorder may be damaged.

Holding discs

• Avoid touching the surface of a

disc where recording is

performed.

DVD-RAM, DVD±RW and DVD±R

• Clean with an optional DVD-RAM/PD

disc cleaner . Do not use cleaners or

cloths for CDs to clean DVD-

RAM/DVD±RW/DVD±R discs.

DVD-Video, CD

• Wipe off dirt or contamination on the disc with a soft

cloth.

Cautions on handling discs

• Do not write on the printed side with a ball-point pen

or pencil.

Getting Started

4 - English

• For MP3 files recorded with a VBR(Variable Bit

Rates), from 32 Kbps to 320 Kbps, the sound may

cut in out.

• Playable bitrate range is from 56Kbps to 320Kbps.

• The unit can handle a maximum of 1000 files and

folders.

•

DVD-RAM/DVD±RW/DVD±R disc recorded with

MP3 files can be played back.

• Only JPEG files with the ".jpg", ".JPG" extension can

be used.

• The unit can handle a maximum of 1000 files and

folders.

• Maximum size of progressive JPEG is 3M pixels.

• MOTION JPEG is not supported.

•

DVD-RAM/±RW/±R discs that contain JPEG files

can be played back.

• Disc : CD-R/-RW, DVD-RAM, DVD±R/ DVD±RW,

• MPEG4 File with following extensions can be

played. : .avi, .divx, .AVI, .DIVX

• MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x

• Available Audio Format : “MP3”, “MPEG”,“PCM”,

“AC3”, “DTS”

• Supported subtitle file formats: .smi, .srt, .sub,

.psb,.txt

• Use a 700MB(80 minutes) CD-R/-RW disc.

If possible, do not use a 800MB(90 minutes) or

above disc, as the disc may not play back.

• If the CD-R/-RW disc was not recorded as a closed

session, you may experience a delay in the early

playback time, and all recorded files may not play.

• Some CD-R/-RW discs may not be playable with this

unit, depending on the device which was used to

burn them.

• When recording from CDs for your personal use to

CD-R/-RW discs, playability may vary depending on

the contents and discs.

DVD±R Disc Playback and Recording

• Once a DVD±R recorded is finalized, it is playable in

a standard DVD player.

You can record onto the available space on the disc

and perform editing functions such as giving titles to

discs and programs and erasing programs before

finalizing.

• When programming is erased from a DVD±R, that

space does not become available. Once an area on

a DVD±R is recorded on, that area is no longer

available for recording, whether the recording is

erased or not.

•

It takes about 30 seconds for the unit to complete

recording management information after recording finishes.

•

This product optimizes the DVD±R for each recording.

Optimization occurs when you start recording after

inserting the disc or turning on the unit. Recording

onto the disc may become impossible if optimization is

carried out too many times.

• Do not use record cleaning sprays or antistatic. Also,

do not use volatile chemicals, such as benzene or

thinner.

• Do not apply labels or stickers to discs. (Do not use

discs fixed with exposed tape adhesive or leftover

peeled-off stickers.)

• Do not use scratch-proof protectors or covers.

• Do not use discs printed with label printers available

on the market.

• Do not load warped or cracked discs.

Disc Storage

Be careful not to damage the disc because the data on

these discs are highly vulnerable to the environment.

• Do not keep under direct sunlight.

• Keep in a cool ventilated area.

• Store vertically.

• Keep in a clean protection jacket.

• If you move your DVD Recorder suddenly from a

cold place to a warm place, condensation may

generate on the operating parts including the lens

and cause abnormal disc playback. When this

occurs, do not connect the plug to the power outlet.

Wait for two hours, then insert the disc and try to

playback again. It will work properly when

condensation has evaporated.

Disc Specifications

DVD-Video

• A digital versatile disc (DVD) can contain up to 135-

minutes of images, 8-language audio and 32 subtitle

languages. It is equipped with MPEG-2 picture

compression and Dolby 3D surround sound, allowing

you to enjoy vivid and clear theater quality images in

the comfort of your own home.

• When switching from the first layer to the second

layer of a double-layered DVD Video disc, there may

be momentary distortion in the image and sound.

This is not a malfunction of the unit.

•

Once a DVD±R/DVD-RW(V) recorded is finalized, it

is playable in a standard DVD player.

Audio CD

• An audio disc on which 44.1kHz PCM Audio is

recorded

• Plays CD-DA format audio CD-R and CD-RW discs.

The unit may not be able to play some CD-R or CD-

RW discs due to the condition of the recording.

CD-R/-RW

• Only CD-R discs with MP3 files recorded with

ISO9660 or JOLIET format can be played back

• Only MP3 files with the ".mp3", ".MP3" extension

can be used.

MP3 CD-R/-RW

JPEG CD-R/-RW

Using CD-R/-RW

Using MPEG4 disc

Getting Started

English - 5

• Playback may be impossible in some cases due to

the condition of recording.

• This unit can play back DVD±R discs recorded and

finalized with a Samsung DVD video recorder. It may

not be able to play some DVD±R discs depending

on the disc and the condition of the recording.

DVD-RW Disc Playback and Recording

• Recording and playback can be performed on DVD-

RW discs in both the Video and VR Modes.

•

Once a DVD-RW is recorded in VR or Video mode is

finalized, you cannot perform additional recording.

•

Once a DVD-RW is recorded in Video Mode and

finalized, it becomes a DVD-Video.

•

In both modes, playback can be performed before and

after finalization, but additional recording, deleting and

editing can not be performed after finalization.

• If you want to record the disc in VR Mode and then

record in V Mode, be sure to first reformat the disc.

Please be aware that formatting may erase all of the

discs content.

• When inserting an unused disc, a message will appear

asking whether to initialize the disc or not. If you select

“Yes”, the disc will be formatted in VR mode.

• DVD-RW (VR mode)

- This is a format that is used for recording data on a

DVD-RW disc. You can record multiple titles, edit,

delete, partial delete, create a playlist, etc.

- A disc that is recorded in this mode will not play in

standard DVD players.

• DVD-RW (Video mode)

-

This is a format that is used for recording data on a

DVD-RW or DVD-R disc. The disc can be played by

an existing DVD player once it has been finalized.

- If a disc that has been recorded in Video Mode by

a different maker’s recorder but has not been

finalized, it cannot be played or recorded by this

recorder.

DVD+RW Disc Playback and Recording

• With DVD+RW discs, there is no difference between

DVD-Video format (Video mode) and DVD-Video

Recording format (VR mode).

• You can make your own chapters on DVD+RWs and

edit them using the Chapter Edit menu.

• Finalizing is generally unnecessary when using a

DVD+RW disc.

DVD-RAM Disc Playback and Recording

• For cartridge type DVD-RAM discs, remove the

cartridge and use only the disc.

• Ensure that the recording mode is set to VR mode.

Otherwise, this product will not be able to play the

recording.

• You cannot play a DVD-RAM in most DVD players

due to compatibility issues.

• Only DVD-RAM standard Version 2.0 discs can be

played in this unit.

• DVD-RAM discs recorded on this unit may not work

with other DVD Players. To determine compatibility

with these DVD-RAM discs, refer to the user’s

manual for the player.

Protection

This DVD Recorder can allow you to protect the contents of

your discs, as described below.

• Program-protection: See page 62 “Locking a Title”

• Disc-protection: See page 72 “Disc Protection”

✻ DVD-RAM/DVD±RW/DVD±R discs that are incompatible

with the DVD-VIDEO format cannot be played with this

product.

✻ For more information on DVD recording compatibility,

consult your DVD-RAM/DVD±RW/DVD±R manufacturer.

✻ Use of poor quality DVD-RAM/DVD±RW/DVD±R discs may

cause the following unexpected problems including

recording failure, loss of recorded or edited materials or

damage to the recorder.

Do not use the following discs!

• LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should not

be used in this product.

• Some commercial discs and DVD discs purchased outside

your region may not be playable with this product. When

these discs are played, either “No Disc." or "The disc cannot

be played. Please check the regional code of the disc." will

be displayed.

• If your DVD-RAM/DVD±RW/DVD±R disc is an illegal copy or

is not in DVD video format, it may also not be playable.

• A 8X speed DVD+RW or greater disc can be played, but

maximum recording speed is 4X.

• Not all brands of discs will be compatible with this unit.

• The latest firmware upgrade to improve recording & playback

quality can be downloaded from our web site. (Download

Center at

www.samsung.com/ca

)

• If disc compatibility problems continue, or there is an issue

upgrading your recorder, contact the Call Center at 1-800-

SAMSUNG.

COPY PROTECTION

• Many DVD discs are encoded with copy protection. Because

of this, you should only connect your DVD Recorder directly

to your TV, not to a VCR.

Connecting your recorder to a VCR results in a distorted

picture from copy-protected DVD discs.

• This product incorporates copyright protection

technology that is protected by methods claims of certain

U.S. patents and other intellectual property rights owned

by Macrovision Corporation and other rights owners. Use

of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended

for home and other limited viewing uses only unless

otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

Disc compatibility

Getting Started

6 - English

Contents

Getting Started

Warning............................................................................2

Precaution........................................................................3

Important Safety Instructions.......................................3

Handling Cautions........................................................3

Maintenance of Cabinet...............................................3

Disc Handling...............................................................3

Disc Storage................................................................ 4

Disc Specifications.......................................................4

General Features.............................................................8

Before Reading the Instruction Manual ......................9

How to use the DVD Recorder....................................9

Unpacking......................................................................11

Accessories................................................................11

Preparing the remote control.....................................11

Tour of the Remote Control.......................................13

Description.....................................................................14

Front Panel.................................................................14

Front Panel Display....................................................14

Rear Panel.................................................................15

Connecting & Setting UP

Quick Overview..............................................................16

Step 1 : Connecting the Antenna cable ......................17

Antenna + DVD Recorder + TV : No Cable box......17

Step 2 : Connecting HDMI/ DVI to a TV......................18

Connecting to a TV with HDMI Jack........................18

Connecting to a TV with DVI Jack...........................19

Step 3 : Connecting the Video Cable..........................20

Connecting to Component Video

Input Jacks(Y,PB,PR) ..............................................20

Connecting to an S-Video Input Jack.......................21

Connecting to a Video Input Jack.............................22

Step 4 : Connecting the Audio cable..........................23

Connecting to your TV.............................................23

Connecting to a Stereo Amplifier with Analog

Input Jacks................................................................24

Connecting to an AV amplifier with a Digital

Input Jack ................................................................25

Step 5 : Connecting External Devices.......................26

Connecting a VCR, Set Top Box(STB) or DVD

Player to the AV 1 IN or S-VIDEO IN jacks............26

Connecting a Camcorder .......................................27

System Setup

Initial Setup...................................................................28

OSD Language Setup...............................................28

Using the Setup Menu................................................29

Setting up the System Options...................................29

CM Skip Time Setting...............................................29

EP Mode Time Setting..............................................30

Automatic Chapter Creation.....................................30

Quick Recording Setting...........................................31

Anynet+ (HDMI-CEC)...............................................31

Clock Set.....................................................................32

Channel Set.................................................................33

Language Setting........................................................34

Setting Up the Audio Options.....................................34

Video (Display) Setting................................................35

TV Aspect...................................................................35

Input Level.................................................................36

Black Level.................................................................36

3D Noise Reduction..................................................36

HDMI/DVI Resolution................................................36

DivX(R) Registration..................................................37

Parental Control...........................................................37

Setting the Rating Level............................................37

Changing the Password............................................37

Recording

Recordable discs.........................................................38

Compatibility between Samsung and Other

manufacturer’s Recorders.......................................38

Getting Started

English - 7

Recording Formats......................................................39

DVD-RW(Video mode)/-R........................................39

DVD-RAM/-RW(VR mode).......................................39

DVD+RW...................................................................39

Recording Mode...........................................................39

Unrecordable video......................................................39

About INFO button....................................................40

Recording from The Current TV Program you are

watching........................................................................40

Recording from External Equipment..........................41

Copying from a Camcorder.........................................42

Making a One Touch Recording (OTR).....................43

Setting a Timer Recording...........................................43

Flexible Recording (for Timer Recording only)..........44

Editing the Scheduled Record List.............................45

Deleting the Scheduled Record List...........................45

Recording the Scheduled Record List........................46

Recording on Free Space...........................................46

EZ REC MODE.............................................................47

Playback

Region code (DVD-Video only)..................................48

Logos of Discs that can be played.............................48

Disc types that can be played.....................................48

Discs that cannot be played.....................................49

Playing a Disc..............................................................49

Using the Disc Menu & Title Menu..........................50

Using the playback related buttons.........................50

Slow Motion Play......................................................50

Step Motion Play.......................................................51

Using the ANYKEY button.......................................51

Playing an Audio CD/MP3...........................................56

Playing an Audio CD(CD-DA)...................................56

Playing an MP3 Disc.................................................57

Playing Repeatedly....................................................57

Playing a Picture CD...................................................58

Playing an MPEG-4 Disc............................................59

Playing the Title List.....................................................60

Editing

Basic Editing (Title List)...............................................61

Renaming(Labeling) a Title......................................62

Locking(Protecting) a Title........................................62

Deleting a Title .........................................................63

Deleting a Section of a Title ....................................63

Editing a Chapter......................................................64

Dividing a Title ..........................................................66

Advanced Editing (Playlist)..........................................67

Creating a Playlist ....................................................67

Playing Entries in the Playlist .................................68

Renaming a Playlist Entry.......................................68

Editing a Scene for the Playlist................................69

Copying a Playlist Entry to the Playlist....................71

Deleting a Playlist Entry from the Playlist...............71

Disc Manager...............................................................72

Editing the Disc Name.............................................72

Disc Protection.........................................................72

Formatting a Disc.....................................................73

Delete All Title Lists.................................................73

Finalizing a Disc.......................................................74

Edit Compatible........................................................74

Unfinalizing a Disc (V/VR mode) ...........................75

Additional Information

Troubleshooting...........................................................76

Error Message Solutions ...........................................79

Specifications...............................................................81

Warranty.......................................................................82

Getting Started

8 - English

General Features

The DVD-R160 allows you to record and play high quality

digital video on

DVD-RAM

/

DVD±RW/DVD±R discs.

High quality digital audio and video recording

and playback

You can record up to approximately 16-hours of video on

a double side 9.4 GB DVD-RAM disc,up to 15-hours on a

dual-layer 8.5GB DVD±R disc, and up to 8-hours on a 4.7

GB DVD-RAM/DVD±RW/DVD±R disc, depending on the

recording mode.

1080P Playback

This player upconverts regular DVDs for playback on

1080p TVs.

Selectable Record Mode

You can set your recorder to one of five different recording

speeds, each varying in recording quality and length. EP

mode yields the most recording time, LP & SP modes

provide less recording time with higher quality recording,

and XP mode gives you the highest quality recording.

There's also the FR (Flexible Recording) mode that lets

you record with the best picture quality possible for the

recording time and remaining space on the disc in timer

recording.

Automated Quality Adjustment for Timer

Recording

If FR mode is selected, the video quality is adjusted

automatically so that all video for the scheduled time can

be recorded onto the free disc space. (See page 44)

Create a DVD video title using a DVD±RW/DVD±R disc

With the DVD-R160, you can create your own DVD video

title on 4.7 GB DVD±RW/DVD±R or 8.5GB DVD±R discs.

Copying data from a digital camcorder using

a DV input jack

Record digital camcorder video onto DVD-RAM,

DVD±RW or DVD±R discs using the DV input jack (IEEE

1394-4pin). (See page 42)

High quality progressive scan

Progressive scanning provides high resolution and flicker

free video.

The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry

provides the highest video playback and recording quality.

(See page 18.)

A variety of functions with an easy-to-use

user interface

The integrated menu system and the messaging function

allows you to perform desired operations both easily and

conveniently. With a DVD-RAM or DVD-RW (VR mode)

disc, you can edit recorded images, create a playlist, and

edit videos in a specific sequence according to your

requirements.

MPEG4 playback

This DVD Recorder can play MPEG4 formats within an

avi file.

DivX Certification

DivX, DivX Certified, and associated

logos are trademarks of DivXNetworks,

Inc and are used under license.

HDMI (High Definition Multimedia Interface)

HDMI reduces picture noise by allowing a pure digital

video/audio signal path from the DVD Recorder to your

TV.

EZ REC MODE

This function allows you Initialize and Finalize a disc

automatically.(see page 47)

Icon Term Definition

This involves a function available

with DVD or DVD-R/

DVD-RW (V)/+Rdiscs that have

been recorded and finalized.

This involves a function available

RAM

with DVD-RAM discs.

This involves a function available

-RW

with DVD-RW discs.

This involves a function available

-R

with DVD-R discs.

This involves a function available

+RW

with DVD+RW discs.

This involves a function available

+R

with DVD+R discs.

CD

This involves a function available

with a data CD(CD-R orCD-RW).

This involves a function available

JPEG

with CD-R/-RW or DVD-RAM/

DVD

±

RW/DVD

±

R discs.

This involves a function available

MP3

with CD-R/-RW or DVD-RAM/

DVD

±

RW/DVD

±

R discs.

This involves a function available

MPEG4

with CD-R/-RW or DVD-RAM/

DVD

±

RW/DVD

±

R discs.

This involves a case where a

Caution

function does not operate or

settings may be cancelled.

This involves tips or instructions

NOTE

on the page that help each

function operate.

One-Touch

A function that can be operated

button by using ANYKEY button.

ANYKEY A function that can be operated

button by using only one button.

Getting Started

English - 9

How to use the DVD

Recorder

Step 1

Select the disc type

Step 2

Format the disc to start recording

This unit can record on the following types of discs.

If you want to repeatedly record on the same disc

or you want to edit the disc after recording, select a

rewritable DVD

±

RW or DVD-RAM type disc.

If you want to save the recording without making

any changes, choose a non-rewritable DVD±R.

The recorder automatically starts formatting when

an unused disc is inserted. This is required for the

preparation of disc recording.

Using a DVD-RAM

This type of disc can be formatted in DVD-Video

Recording format (VR mode). You can edit

recorded video and create a playlist and edit video

in a specific sequence according to your

requirements.

Using a DVD±RW/+R

•

When an unused DVD

±

RW/+R disc is first inserted,

the message “Uninitialized Disc. Do you want to

initialize this disc?” will be displayed.

If you select Yes, initializing will begin. DVD-RW

disc can be formatted in either DVD-Video format

(Video mode) or DVD-Video Recording format (VR

mode)

•

There are no differences between DVD-Video format

(Video mode) and DVD-Video Recording format (VR

mode) with DVD+RW discs.

Using a DVD-R

When using a DVD-R disc, only V mode recording is

possible and no initialization is needed to play it on this

recorder. However, finalization is necessary to play this

disc on other DVD players.

Before Reading the

Instruction Manual

About the use of this Instruction Manual

1) Be sure to be familiarize yourself with the Safety

Instructions before using this product. (See pages 2 ~ 5)

2) If a problem occurs, check the Troubleshooting section.

(See pages 76 ~77)

may be reproduced or copied without the prior written

permission of Samsung Electronics Co.

Make sure to check the following before reading the

user’s manual.

Copyright

Icons that will be used in manual

■

You can only use either the VR or Video

mode on a DVD-RW, but not both at the

same time.

■

You can format a DVD-RW to V or VR

mode using disc manager.

It should be noted that the disc's data will

be lost when changing formats.

NOTE

DVD

Getting Started

10 - English

Step 6

Finalizing & Playing on

other DVD components

To play your DVD on other DVD components,

finalizing may be necessary. First, finish all editing and

recording operations, then finalize the disc.

When using a DVD-RW disc in VR Mode

Although finalizing is generally unnecessary when

playing the disc on a VR Mode compatible

component, a finalized disc should be used for

playback.

When using a DVD-RW disc in Video Mode

The disc should be fi nalized fi rst to enable playback

on other DVD players. No more editing or recording

can be made on the disc once it has been finalized.

When using a DVD±R disc

The disc should be fi nalized fi rst to enable playback

on other DVD players. No more editing or recording

can be made on the disc once it has been fi nalized.

Step 3

Recording

There are two different recording methods, Direct

Recording (recording a program you are currently

watching) and Timer Recording. Timer recording is

determined as a Date : MM/DD, MON-FRI, Every

SAT, etc. There are 5 recording modes: XP (high

quality mode), SP (standard quality mode), LP (long

recording mode), EP (extended mode) and FR

mode. When using FR mode to record, the picture

quality is determined by the remaining time on the

disc.

Step 4

Playing

To start playback select the title you want to play from

the title list.

A DVD consists of sections called titles, and sub

sections called chapters.

During recording, a title is created between two points

where you start and stop recording. Chapters will be

created automatically when you finalize recording on

DVD-R/DVD-RW discs in Video mode.

You can make your own chapters on DVD+RWs and

edit them using the Chapter Edit menu.

The chapter’s length (interval between chapters)

varies according to the recording mode.

Step 5

Editing a recorded disc

Editing on discs is easier than editing on conventional

video tapes. The recorder supports many different edit

functions, possible only with DVDs.

With a simple and easy edit menu, you can operate

various edit functions, such as delete, copy, rename,

lock, etc., on a recorded title.

With this recorder, you can create playlists using a

DVD-RAM/DVD-RW in VR mode. Once a playlist is

created you can create/edit a new playlist on the same

disc without changing the original recording.

■

You can finalize automatically using the EZ REC

MODE. (See page 47)

NOTE

Getting Started

Accessories

Check for the supplied accessories below.

Install Batteries in the Remote Control

•

Open the battery cover on the back of the remote.

•

Insert two AAA batteries. Make sure that the polarities

(+ and -) are aligned correctly.

•

Replace the battery cover.

If the remote control does not operate properly:

•

Check the polarity + - of the batteries .

•

Check if the batteries are drained.

•

Check if remote sensor is blocked by obstacles.

•

Check if there is any fluorescent lighting nearby.

Dispose of batteries according to local environmental

regulations. Do not put them in the household trash.

English - 11

Unpacking

Video/Audio Cable

(AC39-00073A)

RF Cable for TV

(AC39-42001J)

Batteries for Remote

Control (AAA Size)

(AC43-12002H)

Remote Control

(AK59-00061D)

Instruction Manual

(AK68-01318B)

Quick Guide

(AK68-01321B)

Preparing the Remote Control

Setting the Remote Control

You can control part of another manufacturer’s TV

functions with this remote control.

• Buttons that can be controlled on your TV :

POWER, INPUT SEL., TV VOL

+

/

-

,CH(/), TV

MUTE, 0~9, 100+.

100+

Getting Started

12 - English

To determine whether your television is

compatible, follow the instructions below.

1. Switch your television on.

2. Point the remote control towards the television.

3. Press and hold the POWER button and enter the

two-figure code simultaneously corresponding to the

brand of your television by pressing the appropriate

number buttons.

Result: If your television is compatible with the remote

control, it will switch off.

It is now programmed to operate with the remote

control.

You can then control the television using the

following buttons.

BRAND BUTTON

AIWA 82

ANAM 10, 11, 12, 13, 14, 15, 16, 17, 18

BANG & OLUFSEN 57

BLAUPUNKT 71

BRANDT 73

BRIONVEGA 57

CGE 52

CONTINENTAL EDISON 75

DAEWOO 19, 20, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34

EMERSON 64

FERGUSON 73

FINLUX 06, 49, 57

FORMENTI 57

FUJITSU 84

GRADIENTE 70

GRUNDIG 49, 52, 71

HITACHI 60, 72, 73, 75

IMPERIAL 52

JVC 61, 79

LG 06, 19, 20, 21, 22, 78

LOEWE 06, 69

LOEWE OPTA 06, 57

MAGNAVOX 40

METZ 57

MITSUBISHI 06, 48, 62, 65

MIVAR 52, 77

NEC 83

NEWSAN 68

NOBLEX 66

NOKIA 74

NORDMENDE 72, 73, 75

PANASONIC 53, 54, 74, 75

PHILIPS 06, 55, 56, 57

PHONOLA 06, 56, 57

PIONEER 58, 59, 73, 74

RADIOLA 06, 56

RADIOMARELLI 57

RCA 45, 46

REX 74

Button Function

POWER Used to switch the television on and off.

INPUT SEL. Used to select an external source.

TV VOL

+

/

-

Used to adjust the volume of the television.

CH

(/)

Used to select the desired channel.

TV MUTE Used to toggle the sound on and off.

0~9 Used to input number directly.

100+ Used to select channels over 100.

■

If several codes are indicated for your

television brand, try each one in turn until you

find one that works. If you replace the remote

control’s batteries, you must set the brand

code again.

NOTE

■

The various functions may be able to be

controlled on all televisions. If you encounter

problems, operate the television directly.

NOTE

BRAND BUTTON

SABA 57, 72, 73, 74, 75

SALORA 74

SAMSUNG 01,02,03,04,05,06,07,08,09

SANYO 41, 42, 43, 44, 48

SCHNEIDER 06

SELECO 74

SHARP 36, 37, 38, 39, 48

SIEMENS 71

SINGER 57

SINUDYNE 57

SONY 35, 48

TELEAVA 73

TELEFUNKEN 67, 73, 75, 76

THOMSON 72, 73, 75

THOMSON ASIA 80, 81

TOSHIBA 47, 48, 49, 50, 51, 52

WEGA 57

YOKO 06

ZENITH 63

Getting Started

English - 13

Tour of the Remote Control

100+

10. TV VOL Buttons

Volume adjustment.

11. MENU Button

Brings up the DVD recorder’s setup menu.

12. ENTER/DIRECTION Buttons

(UP/DOWN and LEFT/RIGHT Buttons)

This button functions as a toggle switch.

13. TITLE LIST/DISC MENU Button

Use this to enter the View Recording list/Disc menu.

14. ANYKEY Button

Use this to view the status of the disc that is being played.

15. REC Button

Use to make a recording on writable/rewritable discs.

16. REC MODE Button

Use this to set the desired Recording time and picture quality.

(XP/SP/LP/EP)

17. INFO button

This will display current setting or disc status.

18. INPUT SEL. Button

Selects line input signal in external input mode. (Tuner, AV1,

AV2 or DV)

19. EZ REC MODE Button

Use this to set the EZ REC MODE.

20. OPEN/CLOSE Button

To open and close the disc tray.

21. AUDIO Button

Use this to access various audio functions on a disc.

(DVD mode)

22. PLAY/PAUSE Button

Press to play/pause a disc.

23. CH Buttons

Use this to select a TV channel.

24. TV MUTE Button

This operates as Sound Mute. (TV mode)

25. RETURN Button

Returns to the previous menu.

26. PLAY LIST/TITLE MENU Button

Use this to return to the Title menu, or to view the recorded

Playlist.

27. EXIT Button

Exit the current menu.

28. TIMER/MARKER Button

Press to directly enter the Timer Recording Mode menu.

Use this to Bookmark or mark a position while playing a disc.

29. CANCEL Button

1. TV Button

Press this to operate your TV.

2. DVD Button

Press this to operate your DVD Recoder.

3. POWER Button

Press to power the DVD Recorder on and off.

4. NUMBER Buttons

5. 100+/CM SKIP Button

Press this to select channel 100 or higher.

Press this to skip a portion of the program automatically during

playback of a DVD disc.

6. REVERSE/FORWARD SKIP Buttons

Press to skip a disc backwards or forwards.

7. REVERSE/FORWARD STEP Buttons

Press to play frame by frame.

8. REVERSE/FORWARD SEARCH Buttons

Press to search a disc backwards or forwards.

9. STOP Button

Press to stop a disc or to stop the recording.

1

15

26

2

3

4

8

6

9

11

10

7

5

27

12

14

13

8

29

17

16

28

18

20

23

19

21

22

24

25

❋ This is a special remote control for the visually impaired, and has Braille points on the POWER ( ), STOP( )

and PLAY ( ) buttons.

Getting Started

14 - English

Getting Started

11

10

12

10

Front panel

1. POWER Button

Turns the recorder on and off.

2. AV 2 IN

Connect external equipment.

3. DV-IN

Connects external digital equipment with a DV

jack. (such as a camcorder)

4. DISC TRAY

Opens to accept a disc.

5. P.SCAN Button

Selects the progressive scan mode.

6. OPEN/CLOSE Button

Opens and closes the disc tray.

7. DISPLAY

Displays the playing status, time, etc.

8. CH ( )

Select TV channels.

9. REC

Starts recording.

10. SEARCH

Go to the next title/chapter/track, or go back to

the previous title/chapter/track.

11. STOP

Stops disc playback.

12. PLAY/PAUSE

Plays a disc or pauses playback.

Description

Front Panel Display

1. Lights when a disc is loaded.

2. Lights in the record mode.

3. Lights to indicate the timer record mode.

4. Lights when a DVD-RAM/DVD

±

RW/DVD

±

R disc

is loaded.

5. Alpha/Numeric display.

6. Lights in the progressive scan mode.

Getting Started

English - 15

Getting StartedGetting Started

11

Rear Panel

1. ANT IN/ANT OUT (TO TV)

Connect antenna cables.

2. DIGITAL AUDIO OUT(OPTICAL)

Connects to an amplifier having a digital optical

audio input jack.

3. DIGITAL AUDIO OUT(COAXIAL)

Connects to an amplifier having a digital coaxial

audio input jack.

4. AV AUDIO OUT

Connect to the audio input of external equipment

using audio cables.

5. AV VIDEO OUT(good video quality)

Connects the input of external equipment using a

Video cable.

6. AV S-VIDEO OUT(better video quality)

Connects the input of external equipment using an

S-Video cable.

7. COMPONENT VIDEO OUT(excellent video quality)

Connect to equipment having Component video

input jacks.

8. AV 1 AUDIO IN

Connect the output of external equipment using

audio cables

9. AV 1 VIDEO IN

Connects the output of external equipment using a

video cable.

10. AV 1 S-VIDEO IN

Connects the output of external equipment using

an S-Video cable.

11. HDMI OUT(best video quality)

Connects the input of external equipment using a

HDMI cable.

■

The Antenna connection does not pass

audio/video signals. To watch a DVD on your

TV, you must connect audio/video cables.

NOTE

Connecting &

Setting Up

16 - English

Connecting &

Setting Up

This section involves various methods of

connecting the DVD Recorder to other external

components and setting required initial modes.

Quick Overview

A Quick Overview presented in this guide will give

you enough information to start using the recorder.

Quick Overview..................................................................16

Step 1 : Connecting the Antenna Cable .........................17

Step 2 : .Connecting HDMI/ DVI to a TV.........................18

Step 3 : Connecting the Video Cable...............................20

Step 4 : Connecting the Audio Cable............................ .23

Step 5 : Connecting External Devices............................26

Step 1 : Connecting the Antenna Cable

†

Step 2 : Connecting HDMI/ DVI to a TV

†

Step 3 : Connecting the Video Cable

†

Step 4 :Connecting the Audio Cable

†

Step 5 : Connecting External Devices

•

Note to CATV system installer: : This reminder is

provided to call CATV system installer’s attention to

Article 820-40 of the National Electrical Code

(Section 54 of Canadian Electrical Code, Part I),

that provides guidelines for proper grounding and,

in particular, specifies that the cable ground shall

be connected to the grounding system of the

building as close to the point of cable entry as

practical.

Step 1: Connecting the Antenna Cable

There are several ways to connect your DVD Recorder. Select the antenna connection that best suits you below.

Antenna + DVD Recorder + TV : No Cable box

You can record non-scrambled channels by selecting the channel on the DVD Recorder. Also use this method if you

watch channels without cable box.

■

The VHF/UHF ANT (RF) OUT jack of this

product sends only signals received through

the antenna. It does not output Audio/Video

signals. You must connect Audio/Video cables

to view Video from the unit.

(i.e. DVD playback)

NOTE

Connecting &

Setting Up

English - 17

Connecting &

Setting Up

18 - English

Step 2 : Connecting HDMI/DVI to a TV

If your TV has a HDMI/DVI input, connect the HDMI/DVI cable to the TV. You will enjoy the best quality image and

sound.

Connecting to a TV with an HDMI Jack

Using an HDMI-HDMI cable (not included), connect the HDMI OUT jack on the rear of the DVD Recorder to the HDMI

IN jack of your TV. Press the input selector on your TV remote control until the HDMI signal from the DVD Recorder

appears on your TV screen.

HDMI OUT

Caution

■

To watch through the HDMI output, set the digital audio

output to PCM. (See page 34-35)

■

Depending on the HDMI device(TV/HDMI Receiver) you use,

audio may not be supported. If your TV does not support

Dolby digital/DTS, Audio output is not available when you set

the Digital output to Bitstream or select DTS On in the Audio

setup menu. In this case, set the digital audio output to PCM

or DTS Off.

■

If you use an HDMI cable to connect a Samsung TV to the

DVD recorder, you can operate the recorder using the TV

remote control. (This is only available with SAMSUNG TVs

that support Anynet + (HDMI-CEC). ) (See pages 31)

■

Please check the logo (If you TV has an

logo,then it supports Anynet+ function.)

■

The DVD-R160 supports 1080p resolution. This is only

available when an HDMI cable is connected to a TV that

supports 1080p resolution.

Connecting &

Setting Up

English - 19

Connecting to a TV with a DVI Jack

Using an HDMI-DVI cable (not included), connect the HDMI OUT terminal on the rear of the DVD Recorder to the DVI

IN terminal of your TV.

An HDMI to DVI connection requires a separate audio connection, using the audio cables, connect the AUDIO (red

and white) OUT terminals on the rear of the DVD Recorder to the AUDIO (red and white) IN terminals of your TV.

Turn on the DVD Recorder and TV.

Press the input selector on your TV remote control until the DVI signal from the DVD Recorder appears on your TV

screen.

HDMI OUT

■

To set the HDMI output resolution(480p/720p/1080i)(see

page 36)

■

HDMI (High Definition Multimedia Interface)

HDMI enables you to make a digital video and audio

connection with a single cable.

Using HDMI, the DVD player transmits a digital video and

audio signal and displays a vivid picture on a TV having an

HDMI input jack.

■

HDMI is completely compatible with DVI. The only

difference between HDMI and DVI is that HDMI supports

multi-channel audio.

■

HDMI connection description

HDMI connector - Both uncompressed video data and

digital audio data (LPCM or Bit Stream data).

- The DVD recorder outputs a pure digital signal to the TV.

- If your TV does not support HDCP (Highbandwidth Digital

Content Protection), snow noise appears on the screen.

■

Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal.

However, when playing a DVD, the data transmitted to a

TV is digital. Therefore either a digital-to-analog converter

(in the DVD Recorder) or an analog-to-digital converter (in

the TV) is required. During this conversion, the picture

quality is degraded due to noise and signal loss. HDMI

technology is superior because it requires no D/A

conversion and is a pure digital signal from the DVD

recorder to your TV.

■

What is the HDCP?

HDCP (High-bandwidth Digital Content Protection) is a

system for protecting DVD content output via HDMI from

being copied. It provides a secure digital link between a

video source (PC, DVD. etc) and a display device (TV,

projector. etc). Content is encrypted at the source device

to prevent unauthorized copies from being made.

NOTE

Connecting &

Setting Up

20 - English

Connecting &

Setting Up

Connecting &

Setting Up

DVD-R160

1. Connect Component video cables(not supplied)

between the COMPONENT OUT(Y,PB,PR) jacks on

DVD Recorder and COMPONENT IN(Y,PB,PR) jacks

on your TV (or AV amplifier). This connection outputs

the 480i or 480p resolution to your TV

2. If the connected TV supports Progressive Scan,

press the P.SCAN button on the front of the DVD

Recorder to enjoy best quality video.

Pressing the P.SCAN button switches Progressive

(480p) / Interlace (480i) scan mode on.

• You will enjoy the best quality accurate color

reproduction images. Component video separates the

picture element into black and white(Y), blue(P

B), and

red(PR) signals to present clear and clean images.

• Connect the audio cables(white and red) between the

AUDIO OUT jacks on the DVD Recorder and AUDIO

IN jacks on your TV(or AV amplifier).

(See pages 23-25)

■

Compared to standard interlaced video, progressive

scan doubles the amount of video lines fed to your

TV, resulting in a clearer, more stable, and flicker

free image than interlaced video. The component

output jack of the DVD player can be used for

progressive output mode, which is only available

with TVs that support progressive scan.

■

Progressive Scan Output (480p).

Not all high definition television sets are fully

compatible with this product. If the 480p progressive

scan picture is not satisfactory, press the P.SCAN

button on the unit to switch to the Interlace mode.

If there are questions regarding TV set compatibility

with this model, please contact our customer

service center at 1-800-SAMSUNG.

■

The Component jacks will not output video

resolutions above 480p. To view 720p,1080i and

1080p, connect the DVD-R160 to your TV an HDMI-

HDMI cable. With HDMI connected, press the

P.SCAN button to alternate between all available

resolutions. (See page 36)

NOTE

Step 3 : Connecting the Video Cable

There are several ways to connect your DVD Recorder. Select one of the video connections on the following pages.

You must use one of the following audio/video connections on this unit.

Connecting to Component video input jacks (Y,PB,P

R)

Component cable

(not supplied)

La page est en cours de chargement...

Samsung 20070529160005000 Manuel utilisateur

Samsung 20070529160005000 Manuel utilisateur

Documents connexes

Autres documents