EnOcean PTM 535 Manuel utilisateur

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

Patent protected:

WO98/36395, DE 100 25 561, DE 101 50 128,

WO 2004/051591, DE 103 01 678 A1, DE 10309334,

WO 04/109236, WO 05/096482, WO 02/095707,

US 6,747,573, US 7,019,241

Observe precautions! Electrostatic sensitive devices!

PTM 535 / PTM 535U / PTM 535J

EnOcean Transmitter Module

21.09.2020

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

REVISION HISTORY

The following major modifications and improvements have been made to this document:

Version

Author

Reviewer

Date

Major Changes

1.0

MKA

23 May 2018

Initial Release

1.1

MK/CB

CB

02 Aug 2018

Configuration set and functional block

diagram updated, additional minor

changes e.g. ARIB ID added, Tx range

free field 300m

1.2

MK/CB

CB

14 Sep 2018

Renamed Pad 13 from VCC to

VCC_MODE, V+ for configuration only,

hint for PTM Config help

1.3

MK/CB

CB

21 Nov 2018

4.4 added strict sequence and tool re-

quirements for configuration change,

2.3 added CFG test pin

1.4

MK/CB

CB

27 May 2019

Document branding changed, 2.2 pin out

image corrected

1.5

MKA

21 Sep 2020

FCC / ISED added

Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany

www.enocean.com, info@enocean.com, phone +49 (89) 6734 6890

Important!

This information describes the type of component and shall not be considered as assured

characteristics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry

and specifications are subject to change without notice. For the latest product specifica-

tions, refer to the EnOcean website: http://www.enocean.com.

As far as patents or other rights of third parties are concerned, liability is only assumed for

modules, not for the described applications, processes and circuits.

EnOcean does not assume responsibility for use of modules described and limits its liability

to the replacement of modules determined to be defective due to workmanship. Devices or

systems containing RF components must meet the essential requirements of the local legal

authorities.

The modules must not be used in any relation with equipment that supports, directly or

indirectly, human health or life or with applications that can result in danger for people,

animals or real value.

Components of the modules are considered and should be disposed of as hazardous waste.

Local government regulations are to be observed.

Packing: Please use the recycling operators known to you.

 
USER MANUAL 
 
 
 
PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE 
 
© 2019 EnOcean  |  www.enocean.com   F-710-017, V1.0        PTM 535 / 535J User Manual  | v1.5 | September 2020 |  Page 3/36 
 
TABLE OF CONTENT 
 
General description ........................................................................................ 5 
1 Product description ........................................................................................ 5 
2 Product variants ............................................................................................ 5 
3 Technical data ............................................................................................... 6 
4 Maximum ratings for input signals ................................................................... 6 
5 Physical dimensions ....................................................................................... 6 
6 Device drawing ............................................................................................. 7 
7 Environmental conditions ............................................................................... 8 
8 Ordering information ..................................................................................... 8 
Functional description .................................................................................... 9 
1 Functional Principle ........................................................................................ 9 
2 Block diagram ............................................................................................... 9 
3 Interface pin layout ..................................................................................... 10 
4 Interface pin functionality ............................................................................. 11 
Radio telegram format ................................................................................. 12 
1 Standard mode ........................................................................................... 12 
2 Enhanced security mode .............................................................................. 14 
3 Switching between operation modes .............................................................. 15 
4 Transmission timing ..................................................................................... 15 
PTM 535 configuration ................................................................................. 16 
1 PTM 535 configuration parameters ................................................................ 16 
2 PTM 535 configuration interface .................................................................... 17 
3 PTM 535 test point location ........................................................................... 17 
4 Connection between Segger J-Link and PTM 535 ............................................. 18 
4.1  Segger power supply (6-Pin interface) .................................................... 18 
4.2  External power supply (4 pin configuration interface) ............................... 19 
5 Required tools ............................................................................................. 20 
6 Configuration setup ..................................................................................... 21 
7 User Interface ............................................................................................. 21 
8 Execution sequence ..................................................................................... 22 
Application information ................................................................................ 23 
1 Connection to ECO 200 energy harvester ....................................................... 23 
2 How to populate a teach-in button (for enhanced security mode) ...................... 23 
3 Antenna specification ................................................................................... 24 
4 Layout recommendations ............................................................................. 25 
5 Transmission range ..................................................................................... 26 
Regulatory information ................................................................................. 27 
1 RED (European Union) ................................................................................. 27 
2 FCC (United States) ..................................................................................... 28 
2.1  FCC grant of equipment authorization .................................................... 28 
2.2  FCC regulatory statement ..................................................................... 29 
3 ISED (Canada) ............................................................................................ 30 
3.1  ISED technical acceptance certificate...................................................... 30 
3.2  ISED regulatory statement .................................................................... 32 
3.2.1  English version ................................................................................. 32 
3.2.2  French version .................................................................................. 33 
4 ARIB (Japan) .............................................................................................. 34 

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

6.4.1 ARIB (Japan) certificate ........................................................................ 34

6.4.2 ARIB (Japan) regulatory requirements .................................................... 35

7 Product history ............................................................................................ 36

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1 General description

1.1 Product description

The radio transmitter module PTM 535, PTM 535U and PTM

535J from EnOcean enable the implementation of wireless

sensors and switches without batteries.

Key applications are handheld remote controls or industrial

switches.

1.2 Product variants

The following product variants are offered:

◼ PTM 535

Operating frequency 868.300 MHz

◼ PTM 535U

Operating frequency 902.875 MHz

◼ PTM 535J

Operating frequency 928.350 MHz

All three variants contain a pre-installed whip antenna, support enhanced security and are

delivery in a cardboard box. The term “PTM 535” is subsequently used to describe all three

product variants unless otherwise noted.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.3 Technical data

Power supply ECO 200 or equivalent energy pulse

Antenna Pre-installed whip antenna

Frequency / Modulation / Transmission power

PTM 535 868.300 MHz / ASK / +5 dBm

PTM 535U 902.875 MHz / FSK / +4 dBm

PTM 535J 928.350 MHz / FSK / +0 dBm

Data rate 125 kbps

Telegram type RPS Type 2

SEC (Encrypted and authenticated transmission)

Digital inputs 4 (2 of those also usable via meander contacts)

Mode selection (standard / enhanced security) 3 pins / LRN Button

Transmission range up to 300 m free field, up to 30 m indoor

1.4 Maximum ratings for input signals

Symbol

Parameter

Min

Max

Units

AC1, AC2

Supply voltage operation

0

6.0

V

V+

Supply voltage configuration

0

5.5

V

GND

Voltage on GND pin

0

V

A0, A1, B0, B1,

SECURE, STANDARD, CFG

Voltage on digital input pins

0

3.6

V

1.5 Physical dimensions

PCB dimensions 26.2 x 21.15 x 3.5 mm

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.6 Device drawing

Figure 1 – PTM 535 outline

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.7 Environmental conditions

Operating temperature -25 °C … +65 °C

Storage temperature -40 °C … +85 °C

Storage temperature in Tape & Reel -20 °C … +50 °C

Humidity 0% … 93% r.h., non-condensing

1.8 Ordering information

Type

Ordering

Code

Frequency

Note

PTM 535

S3001-A535

868.300 MHz

Whip antenna, Delivered in cardboard box

PTM 535U

S3051-A535

902.875 MHz

Whip antenna, Delivered in cardboard box

PTM 535J

S3061-A535

928.350 MHz

Whip antenna, Delivered in cardboard box

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2 Functional description

2.1 Functional Principle

PTM 535 is designed to be powered by an ECO 200 kinetic energy harvester from EnOcean.

PTM 535 can be mechanically connected to the contact springs of ECO 200 by means of its

integrated PCB contacts.

PTM 535 provides 4 digital input pads and two PCB meander structures allowing the imple-

mentation of push button functions either via external connection or via conductive rubber

pads.

When the ECO 200 harvester generates an energy pulse or when power is supplied by an-

other source then PTM 535 determines the polarity of the energy pulse (push or release

direction), and the operating status of the digital inputs and encodes this information in an

RF telegram.

The communication mode (enhanced security communication or standard communication)

can be selected using the SECURE and STANDARD input pins or the LRN button (which is

not mounted by default). Default communication mode is STANDARD.

2.2 Block diagram

Figure 2 below shows the block diagram of PTM 535.

Figure 2 – PTM 535 functional block diagram

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2.3 Interface pin layout

Figure 3 below shows the pin out and external interfaces of PTM 535 as seen from the top

(component side). Items marked in green are on the component side while items in grey

are on the bottom side.

In addition to the 16 boundary contacts, PTM 535 provides the following contact points:

◼ Meander contact A0

◼ Meander contact A1

◼ Connection for whip antenna RF_WHIP

◼ Footprint for LEARN button (connecting VCC and SEC)

◼ AC1 / AC2 power supply connection to ECO 200 harvester

(two contact pairs at the PCB bottom side to support different ECO 200 orientation)

Figure 3 – PTM 535 pin-out and external interfaces

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2.4 Interface pin functionality

Table 1 below describes the PTM 535 interface pin functionality.

Function

Characteristics

GND

Ground connection

Must be connected to GND

VCC_MODE

Internal Operating

voltage with 1k

Connect externally to SECURE or STANDARD pin to

change operation mode.

Also connected to LEARN button pad.

SECURE

Mode change pin

Connect this pin to VCC_MODE and press the ECO 200

harvester to change operation mode to enhanced secu-

rity. Then disconnect.

Also connected to LEARN button footprint.

STANDARD

Mode change pin

Connect this pin to VCC_MODE and press the ECO 200

harvester to change operation mode to standard.

Then disconnect.

B0

O-Button Rocker B

Digital input, leave open or connect to GND

Internal pull-up

B1

I-Button Rocker B

Digital input, leave open or connect to GND

Internal pull-up

A0

O-Button Rocker A

Digital input, leave open or connect to GND

Internal pull-up, Connected to meander contact

A1

I-Button Rocker A

Digital input, leave open or connect to GND

Internal pull-up, Connected to meander contact

AC1

ECO 200 Input 1

ECO 200 or equivalent energy pulse

AC2

ECO 200 Input 2

ECO 200 or equivalent energy pulse

RF_WHIP

RF output

Output for whip antenna

RF_50

RF output

50 Ohm output for external antenna

CFG

Test pin

Do not connect

Table 1 – PTM 535 interface pin functionality

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

3 Radio telegram format

3.1 Standard mode

In standard configuration, PTM 535 transmits the same telegram type as the PTM 210

pushbutton module. The telegram information is encoded within a 7 byte RPS telegram as

shown in Figure 4 below.

Figure 4 – PTM 535 telegram format

This telegram format uses the following fields:

◼ Telegram type (RORG, 1 byte)

The telegram type is always 0xF6 indicating an RPS telegram

◼ Switch data (DATA, 1 byte)

This field encodes the buttons that have been pressed. The encoding depends on the

number of buttons that have been pressed.

◼ EnOcean Unique Radio IO (EURID, 4 byte)

This field contains the ID which uniquely identifies each EnOcean products

◼ Switch status (STATUS)

This field encodes certain properties of the telegram as shown in below.

The STATUS field identifies the message type (U-Message or N-Message) as well as the

repeater level (original telegram, 1 hop repeated, 2 hop repeated) as shown in Figure 5

below.

Figure 5 – STATUS field encoding

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

If one or two buttons are pressed, then the button status is transmitted using a so-called

N-Message. The DATA field format of such N-Message is shown in Figure 6 below.

Figure 6 – DATA field encoding for N-Messages (one or two button presses)

If either no button is pressed (only the ECO 200 is actuated), three buttons are pressed or

four buttons are pressed then the button status is transmitted using a so-called U-Message.

The DATA field format of such N-Message is shown in Figure 7 below.

Figure 7 – DATA field format for U-Messages (no, three or four button pressed)

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

3.2 Enhanced security mode

While operating in enhanced security mode, PTM 535 sends secure telegrams in accordance

to EEP D2-03-00 as specified in EnOcean Equipment Profiles. For more details refer

to http://www.enocean-alliance.org/eep/.

These telegrams include a rolling code based on an incrementing counter which guarantees

that identical message content will be encrypted differently for each telegram thus prevent-

ing replay attacks.

The initial counter value is transmitted from PTM 535 to the receiver as part of the teach-in

telegram when entering secure mode. Subsequent secure telegrams do not specify this

counter value; therefore sender and receiver have to automatically increment their respec-

tive counters for each secure telegram to keep them synchronized.

When telegrams are not received by the receiver this may lead to a de-synchronization of

transmitter and receiver counters, i.e. the transmitter counter will have a greater value

than the receiver counter.

In order to prevent failure, the receiver will usually test the received rolling code against a

defined window of future expected rolling codes and – if successful - resynchronize its

counter automatically. The size of this rolling code window is defined on the receiver side.

It is important that the amount of consecutive, non-received telegrams does not exceed the

side of this window.

For more details please refer to http://www.enocean.com/en/security-specification/.

The rolling code is not transmitted with every telegram. It is only transmitted dur-

ing teach-in. Afterwards the receiver has to increase the counter autonomously for

each received message.

It is strongly recommended to use PTM 535 in secure mode only in fixed installa-

tions with safe radio distance to avoid de-synchronization of sender and receiver.

De-synchronization will occur if PTM 535 is operated outside the range of the re-

ceiver consecutively more often than the size of the rolling code window defined

on the receiver.

The same may apply if consecutive telegrams are lost on the receiver side due to

power interruptions.

In these cases it is necessary to set the receiver in LRN mode and teach-in the

device again.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

3.3 Switching between operation modes

PTM 535 can be switched from standard mode (default) to enhanced security mode by con-

necting SECURE with VCC_MODE (see chapter 3 for details) and triggering the ECO 200.

Upon entry into enhanced security mode, a teach-in telegram is sent by PTM 535. The type

of the teach-in telegram (Teach_In_Info : Type) is: 1-PTM.

PTM 535 will continue to transmit secure teach-in telegrams until the SECURE pin is discon-

nected from the VCC_MODE pin.

The secure teach-in message has to be transmitted as two consecutive telegrams due to its

payload size. Therefore, the ECO generator has to be triggered twice in order to transmit a

complete secure teach-in message. It is not required that the two contacts (SECURE and

VCC_MODE) remain connected throughout the transmission of both messages. It is suffi-

cient to connect them while actuating the ECO energy generator the first time.

For more information on the structure of the teach-in telegram please refer to chapter 4.2

of http://www.enocean.com/en/security-specification/.

PTM 535 can be switched from secure mode to normal mode by connecting STANDARD with

VCC_MODE and triggering the ECO 200. Then disconnect the pins.

Before changing the operating mode please make sure to clear the device from all

receivers which have been taught to work with this device before. Otherwise the

receiver will ignore the telegrams and the application will not work.

3.4 Transmission timing

The setup of the transmission timing allows avoiding possible collisions with data packages

of other EnOcean transmitters as well as disturbances from the environment. With each

transmission cycle, 3 identical subtelegrams are transmitted within 40 ms.

The transmission of a subtelegram lasts approximately 0.7 ms. The delay between the

three transmission bursts is affected at random.

PTM 535 transmits in secured mode 2 identical subtelegrams with length of ~ 1.3 ms

PTM radio modules are designed for manual button operation. The actuation rate

should therefore be limited to no more than 5 actuations per second.

For higher actuation rates, PTM radio modules might temporarily stop operation

and will restart operation after a period of 2 seconds without operation.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

4 PTM 535 configuration

PTM 535 provides a configuration interface that can be used to configure certain device

parameters.

4.1 PTM 535 configuration parameters

The following parameters can be configured for PTM 535 (868.300 MHz):

◼ Content of the radio telegrams

This can be configured for each of the 32 possible input combination (A0, A1, B0,

B1, direction of ECO movement)

◼ Default operation mode

This can be standard (default) or enhanced security. Changing the mode is still pos-

sible using the HW mechanism described in chapter 3.3

◼ Secure teach-in telegram transmission

The secure teach-in telegram transmission can start only when the ECO 200 is

pressed, only when the ECO 200 is released or at any ECO 200 action (press or re-

lease)

◼ Number of secure subtelegrams

If PTM 535 is powered by an ECO 200 harvester and operating in enhanced security

mode then it will always transmit 2 subtelegrams.

If PTM 535 is powered by another energy source such as a battery and operating in

enhanced security mode, then it can be selected if it should transmit 2 or 3 subtele-

grams.

Note that configuration is currently only supported for PTM 535 (868.300 MHz).

Configuration of PTM 535U (902.875 MHz) and PTM 535J (928.350 MHz) is cur-

rently not supported.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

4.2 PTM 535 configuration interface

The PTM 535 configuration interface consists of test points MP1- MP6. The function of these

test points is summarized in Table 2 below.

Table 2 – PTM 535 configuration interface

4.3 PTM 535 test point location

Figure 8 below shows the location of the test points MP1 … MP6. For the exact location

refer to the product drawing in chapter 1.6.

Figure 8 – PTM 535 test point location

Pad

Signal

Name

Characteristics

Segger

J-Link Signal

Segger

J-Link Pin

MP1

VCC

Configuration interface

(Supply voltage)

VTref

1

MP2

GND

Configuration interface

(Ground)

GND

4/6/8/10

/12

MP3

TDIO

Configuration interface

(Data)

TMS

7

MP4

TCK

Configuration interface

(Clock)

TCK

9

MP5

V+

Power supply (from Segger)

5V-Supply

19

MP6

RESET

Optional

RESET

15

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

4.4 Connection between Segger J-Link and PTM 535

PTM 535 has to be connected to the Segger J-Link connector for configuration. Figure 9

below shows the pin-out of the Segger J-Link connector.

Figure 9 – Segger J-Link connector pin-out

Two approaches can be used to connect Segger J-Link and PTM 535 depending on the pow-

er supply of PTM 535 during configuration. Both approaches are described below.

4.4.1 Segger power supply (6-Pin interface)

Supplying power by Segger J-Link to PTM 535 is the recommended approach. It requires a

6 pin test interface.

In this case, power is supplied by Segger J-Link to PTM 535 via PTM 535 MP5 (V+) con-

nected to Segger Pin 19. The “5V Target Power Supply” option has to be activated at the

Segger user interface. We recommend checking available voltage supply.

The required connections are shown in Figure 10 below.

Figure 10 – 6-Pin configuration interface (Power supplied by Segger)

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

4.4.2 External power supply (4 pin configuration interface)

This approach allows you to use a 4 needle test adapter instead of a 6 needle adapter.

Existing 4 needle adapters built for PTM 335 can be reused.

It requires to supply PTM 535 by an external power supply (2.0 - 3.3 V) connected to PTM

535 MP1 and to Segger VTref (IO voltage reference). The external power supply ground has

to be connected to PTM 535 MP2 (GND) and Segger GND.

The required connections are shown in Figure 11 below.

Figure 11 – 4-Pin configuration interface (external power supply)

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

4.5 Required tools

The following tools are required to configure PTM 535:

◼ Needle adapter

Suitable adapter to contact test points as described in the previous chapter.

EnOcean can provide a mechanical design example upon request.

◼ Debugger / Programmer

J-Link Plus or higher from Segger is required, see:

https://www.segger.com/products/debug-probes/j-link/models/j-link-plus/

◼ J-Link Software and Documentation Pack

https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack

◼ PTM 535 Configuration Suite

http://www.enocean.com/en/download/

Please check PTM 535 Config help for a detailed description of the program usage.

PTM 535 Configurator uses Segger tools to communicate with the radio chip. If a

window pops up “to unlock” the device you must select NO (details see PTM 535

Config help). Due to radio approval requirements a wrong configuration will lead

the module to stop radio transmission.

Radio module configuration is only possible with the EnOcean PTM 535 Configu-

rator tool. Follow exactly the below written sequence to chance PTM 535 config-

uration. Due to radio approval requirements, a wrong configuration will lead the

module to stop radio transmission.

Additional care has to be taken to configure correct values for DATA and STATUS

fields. Otherwise PTM 535 might not work properly together with repeaters or

receivers.

La page charge ...

EnOcean PTM 535 Manuel utilisateur

Ce manuel convient également à

EnOcean PTM 535 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents