Haier H21BFC45NS Manuel utilisateur

User Manual

H21BFC45N

Guide de l’Utilisateur

H21BFC45N

Manual del Usuario Modelo

H21BFC45N

Cabinet Depth Refrigerator

Réfrigérateur avec portes à

vantaux

Refrigerador con la profundidad

de los gabinetes

1

English

table of contents

PAGE

Safety Precautions ...................................................................2-3

Energy Saver Instructions .......................................................... 3

Installing Your Refrigerator ....................................................4-5

Parts & Features ......................................................................... 6

Removing and Installing the Doors .......................................7-8

Connecting the Water Supply Line .......................................9-10

Preparation before Use ............................................................11

Initial Usage .............................................................................. 11

Setting the Control Functions ............................................. 12-17

Food Storage Tips ............................................................... 18-20

About the Freezer ............................................................... 20-21

Usage of Ice Maker ............................................................ 21-23

Defrosting, Cleaning .................................................................24

Changing Water Filter ..............................................................25

Shutting off the Refrigerator ...................................................26

Troubleshooting .................................................................. 27-34

Limited Warranty ......................................................................35

IMPORTANT SAFETY

PRECAUTIONS

Read all of the instructions before using this appliance.

When using this appliance, always exercise basic safety

precautions, including the following:

1. Use this appliance only for its intended purpose as described in this use

and care guide.

2. This refrigerator must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions

in the installation section.

3. Never unplug your refrigerator by pulling on the power cord. Always

grasp the plug firmly and pull straight out from the outlet.

4. Repair or replace all electric service cords that have become frayed or

otherwise damaged immediately. Do not use a cord that

shows cracks or abrasion damage along its length, the plug, or

the connector end.

5. Unplug your refrigerator before cleaning or before making any repairs.

Note: If for any reason this product requires service, we strongly

recommend that a certified technician perform the service.

6. Do not use any electrical device or sharp instrument in defrosting

your refrigerator.

7. If your old refrigerator is not being used, we recommend that you

remove the doors. This will reduce the possibility of danger to children.

8. After your refrigerator is in operation, do not touch the cold surfaces

in the freezer compartment, particularly when hands are damp or wet.

Skin may adhere to these extremely cold surfaces.

9. Do not refreeze foods that have been thawed completely. The

United States Department of Agriculture in Home and Garden Bulletin

No. 69 reads: “…You may safely refreeze frozen foods that have

been thawed if they still contain ice crystals or if they are cold—

below 40° F.”

“… Thawed ground meats, poultry, or fish that have any off-odor or

off-color should not be refrozen and should not be eaten. Thawed ice

cream should be discarded. If the odor or color of any food is poor or

questionable, discard it. The food may be dangerous to eat.”

“…Even partial thawing and re-freezing reduce the quality of foods,

particularly fruits, vegetables, and prepared foods. The eating quality

of red meats is affected less than that of many other foods. Use refrozen

food as soon as possible, to save as much of its eating quality as you

can.”

10. Do not operate your refrigerator in the presence of explosive

fumes.

2

English

3

DANGER

Risk of child entrapment. Before you throw away your old refrig-

erator or freezer, take the doors off. Leave the shelves in place so

that children cannot easily climb inside.

Thank you for purchasing our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your refrigerator.

Remember to record the model and

serial number. They are on a label

inside of the refrigerator.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

SAVE THESE INSTRUCTIONS

HOUSEHOLD USE ONLY

IMPORTANT

ENERGY SAVER INSTRUCTIONS

*This product is equipped with energy saver feature. The

refrigerator is shipped with the energy saver feature enabled.

Over time, moisture can form on the front surface of the

refrigerator cabinet and cause rust. If moisture does appear on the

front surface of the refrigerator cabinet, horizontal mullion or top

of freezer drawer, turn off the energy saver feature by following

the instruction on page 16.

English

installing your refrigerator

4

Note: Refrigerator is for freestanding purpose.

Unpacking Your Refrigerator

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the refrigerator accessories inside and outside. Slide out and

remove plastic or foam guard used to secure the compressor from shipping

damage due to vibration and shock.

2. Inspect and remove any remains of packing, tape or printed materials before

powering on the refrigerator.

Proper Air Circulation

• To ensure that your refrigerator works at the maximum efficiency it was

designed for, you should install it in a location where there is proper air

circulation, plumbing and electrical connections.

• The following are recommended clearances around the

refrigerator:

Sides……………3/4 "(19mm)

Top....................1" (25mm)

Back..................1" (25mm)

Electrical Requirements

• Make sure there is a suitable power outlet (115 volts, 15 amps outlet) with

proper grounding to power the refrigerator.

• Avoid the use of three-plug adapters or cutting off the third grounding in order

to accommodate a two-plug outlet. This is a dangerous practice since it

provides no effective grounding for the refrigerator and may result in

shock hazard.

English

5

Use of Extension Cord

• Avoid the use of an extension cord because of potential safety hazards under

certain conditions. If it is necessary to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding plug and a 3-slot outlet that will

accept the plug. The marked rating of the extension cord must be equal to, or

greater than, the electrical rating of the appliance.

Install Limitations

• Do not install your refrigerator in any location not properly insulated or heated,

e.g. garage etc. Your refrigerator was not designed to operate in temperature

settings below 55˚ Fahrenheit.

• Select a suitable location for the refrigerator on a hard, even surface away

from direct sunlight or heat source, e.g. radiators, baseboard heaters, cooking

appliances etc. Any floor unevenness should be corrected with the leveling legs

located on the front bottom corners of the refrigerator.

English

6

Parts & features

Note: When reviewing this manual for your features some models may

differ in appearance from what is shown in the manual.

Fresh food storage floodlight

Fresh Food Section

Freezer Section

Water filter

Dairy product

stored here

Glide Shelf

Gallon Door Bin

Meats, fruit and

vegetable crispers

Full-width pantry

Deep freeze

lower drawer

Upper storage bin

Lower storage basket

Ice cube bin

Disconected the cable,crew out the earth line.Disconected the

water pipe on the back at the same time,pull out the pipe from

the cabinet,then take the door off.(only PBFS21* and PRFS25*)

English

7

reMoVing anD installing tHe Doors

You may not need to remove the doors, but if you have trouble getting the unit

into its final location, please follow the below door removal and installation

instructions. It is suggested, for your safety, to have two or more people to assist

you in completing the below task to avoid bodily injury, product damage, or

property loss.

Right French Door Removal and Installation

1. Remove the screws on the top hinge cover, then set aside the top hinge cover

and lay it down for installing later.

2. Using a screwdriver, remove the top hinge screws. Remove the hinge, then

take the refrigerator door off and place it aside for the time being.

3. Remove the middle hinge, if needed.

4. Re-install the refrigerator door in reverse sequence.

When lifting up the refrigerator hinge and separating it from the door body,

please be careful not to drop the door. It could cause bodily harm or damage.

Left French Door Removal and Installation

1. First remove the top hinge cover as below.

2. Disconnect the wire cable connector and ground wire from the unit.

3. Remove the middle hinge, if needed.

4. Re-install the door in the reverse order.

When lifting the hinge as it separates from the door, be careful it doesn’t lean

forward and fall, causing you bodily harm or damaging the door.

Disconected the cable,crew out the earth line.Disconected the

water pipe on the back at the same time,pull out the pipe from

the cabinet,then take the door off.(only PBFS21* and PRFS25*)

Disconected the cable,crew out the earth line.Disconected the

water pipe on the back at the same time,pull out the pipe from

the cabinet,then take the door off.(only PBFS21* and PRFS25*)

English

8

Removing and Installing Freezer Drawer (IF REQUIRED)

1. First open the drawer as far as possible, and then remove the screw on each

side of the drawer.

2. Then pull the drawer body up and towards you, and put it aside in a safe

place.

3. Re-install the drawer in the reverse order.

Caution: Keep children and pets from playing inside the freezer drawer as a

hiding place. Use caution after drawers are removed, due to the

possibility of the plastic track protruding from unit.

English

9

connecting tHe Water suPPly line

Note: It is consumer's responsibility, if not

using a licensed plumber, to follow

your local plumbing codes.

Install the “shut off” valve on the water pipe.

1. Turn off the main water supply pipe. Turn on the

nearest tap until the water pipe is cleaned

completely.

2. Choose the position of the valve. Choose a

position for the valve that is easy to install and

reach. It is recommended to install the valve on the

side of a vertical water pipe. It is better to connect

the valve to a level water pipe on the upside of the

water pipe, not the downside, so the sediment may

flow out from the water pipe.

3. Drilling the “shut off” valve hole: Drill a 1/8”

diameter hole on the water pipe using a sharp drill.

Clean off burrs left on the water pipe by the drill.

Use caution to prevent any water flowing into

the drill.

4. Tightening the “shut off” valve: Tighten the valve

on the cold water pipe using a pipe nip. Follow

the rules specified in the 248CMR of Massachusetts

Federal Piping Standard.

Saddle-backed valves are unlawful in

Massachusetts and forbidden. Please consult a

plumber if you are unsure of the correct method to

install the valve.

5. Tightening the pipe tip: Tighten the bolts of the

pipe tip until the closing circle begins to expand.

Don’t let the bolts of the pipe tip be too tight,

otherwise the water pipe is pressed flat and

will cause a leak.

6. Positioning the water line to the refrigerator:

Position the water line between the cold water pipe

and the refrigerator. Drill a hole in the wall or on

the floor that is near the wall and the location for

the fridge. Add extra length for the water supply

line, about 8 feet (2.4 meters) and make three

circles with the diameter of each circle about 1

foot, so there is extra line to move the fridge in and

out for cleaning (unit away from the wall).

English

10

7. Connecting the water line to the “shut off” valve:

Put the tightened nut over the copper or plastic water line,

then the compression fitting, and insert the copper (or

plastic) end inside the “shut off” valve. Make sure the

pipe end sits all the way inside the valve. Tighten

(but don’t over-tighten) the nut. Follow the descriptions

specified in 248CMR of Massachusetts Federal Piping

Standard. Saddle-backed valve is unlawful in

Massachusetts and is forbidden. Please consult a

licensed plumber if you are unsure of the assembly.

8. Clear the water line supply:

Turn on the main water supply until the water in the pipe

becomes clear and clean. Turn off the water valve after

having used water for about 30 seconds – 1 minute.

9. Connect the water supply line to the refrigerator.

Note: Before connecting the water line to the refrigerator, make sure the water

line is not draped over the power cord to the refrigerator or power outlet.

(1) Tighten the water supply line at the fridge water

valve by sliding the nut over the water line end.

(2) Then, as shown in the figure, connect the end

side of the water supply line to the water valve;

tighten the water supply line nut with a crescent

wrench.

Note: Please make sure that the 1/4" water tube is fully inserted

into the water valve prior to tightening. Open the water

supply valve and check for leaks, before positioning the

unit in place.

English

11

PreParing before use

1. Remove all packaging material.

2. Check to make sure all parts and materials are available in the fridge.

Consult the seller for help if you find parts are missing.

3. Place the refrigerator in a good location (See Install Limitations on page 5).

4. Toe grille installation: Open the freezer drawer and remove the basket inside.

Install toe grille with screws from bag.

5. For the convenience of record keeping, the model and serial number,

purchase date, and receipt should be copied and taped to this manual for

safekeeping.

6. It is recommended to clean the refrigerator before use. Before putting food in

the refrigerator, please clean the inside and outside with water and diluted

baking soda. Dip clean cloth in gallon of water and spoonful of baking soda.

7. Position the fridge then plug it in. After the refrigerator is placed on a flat

surface and cleaned, turn on the power then let it run a few hours, then begin

loading it with food.

Initial Usage

1. Plug in the power cord.

2. Change the settings to the temperature desired.

3. Putting the food into the refrigerator: The refrigerator will be cooled completely

after a period of a few hours. After that, frozen and fresh foods can be put

into the refrigerator for normal use.

When changing internal temperatures, a new balance temperature will occur

after a period of time. The length of this period of time depends on the degree of

the temperature change, the ambient temperature, the frequency of door

openings, and the amount of stored food in the fridge.

English

12

setting tHe control functions

(1) The Top Refrigerator Control Center

E. Quick-freeze Button

F. Freezer Temperature

Adjusting Button

G. Freezer Temperature

Adjusting Button

H. Freezer Temperature

Indicating Area

I. Refrigerator Temperature

Indicating Area

J. Refrigerator Temperature

Adjusting Button

K. Refrigerator Temperature

Adjusting Button

L. Refrigerator Quick-chill Button

M. Water Filter Reset and Energy

Saver Button

N. Water Filter Indicator Light

ENERGY SAVER

E F G H I J K L M N

English

13

(2) Fresh Food temperature adjustment

Press Button J or Button K: The fresh food temperature control center will flash.

When the temperature is set, the temperature range is 34 to 44 degrees F. Each

time you press Button K, temperature will increase a level, until the highest

temperature level is reached. Each time you press J, the temperature will

decrease a level, until the lowest temperature level is reached.

(3) Freezer temperature adjustment

Press Button F or Button G on the freezer temperature control center: Area H will

flicker. When the temperature is set, the range of the freezer is -6 to 6 degrees F.

Each time you press Button G, the freezer temperature will increase a level, until

the highest temperature level is reached; each time you press Button F, the freezer

temperature will decrease a level, until the lowest temperature level is reached.

setting tHe control functions (cont'D)

I J K

ENERGY SAVER

F G H

ENERGY SAVER

English

14

(4) Freezer Express-freeze setting

The function of Express-freeze is to freeze the food completely in the shortest time.

Press Button E: The Express-freeze button indicator will light and the freezer will

be in the Express-freeze mode. It will remain in this mode for 3 hours. You can

press Button E before 3 hours is up if you wish to end the Express-freeze mode

early.

(5) Fresh Food Express-chill setting

Press Button L: The Fresh Food Express-chill refrigerator button indicator lamp

will light and the refrigerator will be in the Express–chill refrigerator mode. The

refrigerator will stop Express–chill mode if the storage temperature is 2° F lower

than its desired temperature or after 3 hours pass. If you want the refrigerator

to exit Express-chill mode, press Button L again. The Express-chill button indicator

will go out, and the refrigerator will exit Express-chill.

Caution! When the refrigerator is in the Express-freeze or Express-chill modes,

within the set time, the process of refrigerating remains constant.

setting tHe control functions (cont'D)

E

ENERGY SAVER

L

ENERGY SAVER

English

15

(6) Quick–ice function

Press Button E and M at the same time for three seconds: The indicator light

button N of the water filter will flash, and the freezer will be in the Quick–ice

mode; 24 hours later it will exit the quick-ice mode automatically. Press Button E

and M at the same time for three seconds again to exit the Quick–ice mode.

(7) Stopping icemaker function

Press Button G and J at the same time for three seconds: The indicator lamp E will

flash, and icemaker will turn off. When you press Button G and J at the same

time for three seconds again, the icemaker will turn on again.

(8) Sabbath function

Press Button E and L at the same time for 3 seconds: The Sabbath function will

be in effect after the first sound of the buzzer. If there is no buzzer sound, the

LED screen light will go out, and all the lamps and chimes, as well as the water

dispenser, will not function. Press Button E and L at the same time for 3 seconds

again, and the Sabbath function will turn off after the buzzer sounds. The LED

screen light will now be in effect.

(9) Celsius/Fahrenheit conversion function

Press Button F, G, and J on the control center at the same time for 3 seconds:

Celsius Temperature Readings will be in effect after the first sound of the buzzer.

Press Button F, G, and J on the control center at the same time for 3 seconds

again to switch to Fahrenheit mode. Fahrenheit mode will be in effect after the

first sound of the buzzer.

setting tHe control functions (cont'D)

ENERGY SAVER

E M N

E G J

ENERGY SAVER

E L

ENERGY SAVER

F G J

ENERGY SAVER

English

16

(10) The water filter indicator setting

When the indicator light of the water filter is lit up, the water filter should be

changed. After the water filter is changed, press and hold the water filter reset

button M for one second. The indicator light of the water filter N will go out.

Caution! When the water filter needs to be changed, please refer to the “water

filter” section.

MUST FLUSH 3.75 GALLONS THROUGH FILTER BEFORE USE

(approximately 5 minutes.)

Note: Our water filters comply with CA. propositions requirements.

(11) Energy Saver

1. The energy saver button is initially set to ON. You can see "ES" on the right

display for 3 seconds if you open the refrigeration doors, then it will turn back

to show the refrigeration temperature.

2. By pressing and holding the "energy saver" button M on the control panel for

5 seconds, you can turn on or off the Energy Saver feature.

3. "ES" will appear only when the Energy Saver in the ON position.

Note: See additional information on page 3.

setting tHe control functions (cont'D)

ENERGY SAVER

M N

ENERGY SAVER

M

English

17

(13) Door ajar alarm

When any door is open for over :60 seconds, the door ajar alarm function of the

refrigerator will go off, and the refrigerator will produce buzzers once every :30

seconds. This alerts the user that there is a door left open.

(14) Over-voltage protection

The refrigerator is equipped for over-voltage protection. When the function of

over-voltage is in effect, the refrigerator will turn off automatically. After 5

minutes, the power should be turned back on.

(15) Power-break memorization function

When the refrigerator cuts off from over-voltage protection, the settings of the

refrigerator before the power break are memorized. This allows the refrigerator

to return to the previous settings when it is turned back on.

(16) Fault Display

If the display is broken but you still hear accompanying beeps when you press

buttons, this means the buttons are still working. However, you should call an

after-sales service engineer to fix the problem to ensure optimum performance.

F G K

ENERGY SAVER

(12) Demo mode

1. Compressor and fan motors do not operate in the demo mode.

2. Press Button F, G, and K at the same time for 3 seconds: After the first sound

of the buzzer, the demo mode will be in effect. Press Button F, G, and K at the

same time for 3 seconds again, and the demo mode will be canceled.

setting tHe control functions (cont'D)

English

18

• Short term fresh or frozen food can be placed in the upper fresh food section

or in the ice cream drawer. Keep raw foods near the lower area, away from

ready to eat food in the top area.

• The height of the cantilever shelves can be adjusted to fit your storage needs.

When adjusting the height of the shelf, first remove any foods placed on the

shelf. Then lift up by tilting the front up and pull it up. This will unlatch the rear

hooks. Then place the hooks in a new ladder slot location and tilt back down

into position on an even, horizontal plane.

Caution! Make sure that the two sides of the shelf are in balance, otherwise, the

shelf may fall down or the food may slide.

• Crisper use

The refrigerator is designed to include a fruits, vegetables, and/or deli crisper.

The inside temperature can be adjusted according to the type of food being

stored.

• Turn up the humidity control button on the right side of the crisper, for a high

humidity, to store cucumbers, grapes, oranges, apples, peaches, lettuce, and

other produce that’s high in moisture.

• Turn down the humidity control button on the right side of the crisper to lower

the humidity. This is suitable for storing meats, cheeses, onions, tomatoes and

other drier foods.

• Full-width pantry and its usage

The refrigerator is specially designed to include a full-width pantry. The inside

temperature can be adjusted, depending on the type of food to be stored there.

Note: To avoid damage do not press the air-adjusting button too hard.

Door bin height adjustment and cleaning

To change location, lift up the door bin while holding it by its two sides, and pull

it straight out. After being cleaned, the door bin can be installed in the reverse

manner, and the position can be adjusted according to the height of the food to

be stored.

Crisper cover removal

Lift up the shelf, then pull it straight out in the direction shown.

Caution! When adjusting the height of the door bin, it is better to keep the

dairy bin above the door bin.

fooD storage tiPs

English

19

• It is recommended to keep some space between foods for good cold air

circulation. The temperatures in the refrigerator are slightly warmer near the

top and colder near the base.

• Changing the Fresh Food Light Bulbs

The voltage and wattage of the fresh food bulbs are: 115volt, 60 Hz – 40W.

(Never use bulbs with power over 40W.)

When changing the light bulbs:

• Pull out the power cord plug from the wall outlet, cutting off the power.

1. Use your hands to press down at the back of the light-shield, releasing

two tabs.

2. Hold the light-shield and pull it out.

• Turn the bulb in a counterclockwise direction, and put in a new bulb by turning

it clockwise.

• Re-install the light-shield back in the tabs in the reverse order, and snap back in

place.

• Removing and installing air curtain (only for servicing if needed).

1. Remove the water filter.

2. Take off the fresh food light-shield, and unscrew the bulb.

3. Remove the screws of the air curtain frame, using a screwdriver.

4. Take down the fresh food air curtain, using your hands to press down

on the air curtain with a little bit of pressure.

• Re-install the air curtain by following these steps in the reverse order.

fooD storage tiPs (cont'D)

La page charge ...

Haier H21BFC45NS Manuel utilisateur

Ce manuel convient également à

Haier H21BFC45NS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents