Panasonic PVGS65 Mode d'emploi

Catégorie
Caméscopes
Taper
Mode d'emploi
Spanish Quick Use Guide is included.
Guía para rápida consulta en español está incluida.
LSQT0860 A
For USA assistance, please call: 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
For Canadian assistance, please call: 1-800-561-5505 or visit us at www.panasonic.ca
Digital Video Camcorder
Operating Instructions
Model No. PV-GS65
Mini
Before connecting, operating or adjusting this product,
please read the instructions completely.
LSQT0860ENG.book 1 ページ 2004年12月22日 水曜日 午後2時38分
2
LSQT0860
Things You Should Know
Thank you for choosing Panasonic!
You have purchased one of the most
sophisticated and reliable products on the
market today. Used properly, we’re sure it will
bring you and your family years of enjoyment.
Please take time to fill in the information on the
right.
The serial number is on the tag located on the
underside of your Camcorder. Be sure to retain
this manual as your convenient Camcorder
information source.
Safety Precautions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
Your
Camcorder is designed to record and play back in Standard Play (SP) mode and Long Play
(LP) mode
It is recommended that only cassette tapes that have been tested and inspected for use in Camcorder
with the
mark be used.
AC Adaptor
The rating plate is on the underside of the AC Adaptor.
Ò
Ò
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user
that uninsulated voltage within
the unit may have sufficient
magnitude to cause electric
shock.
Therefore, it is dangerous to
make any kind of contact with
any inside part of this unit.
This symbol alerts the user that
important literature concerning
the operation and maintenance
of this unit has been included.
Therefore, it should be read
carefully in order to avoid any
problems.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
LSQT0860ENG.book 2 ページ 2004年12月22日 水曜日 午後2時38分
3
LSQT0860
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, follow the attached installation instructions and use
only shielded interface cables with ferrite core when connecting to computer or peripheral devices.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
CAUTION: TO PREVENT FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT TYPE.
Since this product gets hot during use, operate it in a well ventilated place; do not install this
equipment in a confined space such as a bookcase or similar unit.
AS WITH ANY SMALL OBJECT, SD CARDS CAN BE SWALLOWED BY YOUNG CHILDREN. DO
NOT ALLOW CHILDREN TO HANDLE THE SD CARD.
Declaration of Conformity
Trade Name: Panasonic
Model No.: PV-GS65
Responsible party: Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact: Panasonic Consumer Electronics Company
1-800-211-PANA (7262)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1)This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
WARNING
LSQT0860ENG.book 3 ページ 2004年12月22日 水曜日 午後2時38分
4
LSQT0860
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or the table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when it will be left unused for
long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
S3125A
LSQT0860ENG.book 4 ページ 2004年12月22日 水曜日 午後2時38分
5
LSQT0860
Precautions
USE & LOCATION
TO AVOID SHOCK HAZARD ... Your
Camcorder and power supply should not be
exposed to rain or moisture. Do not connect the
power supply or operate your Camcorder if it
gets wet. Your Camcorder has been designed
for outdoor use, however it is not designed to
sustain direct exposure to water, rain, sleet,
snow, sand, dust, or a direct splashing from a
pool or even a cup of coffee. This action could
permanently damage the internal parts of your
Camcorder. Do not attempt to disassemble this
unit. There are no user serviceable parts inside.
Unplug your Camcorder from the power supply
before cleaning.
DO NOT AIM YOUR CAMCORDER AT THE
SUN OR OTHER BRIGHT OBJECTS
DO NOT LEAVE THE CAMCORDER WITH
THE EVF AIMED DIRECTLY AT THE SUN AS
THIS MAY CAUSE DAMAGE TO THE
INTERNAL PARTS OF THE EVF
DO NOT EXPOSE YOUR CAMCORDER TO
EXTENDED HIGH TEMPERATURE ... Such as,
in direct sunlight, inside a closed car, next to a
heater, etc... This action could permanently
damage the internal parts of your Camcorder.
AVOID SUDDEN CHANGES IN
TEMPERATURE ... If the unit is suddenly
moved from a cold place to a warm place,
moisture may form on the tape and inside the
unit.
DO NOT LEAVE YOUR CAMCORDER OR
THE POWER SUPPLY TURNED ON WHEN
NOT IN USE.
STORAGE OF YOUR CAMCORDER ... Store
and handle your Camcorder in a manner that
will not subject it to unnecessary movement
(avoid shaking and striking). Your Camcorder
contains a sensitive pick-up device which could
be damaged by improper handling or storage.
CARE
TO CLEAN YOUR CAMCORDER ... Do not use
strong or abrasive detergents when cleaning
your Camcorder body.
TO PROTECT THE LENS ... Do not touch the
surface of the lens with your hand. Use a
commercial Camcorder lens solution and lens
paper when cleaning the lens. Improper
cleaning can scratch the lens coating.
TO PROTECT THE FINISH OF YOUR
CAMCORDER ... Before handling your
Camcorder, make sure your hands and face are
free from any chemical products, such as
suntan lotion, as it may damage the finish.
Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, and 4,819,098, licensed for limited
viewing.
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation,
and is intended for home and other limited viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is prohibited.
WARNING
CAUTION
This class B digital apparatus complies with CANADIAN ICES-003.
A lithium ion/polymer battery that is recyclable powers the product
you have purchased. Please call 1-800-8-BATTERY for information
on how to recycle this battery.
U.S.A./CANADA CONSUMERS: ATTENTION:
LSQT0860ENG.book 5 ページ 2004年12月22日 水曜日 午後2時38分
6
LSQT0860
Contents
Before using
Quick Guide..................................................... 8
Accessories ................................................... 10
Parts identification and handling.................... 10
Fitting the lens cap......................................... 12
The one-touch free-style grip belt .................. 12
Using the LCD monitor .................................. 13
Using the viewfinder ...................................... 13
Power supply ................................................. 14
Charging time and recordable time................ 15
Inserting/removing a cassette........................ 15
Inserting/removing a card .............................. 16
Turning the Camcorder on............................. 17
Selecting a mode ........................................... 17
How to use the joystick.................................. 18
Switching the language.................................. 19
Using the menu screen.................................. 19
Setting date and time..................................... 20
Adjusting LCD monitor/viewfinder.................. 21
Using the remote control................................ 22
Record mode
Check before recording ................................. 24
Recording on a tape ...................................... 25
Recording still pictures on a card while
recording image onto a tape ....................... 26
Check the recording ...................................... 26
Blank search function .................................... 26
Recording still pictures onto a card
(Photoshot) ................................................. 26
Zoom in/out function...................................... 27
Recording yourself ........................................ 28
Quick start ..................................................... 29
Backlight compensation function................... 29
MagicPix functions ........................................ 30
Soft skin mode............................................... 30
Tele-macro function....................................... 31
Fade in/fade out function ............................... 31
Wind noise reduction function ....................... 31
Self-timer recording ....................................... 32
Recording images for wide-screen TVs ........ 32
Image stabilizer function................................ 32
RapidFire Consecutive Photoshot ................. 33
Recording in various situations
(Scene mode) ............................................. 33
Recording in natural colors
(White balance)........................................... 34
Manual focus adjustment .............................. 35
Manual shutter speed/aperture
adjustment .................................................. 36
LSQT0860ENG.book 6 ページ 2004年12月22日 水曜日 午後2時38分
7
LSQT0860
Playback mode
Playing back tape .......................................... 37
Slow-motion playback/
frame-by-frame playback ............................ 37
Variable-speed search function ..................... 38
Playback on TV.............................................. 39
Playing back card .......................................... 39
Deleting files recorded on a card ................... 40
Formatting a card........................................... 41
Protecting files on a card ............................... 41
Writing the printing data on a card
(DPOF setting) ............................................ 41
Edit mode
Recording from a tape onto a card ................ 42
Copying onto a DVD recorder or a VCR
(Dubbing) .................................................... 42
Using the DV cable for Recording
(Digital Dubbing) ........................................ 43
Audio dubbing................................................ 44
Printing pictures by directly connecting to the
printer (PictBridge) ...................................... 45
Connecting Computer and Camcorder .......... 46
Installing the USB Driver................................ 46
To disconnect USB Cable safely ................... 47
Menu
Menu list ........................................................ 49
Menus related to taking pictures ................... 51
Menus related to playback ............................ 51
Other menus.................................................. 52
Others
Indications ..................................................... 53
Warning/alarm indications ............................. 54
Functions cannot be used simultaneously .... 55
Before requesting repair
(Problems and solutions) ............................ 56
Cautions for Use............................................ 59
Explanation of terms...................................... 63
Specifications ................................................ 65
Camcorder Accessory System ...................... 67
Camcorder Accessory Order Form
(For USA Customers) ................................. 68
Request for Service Notice (USA Only) ........ 69
Limited Warranty (For USA Customers)........ 70
Customer Services Directory......................... 71
Warranty (For Canadian Customers) ............ 72
Index.............................................................. 73
Spanish Quick Use Guide/
Guía española para el uso rápido............... 74
LSQT0860ENG.book 7 ページ 2004年12月22日 水曜日 午後2時38分
Before using
8
LSQT0860
Quick Guide
ª Charging the battery
1 Connect the AC main lead to the AC adaptor
and the AC main socket.
2 Put the battery on the battery mount by
aligning the mark, and then securely plug it
in.
ª
Fitting the battery
Push the battery against the battery holder and
slide it until it clicks.
ª
Inserting/removing a cassette
1 Slide the [OPEN/EJECT] lever and open the
cassette cover.
2 After the cassette holder is opened, insert/
remove the cassette.
3 Push the [PUSH] mark 1 in order to close
the cassette holder.
4 Only after the cassette holder is completely
housed, close the cassette cover.
ª
Inserting/removing a card
1 Open the LCD monitor and then open the
card slot cover.
2 Insert/remove the card into/from the card
slot.
When inserting a card, face the label side 1
towards you and push it straight in with one
stroke as far as it goes.
When removing the card, open the card slot
cover and press the center of the card and
then pull it straight out.
3 Securely close the card slot cover.
ª
How to turn on the power
1
While pressing the button 1, set the [OFF/
ON] switch to [ON].
OPEN/
EJECT
PUSH
1
1
OFF ON
1
LSQT0860ENG.book 8 ページ 2004年12月22日 水曜日 午後2時38分
Before using
9
LSQT0860
ª How to turn off the power
1 While pressing the button 1, set the [OFF/
ON] switch to [OFF].
ª
Recording on a tape
Set to Tape Recording Mode.
1 Press the recording start/stop button to
start recording.
2 Press the recording start/stop button again
to pause recording.
ª
Recording still pictures onto a card
(Photoshot)
Set to Card Recording Mode.
1 Press the [PHOTO SHOT] button.
ª
Playing back tape
Set to Tape Playback Mode.
1 Operate with joystick.
1/;: Playback/Pause
6: Rewind/Review playback (Reverts to
playback with the 1/; icon.)
5: Fast forward/Cue playback (Reverts to
playback with the 1/; icon.)
:Stop
ª
Playing back card
Set to Picture Playback Mode.
1 Operate with joystick.
E: Plays back the previous picture.
D: Plays back the next picture.
1/: Slide show (Plays back the still pictures
on the card in order) start/stop
OFF ON
1
PC
;
PC
PHOTO
SHOT
PC
PC
LSQT0860ENG.book 9 ページ 2004年12月22日 水曜日 午後2時38分
Before using
10
LSQT0860
Before using
Accessories
The following are the accessories supplied with
this product.
1) AC adaptor, DC cable, AC cable
-14-
2) Battery pack -14-
3) Remote control, button-type battery -22-
4) Lens cap -12-
5) AV cable -42-
6) Shoulder strap -12-
7) USB cable -45-
Parts identification and handling
ª Camcorder
(1) Recording lamp -51-
(2)
Microphone (built-in, stereo) -28-, -31-
(3)
Grip belt
(One-touch free style grip belt)
-12-
(4)
Lens
(5) White balance sensor -35-
Remote control sensor -23-
(6)
Lock button -12-
(7)
Lock cover -12-
(8)
Audio-video output terminal [AV] -42-
Use the supplied AV cable or headphones
only, otherwise audio may not be played
back normally.
Headphone terminal [Ë]
(9) Microphone terminal [MIC]
A compatible plug-in powered microphone
can be used as an external microphone.
When the Camcorder is connected with AC
Adaptor, sometimes noise may be heard
depending on microphone type. In that
case, please switch to battery for power
supply and noise will stop.
(10) USB terminal [ ] -45-
(11)
Speaker -37-
CAUTION:
This unit will operate on 110/120/220/240 V
AC. An AC plug adaptor may be required for
voltages other than 120 V AC. Please
contact either a local or foreign electrical
parts distributor for assistance in selecting
an alternate AC plug. We recommend using
the accessory power plug adaptor
(VJSS0070) in an area which has special AC
outlets.
PV-DAC14D
CGR-DU06
K2GJ2DZ00017
1)
2)
K2KC4CB00018
5)
6)
VFC3506-1A
CR2025
N2QAEC000012
3)
VYF3031
4)
K2CA2CA00025
K2KZ4CB00006
7)
(1)
(2)
(4)
(5)
(6)
(7)
(3)
AV/
MIC
(8)
(9)
(10)
(11)
LSQT0860ENG.book 10 ページ 2004年12月22日 水曜日 午後2時38分
Before using
11
LSQT0860
(12) Viewfinder -13-, -63-
(13)
Battery holder
(14) Battery eject button [PUSH BATT] -14-
(15)
Power switch [OFF/ON] -17-
(16)
Power lamp -17-
(17)
Quick start recording button
[QUICK START]
-29-
Quick start recording lamp -29-
(18)
Menu button [MENU] -19-
(19)
Joystick -18-
(20)
Mode dial -17-
(21)
Recording start/stop button -25-
(22)
S-Video output terminal [S-VIDEO] -39-
(23)
LCD monitor -13-, -63-
(24) LCD monitor open knob [OPEN4] -13-
(25)
Reset button [RESET] -54-
(26)
Power LCD button [POWER LCD] -21-
Power LCD lamp -21-
(27)
Mode select switch [AUTO/MANUAL/
FOCUS]
-24-, -33-, -36-
(28)
Card access lamp -17-
(29)
DV terminal [DV] -43-
(30)
Card slot cover -16-
(31)
Card slot -16-
(32)
Cassette holder -15-
(33)
Cassette eject lever [OPEN/EJECT] -15-
(34)
Cassette cover -15-
(35)
Zoom lever [W/T] -27-
Volume lever [s /VOLr] -37-
(36)
Photoshot button [PHOTO SHOT] -26-
(37)
Accessory shoe
Accessories, such as a stereo microphone, are
attached here.
(38) Tripod receptacle
This is a hole for attaching the Camcorder to
optional tripod. (Please carefully read the
operating instructions for how to attach the tripod
to the Camcorder.)
You cannot open the card slot cover when the
tripod is used. Insert the card first and then
attach the tripod.
Due to limitations in LCD production
technology, there may be some tiny bright or
dark spots on the viewfinder screen.
However, this is not a malfunction and does
not affect the recorded picture.
Due to limitations in LCD production
technology, there may be some tiny bright or
dark spots on the LCD monitor screen.
However, this is not a malfunction and does
not affect the recorded picture.
S-VIDEO
(12)
(13)
(14)
(15)
(16)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(29)
(30)
(31)
(32)
(33)
(34)
(35)
(36)
(37)
(38)
LSQT0860ENG.book 11 ページ 2004年12月22日 水曜日 午後2時38分
Before using
12
LSQT0860
(39) Shoulder strap fixture
Put the strap through the fixture 1 and through
the stopper 2 so it will not come off. Extend
part 3 by at least 1 inch (2 cm).
Fit the other end of the belt similarly.
(40) Lens hood
In order to remove the lens hood, rotate it
counter-clockwise 1. In order to fit it, put into slot
2, and then rotate it clockwise.
Fitting the lens cap
Fit the lens cap to protect the surface of the lens.
1 Remove the grip belt. Run the end of the
lens cap cord through the hole in the grip
belt attachment and run the lens cap
through the lens cap cord.
The lens cap removed can be attached to the
lens cap fixture. (It cannot be hung if the grip
belt is used as a hand strap.)
To fit or remove the lens cap, hold both sides of
the lens cap with the tips of your finger and
thumb.
The one-touch free-style grip belt
ª To use as a hand strap
If you use the grip belt as a hand strap, then you
can carry or handle this Camcorder more easily.
1 Open the lock cover 1 by pinching the
projections 2 on both sides. Press the lock
button 3 to remove the grip belt.
When removing the grip belt, tightly hold the
Camcorder with both hands.
After removing the grip belt, restore the lock
cover to the original position.
2 Adjust the belt length.
1 Flip the belt.
2 Slide 1 in the direction indicated by the arrow.
3 Fix the belt.
3 Put your hand through the strap.
Hold the Camcorder not to cover the
microphones or the sensors with your hands.
(39)
3
2
1
1
2
(40)
2
1
3
1
3
1
2
LSQT0860ENG.book 12 ページ 2004年12月22日 水曜日 午後2時38分
Before using
13
LSQT0860
ª To restore the strap to the grip belt
When returning the grip belt to the grip belt
attachment, press the lock cover 1 and check if
the grip belt is securely locked.
ª
To use as a grip belt
Adjust the belt length so it fits your hand.
1 Adjust the belt length and the pad position.
1 Flip the belt.
2 Adjust the length.
3 Fix the belt.
Using the LCD monitor
You can record the image while viewing it on the
LCD monitor.
1 Put a finger on the [OPEN4] knob and pull
the LCD monitor out in the direction of the
arrow.
The viewfinder is now deactivated.
It can open up to 90o.
2 Adjust the angle of the LCD monitor
according to your preference.
It can rotate up to 180o 1 towards the lens or
90o 2 towards the viewfinder.
The brightness and color level of the LCD
monitor can be adjusted from the menu.
If it is forcibly opened or rotated, the Camcorder
may be damaged or fail.
Check that the card slot cover is closed.
When the LCD monitor is rotated by 180o
towards the lens (when recording yourself), the
LCD monitor and the viewfinder will be
simultaneously activated.
Using the viewfinder
ª Extending the viewfinder
1 Pull out the viewfinder and extend it by
pulling the extension knob.
ª Adjusting the field of view
1 Adjust the focus by sliding the eyepiece
corrector knob.
You can adjust the brightness of the viewfinder
from the menu.
1
1
3
2
1 180o 2 90o
12:30:45PM
OCT 15 2005
12:30:45PM
OCT 15 2005
12:30:45PM
OCT 15 2005
12:30:45PM
OCT 15 2005
LSQT0860ENG.book 13 ページ 2004年12月22日 水曜日 午後2時38分
Before using
14
LSQT0860
Power supply
ª Charging the battery
When this product is purchased, the battery is not
charged. Charge the battery before using this
product.
Battery charging time (
-15-)
We recommend using Panasonic batteries.
If you use other batteries, we cannot guarantee
the quality of this product.
If the DC input lead is connected to the AC
adaptor, then the battery will not charge.
Remove the DC input lead from the AC adaptor.
1 Connect the AC cable to the AC adaptor and
the AC jack.
2 Put the battery on the battery mount by
aligning the mark, and then securely plug it
in.
ª
Charging lamp
Lights up: Charging
Goes off: Charging completed
Flashing: The battery is over discharged
(discharged excessively). In a while,
the lamp will light up and normal
charging will start.
When the battery temperature is
excessively high or low, the [CHARGE]
lamp flashes and the charging time will
be longer than normal.
ª
Connecting to the AC outlet
1
Connect the AC cable to the AC adaptor and
the AC jack.
2 Connect the DC cable to the AC adaptor.
3 Connect the DC cable to this product.
The output plug of the AC cable is not
completely connected to the AC adaptor jack.
As shown in 1, there is a gap.
Do not use the power cord for other
equipment since the power cord is exclusively
designed for this Camcorder. Do not use the
power cord from other equipment for this
Camcorder.
ª
Fitting the battery
Push the battery against the battery holder and
slide it until it clicks.
ª
Removing the battery
While pushing the [PUSH BATT] button, slide the
battery (or the DC input lead) to remove it.
Hold the battery with your hand so it does not
fall.
1
PUSH
BATT
LSQT0860ENG.book 14 ページ 2004年12月22日 水曜日 午後2時38分
Before using
15
LSQT0860
Charging time and recordable time
The times shown in the table below show the
times at a temperature of 68oF (25oC) and a
humidity of 60%. This is just a guide. If the
temperature is higher or lower than the specified
value, the charging time will become longer.
A Charging time
B Maximum continuously recordable time
“1h. 10 min.” indicates 1 hour 10 minutes.
The battery CGR-DU06 is supplied.
The times shown in the table are rough
estimates. The times indicate the recordable
time when the viewfinder is used. The times in
parentheses indicate the recordable time when
the LCD monitor is used.
We recommend the Battery Pack CGA-DU12
and CGA-DU21 for long recording time (2 hour
or more for continuous recording, 1 hour or
more for intermittent recording).
The recordable time will become shorter in the
following cases:
When you use both the viewfinder and the
LCD monitor simultaneously while rotating
the LCD monitor frontward to record yourself,
0 Lux MagicPix function, etc.
When you use this Camcorder with the LCD
monitor lit up by pressing the [POWER LCD]
button.
The batteries heat up after use or charging. The
Camcorder being used will also heat up. This is
normal.
Along with the reduction of the battery capacity,
the display will change: r # s #
t # u # v. If the battery
discharges, then u (v) will flash.
Inserting/removing a cassette
1 Slide the [OPEN/EJECT] lever and open the
cassette cover.
When the cover is fully opened, the cassette
holder will come out.
2 After the cassette holder is opened, insert/
remove the cassette.
When inserting a cassette, orient it as shown
in the figure, and then securely insert it as far
as it goes.
When removing, pull it straight out.
3 Push the [PUSH] mark 1 in order to close
the cassette holder.
4 Only after the cassette holder is completely
housed, close the cassette cover.
After using, make sure to rewind the cassette
completely, remove it, and put it in a case. Store
the case in an upright position. (
-62-)
When condensation is formed on the lens or the
main unit of the Camcorder, even if no
condensation alarm is indicated, condensation
may have formed on the heads or the cassette
tape. Do not open the cassette cover. (
-59-)
ª
When the cassette holder does not
come out
Close the cassette cover completely, and then
open it again completely.
Check if the battery has run down.
ª
When the cassette holder cannot be
housed
Set the [OFF/ON] switch to [OFF], then to [ON]
again.
Check if the battery has run down.
Supplied
battery/
CGR-DU06
(7.2 V/
640 mAh)
A 1 h. 40 min.
B 1 h. 25 min.
(1 h. 20 min.)
CGA-DU12
(7.2 V/
1150 mAh)
A 2 h. 25 min.
B 2 h. 40 min.
(2 h. 25 min.)
CGA-DU21
(7.2 V/
2040 mAh)
A 3 h. 55 min.
B 4 h. 30 min.
(4 h. 15 min.)
OPEN/
EJECT
PUSH
1
LSQT0860ENG.book 15 ページ 2004年12月22日 水曜日 午後2時38分
Before using
16
LSQT0860
ª Inserting/removing the cassette
When the cassette holder is in motion, do not
touch anything except the [PUSH] mark.
When inserting a previously recorded cassette,
use the blank search function to find the position
where you want to continue recording. If you
overwrite-record on a previously recorded
cassette, be sure to find the position where you
want to continue recording.
Close the cassette cover tightly.
When closing the cassette cover, do not get
anything, such as a cable, caught in the cover.
ª
Accidental erasure prevention
If the accidental erasure prevention slider 1 of a
cassette is opened (slide in the direction of the
[SAVE] arrow), the cassette cannot be recorded.
When recording, close the accidental erasure
prevention slider of the cassette (slide in the
direction of the [REC] arrow).
Inserting/removing a card
Before inserting/removing a card, be sure to turn
the power [OFF].
If the card is inserted or removed with the power
turned on, this Camcorder may malfunction or
the data recorded on the card may be lost.
1 Open the LCD monitor and then open the
card slot cover.
2 Insert/remove the card into/from the card
slot.
When inserting a card, face the label side 1
towards you and push it straight in with one
stroke as far as it goes.
When removing the card, open the card slot
cover and press the center of the card and
then pull it straight out.
3 Securely close the card slot cover.
ª
Concerning the card
Do not touch the terminals on the back of the
card.
Do not format the card with another Camcorder
or any personal computer. This operation may
make the card unusable.
Electrical noise, static electricity, or failure of the
Camcorder or the card may damage or erase
the data stored on the card. We recommend
saving important data on a personal computer
by using a USB cable, PC card adaptor, or USB
reader/writer.
R E C
SAVE
1
1
LSQT0860ENG.book 16 ページ 2004年12月22日 水曜日 午後2時38分
Before using
17
LSQT0860
ª Card access lamp
When the Camcorder accesses the card
(reading, recording, playback, erasing, etc.), the
access lamp lights up.
If the following operations are performed when
the access lamp is lit, then the card or the
recorded data may be damaged or the
Camcorder may malfunction.
Opening the card slot cover and inserting or
removing the card
Operating the [OFF/ON] switch or the mode
dial
ª
SD Memory Card
The memory capacity indicated on the SD
Memory Card label corresponds to the total
amount of capacity to protect and manage the
copyright and the capacity available as
conventional memory for a Camcorder,
personal computer or other equipment.
ª
Concerning the write protection
switch on the SD Memory Card
The SD Memory Card has a write protection
switch on it. If the switch is moved to [LOCK],
you cannot write to the card, erase the data on
it, or format it. If it is moved back, you can
perform those functions.
Turning the Camcorder on
When the Camcorder is turned on with the lens
cap fitted, the automatic white balance
adjustment may not function properly. Please turn
the Camcorder on after removing the lens cap.
ª
How to turn on the power
1
While pressing the button 1, set the [OFF/
ON] switch to [ON].
The power lamp lights up.
ª How to turn off the power
1 While pressing the button 1, set the [OFF/
ON] switch to [OFF].
The power lamp goes off.
Selecting a mode
Rotate the mode dial to select the desired mode.
1 Rotate the mode dial.
Set your desired mode to 1.
: Tape recording mode
Use this when you want to record the image on a
tape. (Also, you can simultaneously record still
pictures on a card while recording images on a
tape.)
: Tape playback mode
Use this to play back a tape.
: Card recording mode
Use this to record still pictures on a card.
: Picture playback mode
Use this to play back the still pictures recorded on
a card.
:PC mode
You can view or edit the images recorded on a
card on your personal computer.
OFF ON
1
OFF ON
1
PC
1
Joystick
PC
LSQT0860ENG.book 17 ページ 2004年12月22日 水曜日 午後2時38分
Before using
18
LSQT0860
How to use the joystick
ª Basic joystick operations
Operations on the menu screen and selection
of files to be played back on the multi-image
display
Move the joystick up, down, left, or right to select
an item or file, and then push in the center to set
it.
ª
Joystick and screen display
Push the center of the joystick, and icons will be
displayed on the screen. Each push switches the
display as follows depending on the mode.
(In the Tape playback mode or the Picture
playback mode, the icons will be automatically
displayed on the screen.)
1) Tape recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[AUTO])
2) Tape recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[MANUAL])
3) Tape playback mode
4) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[AUTO])
1 Select by moving up.
2 Select by moving down.
3 Select by moving left.
4 Select by moving right.
5 Push the center to select the item.
3 Tele-macro
-31-
4 Soft skin mode -30-
2 Fade -31-
1 Backlight compensation -29-
3 MagicPix/0 Lux MagicPix -30-
4 Recording check -26-
1
3
2
4
5
Screen
display OFF
4 White balance
Shutter speed
Iris or gain value
-34-
1 Select/Adjust -34-
2 Select/Adjust -34-
3 Playback/pause -37-
4 Stop -37-
2 Rewind (review playback) -37-
1 Fast forward (cue playback) -37-
3 Tele-macro -31-
4 Soft skin mode -30-
1 Backlight compensation -29-
Screen display
OFF
Screen
display OFF
Screen
display OFF
LSQT0860ENG.book 18 ページ 2004年12月22日 水曜日 午後2時38分
Before using
19
LSQT0860
5) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to
[MANUAL])
6) Picture playback mode
Switching the language
You can switch the language on the screen
display or the menu screen.
1 Set [LANGUAGE] >> [English].
Using the menu screen
For each individual menu, please refer to -49-.
1 Press the [MENU] button.
The menu corresponding to the mode
selected by the mode dial is displayed.
Do not switch the mode dial when the menu is
displayed.
2 Move the joystick up or down in order to
select the top menu.
3 Move the joystick right or press it to set the
selection.
4 Move the joystick up or down in order to
select the sub-menu.
5 Move the joystick right or press it to set the
selection.
4 White balance
Shutter speed
Iris or gain value
-34-
1 Select/Adjust -34-
2 Select/Adjust -34-
3 Playback/stop -39-
4 Erase -40-
2 Playback previous picture -39-
1 Playback next picture -39-
Screen
display OFF
Screen
display OFF
MENU
LSQT0860ENG.book 19 ページ 2004年12月22日 水曜日 午後2時38分
Before using
20
LSQT0860
6 Move the joystick up or down in order to
select the item to be set.
7 Press the joystick to determine the setting.
ª
To exit the menu screen
Press the [MENU] button.
ª
To get back to the previous screen
Move the joystick left.
ª
About the menu setting
The menu screen does not appear during
recording. And you cannot record when the
menu screen appears.
ª
Operating with remote control
The menu screen transition is the same as when
the buttons on the main unit are used.
1 Press the [MENU] button.
2 Select a menu item.
Use the direction buttons (π, , , ) and
[ENTER] button in place of the joystick on the
main unit.
3 Press the [MENU] button, to exit the menu
screen.
Setting date and time
If the screen shows the incorrect date/time, then
adjust it.
Set to Tape Recording Mode or Card
Recording Mode.
1 Set [BASIC] >> [CLOCK SET] >> [YES].
2 Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
The 12-hour clock is used.
3 Press the joystick to determine the setting.
The clock function starts at [00] seconds.
ª
About date/time
The date and time function are driven by a
built-in lithium battery.
Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
If [0] or [--] is indicated when the Camcorder is
turned on, then the built-in lithium battery has
run down. Connect the AC adaptor to the
Camcorder or place the battery on the
Camcorder, and the built-in lithium battery will
be recharged. Leave the Camcorder as is for
approx. 24 hours, and the battery will drive the
date and time for approx. 6 months. (Even if the
[OFF/ON] switch is set to [OFF], the battery is
still being recharged.)
ENTER
VAR.
SEARCH
MENU
ENTER
VAR.
SEARCH
MENU
ENTER
VAR.
SEARCH
MENU
LSQT0860ENG.book 20 ページ 2004年12月22日 水曜日 午後2時38分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152

Panasonic PVGS65 Mode d'emploi

Catégorie
Caméscopes
Taper
Mode d'emploi

dans d''autres langues