Shenzhen Omni Intelligent Technology G3 IoT Device Manuel utilisateur

G3 IoT Device
Marque
Shenzhen Omni Intelligent Technology
Modèle
G3 IoT Device
Taper
Manuel utilisateur
欧米智能
Product Name: IOT device
Product Model: G3-KS-OM-NA-P
G3-iot Controller using manual
欧米智能
I. Product introduction
This is a sharing scooter iot controller, through 4G GPS, BLE5.2 Bluetooth and
smart phone APP for data communication to control the startup/shutdown of
the scooter, the cloud server automatically counts the time and deducts the fee.
II. Product working frequency band
NO.
Item
Frequency Band
Max launch Power
1
network
3G: WCDMA
B2
0.2W
B5
0.398W
2
network
4G: FDD-LTE
B2
0.2W
B4
0.251W
B12
0.251W
3
Bluetooth
2402-2480MHz
-13 dBm
4
GPS
1561.098MHz, 1575.42MHz
1602.5625MHz
Only receive, not transmit
III．APP installation and registration:
1.For APP download, please go to the official website of corresponding to the
mobile phone operating system to download and install it.
2.User account registration and login. This step requires the mobile phone to
be connected to the Internet, and the user account is a normal mobile phone
number .
3.Deposit recharge, car fare recharge .
IV．On/off operation instructions:
1.Turn on Bluetooth in the mobile phone system.
2.Open the APP, click the QR code button in the middle below the APP, enter
the scan QR code page, and scan the QR code with the iot controller. When the
mobile phone scans and reads the QR code information, the lock will automatically
open and enter the state of using the car.
欧米智能
3．When the car is used up, click close the lock, the cloud service will
automatically stop the time counting and deduct the charge after receiving the
lock.
V．The IOT controller needs to be used with a smart phone, and the mobile phone
hardware environment requires：
Android 4.3 or above, hardware support Bluetooth 4.0BLE, the best screen
resolution is 1280x720; IOS 7.1 or above, iphone 4s or above.
VI．APP page introduction
home page
欧米智能
Scan the QR code page
Unlock and using car page
欧米智能
Successful deduction page
VII. CAUTION
Risk of explosion if the battery is replaced by an incorrect type;
disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of
a battery, that can result in an explosion;
leaving a battery in an extremely high temperature surrounding environment that
can result in an explosion or the leakage of flammable liquid or gas;
a battery subjected to extremely low air pressure that may result in an explosion or
the leakage of flammable liquid or gas
Statement:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
欧米智能
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1.This device may not cause harmful interference.
2.This device must accept any interference received, including interference that
may cause undesired operation.
Statement:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC and IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the your body.
Cet équipement est conforme aux limites d'exposition aux rayonnements spécifiées
par fac et IC pour les environnements non contrôlés. L'équipement doit être
installé et utilisé à une distance minimale de 20 cm du corps.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
欧米智能
cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Shenzhen Omni Intelligent Technology G3 IoT Device Manuel utilisateur

G3 IoT Device
Marque
Shenzhen Omni Intelligent Technology
Modèle
G3 IoT Device
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents