Ryobi P4361 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
18 VOLT POLE SAW
SCIE DE MANCHE 18 V
SIERRA DE PÉRTIGA DE 18 V
P4360
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
TABLE OF CONTENTS
Important Safety Instructions .......... 2-3
Specific Safety Rules ...................... 3-4
Symbols .......................................... 5-6
Features .......................................... 7-8
Assembly ...................................... 8-10
Operation .................................... 10-13
Maintenance ............................... 14-18
Troubleshooting ................................19
Parts Ordering/Service ........ Back Page
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation
avant d’employer ce produit.
TABLE DES MATIÈRES
Instructions importantes
concernant la sécurité..................... 2-3
Règles de sécurité particulières ...... 3-4
Symboles ........................................ 5-6
Caractéristiques .............................. 7-8
Assemblage .................................. 8-10
Utilisation .................................... 10-13
Entretien ...................................... 14-19
Dépannage ........................................ 19
Commande de pièces/
réparation .......................... Páge arrière
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe
leer y comprender el manual del
operador antes de usar este producto.
ÍNDICE DE CONTENIDO
Instrucciones de seguridad
importantes ..................................... 2-3
Reglas de seguridad específicas .... 3-4
Símbolos ......................................... 5-6
Características ................................ 7-8
Armado ......................................... 8-10
Funcionamiento .......................... 10-13
Mantenimiento ............................ 14-19
Solución de problemas .....................19
Pedidos de piezas/
servicio ........................... Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
2 — English
WARNING:
Read and understand all instructions. Failure
to follow all instructions listed below may result
in electric shock, fire, and/or serious personal
injury.
READ ALL INSTRUCTIONS
For safe operation, read and understand all in-
structions before using this product. Be familiar
with all controls and proper use of the machine.
Follow all safety instructions. Failure to follow
all safety instructions listed below, can result in
serious personal injury.
Do not allow children or untrained individuals
to use this unit.
Thoroughly inspect the area where the equip-
ment is to be used and remove all foreign objects.
Wear eye protection with side shields, which is
marked to comply with ANSI Z87.1, along with
head protection when operating this equipment.
Dress Properly — Wear heavy long pants, long
sleeves, boots, and gloves. Do not wear loose
fitting clothing, short pants, sandals, or go bare-
foot. Do not wear jewelry of any kind.
Secure long hair above shoulder level to prevent
entanglement in moving parts.
Keep Children Away — Keep all bystanders,
children, and pets at least 50 ft. away.
Stay Alert — Watch what you are doing; use
common sense. Do not operate this unit when
you are tired, ill, upset, or under the influence
of alcohol, drugs, or medication.
Do not operate in poor lighting.
Use Safety Glasses — Always use face or dust
mask if operation is dusty.
Disconnect Appliance — Remove battery from
appliance when not in use, before servicing ,
when changing accessories such as bar chain.
Don’t Overreach — Keep proper footing and
balance at all times. Overreaching can result in
loss of balance or exposure to hot surfaces.
Keep all parts of your body away from any mov-
ing part.
Inspect the unit before each use for loose fasten-
ers, etc. Replace any damaged parts before use.
When not in use, product should be stored
indoors in a dry, locked up place — out of the
reach of children.
Use only original manufacturer’s replacement
parts. Failure to do so may cause poor perfor-
mance, possible injury, and will void your war-
ranty.
Do not, under any circumstance, use any at-
tachment or accessory on this product which
was not provided with the product or identified
as appropriate for use with this product in the
operator’s manual.
Avoid Dangerous Environments — Do not use
the product in damp or wet locations. Do not
use in rain.
Stop the motor, wait until all moving parts come
to a complete stop, and remove the battery pack
before cleaning or performing any maintenance.
Never use water or any liquids to clean or rinse
off your product and do not expose the product
to rain or wet conditions. Store indoors in a dry
area. Corrosive liquids, water, and chemicals
can enter the product’s electronic components
and/or battery compartment and damage elec-
tronic components and/or the battery pack,
which can result in a short circuit, increased risk
of fire, and serious personal injury. Remove any
buildup of dirt and debris by wiping the product
clean with a dry cloth occasionally.
Use the Right Appliance — Do not use the
product for any job except that for which it is
intended.
Do not operate from steps, a ladder, rooftop,
tree, or unstable support. Stable footing on a
solid surface enables better control of the prod-
uct in unexpected situations.
Do not force the product. It will do the job better
and with less likelihood of a risk of injury at the
rate for which it was designed.
DANGER — Keep hands away from cutting
area. Keep both hands on handles when power
is on.
IMPORTANT SAFETY INSTRUCTIONS
3 — English
Kickback is a dangerous reaction that can lead
to serious injury. Kickback may occur when the
moving chain contacts an object at the upper
portion of the tip of the guide bar or when the
wood closes in and pinches the chain in the
cut. Contact at the upper portion of the tip of
the guide bar can cause the chain to dig into
the object and stop the chain for an instant.
The result is a lightning-fast, reverse reaction
which kicks the guide bar up and back toward
the operator. If the chain is pinched along the
top of the guide bar, the guide bar can be driven
rapidly back toward the operator, which can
cause loss of control and may result in serious
injury. Do not rely exclusively upon the safety
devices built into the product.
With a basic understanding of kickback, you
can reduce or eliminate the element of surprise.
Sudden surprise contributes to accidents.
Use pole saw for cutting wood only. Do not use
for cutting non-wood items.
Make sure that the area in which you are cutting
is free from obstructions. Do not let the nose of
the guide bar contact a log, branch, fence, or
any other obstruction while you are operating
the unit. Have a planned retreat path.
Cut only when visibility and light are adequate
for you to see clearly.
To protect yourself from electrocution, do not
operate within 50 feet of overhead electrical
lines.
In an emergency situation, use the spring clips
on the quick release shoulder harness to free
yourself from the harness and the pole saw.
WARNING — Do not operate near electrical
power lines. The unit has not been designed
to provide protection from electric shock in the
event of contact with overhead electric lines.
Consult local regulations for safe distances from
overhead electric power lines and ensure that
the operating position is safe and secure before
operating the saw chain pole pruner.
Before starting the motor, make sure the chain
is not contacting any object.
To protect yourself from falling branches, do not
stand directly under the branch or limb being
cut. This unit should not be held at an angle over
60° from ground level.
Turn off the motor and make sure cutting attach-
ment has stopped before setting unit down.
Follow the sharpening and maintenance instruc-
tions for the saw chain.
Use only the replacement guide bars and low
kickback chains specified for the unit.
Do not operate the saw with one hand! Serious
injury to the operator, helpers, bystanders, or
any combination of these persons may result
from one hand operation. This saw is intended
for two-handed use.
Use extreme caution when cutting small-sized
brush and saplings because slender material
may catch the saw chain and be whipped to-
ward you or pull you off balance.
SPECIFIC SAFETY RULES
IMPORTANT SAFETY INSTRUCTIONS
CAUTION — Blade coasts after being turned
off.
Do not grasp the exposed cutting blades or
cutting edges when picking up or holding the
product.
Check Damaged Parts — Before further use of
the product, a guard or other part that is dam-
aged should be carefully checked to determine
that it will operate properly and perform its
intended function. Check for alignment of mov-
ing parts, binding of moving parts, breakage of
parts, mounting, and any other condition that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
indicated elsewhere in this manual.
4 — English
SPECIFIC SAFETY RULES
When cutting a limb that is under tension, be
alert for spring back so that you will not be struck
when the tension in the wood fibers is released.
To avoid accidental starting, never carry the unit
with the battery installed or with your finger on
the switch trigger.
Maintain Product With Care — Keep cutting
edge sharp and clean for best performance
and to reduce the risk of injury. Follow instruc-
tions for lubricating and changing accessories.
Inspect the battery charger cord periodically,
and if damaged, have it replaced or repaired by
an authorized service dealer.
Keep handles dry, clean, and free from oil and
grease.
Service on the product must be performed by
qualified repair personnel only. Service or main-
tenance performed by unqualified personnel
could result in injury to the user or damage to
the product.
Battery operated units do not have to be plugged
into an electrical outlet; therefore, they are al-
ways in operating condition. Be aware of pos-
sible hazards even when unit is not operating.
Remove the battery pack from the pole saw
before cleaning, servicing, storing, removing
material from the unit, changing accessories
such as the bar and chain, or when not in use.
A battery pack must be recharged only with the
specified charger for the battery pack. A charger
that may be suitable for one type of battery pack
may create a risk of fire when used with another
battery pack. Use battery pack only with charger
listed.
Use this product only with batteries and char-
gers listed in tool/appliance/battery pack/char-
ger correlation supplement 987000-432.
To reduce the risk of explosion and possible in-
jury, do not place battery units or their batteries
near fire or heat.
Do not open or mutilate the battery pack. Re-
leased electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
Do not charge appliance in the rain or in a wet
or damp location. Following this rule will reduce
the risk of electric shock.
Do not dispose of batteries in a fire. The cell
may explode. Batteries should be recycled, con-
sult your local waste authority for information
regarding available recycling and/or disposal
options.
Exercise care in handling batteries in order not
to short terminals. When battery pack is not in
use, keep it away from other metal objects like:
paper clips, coins, keys, nails, screws, or other
small metal objects that can make a connection
from one terminal to another. Shorting the bat-
tery pack terminals together may cause sparks,
burns, or a fire.
Save these instructions. Refer to them frequent-
ly and use them to instruct others who may use
this product. If you loan someone this product,
loan them these instructions also to prevent
misuse of the product and possible injury.
SPECIFIC SAFETY RULES
SAVE THESE INSTRUCTIONS
5 — English
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and
understand operator’s manual before using this
product.
Wear Eye and Head
Protection
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with head
protection when operating this equipment.
Wet Conditions Alert
Do not expose battery, battery compartment, or
electronic components to rain, water, or liquids.
Do not charge battery or expose product to rain or
damp locations.
Gloves
Wear non-slip, heavy-duty protective gloves when
handling the pole saw and the blade.
Safety Footwear
Wear non-slip safety footwear when using this
equipment.
The following signal words and meanings are intended to explain the levels of risk associated with
this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates a hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a hazardous situation, that, if not avoided, may result in
minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates information considered
important, but not related to a potential injury (e.g. messages
relating to property damage).
SYMBOLS
6 — English
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME EXPLANATION
Keep Tool Away from
Electrical Lines/Keep
Bystanders Away
DANGER! Risk of electrocution! Keep tool 50 feet
away from electrical lines. Keep all bystanders at
least 50 ft. away.
Electric Shock
Failure to use in dry conditions and to observe safe
practices can result in electric shock.
No Hands Symbol
Failure to keep your hands away from the blade will
result in serious personal injury.
Recycle Symbol
This product uses lithium-ion batteries. Local, state
or federal laws may prohibit disposal of batteries in
ordinary trash. Consult your local waste authority
for information regarding available recycling and/
or disposal options.
V Volts Voltage
Direct Current Type or a characteristic of current
SYMBOLS
7 — English
PRODUCT SPECIFICATIONS
Motor ..................................................................................................................................... 18 Volt DC
Bar Length ....................................................................................................................................... 8 in.
Cutting Capacity.............................................................................................................................. 6 in.
Chain Pitch ....................................................................................................................................3/8 in.
Chain Type ................................................................................................................................Standard
Fig. 1
SWITCH
TRIGGER
TRIGGER
LOCK-OUT
INTERMEDIATE
POLE
OIL CAP
SCABBARD
FEATURES
QUICK RELEASE
SHOULDER
HARNESS
COMBINATION
WRENCH
HANDLE
POLE
CUTTING HEAD
POLE
8 — English
KNOW YOUR POLE SAW
See Figure 1.
The safe use of this product requires an under-
standing of the information on the product and
in this operator’s manual as well as a knowledge
of the project you are attempting. Before use of
this product, familiarize yourself with all operating
features and safety rules.
AUTOMATIC OILER SYSTEM
Lubrication is provided by the automatic oiler sys-
tem. The oiler is driven by the sprocket and adds
lubrication only when the chain is moving.
QUICK-VIEW OIL INDICATOR
Semi-transparent bar lube reservoir that allows
user to see when to add lubricant.
SCABBARD
The scabbard keeps the operator from coming in
contact with the sharp blades when the tool is not
in use. It also helps keep the blades from being
nicked or damaged when the tool is in storage.
TRIGGER LOCK-OUT
The trigger lock-out prevents unintentional starting
of the pole saw.
UNPACKING
This product requires assembly.
Carefully remove the product and any acces-
sories from the box. Make sure that all items
listed in the Packing List are included.
WARNING:
Do not use this product if any parts on the
Packing List are already assembled to your
product when you unpack it. Parts on this list
are not assembled to the product by the manu-
facturer and require customer installation. Use
of a product that may have been improperly as-
sembled could result in serious personal injury.
Inspect the product carefully to make sure no
breakage or damage occurred during shipping.
Do not discard the packing material until you
have carefully inspected and satisfactorily oper-
ated the product.
If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Cutting Head Pole
Intermediate Pole
Handle Pole
Scabbard
Combination Wrench
Quick Release Shoulder Harness
Operator’s Manual
WARNING:
If any parts are damaged or missing, do not
operate this product until the parts are replaced.
Use of this product with damaged or missing
parts could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condi-
tion leading to possible serious personal injury.
FEATURES
ASSEMBLY
AUTOMATIC OILER SYSTEM RY3714,
RY40505
9 — English
Fig. 2
WARNING:
To prevent accidental starting that could cause
serious personal injury, always remove the bat-
tery pack from the product when assembling
parts.
CONNECTING THE POLES
See Figure 2.
Insert the plug on the intermediate pole into the
socket on the handle pole and push together
until fully seated. The plug is larger on one side
and will only install one way.
Lower the collar on the handle pole to the
threaded base on the intermediate pole and
rotate clockwise to secure.
Repeat this process to attach the intermediate
pole to the cutting head pole.
NOTE: When assembled correctly, handle pole
and cutting head pole should not be able to sepa-
rate from intermediate pole when pulled. Repeat
above steps if poles can be separated from inter-
mediate pole.
WARNING:
Failure to securely assembly and lock all poles
together as directed above could cause the
poles to separate and could result in serious
personal injury or death.
ASSEMBLY
HANDLE
POLE
INTERMEDIATE POLE
THREADED
BASE
THREADED BASE
CUTTING HEAD
POLE
COLLAR
COLLAR
PLUG
SOCKET
10 — English
ASSEMBLY
ATTACHING THE QUICK RELEASE
SHOULDER HARNESS
See Figure 3.
To prevent back and shoulder fatigue, always use
the quick release shoulder harness when operat-
ing this tool. If your back or shoulders become
sore, take a break and then adjust the position of
the harness.
Squeeze and hold the latch on the spring clip.
Place the spring clip onto the strap hanger and
release the latch.
Repeat to secure second spring clip.
Place the strap around your shoulder and adjust
it to a comfortable position.
Fig. 3
OPERATION
DANGER:
Never cut near power lines, electric cords, or
other electric sources. If bar and chain jams
on any electrical cord or line, DO NOT TOUCH
THE BAR OR CHAIN! THEY CAN BECOME
ELECTRICALLY LIVE AND VERY DANGEROUS.
Continue to hold the pole saw by the insulated
rear handle or lay it down and away from you in
a safe manner. Disconnect the electrical service
to the damaged line or cord before attempting
to free the bar and chain from the line or cord.
Contact with the bar, chain, other conductive
parts of the pole saw, or live electric cords or
lines will result in death by electrocution or seri-
ous injury.
WARNING:
Do not allow familiarity with this product to
make you careless. Remember that a careless
fraction of a second is sufficient to inflict seri-
ous injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
head protection. Failure to do so could result in
objects being thrown into your eyes and other
possible serious injuries.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this prod-
uct. The use of attachments or accessories not
recommended can result in serious personal injury.
NOTICE:
Before each use, inspect the entire product
for damaged, missing, or loose parts such as
screws, nuts, bolts, caps, etc. Tighten securely
all fasteners and caps and do not operate this
product until all missing or damaged parts are
replaced. Please contact customer service or
an authorized service center for assistance.
APPLICATIONS
You may use this product for the purposes listed
below:
Limbing
Pruning
SPRING
CLIP
SPRING
CLIP
LATCH
STRAP
HANGERS
11 — English
CHAIN
LUBRICANT
Fig. 4
CAP
QUICK VIEW
OIL INDICATOR
OPERATION
Fig. 5
LOCK-OUT
BUTTON
SWITCH TRIGGER
BATTERY
ADDING BAR AND CHAIN LUBRICANT
(NOT INCLUDED)
See Figure 4.
Use Premium Bar and Chain Lubricant (not includ-
ed). It is designed for chains and chain oilers, and
is formulated to perform over a wide temperature
range with no dilution required.
NOTE: Pole saw comes from the factory with no
bar and chain lubricant added. Level should also
be checked after every 20 minutes of use and
refilled as needed.
Remove oil cap.
Carefully pour the bar and chain lubricant into
the bar lube reservoir.
Wipe off excess oil.
Check and fill the reservoir when quick view oil
indicator is below the second to last indicator
line.
Repeat as needed.
NOTE: Do not use dirty, used or otherwise
contaminated oils. Damage may occur to the
bar or chain.
NOTE: It is normal for oil to seep from the saw
when not in use. To prevent seepage, empty the
oil tank after each use then run for one minute.
When storing the unit for a long period of time
(three months or longer) be sure the chain is lightly
lubricated; this will prevent rust on the chain and
bar sprocket.
TO INSTALL/REMOVE BATTERY PACK
See Figure 5.
WARNING:
Always remove battery pack from your tool
when you are assembling parts, making adjust-
ments, cleaning, carrying, transporting or when
not in use. Removing battery pack will prevent
accidental starting that could cause serious
personal injury.
NOTE: To avoid serious personal injury, always
remove the battery pack and keep hands clear of
the lock-out button when carrying or transporting
the tool.
To install:
Place the battery pack in the pole saw. Align
raised rib on battery pack with groove in battery
port.
WARNING:
Make sure the latches on the battery pack snap
in place and the battery pack is fully seated
and secure in the battery port before beginning
operation. Failure to securely seat the battery
pack could cause the battery pack to fall out,
resulting in serious personal injury.
12 — English
To remove:
Locate latches on side of battery pack and de-
press both sides to release the battery pack from
the pole saw.
For complete charging instructions, see the opera-
tor’s manuals for your battery pack and charger.
STARTING AND STOPPING
See Figure 6.
To start the motor:
Hold the pole saw as shown and ensure that you
are well away from anything that may contact
the blade.
Press and hold the trigger lock-out.
Depress the switch trigger.
To stop the motor:
Release the trigger to stop the pole saw. Upon
release of the trigger, the trigger lock will auto-
matically reset to the locked position.
PREPARATION FOR CUTTING
See Figures 7 - 8.
Wear non-slip gloves for maximum grip and
protection.
Maintain a proper grip on the unit whenever the
motor is running. Use your right hand to firmly
grip the rear handle while your left hand has a
firm grip on the pole shaft.
Hold unit firmly with both hands. Always keep
your left hand on the pole shaft and your right
hand on the rear handle, so your body is to the
left of the chain line. Never use a left-handed
(cross-handed) grip, or any stance that places
your body or arm across the chain line.
Never stand directly under the limb you are cut-
ting.
Be certain the collars are fully tightened before
operating equipment; check them periodically
for tightness during use to avoid serious injury.
BASIC CUTTING PROCEDURE
Follow the steps below to prevent damage to tree
or shrub bark. Do not use a back-and-forth saw-
ing motion.
Make a shallow first cut (1/4 of limb diameter)
on the underside of the limb close to the main
limb or trunk.
OPERATION
Fig. 6
FINAL
CUT
SECOND CUT
FIRST CUT
1/4 DIAMETER
LOAD
Fig. 7
CUTTING GUIDE
Fig. 8
Make a second cut from the top side of the limb
outboard from the first cut. Continue the cut
through the limb until the limb separates from
the tree. Be prepared to balance the weight of
the tool when the limb falls.
Make a final cut close to trunk.
NOTE: For second and final cuts (from top of limb
or branch), hold front cutting guide against the
limb being cut. This will help steady the limb and
13 — English
make it easier to cut. Allow chain to cut for you;
exert only light downward pressure. If you force the
cut, damage to the bar, chain, or motor can result.
Release the trigger as soon as the cut is com-
pleted.
Failure to follow proper cutting procedures will
result in the bar and chain binding and becom-
ing pinched or trapped in the limb. If this should
happen:
Stop the motor and remove the battery pack.
If the limb can be reached from the ground,
lift the limb while holding the saw. This should
release the “pinch” and free the saw.
If the saw is still trapped, call a professional for
assistance.
LIMBING AND PRUNING
See Figures 9 - 10.
This unit is designed for trimming small branches
and limbs up to 6 in. in diameter. For best results,
observe the following precautions.
Plan the cut carefully. Be aware of the direction
in which the branch will fall.
Branches may fall in unexpected directions. Do
not stand directly under the branch being cut.
The most typical cutting application is to posi-
tion the unit at an angle of 60° or less, depend-
ing on the specific situation, as shown. As the
angle of the pole saw shaft to ground increases,
the difficulty of making the first cut (from the
underside of limb) increases.
Remove long branches in several stages.
Cut lower branches first to allow the top branch-
es more room to fall.
Work slowly, keeping both hands on the saw
with a firm grip. Maintain secure footing and
balance.
Keep the tree between you and the chain while
limbing. Cut from side of tree opposite branch
you are cutting.
Do not cut from a ladder; this is extremely dan-
gerous. Leave this operation for professionals.
Do not make the flush cut next to the main limb
or trunk until you have cut off the limb further out
to reduce the weight. Following proper cutting
procedures will prevent stripping the bark from
the main member.
Do not use the pole saw for felling or bucking.
To prevent electrocution, do not operate within
50 ft. of overhead electrical lines.
Keep bystanders at least 50 ft. away.
OPERATION
Fig. 9
Fig. 10
60° MAXIMUM
14 — English
WARNING:
Before inspecting, cleaning, or servicing the
unit, stop the motor, wait for all moving parts
to stop, and remove the battery pack. Failure
to follow these instructions can result in serious
personal injury or property damage.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1, along with
head protection. Failure to do so could result in
objects being thrown into your eyes and other
possible serious injuries.
WARNING:
Never use water or any liquids to clean or rinse
off your product and do not expose the product
to rain or wet conditions. Store indoors in a dry
area. Corrosive liquids, water, and chemicals
can enter the product’s electronic components
and/or battery compartment and damage elec-
tronic components and/or the battery pack,
which can result in a short circuit, increased risk
of fire, and serious personal injury. Remove any
buildup of dirt and debris by wiping the product
clean with a dry cloth occasionally.
WARNING:
When servicing, use only identical replacement
parts. Use of any other parts could create a
hazard or cause product damage.
NOTICE:
Periodically inspect the entire product for dam-
aged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fas-
teners and caps and do not operate this product
until all missing or damaged parts are replaced.
Please contact customer service or an autho-
rized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and may be
damaged by their use. Use clean cloths to remove
dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken, or destroy plastic, which could
result in serious personal injury.
All pole saw service, other than the items listed in
these maintenance instructions, should be per-
formed by competent pole saw service personnel.
(For example, if improper tool is used to hold the
flywheel in order to remove the clutch, structural
damage to the flywheel could occur and subse-
quently could cause the flywheel to burst).
REPLACING THE BAR AND CHAIN
See Figures 11 - 14.
WARNING:
To avoid possible serious injury, stop the motor
and remove the battery pack before replacing
the bar, chain, or performing any maintenance
operation.
Using the combination wrench provided, re-
move the chain cover screw, washer, and chain
cover from the chain saw.
The bar contains a slot that fits over the mount-
ing post. The bar also contains a chain tension-
ing pin hole which fits over the chain tensioning
pin inside the chain cover.
MAINTENANCE
BAR
CHAIN
COVER
CHAIN COVER SCREW
CHAIN
Fig. 11
15 — English
Place the bar onto the mounting post.
Fit the chain over the sprocket and into the bar
groove. The cutters on the top of the bar should
face toward the bar tip, in the direction of the
chain rotation.
Replace the chain cover ensuring that the chain
tensioning pin in the cover is in the chain ten-
sioning pin hole in the bar.
NOTE: If necessary, rotate the chain tensioning
screw counterclockwise until the pin and hole
can be aligned.
Remove all slack from chain by turning the
chain tensioning screw clockwise, assuring
that the chain seats into the bar groove during
tensioning.
Tighten the chain cover screw securely.
NOTE:
Chain is correctly tensioned when there is
no slack on the underside of the bar, the chain is
snug, but it can be turned by hand without binding.
If chain is too tight, it will not rotate. Loosen the
chain cover screw slightly and turn chain tension-
ing screw 1/4 turn counterclockwise. Retighten
chain cover screw securely.
CHAIN
ROTATION
CHAIN
SPROCKET
Fig. 13
MAINTENANCE
Fig. 12
Fig. 14
MOUNTING
POST
CHAIN
COVER
CHAIN
TENSIONING
PIN
CHAIN
COVER
SCREW
LOCK
WASHER
MOUNTING
POST SLOT
MOUNTING
POST
CHAIN
TENSIONING
PIN HOLE
BAR
SPROCKET
COMBINATION
WRENCH
CHAIN
TENSIONING
SCREW
16 — English
APPROX .050 in.
Fig. 16
Fig. 15
ADJUSTING THE CHAIN TENSION
See Figures 15 - 16.
WARNING:
Stop the motor, wait for all moving parts to stop,
and remove the battery pack. Never touch or
adjust the chain while the motor is running. The
saw chain is very sharp. Always wear protective
gloves when performing maintenance to the
chain. Failure to follow these instructions can
result in serious personal injury.
Proper chain tension is critical to the performance
of your pole saw. Always check chain tension
before using the saw and periodically until the
work is complete. The chain must be retensioned
whenever the flats on the drive links hang out of
the bar groove.
A cold chain is correctly tensioned when there is
no slack on the underside of the guide bar. The
chain should be snug, but still able to be turned
by hand without binding.
A warm chain is correctly tensioned when the flats
on the tie straps hang approximately .050 inches
out of the bar groove.
If adjustment is needed:
Loosen the chain cover screw to finger tight.
Turn the chain tensioning screw clockwise until
the flats on the tie straps of the chain contact
the bar, making sure the drive links are seated
inside the bar groove.
Tighten the chain cover screw securely.
Verify the chain is now correctly tensioned using
the guidelines above.
NOTE: New chains tend to stretch; check the
chain tension frequently and adjust as needed.
NOTICE:
A chain tensioned while warm may be too tight
upon cooling. Check the “cold tension” before
next use.
Fig. 17
REMOVE
CAP
BAR LUBE
RESERVOIR
MAINTENANCE
CHAIN OILER
See Figure 17.
Use premium bar and chain lubricant. It is de-
signed for chains and chain oilers and is formu-
lated to perform over a wide temperature range
with no dilution required.
Remove the cap and carefully pour approxi-
mately 2 oz. of bar and chain lubricant into the
bar lube reservoir.
Replace the cap and tighten securely.
Check and refill the bar lube reservoir every time
the pole saw is used.
NOTE: Do not use dirty, used, or otherwise con-
taminated lubricants. Damage may occur to the
oil pump, bar, or chain.
FLATS ON TIE STRAPS
17 — English
Fig. 18
RAKER (DEPTH GAUGE)
CLEARANCE
.025 in.
CUTTING
CORNER
SIDE PLATE
DEPTH GAUGE
TOE
GULLET
HEEL
RIVET HOLE
TOP
PLATE
PARTS OF A CUTTER
Fig. 19
CHAIN MAINTENANCE
See Figure 18.
WARNING:
Remove the battery pack and make sure the
chain has stopped before you do any work on
the saw to avoid accidental starting and pos-
sible serious personal injury.
For smooth and fast cutting, the chain needs to
be maintained properly. The following conditions
indicate that the chain requires sharpening:
Wood chips are small and powdery
Chain must be forced through the wood during
cutting
Chain cuts to one side
During maintenance of the chain, consider the
following:
Improper filing angle of the side plate can in-
crease the risk of a severe kickback.
Depth gauge (or raker clearance) setting de-
termines the height the cutter enters the wood
and the size of the wood chip that is removed.
Too much clearance increases the potential for
kickback. Too little clearance decreases the size
of the wood chip thus decreasing the chain's
cutting ability.
If cutter teeth have hit hard objects such as nails
and stones, or have been abraded by mud or
sand on the wood, have service dealer sharpen
chain.
HOW TO SHARPEN THE CUTTERS
See Figures 19 - 22.
Be careful to file all cutters to the specified angles
and to the same length, as fast cutting can be
obtained only when all cutters are uniform.
WARNING:
The saw chain is very sharp, always wear pro-
tective gloves when performing maintenance
to the chain to prevent serious personal injury.
Properly tension the chain prior to sharpening.
Refer to Adjusting the Chain Tension earlier in
this manual. Do all of your filing at the mid-point
of the bar.
MAINTENANCE
Fig. 20
Use a 5/32 in. diameter round file and holder.
Keep the file level with the top plate of the tooth.
Do not let the file dip or rock.
Using light but firm pressure, stroke towards
the front corner of the tooth. Lift file away from
the steel on each return stroke.
Put a few firm strokes on every tooth. File all left
hand cutters in one direction. Then move to the
other side and file the right hand cutters in the
opposite direction. Occasionally remove filings
from the file with a wire brush.
18 — English
WARNING:
Improper chain sharpening increases the po-
tential of kickback, which can result in serious
personal injury.
WARNING:
Failure to replace or repair damaged chain can
cause serious injury.
NOTICE:
A dull or improperly sharpened chain can cause
excessive engine speed during cutting, which
may result in severe engine damage.
STORING THE PRODUCT
See Figure 23.
WARNING:
Always remove the battery pack before trans-
porting or storing chain saw. Place battery pack
indoors in a dry, secure location out of the reach
of children when storing. Failure to follow these
instructions may lead to accidental starting or
unauthorized use and result in serious personal
injury.
Clean all foreign material from the product. Store
idle unit indoors in a dry, well-ventilated area
that is inaccessible to children. Keep away from
corrosive agents such as garden chemicals and
de-icing salts.
Always place the scabbard on the saw bar
when transporting or storing the pole saw. The
scabbard is a snug fit and must be attached
very carefully due to the sharp teeth on the
saw chain. This is best done by grasping the
scabbard at one end, in the center portion of
Fig. 23
SCABBARD
MAINTENANCE
LEFT HAND
CUTTERS
RIGHT HAND
CUTTERS
Fig. 22
Fig. 21
the scabbard, and carefully sliding it over the
chain as shown. Use caution to avoid the sharp
teeth of the chain.
NOTE: The saw chain is very sharp. Always
wear protective gloves when handling the chain.
19 — English
PROBLEM CAUSE SOLUTION
Bar and chain
running hot and
smoking.
Check chain tension
for overtightened
condition
Bar lube reservoir
empty
Tension chain. Refer to Adjusting the Chain Tension
earlier in this manual.
Check bar lube reservoir.
Motor runs,
but chain is not
rotating.
Chain tension too
tight.
Check guide bar and
chain assembly.
Check guide bar and
chain for damage.
Retension chain. Refer to Adjusting the Chain Tension
earlier in this manual.
Refer to Replacing the Bar and Chain earlier in this
manual.
Inspect guide bar and chain for damage.
TROUBLESHOOTING
This product has a Three-year Limited Warranty for personal,
family, or household use (90 days for business or commercial use).
For warranty details, visit www.ryobitools.com
or call (toll free) 1-800-525-2579.
2 — Français
AVERTISSEMENT :
Lire et veiller à bien comprendre toutes les
instructions. Le non-respect des instructions
ci-dessous peut entraîner une électrocution, un
incendie et des blessures graves.
LIRE TOUTES LES INSTRUCTIONS
Pour travailler en toute sécurité, lire et veiller à
bien comprendre toutes les instructions avant
d’utiliser ce produit. Familarisez-vous avec toutes
les commandes et l’utilisation correcte de l’outil.
Respecter toutes les instructions de sécurité.
Le non respect des instructions de sécurité ci-
dessous peut entraîner des blessures graves.
Ne pas laisser des enfants ou personnes n’ayant
pas reçu une formation adéquate utiliser cet outil.
Inspecter soigneusement la zone de travail et
retirer tout corps étranger.
Porter une protection oculaire avec écrans
latéraux certifiée conforme à la norme ANSI
Z87.1, ainsi qu’une protection casque lors de
l’utilisation de cet outil.
Porter une tenue appropriée — Porter des
pantalons longs, des manches longs, des
chaussures et des gants épais. Ne pas porter
de vêtements amples, bijoux, shorts, sandales
et ne pas travailler pieds nus. Ne porter aucun
bijou.
Attacher les cheveux longs pour les maintenir
au-dessus des épaules, afin qu’ils ne se prennent
pas dans les pièces en mouvement.
Tenir à l’écart des enfants — Garder les badauds,
enfants et animaux à une distance de 15 m (50 pi)
minimum.
Rester attentif — Prêter attention au travail et
faire prevue de bon sens. Ne pas utiliser ce taille-
bordures en état de fatigue, si l’on est souffrant,
contrarié ou sous l’influence de l’alcool, de
drogues ou de médicaments.
Ne pas travailler sous un éclairage insuffisant.
Porter des lunettes de sécurité — Toujours porter
un masque facial ou un masque anti-poussière
si le travail produit de la poussière.
Débrancher l’appareil — Retirer la batterie de
appareils lorsque l’outil n’est pas en usage,
avant son entretien ou lors du remplacement
d’accessoires tels que le guide chaîne.
Ne pas travailler hors de portée — Toujours se
tenir bien campé et en équilibre. Le travail hors
de portée risque de faire perdre l’équilibre ou
de causer un contact avec les pièces brûlantes.
Garder toutes les parties du corps à l’écart des
pièces en mouvement.
Inspecter l’outil avant chaque utilisation pour
s’assurer qu’il n’y a pas de pièces desserrées,
etc. Remplacer les pièces endommagées avant
utilisation.
Quand la produit n’est pas utilisée, elle devrait
être entreposée à l’intérieur, dans un endroit sec
et sécuritaire - loin de la portée des enfants.
Utiliser exclusivement des pièces de rechange
d’origine. Toute dérogation peut entraîner un
mauvais fonctionnement, des blessures graves
et l’annulation de la garantie.
N’utiliser en aucun cas un accessoire non fourni
avec le produit, ou indiqué comme pouvant être
utilisé sur l’outil dans le manuel d’utilisation.
Éviter les environnements dangereux — Ne pas
utiliser l’accessoire dans des endroits humides
ou mouillés. Ne pas utiliser sous la pluie.
Arrêter le moteur, attendre que toutes les pièces
en mouvement cessent de bouger et retirer le
bloc-piles avant tout nettoyage ou entretien.
Ne jamais utiliser de l’eau ou une autre liquide
pour nettoyer ou rincer la produit et n’exposez
pas à la pluie ou conditions l’humidité. La remiser
à l’intérieur dans un endroit sec. Les liquides
corrosifs, l’eau et les produits chimiques peuvent
s’infiltrer dans le composants électroniques et/
ou le compartiment de la pile et endommager les
composants électroniques et/ou le bloc-pile, ce
qui peut entraîner un court-circuit, augmenter le
risque d’incendie ou des blessures corporelles
graves. Enlever toute accumulation de la saleté
et les débris sur la produit de temps en temps
avec un linge sec.
Utilisez l’outil approprié — N’utilisez pas le
produit pour aucune tâche sauf celle pour
laquelle elle est conçue.
Ne pas fonctionner l’outil sur des étapes, une
échelle, un toit, un arbre, ou un support instable.
Une position stable sur une surface ferme permet
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56

Ryobi P4361 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire

dans d''autres langues