Canon IXUS 115 HS Manuel utilisateur

CEL-SQ6XA2M1

Getting Started

ENGLISH

Guide de mise en route

FRANÇAIS

Getting Started

ENGLISH

• Make sure you read this guide, including the “Safety

Precautions” section, before using the camera.

• Store this guide safely so that you can use it in the future.

Please refer to the complete user guide included

on the DIGITAL CAMERA Manuals Disk for more

detailed information.

2

Check if the following items are included in your camera package.

If anything is missing, contact the retailer where you purchased the camera.

Using the Manuals

Also refer to the manuals on the DIGITAL CAMERA Manuals Disk.

• Camera User Guide

Once you have mastered the basics, use the camera’s many

features to shoot more challenging photos.

• Software Guide

Read when you want to use the included software.

• A memory card is not included.

• Adobe Reader is required to view the PDF manuals. Microsoft Word/

Word Viewer can be installed to view the Word manuals (required only for

manuals for the Middle East).

Checking the Package Contents

Battery Charger

CB-2LV/CB-2LVE

Camera Battery Pack NB-4L

(with Terminal Cover)

AV Cable

AVC-DC400

Interface Cable

IFC-400PCU

Wrist Strap

WS-DC11

Getting Started

(This Guide)

DIGITAL CAMERA

Solution Disk

Warranty System

Booklet

3

Test Shots and Disclaimer

Take some initial test shots and play them back to make sure the images

were recorded correctly. Please note that Canon Inc., its subsidiaries and

affiliates, and its distributors are not liable for any consequential damages

arising from any malfunction of a camera or accessory, including memory

cards, that results in the failure of an image to be recorded or to be recorded

in a way that is machine readable.

Warning Against Copyright Infringement

The images recorded with this camera are intended for personal use. Do not

record images that infringe upon copyright laws without the prior permission

of the copyright holder. Please be advised that in certain cases the copying

of images from performances, exhibitions, or commercial properties by

means of a camera or other device may contravene copyright or other legal

rights even if the image was shot for personal use.

Warranty Limitations

For information on your camera's warranty, please refer to the Canon

Warranty System Booklet supplied with your camera.

For Canon Customer Support contacts, please see the Warranty System

Booklet.

LCD Monitor (Screen)

• The LCD monitor is produced with extremely high-precision manufacturing

techniques. More than 99.99% of the pixels operate to specification, but

occasionally non-performing pixels may appear as bright or dark dots. This

is not a malfunction and has no effect on the recorded image.

• The LCD monitor may be covered with a thin plastic film for protection

against scratches during shipment. If so, remove the film before using the

camera.

Camera Body Temperature

Please take care when operating the camera for an extended period as the

camera body may become warm. This is not a malfunction.

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

CANON EUROPA N.V.

Bovenkerkerweg 59-61, 1185 XB Amstelveen, The Netherlands.

Read This First

4

• Before using the product, please ensure that you read the safety precautions described

below. Always ensure that the product is used correctly.

• The safety precautions noted on the following pages are intended to prevent injuries to

yourself and other persons, or damage to the equipment.

• Be sure to also check the guides included with any separately sold accessories you

use.

Warning

Denotes the possibility of serious injury or death.

• Do not trigger the flash in close proximity to people’s eyes.

Exposure to the intense light produced by the flash could damage eyesight. In particular,

remain at least one meter (39 inches) away from infants when using the flash.

• Store this equipment out of the reach of children and infants.

Strap: Putting the strap around a child’s neck could result in asphyxiation.

• Use only recommended power sources.

• Do not attempt to disassemble, alter or apply heat to the product.

• Avoid dropping or subjecting the product to severe impacts.

• To avoid the risk of injury, do not touch the interior of the product if it has been

dropped or otherwise damaged.

• Stop using the product immediately if it emits smoke, a strange smell, or

otherwise behaves abnormally.

• Do not use organic solvents such as alcohol, benzine, or thinner to clean the

equipment.

• Do not let the product come into contact with water (e.g. sea water) or other

liquids.

• Do not allow liquids or foreign objects to enter the camera.

This could result in electrical shock or fire.

If liquids or foreign objects come into contact with the camera interior, immediately turn

the camera power off and remove the battery.

If the battery charger becomes wet, unplug it from the outlet and consult your camera

distributor or a Canon Customer Support Help Desk.

• Use only the recommended battery.

• Do not place the battery near or in direct flame.

• Unplug the power cord periodically, and using a dry cloth, wipe away any dust

and dirt that has collected on the plug, the exterior of the power outlet, and the

surrounding area.

• Do not handle the power cord with wet hands.

• Do not use the equipment in a manner that exceeds the rated capacity of the

electrical outlet or wiring accessories. Do not use if the power cord or plug are

damaged, or not fully plugged into the outlet.

• Do not allow dirt or metal objects (such as pins or keys) to contact the terminals

or plug.

The battery may explode or leak, resulting in electrical shock or fire. This could cause

injury and damage the surroundings. In the event that a battery leaks and the battery acid

contacts eyes, mouth, skin or clothing, immediately flush with water.

Safety Precautions

5

• Turn the camera off in places where camera use is prohibited.

The electromagnetic waves emitted by the camera may interfere with the operation of

electronic instruments and other devices. Exercise adequate caution when using the

camera in places where use of electronic devices is restricted, such as inside airplanes

and medical facilities.

• Do not play the supplied CD-ROM(s) in any CD player that does not support data

CD-ROMs.

It is possible to suffer hearing loss from listening with headphones to the loud sounds of

a CD-ROM played on a music CD player. Additionally, playing the CD-ROM(s) in an audio

CD player (music player) could damage the speakers.

Caution

Denotes the possibility of injury.

• Be careful not to bang the camera or subject it to strong impacts or shocks when

hanging it by the strap.

• Be careful not to bump or push strongly on the lens.

This could lead to injury or damage the camera.

• Be careful not to subject the screen to strong impacts.

If the screen cracks, injury may result from the broken fragments.

• When using the flash, be careful not to cover it with your fingers or clothing.

This could result in burns or damage to the flash.

• Avoid using, placing or storing the product in the following places:

- Places subject to strong sunlight

- Places subject to temperatures above 40 °C (104 °F)

- Humid or dusty areas

These could cause leakage, overheating or an explosion of the battery, resulting in

electrical shock, fire, burns or other injuries.

High temperatures may cause deformation of the camera or battery charger casing.

• The slideshow transition effects may cause discomfort when viewed for

prolonged periods.

Caution

Denotes the possibility of damage to the equipment.

• Do not aim the camera at bright light sources (such as the sun on a clear day).

Doing so may damage the image sensor.

• When using the camera on a beach or at a windy location, be careful not to allow

dust or sand to enter the camera.

This may cause the product to malfunction.

Safety Precautions

6

• In regular use, small amounts of smoke may be emitted from the flash.

This is due to the high intensity of the flash burning dust and foreign materials stuck to the

front of the unit. Please use a cotton swab to remove dirt, dust or other foreign matter from

the flash to prevent heat build-up and damage to the unit.

• Remove and store the battery when you are not using the camera.

If the battery is left inside the camera, damage caused by leakage may occur.

• Before you discard the battery, cover the terminals with tape or other insulators.

Contacting other metal materials may lead to fire or explosions.

• Unplug the battery charger from the power outlet after charging is complete, or

when you are not using it.

• Do not place anything, such as cloth on top of the battery charger while it is

charging.

Leaving the unit plugged in for a long period of time may cause it to overheat and distort,

resulting in fire.

• Do not place the battery near pets.

Pets biting the battery could cause leakage, overheating or explosion, resulting in fire or

damage.

• Do not sit down with the camera in your pocket.

Doing so may cause malfunctions or damage the screen.

• When putting the camera in your bag, ensure that hard objects do not come into

contact with the screen.

• Do not attach any hard objects to the camera.

Doing so may cause malfunctions or damage the screen.

7

Checking the Package Contents ...........................................................2

Read This First ......................................................................................3

Safety Precautions.................................................................................4

Attaching the Strap/Holding the Camera ...............................................7

Charging the Battery..............................................................................8

Compatible Memory Cards (Sold Separately) .....................................10

Inserting the Battery and Memory Card...............................................10

Setting the Date and Time ...................................................................13

Setting the Display Language..............................................................15

Formatting Memory Cards ...................................................................16

Pressing the Shutter Button.................................................................17

Taking Pictures (Smart Auto)...............................................................18

Viewing Images ...................................................................................21

Erasing Images....................................................................................22

Shooting Movies ..................................................................................23

Viewing Movies....................................................................................25

Transferring Images to a Computer for Viewing ..................................26

Accessories .........................................................................................31

Separately Sold Accessories ...............................................................32

• Attach the included strap and wrap it around your wrist to avoid dropping

the camera during use.

• Keep your arms tight against your body while holding the camera firmly by

the sides when shooting. Be sure that your fingers do not block the flash.

Table of Contents

Attaching the Strap/Holding the Camera

Strap

8

Use the included charger to charge the battery. Be sure to charge the battery

as it is not charged at the time of purchase.

Remove the cover.

Insert the battery.

z Align the o marks on the battery and

charger, then insert the battery by sliding it

in ( ) and down ( ).

Inserting the Battery and Memory Card

11

Insert the battery.

z Press the battery lock in the direction of the

arrow, then insert the battery as shown

until it locks into place with a click.

z Be sure to insert the battery in the correct

direction or it will not properly lock into

place.

Insert the memory card.

z Insert the memory card as shown until it

locks into place with a click.

z Be sure the memory card is oriented

correctly. Inserting the memory card in the

wrong direction could damage the camera.

Close the cover.

z Close the cover ( ), and press downward

as you slide it until it clicks into place ( ).

Terminals Battery

lock

Terminals

What if [Memory card locked] appears on the screen?

SD, SDHC, SDXC memory cards, and Eye-Fi cards have a write-protect tab. If

this tab is in the locked position, [Memory card locked] will appear on the screen

and you will not be able to take or erase images.

Inserting the Battery and Memory Card

12

Removing the Battery and Memory Card

Remove the battery.

z Open the cover and press the battery lock

in the direction of the arrow.

X The battery will pop up.

Remove the memory card.

z Push the memory card in until you hear a

click, then slowly release it.

X The memory card will pop up.

Number of Shots per Memory Card

• Values are based on the default settings.

• The number of shots that can be taken will vary depending on camera settings, the

subject and the memory card used.

Memory Card

4 GB 16 GB

Number of Shots

Approx. 1231 Approx. 5042

Can you check the number of shots that can be taken?

You can check the number of shots that can be taken when the camera is in a

Shooting mode (p. 18).

Number of shots that can be taken

13

The Date/Time settings screen will appear the first time the camera is turned

on. Since the dates and times recorded into your images are based on these

settings, be sure to set them.

Turn on the camera.

z Press the ON/OFF button.

X The Date/Time screen will appear.

Set the date and time.

z Press the qr buttons to choose an option.

z Press the op buttons to set a value.

Complete the setting.

z Press the m button.

X Once the date and time have been set, the

Date/Time screen will close.

z Pressing the ON/OFF button will turn off

the camera.

Setting the Date and Time

Reappearing Date/Time screen

Set the correct date and time. If you have not set the date and time, the Date/Time

screen will appear each time you turn on the camera.

Daylight saving time settings

If you choose in Step 2 and press the op buttons to choose , you will set

the time to daylight saving (1 hour ahead).

Setting the Date and Time

14

Changing the Date and Time

You can change the current date and time settings.

Display the menu.

z Press the n button.

Choose [Date/Time].

z Move the zoom lever to choose the 3 tab.

z Press the op buttons to choose [Date/

Time], then press the m button.

Change the date and time.

z Follow Steps 2 and 3 on p. 13 to adjust the

setting.

z Press the n button to close the menu.

Date/Time battery

• The camera has a built-in date/time battery (backup battery) that allows the

date/time settings to be retained for about three weeks after the battery pack

has been removed.

• By inserting a charged battery or connecting an AC adapter kit (sold separately,

p. 32) the date/time battery can be charged in about 4 hours even if the camera

is not turned on.

• If the date/time battery is depleted, the Date/Time screen will appear when you

turn the camera on. Follow the steps on p. 13 to set the date and time.

15

You can change the language that displays on the screen.

Enter Playback mode.

z Press the 1 button.

Display the settings screen.

z Press and hold the m button, then

immediately press the n button.

Set the display language.

z Press the opqr buttons to choose a

language, then press the m button.

X Once the display language has been set,

the settings screen will close.

Setting the Display Language

What if the clock appears when the m button is pressed?

The clock will appear if too much time passes between pressing the m button

and the n button in Step 2. If the clock appears, press the m button to

remove the clock and repeat Step 2.

You can also change the display language by pressing the n button

to choose [Language] from the 3 tab.

16

Before you use a new memory card or one that has been formatted in other

devices, you should format the card with this camera. Formatting (initializing) a

memory card erases all data on the memory card. As you cannot retrieve the

erased data, exercise adequate caution before formatting the memory card.

Before formatting an Eye-Fi card (see Camera User Guide), be sure to install

the software contained on the card to a computer.

Display the menu.

z Press the n button.

Choose [Format].

z Move the zoom lever to choose the 3 tab.

z Press the op buttons to choose [Format],

then press the m button.

Choose [OK].

z Press the qr buttons to choose [OK], then

press the m button.

Format the memory card.

z Press the op buttons to choose [OK],

then press the m button.

X The memory card will be formatted.

Formatting Memory Cards

Pressing the Shutter Button

17

Complete formatting.

X When formatting ends, [Memory card

formatting complete] will appear on the

screen.

z Press the m button.

To take images that are in focus, be sure to first press the shutter button

lightly (halfway) to focus, then press fully to shoot.

Press halfway (Press lightly to focus).

z Press lightly until the camera beeps twice

and AF frames appear where the camera

focused.

Press fully (Press fully to shoot).

X

The camera plays the shutter sound and

takes the shot.

z Since the shot is being taken while the

shutter sound plays, be careful not to move

the camera.

Formatting or erasing data on a memory card merely changes the file

management information on the card and does not ensure its contents are

completely erased. Be careful when transferring or disposing of a memory

card. When disposing of a memory card, take precautions such as

physically destroying the card to prevent personal information leaks.

• The total capacity of the memory card displayed in the formatting screen

may be less than indicated on the memory card.

• Perform a low-level format (see Camera User Guide) of the memory card

when the camera does not operate properly, the recording/reading speed

of a memory card has dropped, when continuous shooting speed slows

down, or when movie recording stops suddenly.

Pressing the Shutter Button

Taking Pictures (Smart Auto)

18

Since the camera can determine the subject and shooting conditions, you can

let it automatically select the best settings for the scene and just shoot. The

camera can also detect and focus on faces, setting the color and brightness

to optimal levels.

Turn on the camera.

z Press the ON/OFF button.

X The start-up screen will appear.

Enter A mode.

z Set the mode switch to A.

z When you point the camera toward the

subject, the camera will make a slight

noise as it determines the scene.

X The icon for the determined scene will

appear in the upper right of the screen.

X The camera will focus on detected

subjects and display frames on them.

Does the length of the shutter sound change?

• Since the time required to shoot differs depending on the scene you want to

take, the length of the shutter sound may change.

• If the camera or subject moves while the shutter sound is playing, the recorded

image may be blurry.

If you shoot without pressing the shutter button halfway, the image may not

be in focus.

Taking Pictures (Smart Auto)

19

Compose the shot.

z Moving the zoom lever toward i

(telephoto) will zoom in on your subject,

making it appear larger. Moving the lever

toward j (wide angle) will zoom out from

your subject, making it appear smaller.

(The zoom bar showing the zoom position

appears on the screen.)

Focus.

z Press the shutter button halfway to focus.

X When the camera focuses, it will beep

twice and AF frames will appear where the

camera focused.

Several AF frames will appear when the

camera focuses on more than one point.

Shoot.

z Press the shutter button fully to shoot.

X The camera will play the shutter sound and

shoot. The flash will automatically fire in

low light conditions.

X The image will appear on the screen for

approximately two seconds.

z You can take a second picture even while

an image is displayed by pressing the

shutter button again.

Zoom bar

AF Frame

Taking Pictures (Smart Auto)

20

What if...

• What if the color and brightness of the images do not turn out as

expected?

The scene icon (see Camera User Guide) that appears on the screen may not

match the actual scene. If this happens, try shooting in G mode (see Camera

User Guide).

• What if white and gray frames appear when you point the camera toward

a subject?

A white frame appears on the face or subject that the camera detected as the

main subject, while gray frames appear on other detected faces. The frames will

follow the subjects within a certain range.

If the subject moves, however, the gray frames will disappear, leaving only the

white frame.

• What if a frame does not appear on the subject you want to shoot?

The subject may not be detected, and frames may appear on the background.

If this happens, try shooting in G mode (see Camera User Guide).

• What if a blue frame appears when you press the shutter button halfway?

A blue frame appears when a moving subject is detected; the focus and

exposure will continuously adjust (Servo AF).

• What if a flashing appears?

Attach the camera to a tripod so that the camera does not move and blur the image.

• What if the camera does not play any sounds?

Pressing the p button while turning on the camera power will turn off all sounds.

To turn the sounds on, press the n button to choose [Mute] from the 3

tab, then press the qr buttons to choose [Off].

• What if the image comes out dark even if the flash fired when shooting?

The subject is too far away for the flash to reach. The effective flash range is

approximately 30 cm – 4.0 m (12 in. – 13 ft.) from the end of the lens at

maximum wide angle (j), and approximately 50 cm – 2.0 m (1.6 – 6.6 ft.) from

the end of the lens at maximum telephoto (i).

• What if the camera beeps once when the shutter button is pressed

halfway?

Your subject may be too close. When the camera is at maximum wide angle (

j

),

move about 3 cm (1.2 in.) or more away from your subject and shoot. Move about

50 cm (1.6 ft.) or more away when the camera is at maximum telephoto (

i

).

• What if the lamp lights when the shutter button is pressed halfway?

To reduce red-eye and to assist in focusing, the lamp may light when shooting

in dark areas.

• What if the h icon blinks when you try to shoot?

The flash is charging. You can shoot when recharging ends.

Viewing Images

21

You can view the images you have taken on the screen.

Enter Playback mode.

z Press the 1 button.

X The last image you took will appear.

Choose an image.

z Pressing the q button will cycle through

the images from newest to oldest.

z Pressing the r button will cycle through

the images from oldest to newest.

z Pressing and holding the qr buttons will

display images in a line letting you quickly

search them. Pressing the m button

restores single image playback (see

Camera User Guide).

z The lens will retract after approximately 1

minute elapses.

z Pressing the 1 button again while the

lens is retracted will turn off the power.

What if an icon appears in the upper right of the screen?

The icon for the determined scene will appear in the upper right of the screen. For

details on the icons that appear, see “Scene Icons” (see Camera User Guide).

Choosing the subject to focus on (Tracking AF)

After pressing the o button and displaying , point the camera so that is

on the subject you want to focus on. Press and hold the shutter button halfway to

display a blue frame where focus and exposure will be maintained (Servo AF).

Press the shutter button fully to shoot.

Viewing Images

Switching to Shooting mode

Pressing the shutter button halfway while in Playback mode switches the camera

to Shooting mode.

La page charge ...

Canon IXUS 115 HS Manuel utilisateur

Canon IXUS 115 HS Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents