Velleman HAA2801 Guide d'installation

Marque: Velleman

Modèle: HAA2801

Catégorie: Pavés numériques

Taper: Guide d'installation

HAA2801

Programming & Installation Manual

FOR ELECTRIC LOCK, INTER-LOCK

AND SECURITY SYSTEM INSTALLATIONS

SPLIT-DECODED CONTROLLER

FOR HAA28XX SERIES SECURITY KEYPADS

VERSION: 11/2012

TABLE OF CONTENTS

INTRODUCTION

FEATURES

SPECIFICATIONS

PACKAGE CONTENTS

THE SPLIT-DECODED CONTROLLER UNIT (Figure 1)

THE MAIN CIRCUIT BOARD OF THE CONTROLLER --- (Figure 2)

INSTALLATION

Precautions

Split-Decoded Mode -- (For HAA2800 & HAA2801)

The Necessary Connections For Split-Decoded

The Function Mode Jumper Setting For Split-Decoded -- (HAA2800 Only)

The Link-Up Jumper & Link-Up Code Acquisition

The Function Mode Jumper -- (Available On HAA2800 Only)

CONNECTION TERMINALS

The Audible & Visible Signals

The Alarm Outputs & Warnings

RF Remote Controller -- (HAA2800 Only)

Stand Alone Mode -- (HAA2800 Only)

APPLICATION EXAMPLES

Basic Wirings of A Split-Decoded Door Lock

Basic Wirings of An Inter-Lock System Using Two Split-Decoded Keypads

APPLICATION HINTS FOR THE AUXILIARY TERMINALS

PROGRAMMING FOR FULL FEATURES --- (Supplementary Information)

Set System in Programming Mode with The Master Code

Direct Access to Programming Mode with The “DAP” Code – 8 0 8 0

Refresh The System with The “Refreshing Code” --- 9 9 9 9

The Default Values of The Keypad

FEATURE PROGRAMMING -- KEY IN AND STORE THE DESIRED VALUES

Programming Criteria for Codes

Record A Master Code

Record A Super User PIN

Operation And Functions of The Super User PIN

Record The Common User PINs for Output 1, 2 & 3

Record-Delete PINs or Cards for Output 1, 2, & 3

Examples – Programming And Operation

Visitor Codes (For Output 1 Only)

Duress Codes (For Outputs 1, 2 & 3)

The Operation And Function of The Duress Code

Conguration of The Output Modes for Output 1, 2 And 3

Personal Safety And System Lock-Out

...................................................................................

........................................................................................

.................................................................................

.............................................................................

...............................................

....................................6

....................................................................................

......................................................................................

...................................................

.....................................................

..............................8

....................................................8

..........................................9

.......................................................................

....................................................................

...................................................................

..........................................................

.............................................................

.......................................................................

.......................................................

...........................

..........................................

...........................

..........................................

................................

........................................

...............................................................

.........................

..................................................................

..........................................................................

.......................................................................

..................................................

...............................................

..................................................

.......................................................

................................................................

............................................................

.................................................

...........................................

............................................................

User PIN Entry Mode

Pacier Tones On-Off Selection

Output Operation Announcer

Status LED Flashing On-Off during Standby

Door Forced Open Warning & Timing

Door Propped-Up Warning & The Delay Time

Intelligent Egress Button – An Unique Feature of A Contemporary Keypad

Where And Why “Going Out” Needs Attention

Egress Delay, Warning And Alarm

Congurations of The Egress Warning And Alarm

Door Opening Alarm & Timer

Close The Programming Mode

The Operation Modes and The Wiegand Output

Wiegand Output at Keypad Operation Mode

PROGRAMMING SUMMARY CHART --- (Supplementary Information)

............................................................................

..................................................................

.....................................................................

.......................................................

.............................................................35

.....................................................

...........................

...................................................

...............................................................

...............................................

.....................................................................

...................................................................

...................................................

....................................................

..............................

INTRODUCTION

The HAA2801 is a self-contained access controller. It has been designed mainly as the decoder

unit working together with the HAA2866 and HAA2890 keypads to make up a split-decoded keypad

system.

In split-decoded operation the system provides full Tri-Tech features of accepting EM Card, PIN/Code

and RF Remote Control. This unique design philosophy makes the system to provide high level of

security in preventing sabotage far ahead of the traditional stand alone keypad systems.

Note: This manual describes both HAA2800 and HAA2801, but only HAA2801 is supported.

Please disregard all information regarding HAA2800 (stand-alone mode without keypad, RF remote

controller use).

HAA2801 is the simplied version. It is solely a full feature decoder of the HAA28xx series keypad in

Split-decoded operation.

The HAA2801 has three output relays and a built-in door chime. It is an ideal device for Door Strike,

Alarm Arm-disarm control and actuation of Automatic Operator, such as garage door opener.

The keypad system with the HAA2801 decoder in Split-decoded operation offers full features

performance even the keypad is just a simplied version. Maximum three keypads can be connected

in parallel to the decoder unit with one of them setting in master mode and the other two setting in

slave mode. Each keypad can be programmed with its own PINs and Cards. The slave keypads take

the features and the functions programmed in the master keypad to operate the system. The decoder

interprets the data and operates the desired functions faithfully.

For more info concerning this product and the latest version of this manual, please visit our

website www.velleman.eu. The information in this manual is subject to change without prior

notice.

FEATURES

HAA2800 – Full Feature Decoder + RF Remote Control

HAA2801 – Full Feature Decoder

I) HAA2800 & HAA2801

• A Decoder for The HAA28xx Series Keypads in Split-decoded Operation

• Decodes The Data of EM Cards, PINs / Codes & Functions Faithfully from Keypads

• Provides Full Features in Split-Decoded Mode for Any Keypad in The HAA28xx Series

• Simple Three Wires Connection to Keypads For Data Communication, (+), (

) & Data I/O

• Easily to Set Up Link Up Code with The Keypads And The Decoder

• Three Independently Controlled Output Relays

• Built-in Door Chime

• Built-in Alarm for Tamper, Door Forced Open and Door Opening in Split-Decoder Mode

• Built-in Current Limited (750mA) Power Source for The Keypads to Prevent Sabotage of Short

Circuit from Outside

II) HAA2800 Only

• Provides The Tri-Tech Features of RF Remote Control, Card and PIN/Code Reading in One

System

• 24 bits Self-learning Codes (over 1 million codes) for The RF Remote Control Keys

• Accepts 40 RF Remote Control Keys Maximum

• 4 RF Remote Control Channels for Stand Alone or Split-decoded Operation

• Remote Control Key Controls Output 1, 2, 3 & Door Chime

User manual only available in English. Mode d’emploi disponible uniquement en anglais.

SPECIFICATIONS

Operating Voltage:

12V-24V DC, Auto Adjusting

Operating Current:

65mA (quiescent) to 100mA (three relays active)

Operating Temperature:

-20 C to +70 C

Environmental Humidity:

5-95% relative humidity non-condensing

The Adjustable Timer for Output 1:

1-30 Seconds

Power Up Delay:

5 Seconds

Tamper Alarm:

3 Minutes

Input Sensing Terminals:

a) Door position, b) Egress, c) O/P 1 Inhibit, d) Door Bell, e) Tamper

Output Control Terminals:

a) Duress, b) Alarm, c) Key Active, d) Inter-lock;

Transistor Open Collector, 24VDC/100mA sink Max

Output Contact Ratings:

Output Relay 1 – N.C. & N.O. dry contacts, 5A/24VDC Max.

Output Relay 2 – N.C. & N.O. dry contacts, 1A/24VDC Max.

Output Relay 3 – N.C. & N.O. dry contacts, 1A/24VDC Max.

Dimensions:

32.5(H) X 120(W) X 87(D)mm Plastic Box

Weight:

250g net

RF Remote Controller (HAA2800 Only) :

Number of Self-leaning Codes : Over 1 Million

Number of RF Control Keys : 40 Maximum

4 Control Channels : Output 1, 2, 3 & Door Chime

Operation Frequency : 433MHz

Control Distance : 60 Meters Approx. in Open Space

Receiver Type : Super-heterodyne

Operation Voltage : 12V Alkaline Battery, Type 27A (Battery Not Included)

Weight : 32g

Specications are subject to change for modication without notice

PACKAGE CONTENTS

• One Access Controller

• One Pack of Mounting Screws

• Two RF Remote Control Keyfobs (HAA2800 Only), Battery Not Included

• One Owner’s Manual

THE SPLIT-DECODED CONTROLLER UNIT (Figure 1)

THE MAIN CIRCUIT BOARD OF THE CONTROLLER --- (Figure 2)

NOTE:

Factory suggest that the work of timer adjustment and change of jumper settings on the

main circuit board are to be done by the Installer only.No adjustment/setting change is required for

Split-decoded operation with the ex-factory settings.

LINK-UP

JUMPER

OFF-->ON--

>OFF

CODE

LEARNING

BUTTON

(

HAA2800 ONLY

)

REMOTE

CONTROL

SIGNAL &

STATUS

(

HAA2800 ONLY

)

INTERNAL

SIREN

& DOOR CHIME

CONNECTION

TERMINALS

MAINS

OUTPUT BEEP

JUMPER ON OR

OFF

FUNCTION MODE

JUMPER

1. SPLIT-DECODED

2. STAND ALONE

MODE 1

3. STAND ALONE

MODE 2

ADJUSTABLE TIMER

FOR OUTPUT 1

TURN CLOCKWISE

FOR MAXIMUM TIME

RECEIVER FOR

REMOTE CONTROL

(HAA2800 ONLY)

INSTALLATION

PRECAUTIONS

1) Installation Location:

The built-in receiver of the Access Controller is working at the UHF frequency band of 433Mhz. To

get the best receiving result of the signals from the remote keys a correct installation location is

necessary.

i) Install it on a location inside the house facing to the open space and there has no strong electro-

magnetic wave signals near it.

ii) Do not install it in a concrete room or under a concrete stair, which shortens the control distance.

2) Prevent Accidental Short Circuit:

In the previous experience, most of the damages caused in the installation are accidental touching

of the components on circuit board with the wires carrying power. Please be patient in the

installation. Study the manual to become familiar with the specications of the system beforehand is

also important.

i) Do not apply power to the system while it is in installation.

ii) Check carefully all the wirings are correct before applying power to the system for testing.

SPLIT-DECODED MODE -- (for HAA2800 & HAA2801)

Split-decoded Mode needs at least one keypad to work with the decoder. The decoder decodes all the

commands from the keypad to operate its outputs. It is an unique solution to immediately up-grade

a general purpose keypad to a high security access control system. All the keypads in the HAA28xx

Series with Data I/O Port are compatible with the decoder. A Split-decoded system divides itself into

the outside keypad unit and the inside decoder unit. Any sabotage to the outside unit does not affect

the security of the inside unit.

RF WIRELESS

REMOTE CONTROL (DA-2800 ONLY)

DOOR LOCK

(OUTPUT 1)

SECURITY

SYSTEM (OUTPUT 2)

AUTOMATIC

OPERATOR (OUTPUT 3)

COMMON

GROUND

COMMON

GROUND

DA-2800 OR DA-2801

SLAVE 1

SLAVE 2

MASTER

DATA I/O

COMMON

GROUND

DATA I/O

MAXIMUM 3 KEYPADS CAN BE CONNECTED IN PARALLEL

THE NECESSARY CONNECTIONS FOR SPLIT-DECODED

THE FUNCTION MODE JUMPER SETTING FOR SPLIT-DECODED -- (HAA2800 ONLY)

NOTE: No Function Jumper setting is required for the HAA2801. It is xed in Split-Decoder

mode.

1) Put the “Function Mode Jumper” to position “1” for Split-Decoder. (It is an Ex-factory Setting)

2) Set the “Link-up Jumper” from OFF to ON position to enable the link-up of acquiring the link-up

code from the keypad (same as the Master Code of the keypad).

Remark:

THE LINK-UP JUMPER & LINK-UP CODE ACQUISITION

To acquire the link-up code (same as the Master Code) from the Master keypad for Split-Decoded

operation is necessary. At any time, when you operate a new Master keypad at the rst time it is

necessary to let the decoder unit to know the Master Code of the keypad. Otherwise, the decoder can

not recognize the data from it. If more than one keypads are going to link up with the decoder, all the

keypads are required to have the same Master Code and repeat link-up is not necessary.

The decoder executes Link-up Acquisition Only Once at the moment after setting of the Master

Keypad to exit Programming Mode with

Connect the Data I/O ports of the Decoder (Terminal 4) and the Keypad with wire to link-up the

communication of the two units.

Connect the Keypad PWR terminal of the Decoder (Terminal 3) to the keypad power input terminal,

which supplies power to the keypad unit with current limit protection.

Connect the Common (

) Ground (Terminal 2 or 11) to the (

) ground of the keypad unit to make

up the return path for the data and the power source.

Make all other installation connections to the decoder unit, but not to the keypad unit in Split-

Decoded Mode. The system provides full feature from the decoder unit according to the functions

programmed in the keypad.

The Function Jumper of the HAA2800 has been put on Position 1 at the factory. Setting of the

jumper is usually not necessary unless it has been changed. Always put jumper on position “1”

for Split-decoded mode.

The Function Jumper is located on the Main Circuit Board inside the box. Change the setting for

Stand Alone mode is required. See Figure 2.

The Jumper is located on the main circuit board inside the terminal compartment. See Figure1.

The Decoder executes link-up Only Once. The Link-up execution is done when the keypad exits

from Programming Mode after pressing

. Put the jumper back to OFF position after link up.

After the decoder knows the link-up code (Master Code) of the keypad it is not necessary to

repeat the link-up procedure in feature change programming except change of the Master Code.

All the keypads going to link up with the decoder MUST be with the same Master Code which is

the authorization code to enable the data communication between the keypads and the decoder.

It is not necessary to repeat the link-up procedures for the slave keypads with the same Master

Code. Just simply connect them in parallel with the master keypad.

The decoder will refuse other keypads that are not in the same Master Code to link up with it.

The failed keypads in the link-up will generate warning beeps.

Example – Change of the Link-up Code ( The Master Code of the Master Keypad)

a) Put the Link-up Jumper of the Decoder from OFF to ON

OFF ON

b) Set the Master Keypad to Programming Mode

EXISTING MASTER CODE

c) Set a New Master Code to the Master Keypad

NEW MASTER CODE #

d) Set the Master Keypad to exit from Programming Mode

e) The Link-up in the system is done automatically

BEEP BEEP ----- From Keypad

f) Put the Jumper back to OFF

ON OFF

g) The system is in Split-decoded operation with the new Link-up Code

THE FUNCTION MODE JUMPER -- (AVAILABLE ON HAA2800 ONLY)

Three positions are available for the Function Mode Jumper. Position 1 is for Split-decoded Mode and

the positions 2 & 3 are for Stand Alone Modes.

POSITION 1 – SPLIT-DECODER (MAINS LED LAMP FLASHING)

Position 1 is for Split-decoder mode. All the functions and the 3 output relay operation manners follow

the programmed settings in the Master keypad. All the functions of the decoder are programmable

from the keypad unit. The HAA2800 system is controlled by the keypads and the remote control keys

in the Split-decoded mode.

POSITION 2 – STAND ALONE MODE 1 – START / STOP FOR OUTPUT 1 (MAINS LED LAMP ON)

Position 2 is one of the settings for Stand Alone mode. All the three Output Relays are controlled by

the RF Remote Key with the following functions:

Output 1 – Start / Stop –

Output 2 – Start / Stop –

Output 3 – Manual Momentary –

POSITION 3 – STAND ALONE MODE 2 – ADJUSTABLE TIMER FOR OUTPUT 1 (MAINS LED

LAMP ON)

Position 3 is one of the settings for Stand Alone mode. All the three Output Relays are controlled by

the RF Remote Key with the following functions:

Output 1 – Adjustable Timer –

Output 2 – Start / Stop –––––––

Output 3 – Manual Momentary –

Controlled by Channel 1 of the RF remote key. Press the Button A once to

start and press the button once again to stop.

Controlled by Channel 2 of the RF remote key. Press the Button B once to

start and press the button once again to stop.

Controlled by Channel 3 of the RF remote key. The output relay

operates (Starts) as long as the Button C is pressed and it stops

when the button is released.

Controlled by Channel 1 of the RF remote key. Press the Button A

once to start the timer and it resets automatically after time out. It is

adjustable 1-30 seconds. It is convenient for setting the time for door

strike. Turn the timer clockwise for maximum time. See Figure 2.

Controlled by Channel 2 of the RF remote key. Press the Button B

once to start and press the button once again to stop.

Controlled by Channel 3 of the RF remote key. The output relay

operates (Starts) as long as the Button C on the remote key is

pressed and it stops when the button is released.

CONNECTION TERMINALS

NOTE:

DRY CONTACT

A dry contact means that no electricity is connected to it. It is prepared for free connections.

N.C.

Normally Closed, the contact is closed circuit at normal state. It is open circuit when active.

N.O.

Normally Open, the contact is open circuit at normal state. It is closed circuit when active.

TRANSISTOR OPEN COLLECTOR OUTPUT

An open collector output is equivalent to a Normally Open (N.O.) contact referring to ground similar

to a relay contact referring to ground. The transistor is normally OFF, and its output switches to

ground (

) when active. The open collector can only provide switching function for small power but

it is usually good enough for controlling of an alarm system. The maximum rating is 24V DC/100mA

Sink

OPEN COLLECTOR

OUTPUT ----

Output switches to

ground when activated

N.O. CONTACT

OUTPUT ----

Output switches to

ground when activated

EQUIVALENT

ALARM O/P

KEY ACT O/P

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

TAMPER

GND(

)

DOOR SENS

O/P 1 INHIB

INT. LOCK

DU OUT

DOOR BELL IN

EG IN

DATA I/O

KEYPAD PWR

GND(

)

12-24V DC

OPEN COLLECTOR OUTPUT

1A RELAY DRY CONTACTS

FOR AUXILIARY CONTROL

1A RELAY DRY CONTACTS

FOR AUXILIARY CONTROL

5A RELAY DRY CONTACTS

FOR DOOR STRIKE

OPEN COLLECTOR OUTPUT

INPUT/OUTPUT FOR SPLIT-DECODED SIGNALS

POWER OUTPUT FOR KEYPADS

COMMON GROUND

POWER INPUT FOR SYSTEM

N.C. SW

COMMON GROUND

N.C. SW

N.O. SW

OUTPUT 1O UTPUT 2O UTPUT 3

1 - 2 : 12-24V DC I/P -- (Power Input Terminal)

Connect to a 12-24V DC power supply. The (

) supply and the (

) GND are the common grounding

points of the system. The system accepts full input voltage range.

3 : KEYPAD POWER O/P -- (Power Output for External Keypads – 500mA Max.)

This power source is prepared for the external keypad(s). Its output voltage follows to the input

voltage at terminals 1 - 2 but the output current is limited to 500mA only. This output terminal is

protected by a 500mA reset-able fuse to prevent sabotage to the internal power supply of the

system with short circuit from the external keypad.

4 : DATA I/O PORT -- (Data Input/Output Port for Split-Decoded Operation)

Connect this terminal with the Data I/O wire from the wire harness on the keypad unit to link up

system for Split-Decoded operation. Maximum 3 keypads can be connected in parallel to this

terminal.

Note:

Leave this terminal open if the controller is in Stand Alone operation. (Stand Alone operation is one

of the operation modes of the HAA2800)

5 : EG IN -- ( Egress Input)

A Normally Open (N.O.) input terminal referring to (

) ground. With the help of a normally open

button to activate Output 1 for door open in the same manner of using the User PINs or Cards

on keypad in Split-decoded mode; OR follows the Function Mode jumper setting of Start/Stop or

Momentary in Stand Alone mode.

Egress button is usually put inside the house near the door for exit convenience. More than one

egress buttons can be connected in parallel to this terminal. Leave this terminal open if not used.

6 : DOOR BELL I/P -- (Door Bell Button Input)

A terminal prepared for the connection of a normally open (N.O.) button referring to (

) ground to

activate the built-in door chime. More than one door bell buttons can be connected in parallel to this

terminal. Leave this terminal open if not used.

7 : DU OUT -- (Duress Output) – Available on Split-decoded Mode Only

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It

is equivalent to an N.O. (Normally Open) terminal switching to (

) ground after the entry of Duress

Code. Use it to trigger an alarm zone of a security system, or turn on a buzzer to notify a guard.

Please see the application hints for more information.

Duress Function is available only on Split-decoded mode with Duress Code programmed from

keypad.

8 : INTER-LOCK O/P -- (Inter-lock Control Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It is

OFF at normal condition. It switches to (

) ground immediately for the rst 5 seconds after received

an operation command for Output 1 or after keying in a valid User PIN or reading a Card to operate

Output 1. It keeps tying to (

) ground during the Door Position Sensor is open circuit due to door

open. Use this output point to make cross wire connection with the associated controller’s “O/P 1

Inhibit” point in an Inter-lock system to prevent both doors that can be opened at the same time.

An Inter-lock System:

An inter-lock system is a two-door system that always allows only one of the doors to open during

the operation. While one of the doors is opened, the other door keeps close until the open door is

re-closed. It prevents the unauthorized people dashing into a protected area.

An inter-lock system needs two keypads or controllers and two door position sensing switches for

the two doors. Please see the Application Example for more information

9 : O/P 1 INHIBIT -- (Output 1 Inhibit Control Input – Normally Open)

A Normally Open (N.O.) sensing input point for controlling of the Output 1, with this terminal

connecting to (

) ground, the Egress Button and the whole group of Users (PINs & Cards) for

Output 1 are disabled. It is prepared mainly for the cross wire connection with the “Inter-lock O/P”

point on the associated controller in an Inter-lock system. The inhibit function also governs the RF

remote control key from operating of the Output 1 (if the decoder is HAA2800).

10 : DOOR SENS N.C. -- (Door Position Sensing Input -- Normally Close)

A Normally Closed (N.C.) sensing point referring to (

) ground, with the help of a normally closed

magnetic contact monitors the open or close state of the door. It initiates the following functions for

the system. Connect it with jumper to (

) Ground if not used.

a) Door Auto Re-lock

The system immediately re-locks the door after it is re-closed before the end of the programmed

time for output 1. It prevents unwanted “tailgate” entry.

b) Door Forced Open Warning (available in Split-decoded Mode only)

The controller generates “door forced open” warning and triggers alarm output instantly once

the door is forced to open without using a valid user PIN, Card or pressing of egress button. The

warning lasts as long as the time programmed (1-999 seconds). It can be stopped with the User

PIN or card for output 1 at anytime. See programming Location 80 of the keypad for the details.

c) Door Propped-up Warning (available in Split-decoded Mode only)

The controller generates propped-up warning beeps (does not activates alarm output) while the

door is left open longer than the allowable time programmed. The warning will last as long as the

door is open until it is re-closed. See programming Location 81 of the keypad for the details.

d) Inter-lock Control

The inter-lock control output always goes to (

) while the door is open, which gives signal to

disable the associated controller in the inter-lock system. See the Inter-lock terminal description

for more information.

e) Door Opening Alarm (available in Split-decoded Mode only)

Door Opening Alarm is designed for the emergency door only. It is always given when the door is

opened unless a valid User Code or Card is used prior to the door is opened. See programming

Location 91 of the keypad for the details.

11 : (

) GND -- (Common Ground of The System)

A grounding point of the keypad that is common to terminal 2.

12 : TAMPER IN -- (Tamper Switch – Normally Closed Input Terminal)

A Normally Closed (N.C.) input terminal referring to (

) ground. It is prepared for the tamper switch

of the keypad connecting to it. When the tamper switch is open circuit it triggers the internal siren

and the Alarm Output terminal. Link up this terminal to (

) Ground with jumper if not used.

The alarm lasts for 3 minute in stand alone mode. It is reset-able before expiry with User Code from

keypad in Split-decoded mode.

13 - 14 - 15 : OUTPUT 1 -- (Output Relay 1)

5 Amp relay dry contact controlled by the Group 1 User PINs & Cards in Split-decoded mode or by

the RF remote key in Stand Alone mode. It is recommended for door strike. Terminal 13 is Normally

Closed contact (N.C.), terminal 15 is Normally Open contact (N.O.) and terminal 14 is the common

point of the two contacts. Use N.C. output for Fail-safe locking device; and N.O. output for Fail-

secure locking device.

(a) The operation of Output 1 is programmable from the keypad in Split-decoded operation (with

Function Jumper on position 1). See programming Location 51 of the keypad for the details.

(b) The Output 1 is selectable for Start/Stop (toggle) mode (with Function Jumper on position 2) or

Adjustable Momentary Timer mode (with Function Jumper on position 3) in Stand Alone mode.

The Adjustable Timer (1-30 seconds) is located on the main circuit board inside the box. See Figure 2.

16 - 17 - 18 : OUTPUT 2 -- (Output Relay 2)

1 Amp relay dry contact controlled by the Group 2 User PINs & Cards in Split-decoded mode or by

the RF remote key in Stand Alone mode. It is an auxiliary output ideally for controlling of security

system or automatic operator. Terminal 16 is Normally Closed contact (N.C.), terminal 18 is Normally

Open contact (N.O.) and terminal 17 is the common point of the two contacts.

(a) The operation of Output 2 is programmable from the keypad in Split-decoded operation (with

Function Jumper on position 1). See programming Location 52 of the keypad for the details.

(b) The Output 2 is always xed on Start/Stop (toggle) operation with Function Jumper on position 2

or 3 in Stand Alone mode.

19 - 20 - 21 : OUTPUT 3 -- (Output Relay 3)

1 Amp relay dry contact controlled by the Group 3 User PINs & Cards in Split-decoded mode or by

the RF remote key in Stand Alone mode. It is an auxiliary output ideally for controlling of security

system or automatic operator. Terminal 19 is Normally Closed contact (N.C.), terminal 21 is Normally

Open contact (N.O.) and terminal 20 is the common point of the two contacts.

(a) The operation of Output 3 is programmable from the keypad in Split-decoded operation (with

Function Jumper on position 1). See programming Location 53 of the keypad for the details.

(b) The Output 3 is always xed on Manual Momentary operation with Function Jumper on position

2 or 3 in Stand Alone mode. Manual Momentary means that the relay output works as long as

the button of the RF remote key is pressed. The relay output is released when the key button is

released.

22 : KEY ACT O/P -- (Keypad Active Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It

is equivalent to an N.O. (Normally Open) terminal referring to ground. It switches to (

) ground for

10 seconds on each key touch on the keypad or receiving of a command signal from the RF remote

key. It can be used to drive a small power device, such as a relay or a low power control point of

other equipment. See the Application Hints for more information.

23 : ALARM O/P -- (Alarm Output)

An NPN transistor open collector output with the maximum power rating of 24VDC/100mA sink. It is

equivalent to an N.O. (Normally Open) terminal referring to ground. It switches to (

) ground while

alarm occurs in order to trigger an external alarm to give notication at remote location. Use it to

drive a small power device, such as a relay or a low power control point of other equipment.

The Alarm Output for tamper is 3 minutes xed. Other alarm outputs are programmable in Split-

decoded operation.

THE OUTPUT BEEP JUMPER

The controller gives beep sound when the relay output activates in stand alone mode or when

a command signal from the RF remote key is received. The beep jumper has been put on the

ON position at the factory. It can be stopped for silent environment by putting the jumper to OFF

position. The Jumper is located on the main circuit board. See Figure 2.

THE AUDIBLE AND VISIBLE SIGNALS

STATUS AUDIBLE SIGNALS MAINS LED SIGNALS

1) Power-up Delay (5 Seconds) Continuous Beeps Continuous Fast Flashes

2) Power-up Delay (1 Minute)* Continuous Beeps Continuous Fast Flashes

3) System In Standby Mode OFF 1 Flash / Second

4) System In Standby Mode* OFF ON

5) Keypad In Programming Mode OFF 1 Flash / Second

6) Successful Command from RF Key 2 Beeps 2 Flashes

7) Output Relay Active (From Keypad) 1 Long Beep or 2 Short Beeps No Signal

8) Egress Delay Warning Fast Beeps Nil

9) Door Forced Open Warning Fast Beeps + Alarm Output Nil

10) Door Propped-up Warning Fast Beeps Only Nil

11) Alarm Output Warble Tone Siren Nil

12) Door Chime Dual Tone Door Chime Nil

* Stand Alone Mode

THE ALARM OUTPUTS & WARNINGS

1) Tamper Alarm:

a) The alarm is triggered via the “Tamper In” terminal

b) Alarm Output and Internal Siren activate

c) The alarm period is xed in 3 minutes for Stand Alone Mode

d) It can be reset with Super User Code # 1 or an user Code/Card in Group 1 in Split-decoded

Mode

The Following Alarm & Warning Are Available in Split-decoded Operation Mode Only

2) Egress Delay Alarm:

a) The Egress Delay Alarm is enabled by programming from keypad at Programming Location 90

b) The alarm activates during the Egress Delay period and it stops at the expiry of the Egress Delay

c) Alarm Output and Internal Siren activate

3) Egress Delay Warning:

a) The Egress Delay Warning is enabled by programming from keypad at Programming Location 90

b) The warning activates during the Egress Delay period and it stops at the expiry of the Egress Delay

c) The warning beep is given by the internal buzzer only

4) Door Open Alarm (Designed for Emergency Door):

a) The Door Open Alarm is enabled by programming from keypad at Programming Location 91

b) Alarm Output and Internal Siren activate

c) Alarm happens in door forced to open or normal open with Egress Button

d) No Alarm happens in door open with User PIN or Card

5) Door Forced Open Alarm:

a) The Door Forced Open Alarm is enabled by programming from keypad at Programming Location 80

b) Alarm Output and Internal Siren activate

c) Alarm happens in door forced to open only

d) No Alarm happens in door open with Egress Button, User PIN or Card

Note: If both alarms (4) & (5) are enabled in the programming, the system will take the longer one for

alarm time.

6) Door Propped-up Warning

a) The Door Propped-up Warning is enabled by programming from keypad at Programming Location 81

b) The warning starts at the expiry of the propped-up delay.

c) The warning beep is given by the internal buzzer only

RF REMOTE CONTROLLER -- (HAA2800 ONLY)

The HAA2800 RF Remote Controller consists of a built-in receiver and two remote control keys, which

has 4 channels to control the Output Relay 1, 2, 3 and the built-in door chime. Two remote keys are

supplied and up to 40 remote keys can be accommodated by the system. The receiver (decoder) of

the system learns the ID codes from the remote keys. Each remote key contains a 24-bit ID code

that provides over 1 million code combinations. The remote key gives around 60 Meters of controlling

distance in open space to the receiver.

(A) Procedure of Recording An RF Remote Key -- (Learning)

The RF remote keys that prepare to work with the decoder are required to be registered. The decoder

learns the ID of the remote keys one by one beforehand with the following procedures:

(B) Procedure of Deleting The RF Remote Keys from Memory -- (Clearing)

If an RF remote key is lost it is necessary to delete it from the memory of the receiver. Every time the

system will clear all the ID Codes of the RF Remote Keys in the deletion. Re-learn the existing remote

keys are necessary.

The system can be operated with the RF Remote Control Keys no matter it is in Split-decoded Mode

or in Standard Alone Mode. In the Split-decoded mode, the RF Remote Key operates the system

according to the functions and data that have been programmed with the digital keypad. While in Stand

Alone operation the system operates its outputs according to the functions that stated in the Stand

Alone Mode 1 or Mode 2.

1) Press button A to operate Output 1

2) Press button B to operate Output 2

3) Press button C to operate Output 3

4) Press button D to operate the built-in Door Chime

STAND ALONE MODE -- (HAA2800 ONLY)

The system that operates in Stand Alone mode does not require the keypad. It is directly controlled by

the RF Remote Key for the outputs. It is an ideal solution for the remote controls of door strike, alarm

arm-disarm, garage door opening etc.. The following settings are necessary while the system is in

stand alone operation:

Press and hold the LEARN button on the receiver unit for 1 second until the REMOTE LED turns

ON. (The button is inside the hole. Use a pin or the tip of a ball pen to reach it). See Figure 1

The decoder of the receiver is in Waiting Mode for 10 seconds waiting for the signal from the

Remote Key after the Remote LED turning ON.

Press any button of the RF Remote Key unit ONCE within the 10 seconds for the receiver to learn

the ID Code from it.

The REMOTE LED on the receiver unit turns OFF after the ID Code is learned.

Take the above learning procedures 1-4 for other RF Remote Keys

Press and hold the LEARN button on the receiver unit for 8 seconds (Remote LED turns ON) until

the REMOTE LED gives 2 ashes to conrm that all the data are erased. Then the LED turns

OFF.

Record the ID Code of the existing RF Remote Keys (not lost) into the memory again one by one

with the procedures stated in the “Recording An RF Remote Key”

Put the “Function Mode Jumper” to position “2” or “3” for the desired Stand Alone Operation

Mode. See the “Function Mode Jumper Setting” stated above for the details.

Always put “Link-up Jumper” on OFF position.

Leave the “Data I/O” port open without any connection.

Make all the installation connections to the terminals of the decoder unit.

APPLICATION EXAMPLES

1) BASIC WIRINGS OF A SPLIT-DECODED DOOR LOCK

NOTE:

• Connect the 1N4004 as close as possible to the lock in parallel with the lock power terminals of the

lock to absorb the back EMF to prevent it from damaging the keypad. The 1N4004 is not required if

the electric lock is AC operated.

• To avoid Electro-Static-Discharge from interfering with the operation of the keypad, always ground

the (

) terminal of the keypad to earth.

• Always connect DOOR SENSOR terminal to (

) ground if not used.

• Always connect TAMPER terminal to (

) ground if not used.

• Make 3-wire Connection (+,

, DATA I/O) to the keypad in the HAA28xx Series. More than one

keypads can be connected in parallel.

ALARM O/P

KEY ACT O/P

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

TAMPER

GND(

)

DOOR SENS

O/P 1 INHIB

INT. LOCK

DU OUT

DOOR BELL IN

EG IN

DATA I/O

KEYPAD PWR

GND(

)

12-24V DC

N.O.

ELECTRIC LOCK

1N4004

CATHODE

OUTPUT RELAY 1

N.O. Output for Fail-secure Lock

N.C. Output for Fail-safe Lock

N.C.

OUTPUT 1 OUTPUT 2 OUTPUT 3

DIGITAL KEYPAD

AD-1312 OR AP-960

EGRESS BUTTON

MORE EGRESS

BUTTON CAN

BE CONNECTED

IN PARALLEL

DOOR BELL

BUTTON

N.O.

(

)

(

)

(

)

N.O.

2) BASIC WIRINGS OF AN INTER-LOCK SYSTEM USING TWO SPLIT-DECODED KEYPADS

An inter-lock system needs two door controllers. This application example uses two keypad systems

with simple cross wire connection on their "Output 1 Inhibit" and "Inter-lock Control Output" terminals.

It is necessary to link up the "(

) GND" terminals of the two keypads as common ground to achieve

the inter-lock logical functions.

• Use keypad to open the door from outside

• Press egress button to open the door from inside

• Connect the door magnetic sensors on the doors to monitor their positions

• While door 1 is open, then, door 2 is forced to keep close, or vice versa

• Use N.O. Relay output for fail-secure lock; and N.C. output for fail-safe lock

• Please also see the "NOTE" stated in the Application Example (1)

ALARM O/P

KEY ACT O/P

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

TAMPER

GND(

)

DOOR SENS

O/P 1 INHIB

INT. LOCK

DU OUT

DOOR BELL IN

EG IN

DATA I/O

KEYPAD PWR

GND(

)

12-24V DC

N.O.

ELECTRIC LOCK

1N4004

DOOR 1

OUTPUT RELAY 1

N.O. Output for Fail-secure Lock

N.C. Output for Fail-safe Lock

N.C.

OUTPUT 1 OUTPUT 2 OUTPUT 3

DIGITAL KEYPAD

AD-1312 OR AP-960

EGRESS BUTTON

DOOR BELL

BUTTON

N.O.

(

)

(

)

N.O.

DOOR 1

SENSING

COMMON GROUND

(

)

DA-2800 OR DA-2801 DA-2800 OR DA-2801

CROSS WIRE CONNECTION FOR INTER-LOCK FUNCTIONS

ALARM O/P

KEY ACT O/P

N.O.

COM

N.C.

N.O.

COM

N.C.

N.O.

COM

N.C.

TAMPER

GND(

)

DOOR SENS

O/P 1 INHIB

INT. LOCK

DU OUT

DOOR BELL IN

EG IN

DATA I/O

KEYPAD PWR

GND(

)

12-24V DC

N.O.

ELECTRIC LOCK

1N4004

DOOR 2

OUTPUT RELAY 1

N.O. Output for Fail-secure Lock

N.C. Output for Fail-safe Lock

N.C.

OUTPUT 1 OUTPUT 2 OUTPUT 3

DIGITAL KEYPAD

AD-1312 OR AP-960

EGRESS BUTTON

DOOR BELL

BUTTON

N.O.

(

)

(

)

N.O.

DOOR 2

SENSING

APPLICATION HINTS FOR THE AUXILIARY TERMINALS

The tamper switch is Normally Closed while the

keypad is secured on the gang box. It is open

when the keypad is removed from the gang

box. To get warning at sabotage, connect the

tamper switch to the TAMPER terminal of the

HAA2800. If more than one tamper switches

are connected, just connect them in series.

With the help of a Normally Closed

door position sensor (usually a

magnetic door switch) on the door to

set up the following functions:

Door Auto Relock -- The system will

immediately relock the door after a valid access

has been gained to prevent "tailgate" entries.

Door Forced-open Alarm -- The keypad will

generate alarm instantly if the door is forced to

open. Enable the function at Location 80.

Door Propped-up Alarm -- The keypad will

generate alarm if the door is left open longer

than the pre-set delay time. Enable the function

at Location 81.

Inter-lock Control -- When the door is open,

the interlock output of the keypad will give a (

)

command to stop the other keypad in an inter-

lock system.

Door Opening Alarm -- Door Opening Alarm

is designed for the emergency door only. It is

always given when the door is opened unless a

valid user code or card is used prior to the door

is opened. Enable the function at Location 91.

(A) TAMPER N.C.

(B) DOOR SENS

The Alarm Output switches to (

) ground in door forced to open or the door open after Egress

Delay. You may use it to turn ON an LED lamp and/ or a small buzzer to notify a guard; or

connect it to a 24 hour Normally Open protection zone of an alarm system. See Location 80 and

Location 91 for more information about these functions.

Only one connection option is recommended. Make sure that the sink current does not

exceed the maximum rating of 100mA.

GND(

)

N.C

TAMPER SWITCH

OF THE KEYPAD

GND(

)

DOOR

SENS

ALARM

O/P

KEY ACT

O/P

GND

(

)

ALARM

O/P

KEY ACT

O/P

GND

(

)

The Duress Output switches to (

) ground when duress code is entered. You may use it to turn

ON an LED lamp and/ or a small buzzer to notify a guard; or connect it to a 24 hour Normally

Open protection zone of an alarm system.

Only one connection option is recommended. Make sure that the sink current does not

exceed the maximum rating of 100mA.

(E) DURESS OUTPUT

The Key Active Output switches to (

) ground

for 10 seconds whenever a key is touched.

You may use it to turn ON an LED lamp and

/or a small buzzer to notify a guard; or to

energize a relay to switch ON lights or trigger

an CCTV Camera to start recording.

Make sure that the relay for switching ON

lights has high enough isolation between

high voltage and low voltage to prevent

damage of the keypad.

Only one connection option is recommended.

Make sure the sink current does not exceed

the maximum rating of 100mA.

External power supply and isolation relay

are strictly necessary in driving high power

device, such as lights.

(D) KEY ACTIVE OUTPUT

(a) (b)

GND

(

)

DOOR

SENS

O/P 1

INHIB

INT.

LOCK

OUT

GND

(

)

DOOR

SENS

O/P 1

INHIB

INT.

LOCK

OUT

ALARM

O/P

KEY ACT

O/P

GND

(

)

ALARM

O/P

KEY ACT

O/P

GND

(

)

Use the Normally Open (N.O.) output contact to shunt a Normally Closed (N.C.) protection

zone of an alarm system.

Set output contact to Start / Stop Mode (Programming Option 52, Output Mode=0).

Use the (N.O.) or (N.C.) output contact to make arm-disarm control of an alarm system.

Consult your alarm control panel manual for the appropriate output contact to be used in arm-

disarm control.

Usually set output 2 to Momentary mode (Programming Option 521, Location 52, Output

Mode=1) for multi station systems and Start / Stop mode (Programming Option 520, Location

52, Output Mode=0) for single station systems.

(F) OUTPUT 2 OR OUTPUT 3

( i ) Shunting an N.C. Zone

( ii ) Alarm System Arm-Disarm Control

La page charge ...

Velleman HAA2801 Guide d'installation

Marque: Velleman

Modèle: HAA2801

Catégorie: Pavés numériques

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Velleman HAA2801 Installation guide

Documents connexes

Velleman HAA85WP Manuel utilisateur

Velleman HAA2801 Guide d'installation

Velleman HAA2801 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents