Electrohome RS61 Mode d'emploi

Catégorie
Équipement musical supplémentaire
Taper
Mode d'emploi
RS61 – Retro Bluetooth Speaker
Quick Start Guide v1.0
INTRODUCTION
Since 1907 Electrohome has been developing high fidelity audio products & has been welcomed
into homes for generations. One thing that remains the same in our more than 100 year history is
our unmatched dedication to design and premium craftsmanship.
Thank you for your purchase of this Electrohome® product. We hope you enjoy your experience.
Questions?
Give us a chance to help, we’re just a click away.
Electrohome.com/resources
Electrohome.com/contact
Electrohome.com/videos
Electrohome.com/support
Don’t forget to register your product with us!
Electrohome.com/registration
Retro Bluetooth
Speaker
Quick Start Guide
Power Cord
1 Year Warranty
AUX Cable
Lifetime Customer
Support
Guitar Pick
WHAT’S INCLUDED
LIFETIME
Customer Support
Full manual available online at Electrohome.com/resources
PRODUCT INFORMATION
FIRST TIME SETUP
GUITAR
GAIN
GUITAR
INPUT
GUITAR
VOLUME
TREBLE BASS MAIN
VOLUME
1. 1/4 inch Guitar Input
2. Guitar Gain
3. Guitar Volume
4. Treble
5. Bass
6. Main Volume
7. Bluetooth Pairing Reset
8. Bluetooth LED
Flashing – Pairing Mode
Solid - Paired
9. 3.5 mm Aux Audio Input
10. Headphone Jack
11. USB Charging Port – 5V 1.0 Amp
12. Power Jewel Lamp
13. Power Toggle Switch
Connecting to Power
Connect the power cable to the power input on
the back of the RS61 and connect the other end
of the power cable to a power outlet. Note: The
RS61 bass port should be positioned away from any wall.
Turn the System On
Use the power switch located on the front of the
RS61 to turn the unit On and Off. The Power Jewel
Lamp will light up to indicate the unit has power.
1 2 3 4 5 16 12 137 9
8
10 11
GUITAR
GAIN
GUITAR
INPUT
GUITAR
VOLUME
TREBLE BASS MAIN
VOLUME
Adjusting Volume
Use the Main Volume knob to adjust the overall
volume. Note: If playing music from an external device,
the volume of the device should also be adjusted
Adjusting EQ
Use the Bass and Treble knobs to adjust each
from -5 to +5. Note: If playing music from an external
device its EQ settings should be set at or disabled.
GUITAR
GAIN
GUITAR
INPUT
GUITAR
VOLUME
TREBLE BASS
MAIN
VOLUME
GUITAR
GAIN
GUITAR
INPUT
GUITAR
VOLUME
TREBLE BASS
MAIN
VOLUME
Adjusting Guitar Controls
Use the Guitar Volume knob to increase or
decrease the volume of the guitar. This can
be used to balance the guitar volume with the
music volume.
Use the Guitar Gain knob to increase the gain
effect on the guitar signal.
Important: When playing guitar with music, set the
guitar volume rst. Then adjust music volume on
source device to balance them together.
Playing Music Using Bluetooth
Turn on the RS61 and ensure the Bluetooth LED
is flashing. If the LED is not flashing, press the
Bluetooth button to reset pairing.
Important: Connecting an Aux cable to the Aux input
disables the Bluetooth function. To use Bluetooth, the
Aux cable must be disconnected from the RS61.
Playing Music Using Aux Input
Connect an Aux cable from your source device
to the Aux input on the front of the RS61.
Control playback on your source device.
Important: Connecting an Aux cable to the Aux input
disables the Bluetooth input. To use the Bluetooth
input, the Aux cable must be disconnected.
Bluetooth
MY DEVICES
Settings
Electrohome RS61
GUITAR
GAIN
GUITAR
INPUT
GUITAR
VOLUME
TREBLE BASS MAIN
VOLUME
Pair to “Electrohome RS61” on your source device.
You will hear a sound and the Bluetooth LED will
go solid when paired. Control playback on your
source device.
Note: Unit will attempt to auto-pair to the last paired device.
Connecting a Guitar
Connect a 1/4 inch instrument cable to your
guitar’s output jack. Connect the other end of
the cable to the guitar input on the RS61.
Note: The RS61 is not intended to be used with bass guitars,
microphones, or guitar pedals. For best performance, it is
recommended for use with an electric guitar connected
directly to the RS61.
Important: The guitar cable should be disconnected
from the RS61 when the guitar is not in use.
IMPORTANT SAFETY INSTRUCTIONS
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into you outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and point where they exit from
the apparatus.
11. Only use attachments / accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as pow-
er-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. This appliance shall not be exposed to dripping or splashing water and no object filled with liquids such as vases shall be placed on the
apparatus.
16. Do not overload wall outlet. Use only power source as indicated.
17. Use replacement parts as specified by the manufacturer.
18. The product may be mounted to a wall only if recommended by the manufacturer.
19. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks.
20. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was purchased. They can take this product for environ-
mental safe recycling.
21. No naked flame sources, such as lighted candles, should be placed on the apparatus.
22. Attention should be drawn to environmental aspects of battery disposal.
23. Use of the apparatus in moderate climates.
24. WARNING: The appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.
25. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not
perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
26. Do not install this equipment in a confined or building-in space such as a book case or similar unit, and remain a well ventilation
conditions at open site. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper,
table-cloths, curtains etc.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of
uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety
connection to electrical earth.
PRÉCAUTIONS DE SÉCRITÉ IMPORTANTES A LIRE EN PREMIER
AFIN D’ÉVITER TOUT RISQUE DE FEU OU DE RISQUE ÉLECTRIQUE, N’UTILISEZ PAS CETTE PRISE AVEC UNE RALLONGE, UN RÉCEPTACLE OU
UNE AUTRE PRISE À MOINS QUE LES LAMES NE PUISSENT ÊTRE TOTALEMENT INSÉRÉES POUR ÉVITER L’EXPOSITION DES LAMES. POUR
ÉVITER TOUT RISQUE DE FEU OU DE RISQUE ÉLECTRIQUE, N’EXPOSEZ PAS CE MATÉRIEL À L’HUMIDITÉ OU À LA PLUIE.
1. Lisez ces consignes.
2. Gardez ces instructions.
3. Conformez-vous à tous les avertissements.
4. Suivez toutes les consignes applicables.
5. N’utilisez pas cet appareil près de l’eau.
6. Nettoyez uniquement à I’aide d’un chiffon sec.
7. N’obstruez jamais les orifices d’aération de l’appareil et installez-le en conformité avec les instructions du fabricant.
8. N’installez pas l’appareil à proximité d’une source de chaleur telle que radiateurs, registres de chaleur, poêles ou autre appareil (y compris
les amplificateurs) qui produisent de la chaleur.
9. N’allez pas à l’encontre de I’objectif de sécurité de la fiche polarisée ou avec mise à la terre. Une fiche polarisée a deux lames, une étant
plus large que I’autre. Une fiche avec mise à la terre a deux lames et une troisième broche de terre. La lame large ou la troisième broche est
destinée à vous protéger. Si la fiche fournie ne s’insère pas dans votre prise, contactez un électricien pour faire remplacer la prise désuète
10. Empêchez Ie cordon d’être piétiné ou pincé, surtout aux fiches, prises de courant, et au point de leur sortie de I’appareil.
11. Utilisez uniquement les accessoires précisés par Ie fabricant.
12. Utilisez uniquement avec le chariot, le pied, le trépied, le support ou la table spécifiés par le fabricant ou vendus avec l’appareil.
Lorsqu’un chariot est utilisé, faites attention lorsque vous déplacez la combinaison chariot / appareil pour éviter les blessures
dues au renversement.
13. Débranchez cet appareil durant des orages électriques ou lorsqu’il n’est pas utilisé pendant des périodes prolongées.
14. Confiez toutes réparations de cet appareil à un personnel qualifié. Une réparation peut être requise lorsque l’appareil a éte endommagé de
quelque manière que ce soit, tel qu’un cordon ou une fiche endommagé, du liquide déversé ou des objets tombés dans I’appareil, I’appareil
a été exposé à la pluie ou à I’humidité, un appareil qui ne fonctionne pas normalement ou qui est tombé.
15. L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures, et de plus aucun objet rempli de liquide, tel que des
vases, ne doit être placé sur I’appareil.
16. Ne surchargez pas les prises électriques murales ni les cordons de rallonge, car cela risque de causer un incendie ou des chocs électriques.
17. Utilisez des pièces de rechange comme spécifiées par le fabricant.
18. Le produit peut être monté sur un mur seulement si cela est recommandé par le fabricant.
19. Après le service ou une réparation, demandez au technicien d’effectuer des vérifications de sécurité pour s’assurer que l’appareil soit en
bon état de fonctionnement.
20. Élimination correcte de ce produit. Ce marquage indique que ce produit ne doit pas être éliminé avec les autres déchets ménagers
dans l’UE. Pour éviter tout risque pour l’environnement ou la santé humaine d’une élimination incontrôlée des déchets, recyclez-le
de manière responsable afin de promouvoir la réutilisation durable des ressources matérielles. Pour retourner votre appareil usagé,
veuillez utiliser les systèmes de retour et de collecte ou contactez le revendeur chez qui vous avez acheté le produit. Ils peuvent
prendre ce produit pour un recyclage sans danger pour l’environnement.
21. Aucune source de flamme nue, telle que des bougies allumées, ne doit être placée sur l’appareil.
22. L’attention devrait être attirée sur les aspects environnementaux de la mise au rebut des batteries.
23. Utilisation de l’appareil dans des climats modérés.
24. AVERTISSEMENT: le coupleur d’appareil est utilisé comme dispositif de déconnexion, le dispositif de déconnexion doit rester facilement
utilisable.
25. ATTENTION: Ces instructions d’entretien sont destinées à un personnel qualifié. Pour réduire les risques d’électrocution, n’effectuez aucune
opération de maintenance autre que celles décrites dans les instructions d’utilisation, à moins d’être qualifié pour le faire.
26. N’installez pas cet équipement dans un espace confiné ou intégré, tel qu’une bibliothèque ou un meuble similaire, et restez bien ventilé
sur un site ouvert. La ventilation ne doit pas être entravée en recouvrant les orifices de ventilation d’objets tels que du papier journal, des
nappes, des rideaux, etc.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
AVERTISSEMENT: POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, NE RETIREZ PAS LE COUVERCLE (OU LARRIÈRE), POUR L’ENTRETIEN DES
PIECES INTÉRIEURES. VEUILLEZ CONSULTER LE PERSONNEL DE SERVICE QUALIFIÉ.
Le symbole de l’éclair dans un triangle équilatéral a pour but d’alerter l’utilisateur d’une présence d’une tension dangeuse non
isolée dans le boîtier du produit qui pourrait être d’une ampleur suffisante pour constituer un risque de choc électrique aux
personnes.
Le point d’exclamation à l’intérieur d’un triangle équilatéral a pour but d’alerter l’utilisateur de la présence d’instructions impor-
tantes concernant l’utilisation et l’entretient dans le manuel accompagnant cet appareil.
Cet équipement est un appareil électrique de classe II ou à double isolation. Il a été conçu de manière à ne pas nécessiter de connexion
de sécurité à la terre
ATTENTION
RISQUE DE CHOC ÉLECTRIQUE
N’OUVREZ PAS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
WARRANTY INFORMATION
Thank you for choosing Electrohome! We guarantee your investment in our products is a solid one. Our products
come with a complete one-year parts and labor warranty. High performance components combined with quality
craftsmanship allow us to maintain the highest possible production standards. All items are guaranteed against defects
in materials and craftsmanship. Electrohome has outstanding quality control; if something should go wrong with any
of our products, we will repair it free of charge within the warranty period. If the product cannot be repaired, we will
replace the product. In the event that Electrohome replaces a product under warranty, the replacement would only
carry the original warranty from the original date of purchase.
Warranty Exclusions
Electrohome products are warrantied for parts and labor for one year from date of original purchase, and are subject
to the terms and conditions of the warranty. Any refurbished products that are discontinued hold a 90 day warranty
from the date of original purchase. Electrohome warranties are valid for the original owner and are non-transferable.
Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper
installation or inappropriate use as outlined in the owner’s manual.
Any Electrohome product tampered with, modified, adjusted, or repaired by any party other than
Electrohome.
Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
Any damage caused by external or environmental conditions, including but not limited to, transmission
line/power line voltage or liquid spillage.
Any product received without an appropriate model and serial number.
Any products used for rental or commercial purposes.
Any installation, set up and/or programming charges.
To Obtain Warranty Service
Should your product require warranty service, please contact us at www.electrohome.com/contact or call us at
1-855-769-4737 to set up a Return Authorization. Products returned without a valid Return Authorization number
will be refused.
Electrohome products must be returned in their original packaging. Our products are packaged specially to protect
them from any damage during shipping, and without this packaging the return shipment could get damaged.
This warranty does not cover the shipping cost, insurance, or any other incidental charges. Products shipped for
warranty service must be pre-paid by the customer, and Electrohome will cover the cost to ship the repaired or
replaced product back to the customer.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes
or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an
experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20cm between the radiator & your body.
Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites fixées pour un environnement non contrôlé. Cet appareil doit être
installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet transmetteur ne doit pas être co-situé ou opérant
en liaison avec toute autre antenne ou transmetteur.
IC WARNING
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
ELECTROHOME.COM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Electrohome RS61 Mode d'emploi

Catégorie
Équipement musical supplémentaire
Taper
Mode d'emploi

dans d''autres langues