Porter Cable PCC761B Manuel utilisateur

Marque: Porter Cable

Modèle: PCC761B

Catégorie: Ponceuses électriques

Taper: Manuel utilisateur

www.portercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE

SERVICIO Y PÓLIZA DE GARANTÍA.

ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

CATALOG NUMBER

N° DE CATALOGUE

CATÁLOGO N°

PCC761

Instruction manual

Manuel d’instructions

Manual de’instrucciones

*Maximum initial battery pack voltage (measured without a workload) is 20 volts.

The nominal voltage is 18.

*La tension initiale maximale du bloc-piles (mesurée sans charge de travail) est de 20

volts. La tension nominale est de 18.

*El máximo voltaje inicial del paquete de baterías (medido sin una carga de trabajo) es 20

voltios. La tensión nominal es de 18.

20v Max* 4-1/2 inch (115mm) Lithium Cut Off Tool / Grinder

Outil sectionneur 115 mm (4 1/2 po) fil á bloc-piles

au lithium-ion de 20v Max*

Herramienta de corte de 115 mm (4 1/2 pulgada)

iones de litio de 20v Max*

Gracias por elegir PORTER-CABLE usted! Para registrar su nuevo producto,

visite: www.portercable.com / ServiceAndSupport / ProductRegistration.aspx

Merci d’avoir choisi PORTER-CABLE! Consulter le site Web www.portercable.

com/ServiceAndSupport/ProductRegistration.aspx pour enregistrer votre

nouveau produit.

Thank you for choosing PORTER-CABLE! To register your new product, go to:

www.portercable.com/ServiceAndSupport/ProductRegistration.aspx

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

General Power Tool Safety Warnings

WARNING:

Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) WORK AREA SAFETY

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce risk

of electric shock.

b) Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock

if your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) W

hen operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk

of electric shock.

f) If operating a power tool in a damp

location is unavoidable, use a ground

fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of

electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing

and use common sense when

operating a power tool. Do not use a

power tool while you are tired or under

the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, nonskid

safety shoes, hard hat, or hearing

protection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off position before

connecting to power source and/ or

battery pack, picking up or carrying the

tool. Carrying power tools with your finger

on the switch or energizing power tools

that have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating

part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these are

connected and properly used. Use of

dust collection can reduce dust-related

hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job

better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from

the power tool before making any

adjustments, changing accessories,

or storing power tools. Such preventive

safety measures reduce the risk of starting

the power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the power

tool’s operation. If damaged, have the

power tool repaired before use. Many

accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and

tool bits, etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger

specified by the manufacturer. A charger

that is suitable for one type of battery pack

may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep

it away from other metal objects like

paper clips, coins, keys, nails, screws,

or other small metal objects that can

make a connection from one terminal

to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may

be ejected from the battery, avoid

contact. If contact accidentally occurs,

flush with water. If liquid contacts

eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a

qualified repair person using only

identical replacement parts. This will

ensure that the safety of the power

tool is maintained.

SAFETY INSTRUCTIONS FOR ALL

OPERATIONS

Safety Warnings Common for Grinding,

Sanding, Wire Brushing, or Abrasive,

Cutting-Off Operations

a) This power tool is intended to

function as a grinder, sander,

wire brush, or cut-off tool. Read

all safety warnings, instructions,

illustrations and specifications

provided with this power tool. Failure

to follow all instructions listed below

may result in electric shock, fire and/or

serious injury.

b) Operations such as polishing are not

recommended to be performed with

this power tool. Operations for which the

power tool was not designed may create

a hazard and cause personal injury.

c) Do not use accessories which

are not specifically designed

and recommended by the tool

manufacturer. Just because the

accessory can be attached to your power

tool, it does not assure safe operation.

) The rated speed of the accessory

must be at least equal to the maximum

speed marked on the power tool.

Accessories running faster than their

rated speed can break and fly apart.

e) The outside diameter and the

thickness of your accessory must

be within the capacity rating of

your power tool. Incorrectly sized

accessories cannot be adequately

guarded or controlled.

f) Threaded mounting of accessories

must match the grinder spindle

thread. For accessories mounted

by flanges, the arbour hole of the

accessory must fit the locating

diameter of the flange. Accessories

that do not match the mounting

hardware of the power tool will run out

of balance, vibrate excessively and

may cause loss of control.

g) Do not use a damaged accessory.

Before each use inspect the

accessory such as abrasive wheel

for chips and cracks, backing pad

for cracks, tear or excess wear,

wire brush for loose or cracked

wires. If power tool or accessory

is dropped, inspect for damage or

install an undamaged accessory.

After inspecting and installing an

accessory, position yourself and

bystanders away from the plane of

the rotating accessory and run the

power tool at maximum no-load

speed for one minute. Damaged

accessories will normally break apart

during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety

glasses. As appropriate, wear dust

mask, hearing protectors, gloves

and work shop apron capable of

stopping small abrasive or workpiece

fragments. The eye protection must

be capable of stopping flying debris

generated by various operations. The

dust mask or respirator must be capable

of filtrating particles generated by your

operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering

the work area must wear personal

protective equipment. Fragments of

workpiece or of a broken accessory

may fly away and cause injury beyond

immediate area of operation.

j) Hold the power tool by insulated

gripping surfaces only, when

performing an operation where the

cutting tool may contact hidden

wiring. Contact with a “live” wire will

also make exposed metal parts of the

power tool “live” and could give the

operator an electric shock.

k) Position the cord clear of the

spinning accessory. If you lose

control, the cord may be cut or

snagged and your hand or arm may be

pulled into the spinning accessory.

l) Never lay the power tool down

until the accessory has come

to a complete stop. The spinning

accessory may grab the surface and

pull the power tool out of your control.

m) Do not run the power tool while

carrying it at your side. Accidental

contact with the spinning accessory

could snag your clothing, pulling the

accessory into your body.

n) Regularly clean the power tool’s air

vents. The motor’s fan will draw the

dust inside the housing and excessive

accumulation of powdered metal may

cause electrical hazards.

o) Do not operate the power tool

near flammable materials. Sparks

could ignite these materials.

p) Do not use accessories that require

liquid coolants. Using water or

other liquid coolants may result in

electrocution or shock.

q) Do not use Type 11 (flaring cup)

wheels on this tool. Using inappropriate

accessories can result in injury.

r) Always use side handle. Tighten

the handle securely. The side handle

hould always be used to maintain

control of the tool at all times.

s) When starting the tool with a new

or replacement wheel, or a new or

replacement wire brush installed,

hold the tool in a well protected area

and let it run for one minute. If the

wheel has an undetected crack or flaw,

it should burst in less than one minute.

If the wire brush has loose wires, they

will be detected. Never start the tool

with a person in line with the wheel.

This includes the operator.

t) T

o prevent the spindle end from

contacting the bottom of the

hole of the abrasive product, use

accessories that have a threaded

hole depth of at least 21mm. Failure to

use an accessory with the appropriate

thread depth could result in damage to

the abrasive product and injury to the

operator or persons in the area.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a

pinched or snagged rotating wheel,

backing pad, brush or any other

accessory. Pinching or snagging causes

rapid stalling of the rotating accessory

which in turn causes the uncontrolled

power tool to be forced in the direction

opposite of the accessory’s rotation at

the point of the binding.

For example, if an abrasive wheel is

snagged or pinched by the workpiece,

the edge of the wheel that is entering

into the pinch point can dig into the

surface of the material causing the

wheel to climb out or kick out. The

wheel may either jump toward or

away from the operator, depending on

direction of the wheel’s movement at

the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of tool misuse and/

or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below:

a) Maintain a firm grip on the power

tool and position your body and

arm to allow you to resist kickback

forces. Always use auxiliary handle,

if provided, for maximum control

over kickback or torque reaction

during start up. The operator can

control torque reaction or kickback

forces, if proper precautions are taken.

b) Never place your hand near the

rotating accessory. Accessory may

kickback over your hand.

c) Do not position your body in the

area where power tool will move if

kickback occurs. Kickback will propel the

tool in direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working

corners, sharp edges etc. Avoid

bouncing and snagging the

accessory. Corners, sharp edges or

bouncing have a tendency to snag the

rotating accessory and cause loss of

control or kickback.

e) Do not attach a saw chain

woodcarving blade or toothed saw

blade. Such blades create frequent

kickback and loss of control.

SAFETY WARNINGS

SPECIFIC FOR GRINDING

AND ABRASIVE CUTTING-

OFF OPERATIONS

a) Use only wheel types that are re-

commended for your power tool and

the specific guard designed for the

selected wheel. Wheels for which the

power tool was not designed cannot be

adequately guarded and are unsafe.

b) The grinding surface of the center

depressed wheels must be mounted

below the plane of the guard lip. An

improperly mounted wheel that projects

through the plane of the guard lip

cannot be adequately protected.

c) The guard must be securely

attached to the power tool and

positioned for maximum safety,

so the least amount of wheel is

exposed towards the operator. The

guard helps to protect operator from

broken wheel fragments, accidental

contact with wheel and sparks that

could ignite clothing.

d) Wheels must be used only for

recommended applications. For

example: do not grind with the side

of cut-off wheel. Abrasive cut-off

wheels are intended for peripheral

grinding, side forces applied to these

wheels may cause them to shatter.

e) Always use undamaged wheel flanges

that are of correct size and shape for

your selected wheel. Proper wheel

flanges support the wheel thus reducing

the possibility of wheel breakage. Flanges

for cut-off wheels may be different from

grinding wheel flanges.

f) Do not use worn down wheels from

larger power tools. Wheel intended for

larger power tool is not suitable for the

higher speed of a smaller tool and may

burst.

ADDITIONAL SAFETY WARNINGS

SPECIFIC FOR ABRASIVE CUTTING-

OFF OPERATION

a) Do not “jam” the cut-off wheel

or apply excessive pressure. Do

not attempt to make an excessive

depth of cut. Over stressing the

wheel increases the loading and

susceptibility to twisting or binding of

the wheel in the cut and the possibility

of kickback or wheel breakage.

b) Do not position your body in line

with and behind the rotating wheel.

When the wheel, at the point of

operation, is moving away from your

body, the possible kickback may

propel the spinning wheel and the

power tool directly at you.

c) When wheel is binding or when

interrupting a cut for any reason,

switch off the power tool and hold

the power tool motionless until the

wheel comes to a complete stop.

Nev

er attempt to remove the cut-off

wheel from the cut while the wheel is in

motion otherwise kickback may occur.

Investigate and take corrective action to

eliminate the cause of wheel binding.

d) Do not restart the cutting operation

in the workpiece. Let the wheel

reach full speed and carefully

reenter the cut. The wheel may bind,

walk up or kickback if the power tool is

restarted in the workpiece.

e) Support panels or any oversized

workpiece to minimize the risk

of wheel pinching and kickback.

Large workpieces tend to sag under

their own weight. Supports must be

placed under the workpiece near the

line of cut and near the edge of the

workpiece on both sides of the wheel.

f) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding

wheel may cut gas or water pipes,

electrical wiring or objects that can

cause kickback.

g) It is recommended to use grinding/

cutting wheels no thicker than 1/4

inch (6mm) thick.

SAFETY WARNINGS SPECIFIC FOR

SANDING OPERATIONS

a) Do not use excessively oversized

sanding disc paper. Follow

manufacturers recommendations,

when selecting sanding paper. Larger

sanding paper extending beyond the

sanding pad presents a laceration

hazard and may cause snagging, tearing

of the disc or kickback.

SAFETY WARNINGS SPECIFIC FOR

WIRE BRUSHING OPERATIONS

a) Be aware that wire bristles are

thrown by the brush even during

ordinary operation. Do not

overstress the wires by applying

excessive load to the brush. The

wire bristles can easily penetrate light

clothing and/or skin.

If the use of a guard is

recommended for wire brushing, do

not allow any interference of the wire

wheel or brush with the guard. Wire

wheel or brush may expand in diameter

due to work and centrifugal forces.

c) Safety glasses: Safety Goggles or safety

glasses with side shields and a full face

shield compliant with ANSI Z87.1 eye

protection (CAN/CPA Z94.3), must be worn

by the operator and others that are within

50 feet of the use of this product/accessory.

ADDITIONAL SAFETY INFORMATION

•

Do not use Type 1 flat cut-off abrasive or

diamond wheels without proper guard.

WARNING: Always wear proper

personal hearing protection that

conforms to ANSI S12.6 (S3.19) during

use. Under some conditions and duration

of use, noise from this product may

contribute to hearing loss.

WARNING: ALWAYS use safety

glasses. Everyday eyeglasses are NOT

safety glasses. Also use face or dust

mask if cutting operation is dusty.

ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

 •

ANSI Z87.1 eye protection (CAN/CSA Z94.3),

 •ANSIS12.6(S3.19)hearingprotection,

 •

NIOSH/OSHA/MSHA respiratory protection.

WARNING:

Some dust created by

power sanding, sawing, grinding,

drilling, and other construction activities

contains chemicals known to the state of

California to cause cancer, birth defects

or other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement

and other masonry products, and

• arsenic and chromium from

chemically-treated lumber.

Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area,

and work with approved safety equipment,

such as those dust masks that are specially

designed to filter out microscopic particles.

•Avoid prolonged contact with dust

from power sanding, sawing, grinding,

drilling, and other construction

activities. Wear protective clothing

and wash exposed areas with soap

and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING:

Use of this tool can

generate and/or disperse dust, which may

cause serious and permanent respiratory

or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate

for the dust exposure. Direct particles away

from face and body.

WARNING: Do not operate this tool

for long periods of time. Vibration

caused by the operating action of this

tool may cause permanent injury to

fingers, hands, and arms. Use gloves to

provide extra cushion, take frequent rest

periods, and limit daily time of use.

WARNING: When not in use, place

grinder on a stable surface where it will

not move inadvertently, roll or cause a

tripping or falling hazard. The grinder

may stand upright on the battery pack

but may be easily knocked over. Serious

personal injury may result.

CAUTION: To reduce the risk of

personal injury, use extra care when

working into a corner or edge because a

sudden, sharp movement of the tool may

be experienced when the wheel or other

accessory contacts a secondary surface

or a surface edge.

•

When using an extension cord, be sure to

use one heavy enough to carry the current

your product will draw. An undersized cord

will cause a drop in line voltage resulting

in loss of power and overheating. The

following table shows the correct size

to use depending on cord length and

nameplate ampere rating. If in doubt, use

the next heavier gage. The smaller the

gage number, the heavier the cord.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

  (0-7,6m)(7,6-15,2m)(15,2-30,4m)(30,4-45,7m)

Ampere Rating

More Not more American Wire Gauge

Than Than

6 - 10 18 16 14 12

SAVE THESE INSTRUCTIONS

SYMBOLS

The label on your tool may include the

following symbols. The symbols and their

definitions are as follows:

V ......................volts

A ......................amperes

Hz ....................hertz

W .....................watts

min ...................minutes

....................alternating current

or DC ........direct current

o ....................no load speed

n.......................rated speed

.....................Class I Construction

(grounded)

.....................earthing terminal

...................safety alert symbol

..................... Class II Construction

(double insulated)

.../min or rpm...revolutions or

reciprocation per minute

SPM .................Strokes per minute

5/8 -11 …………. Arbor size and Thread

count per inch

.................

Read instruction manual before use

.....................Use proper eye protection

.....................Use proper hearing protection

........................

Use proper respiratory protection

IMPORTANT SAFETY

INSTRUCTIONS FOR

BATTERY CHARGERS

SAVE THESE INSTRUCTIONS: This

manual contains important safety

instructions for battery chargers.

•

efore using charger, read all instructions

and cautionary markings on charger, battery

pack, and product using battery pack.

WARNING: Shock hazard. Do not

allow any liquid to get inside charger.

CAUTION: Burn hazard.

To reduce the

risk of injury, charge only designated

PORTER-CABLE batteries. Other types

of batteries may burst causing personal

injury and damage.

CAUTION: Under certain conditions,

with the charger plugged in to the power

supply, the charger can be shorted by foreign

material. Foreign materials of a conductive nature

such as, but not limited to, steel wool, aluminum

foil, or any buildup of metallic particles should be

kept away from charger cavities. Always unplug

the charger from the power supply when there

is no battery pack in the cavity. Unplug charger

before attempting to clean.

•

DO NOT attempt to charge the battery

pack with any chargers other than the

ones in this manual. The charger and

battery pack are specifically designed

to work together.

•

These chargers are not intended for any

uses other than charging designated

PORTER-CABLE rechargeable

batteries. Any other uses may result

in risk of fire, electric shock or

electrocution.

•Do not expose charger to rain or snow.

•Pull by plug rather than cord when

disconnecting charger. This will reduce

risk of damage to electric plug and cord.

•Make sure that cord is located so that it

will not be stepped on, tripped over, or

otherwise subjected to damage or stress.

•Do not use an extension cord unless it is

absolutely necessary. Use of improper

extension cord could result in risk of fire,

electric shock, or electrocution.

•An extension cord must have adequate

wire size (AWG or American Wire Gauge)

for safety. The smaller the gauge number

of the wire, the greater the capacity of the

cable,thatis16gaugehasmorecapacity

than 18 gauge. When using more than one

extension to make up the total length, be

sure each individual extension contains at

least the minimum wire size.

•Do not place any object on top of

charger or place the charger on a soft

surface that might block the ventilation

slots and result in excessive internal

heat. Place the charger in a position

away from any heat source. The charger

is ventilated through slots in the top and the

bottom of the housing.

•Do not mount charger on wall or

permanently affix charger to any surface.

The charger is intended to use on a flat,

stable surface (i.e., table top, bench top).

• Do not operate charger with damaged cord

or plug — have them replaced immediately.

•Do not operate charger if it has

received a sharp blow, been dropped,

or otherwise damaged in any way. Take

it to an authorized service center.

•Do not disassemble charger; take it to

an authorized service center when service

or repair is required. Incorrect reassembly

may result in a risk of electric shock,

electrocution or fire.

•

Disconnect the charger from the outlet

before attempting any cleaning. This will

reduce the risk of electric shock. Removing

the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

•The charger is designed to operate on

standard household electrical power

(120 Volts). Do not attempt to use it on

any other voltage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTION

FOR BATTERY PACKS

WARNING:

For safe operation, read

this manual and manuals originally

supplied with tool before using the charger.

The battery pack is not fully charged out of

the carton. Before using the battery pack and

charger, read the safety instructions below.

Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

•

Do not incinerate the battery pack even

if it is severely damaged or is completely

worn out. The battery pack can explode

in a fire. Toxic fumes and materials are

created when battery packs are burned.

•

Do not charge or use battery in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting

or removing the battery from the charger

may ignite the dust or fumes.

•

If battery contents come into contact

with the skin, immediately wash area

with mild soap and water. If battery liquid

gets into the eye, rinse water over the

open eye for 15 minutes or until irritation

ceases. If medical attention is needed, the

battery electrolyte for Lithium-Ion batteries

is composed of a mixture of liquid organic

carbonates and lithium salts.

•Contents of opened battery cells may

cause respiratory irritation. Provide

fresh air. If symptoms persist, seek

medical attention.

WARNING:

Burn hazard. Battery

liquid may be flammable if exposed to

spark or flame.

•Charge the battery packs only in

PORTER-CABLE chargers.

• DO NOT splash or immerse in water or other

liquids. This may cause premature cell failure.

• Do not store or use the tool and battery

pack in locations where the temperature

may reach or exceed 105°F (40˚C) (such as

outside sheds or metal buildings in summer).

WARNING: Never attempt to open

the battery pack for any reason. If battery

pack case is cracked or damaged, do not

insert into charger. Do not crush, drop or

damage battery pack. Do not use a

battery pack or charger that has received

a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a

nail, hit with a hammer, stepped on).

Damaged battery packs should be

returned to service center for recycling.

WARNING:

Fire hazard. Do not store

or carry battery so that metal objects can

contact exposed battery terminals. For

example, do not place battery in aprons,

pockets, tool boxes, product kit boxes,

drawers, etc., with loose nails, screws, keys,

etc. Transporting batteries can possibly

cause fires if the battery terminals

inadvertently come in contact with

conductive materials such as keys, coins,

hand tools and the like. The US Department

of Transportation Hazardous Material

Regulations (HMR) actually prohibit

transporting batteries in commerce or on

airplanes (i.e., packed in suitcases and

carry-on luggage) UNLESS they are

properly protected from short circuits. So

when transporting individual batteries, make

sure that the battery terminals are protected

and well insulated from materials that could

contact them and cause a short circuit.

NOTE: Lithium-Ion batteries should not

be put in checked baggage.

STORAGE RECOMMENDATIONS

The best storage place is one that is

cool and dry away from direct sunlight and

excess heat or cold.

2.Long-termstoragewillnotharmthe

battery pack or charger as long as the

battery is not depleted.

IMPORTANT CHARGING NOTES

1. Longest life and best performance can be

obtained if the battery pack is charged when

theairtemperatureisbetween65°Fand

75°F(18°-24°C).DONOTchargethebattery

packinanairtemperaturebelow+40°F

(+4.5°C),orabove+105°F(+40.5°C).Thisis

important and will prevent serious damage to

the battery pack.

2.Thechargerandbatterypackmaybecome

warm to touch while charging. This is a normal

condition, and does not indicate a problem. To

facilitate the cooling of the battery pack after

use, avoid placing the charger or battery pack

in a warm environment such as in a metal

shed, or an uninsulated trailer.

If the battery pack does not charge

properly:

a. Check current at receptacle by

plugging in a lamp or other appliance.

b. Check to see if receptacle is

connected to a light switch which turns

power off when you turn out the lights.

c. Move charger and battery pack to a

location where the surrounding air

temperatureisapproximately65°F-

75°F(18°-24°C).

d. If charging problems persist, take the

tool, battery pack and charger to your

local service center.

4. The battery pack should be recharged

when it fails to produce sufficient power

on jobs which were easily done previously.

DO NOT CONTINUE to use under these

conditions. Follow the charging procedure.

You may also charge a partially used pack

whenever you desire with no adverse

affect on the battery pack.

5.Foreignmaterialsofaconductive

nature such as, but not limited to, steel

wool, aluminum foil, or any buildup of

metallic particles should be kept away

from charger cavities. Always unplug the

charger from the power supply when there

is no battery pack in the cavity. Unplug

charger before attempting to clean.

6.Donotfreezeorimmersechargerin

water or any other liquid.

WARNING: Shock hazard. Do not

allow any liquid to get inside charger.Never

attempt to open the battery pack for any

reason. If the plastic housing of the

battery pack breaks or cracks, return to a

service center for recycling.

Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished.

FUNCTIONAL DESCRIPTION

FIGURE A

1. Trigger Switch

2.Lock-OffButton

3. Spindle Lock Button

4. Spindle (not shown)

5.SideHandle

6.AbrasiveWheel

7. Unthreaded Backing Flange (not shown)

8. Threaded Clamp Nut (not shown)

9.Guard(Type1,Type27)

This product uses the batteries and chargers listed below.

20V Max* Lithium-Ion Batteries: PCC680L, PCC681L, PCC685L, PCC682L

20V Max* Lithium-Ion Chargers: PCC690L, PCC691L, PCC695L, PCC692L

1/4 inch wheels

Backing flange

Threaded clamp nut

20˚-30˚

1/8 inch wheels

Backing flange

Threaded clamp nut

5˚-10˚

5˚-15˚

4-1/2 inch (115mm) Grinding Wheels

Unthreaded backing flange

Threaded clamp nut

Type 27 hubbed wheel

Type 27 guard

Type 27 depressed center

wheel

Type 27 guard

4-1/2 inch (115mm) Sanding Flap Discs

Hubbed sanding flap disc

Threaded clamp nut

non-hubbed sanding flap disc

Type 27 guard

Unthreaded backing flange

4-1/2 inch (115mm) Type 1 Cutting Wheels

Clamp nut

diamond cutting whee

Type 1 guard

Backing flange

abrasive cutting wheel

Clamp nut

3 inch wire cup brush

4 inch wire cup brush

Wire Wheels

Type 27 guard

Protector tipo 27

Type 27 guard

Rubber backing pad

Sanding disc

Threaded clamp nut

Sanding Discs

CHARGING PROCEDURE

PORTER-CABLE chargers are designed

to charge PORTER-CABLE battery packs.

Chargetimesare:PCC690LandPCC692L

in35-100mins.,PCC691Lin65-200mins.

andPCC695Lin160-300mins.depending

on the pack being charged.

1. Plug the charger into an appropriate

outlet before inserting the battery pack.

2.Figure B- Insert the battery pack into the charger.

3. The LED will flash indicating that

the battery is being charged.

4. The completion of charge is indicated

by the LED remaining on continuously.

The pack is fully charged and may be

used at this time or left on the charger.

CHARGER DIAGNOSTICS

This charger is designed to detect certain

problems that can arise with the battery

packs or the power source. Problems are

indicated by one LED flashing in different

patterns.

BAD BATTERY

The charger can detect a weak or

damaged battery. The LED flashes

in the pattern indicated on the label. If you

see this bad battery blink pattern, do not

continue to charge the battery. Return it

to a service center or a collection site for

recycling.

HOT/COLD PACK DELAY

When the charger detects a battery

that is excessively hot or excessively

cold, it automatically starts a Hot/Cold

Pack Delay, suspending charging until the

battery has normalized. After this happens,

the charger automatically switches to the

Pack Charging mode. This feature ensures

maximum battery life. The light flashes in

the pattern indicated on the label.

PROBLEM POWER LINE

When the charger is used with some

portable power sources such as

generators or sources that convert DC to

AC, the charger may temporarily suspend

operation. The LED flashes in the pattern

indicated on the label. This indicates that

the power source is out of limits.

LEAVING THE BATTERY IN THE CHARGER

The charger and battery pack can be left

connected with the LED glowing indefinitely.

The charger will keep the battery pack fresh

and fully charged. This charger features an

automatic tune-up mode which equals or

balances the individual cells in the battery

pack to allow it to function at peak capacity.

Battery packs should be tuned up weekly or

whenever the battery no longer delivers the

same amount of work. To use the automatic

tune-up mode, place the battery pack in the

charger and leave it for at least 8 hours.

INSTALLATION AND REMOVAL OF

THE BATTERY PACK

INSTALL BATTERY PACK: Figure

C-

Insert battery pack onto the tool until an

audible click is heard. Make sure battery pack

is fully seated and fully latched into position.

TO REMOVE BATTERY PACK: D

epress

the battery release button as shown in figure

D and pull battery pack out of the tool.

OPERATING INSTRUCTIONS

WARNING:

Always use proper eye

protection that conforms to ANSI Z87.1(CAN/

CSA Z94.3) while operating this power tool.

WARNING: Use clamps or another

practical way to secure and support the

work piece to a stable platform. Holding the

work by hand or against your body leaves it

unstable and may lead to loss of control.

NOTE: Before cutting any type of

material, be sure it is firmly anchored or

clamped to prevent slipping.

TRIGGER SWITCH

The tool is equipped with a switch lock-off

feature to prevent unintentional operation.

•Toswitchthetoolon,pressthelockoff

button(2),

then squeeze the on/off switch (1).

•

Releasing the trigger turns the motor OFF.

NOTE: This tool has no provision to lock

the switch in the ON position, and should

never be locked in the ON position by any

other means.

These utilize a carbon steel back welded

to high speed steel teeth making the blade

more flexible and less prone to breaking

ASSEMBLY

WARNING: To prevent accidental

operation, turn off tool and remove

battery before making any adjustments or

removing or installing attachments or

accessories. Failure to do this could result

in serious personal injury.

ATTACHING THE SIDE HANDLE

• Athreepositionauxiliaryhandle(5) is

furnished with your grinder and can be

screwed into either side of the grinder

housing as well as into the top.

WARNING: This handle

SHOULD BE USED AT ALL TIMES to

maintain complete control of the tool.

Always make sure the handle is tight.

ACCESSORIES

It is important to choose the correct

guards, backing pads and flanges to use

with grinder accessories.

CAUTION: Accessories must be rated

for at least the speed recom mended on the

tool warning label. Wheels and other

accessories running over their rated

accessory speed may fly apart and cause

injury.Threadedaccessoriesmusthavea5/8

inch-11 hub. Every unthreaded accessory

musthavea7/8inch(22mm)arborhole.Ifit

does not, it may have been designed for a

circular saw. Use only the accessories shown

onpages10and11ofthismanual.

Accessory ratings must always be above tool

speed as shown on tool nameplate.

MOUNTING GUARD

MOUNTING AND REMOVING GUARD

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

Guards must be used with all grinding

wheels, sanding flap discs, wire brushes,

cut-off wheels and wire wheels. The

tool may be used without a guard only

when sanding with conventional sanding

discs.PorterCablemodelPCC671is

provided with a guard intended for use with

depressedcenterwheels(Type27)and

hubbedgrindingwheels(Type27).Thesame

guard is designed for use with sanding

flapdiscs(Type27and29)andwirecup

brushes. Grinding and cutting with wheels

otherthanType27and29requiredifferent

accessory guards included with tool. A Type

1 guard is provided for use with a Type 1

wheel and is shown in figures E and F.

Both Type 27 and Type 1 guards attach

and are removed in the same way as

described in figures E and F.

FIGURE E

ATTACHING-Opentheguardlatch(10),

and align the lugs on the guard (9) with

the slots on the gear case cover.

2. Pushtheguarddownuntiltheguard

lugs engage and rotate freely in the

groove on the gear case hub.

3. With the guard latch open, rotate the

guard (9) into the desired working position.

The guard body should be positioned

between the spindle and the operator to

provide maximum operator protection.

4. F

igure F - Close the guard latch to

secure the guard on the gear case. You

should not be able to rotate the guard by

hand when the latch is closed. Do not

operate the grinder with a loose guard or

the clamp lever in open position.

5. REMOVING-Toremovetheguard,

open the guard latch, rotate the guard

so that the lugs on the guard (9) are

aligned with the slots on the gear case

cover, and pull up on the guard.

FIGURE G

NOTE:

The guard is pre-adjusted to

the diameter of the gear case hub at the

factory. If, after a period of time, the guard

becomes loose, tighten the adjusting

screw(12)withlatchintheclosedposition

and guard installed on the tool.

Do not tighten the adjusting screw with the

latch in the open position. Undetectable

damage to the guard or the mounting hub

may result. If the guard cannot be tightened

by the guard latch, do not use the tool and

take the tool and guard to a service center

to repair or replace the guard.

NOTE:

Edge grinding and cutting can be

performedwithType27wheelsdesignedand

specifiedforthispurpose;1/4inch(6mm)

thick wheels are designed for surface grinding

while 1/8 inch (3mm) wheels are designed for

edge grinding. Cutting can also be performed

by using a Type 1 wheel and a Type 1 guard.

OPERATION

SWITCH - FIGURE H & I

Lock-off Button and Trigger Switch

Your cut-off tool is equipped with a lock-off

button(2).

To lock the trigger switch (1), move the

lock-offbutton(2)totherearasshownin

Figure H. When the lock-off button is moved

to this position, the trigger switch is locked.

Always lock the trigger switch when

carrying or storing the tool to eliminate

unintentional starting.

To unlock the trigger switch, move the

lock-off button to the front as shown in Figure I.

When the lock-off button is moved to this

position, the trigger switch is unlocked.

Pull the trigger switch (1) to turn the motor

ON. Releasing the trigger switch turns the

motor OFF.

NOTE:

This tool has no provision to lock the

switch in the ON position, and should never be

locked ON by any other means.

Holdthesidehandle(5)andbodyofthetool

firmly to maintain control of the tool at start up

and during use and until the wheel or accessory

stops rotating. Make sure the wheel has come to

a complete stop be fore laying the tool down.

Allow the tool to reach full speed before

touching tool to the work surface. Lift the tool

from the work surface before turning the tool off.

SPINDLE LOCK

The spindle lock button (3) is provided to

prevent the spindle from rotating when

installing or removing wheels. Operate the

spindle lock only when the tool is turned

off, the battery is removed, and the wheel

has come to a complete stop.

Do not engage the spindle lock while the

tool is operating. Damage to the tool will

result and attached accessory may spin off

possibly resulting in injury.

To engage the lock, depress the spindle

lock button shown in figure J and rotate

the spindle until you are unable to rotate the

spindle further.

MOUNTING AND USING DEPRESSED

CENTER GRINDING WHEELS AND

SANDING FLAP DISCS

MOUNTING AND REMOVING HUBBED

WHEELS

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

Hubbedwheelsinstalldirectlyonthe5/8

in.-11 threaded spindle.

1. Thread the wheel on the spindle by hand.

2. Depressthespindlelockbuttonanduse

a wrench to tighten the hub of the wheel.

3. Reverse the above procedure to remove

the wheel.

Failure to properly seat the wheel before

turning the tool on may result in damage to

the tool or the wheel.

MOUNTING NON-HUBBED WHEELS

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

DepressedcenterType27grindingwheels

must be used with included flanges. See pages

13 and 14 of this manual for more information.

Figure K - Install the unthreaded

backing flange (7) on spindle (4) with the

raised section (pilot) against the wheel.

2. Placewheelagainstthebackingflange,

centering the wheel on the raised

section (pilot) of the backing flange.

Figure L - While depressing the spindle lock button,

thread the threaded clamp nut (8) on spindle.

Figure M - If the wheel you are installing

is more than 1/8 inch (3mm) thick,

place the threaded clamp nut on the

spindle so that the raised section (pilot)

fits into the center of the wheel. Figure N - If

the wheel you are installing is 1/8 inch (3mm)

thick or less, place the threaded clamp nut on

the spindle so that the raised section (pilot) is

not against the wheel.

4. While depressing the spindle lock

button (3), tighten the threaded clamp

nut with included wrench.

5.

To remove the wheel, depress the spindle

lock button and loosen the threaded

clamp nut with included wrench.

NOTE: If the wheel spins after the

threaded clamp nut is tightened, check the

orientation of the threaded clamp nut. If a

thin wheel is installed with the pilot on the

clamp nut against the wheel, it will spin

because the height of the pilot prevents the

clamp nut from holding the wheel.

SURFACE GRINDING WITH GRINDING WHEELS

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Applyminimumpressuretothework

surface, allowing the tool to operate at

high speed. Grinding rate is greatest

when the tool operates at high speed.

3. Figure O - Maintain a 20˚ to 30˚ angle

between the tool and work surface.

4. Continuously move the tool in a forward

and back motion to avoid creating

gouges in the work surface.

5. Removethetoolfromworksurface

before turning tool off. Allow the tool to

stop rotating before laying it down.

EDGE GRINDING WITH GRINDING WHEELS

Wheels used for cutting and edge grinding

may break or kick back if they bend or twist

while the tool is being used to do cut-off

work or deep grinding. To reduce the risk of

serious injury, limit the use of these wheels

withastandardType27guardtoshallow

cuttingandnotching(lessthan1/2inch

(13mm) in depth). The open side of the

guard must be positioned away from the

operator. For deeper cutting with a Type 1

cut-off wheel, use a closed Type 1 guard.

See pages 13 and 14 for more information.

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Applyminimumpressuretothework

surface, allowing the tool to operate at

high speed. Grinding rate is greatest

when the tool operates at high speed.

3. Position yourself so that the open-

underside of the wheel is facing away

from you.

4. Once a cut is begun and a notch is

established in the workpiece, do not

change the angle of the cut. Changing the

angle will cause the wheel to bend and

may cause wheel breakage. Edge grinding

wheels are not designed to withstand side

pressures caused by bending.

5.

Remove the tool from the work surface

before turning the tool off. Allow the tool

to stop rotating before laying it down.

Do not use edge grinding/cutting wheels for

surface grinding applications because these

wheels are not designed for side pressures

encountered with surface grinding. Wheel

breakage and injury may result.

SURFACE FINISHING WITH SANDING

FLAP DISCS

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Applyminimumpressuretowork

surface, allowing the tool to operate at

high speed. Sanding rate is greatest

when the tool operates at high speed.

3. Figure P - Maintain a 5˚ to 10˚ angle

between the tool and work surface.

4. Continuously move the tool in a

forward and back motion to avoid

creating gouges in the work surface.

5. Removethetoolfromworksurface

before turning tool off. Allow the tool to

stop rotating before laying it down.

MOUNTING SANDING BACKING PADS

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

NOTE: Guard may be removed when

using sanding backing pads

Proper guard must be reinstalled for grinding

wheel, sanding flap disc, cutoff wheel,

wire brush or wire wheel applications after

sanding applications are complete.

1. Figure Q - Place or appropriately

thread backing pad (13) on the spindle.

2. Placethesandingdisc(14)onthe

backing pad (13).

3. While depressing spindle lock, thread

clamp nut (8) on spindle, piloting the

raised hub on the clamp nut into the

center of san ding disc and backing pad.

4. Tighten the clamp nut by hand. Then

depress the spindle lock button while

turning the sanding disc until the

sanding disc and clamp nut are snug.

5. Toremovethewheel,graspandturn

the backing pad and sanding pad while

depressing the spindle lock button.

USING SANDING BACKING PADS

Choose the proper grit sanding discs for

your application. Sanding discs are available

in various grits. Coarse grits yield faster

material removal rates and a rougher finish.

Finer grits yield slower material removal and

a smoother finish.

Begin with coarse grit discs for fast, rough

material removal. Move to a medium grit

paper and finish with a fine grit disc for

optimal finish.

Coarse 16-30grit

Medium 36-80grit

FineFinishing 100-120grit

VeryFineFinishing 150-180grit

1. Allow the tool to reach full speed before

touching tool to the work surface.

2. Applyminimumpressuretowork

surface, allowing the tool to operate at

high speed. Sanding rate is greatest

when the tool operates at high speed.

igure R - Maintaina5˚to15˚angle

between the tool and work surface. The

san ding disc should contact approximately

oneinch(25mm)ofworksurface.

4. Move the tool constantly in a straight

line to prevent burning and swirling of

work surface. Allowing the tool to rest

on the work surface without moving,

or moving the tool in a circular motion

causes burning and swirling marks on

the work surface.

5. Removethetoolfromworksurface

before turning tool off. Allow the tool to

stop rotating before laying it down.

PRECAUTIONS TO TAKE WHEN

SANDING PAINT

1. Sanding of lead based paint is NOT

RECOMMENDED due to the difficulty of

controlling the contaminated dust. The

greatest danger of lead poisoning is to

children and pregnant women.

2.

ince it is difficult to identify whether or not

a paint contains lead without a chemical

analysis, we recommend the following

precautions when sanding any paint:

PERSONAL SAFETY

1. No children or pregnant women should enter

the work area where the paint sanding is

being done until all clean up is completed.

2.

A dust mask or respirator should be worn

by all persons entering the work area. The

filter should be replaced daily or whenever

the wearer has difficulty breathing.

NOTE: Only those dust masks

suitable for working with lead paint

dust and fumes should be used.

Ordinary painting masks do not offer

this protection. See your local hardware

dealer for the proper N.I.O.S.H.

approved mask.

3. NO EATING, DRINKING or SMOKING

should be done in the work area to

prevent ingesting contaminated paint

particles. Workers should wash and

clean up BEFORE eating, drinking or

smoking. Articles of food, drink, or

smoking should not be left in the work

area where dust would settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a

manner as to minimize the amount of

dust generated.

2. Areaswherepaintremovalisoccurring

should be sealed with plastic sheeting

of 4 mils thickness.

3. Sanding should be done in a manner

to reduce tracking of paint dust outside

the work area.

CLEANING AND DISPOSAL

All surfaces in the work area should be

vacuumed and thoroughly cleaned daily for

the duration of the sanding project. Vacuum

filter bags should be changed frequently.

2. Plasticdropclothsshouldbegathered

up and disposed of along with any

dust chips or other removal debris.

They should be placed in sealed refuse

receptacles and disposed of through

regular trash pick-up procedures.

During clean up, children and pregnant

women should be kept away from the

immediate work area.

3. All toys, washable furniture and utensils

used by children should be washed

thoroughly before being used again.

MOUNTING AND USING WIRE

BRUSHES AND WIRE WHEELS

Wire cup brushes or wire wheels screw

directly on the grinder spindle without

the use of flanges. Use only wire brushes

orwheelsprovidedwitha5/8inch-11

threadedhub.AType27guardisrequired

when using wire brushes and wheels. Wear

work gloves when handling wire brushes

and wheels. They can become sharp.

Wheel or brush must not touch guard when

mounted or while in use. Undetectable

damage could occur to the accessory,

causing wires to fragment from accessory

wheel or cup.

MOUNTING WIRE CUP BRUSHES AND

WIRE WHEELS

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

1. Thread the wheel on the spindle by hand.

2. Depressspindlelockbuttonandusea

wrench on the hub of the wire wheel or

brush to tighten the wheel.

3. To remove the wheel, reverse the above

procedure.

Failure to properly seat the wheel hub

before turning the tool on may result in

damage to tool or wheel.

USING WIRE CUP BRUSHES AND WIRE WHEELS

Wire wheels and brushes can be used for

removing rust, scale and paint, and for

smoothing irregular surfaces.

NOTE: The same precautions should be

taken when wire brushng paint as when

sanding paint.

1. Allow the tool to reach full speed before

touching the tool to the work surface.

2. Applyminimumpressuretoworksurface,

allowing the tool to operate at high

speed. Material removal rate is greatest

when the tool operates at high speed.

3. Figure S -Maintaina5˚to10˚angle

between the tool and work surface for

wire cup brushes.

4. Maintain contact between the edge of

the wheel and the work surface with

wire wheels.

5. Continuouslymovethetoolinaforward

and back motion to avoid creating

gouges in the work surface. Allowing

the tool to rest on the work surface

without moving, or moving the tool in

a circular motion causes burning and

swirling marks on the work surface.

6. Removethetoolfromtheworksurface

before turning the tool off. Allow the tool

to stop rotating before setting it down.

Use extra care when working over an

edge, as a sudden sharp movement of

grinder may be experienced.

MOUNTING AND USING CUTTING

(TYPE 1) WHEELS

Cutting wheels include diamond wheels and

abrasive discs. Abrasive cutting wheels for

metal and concrete use are available. Diamond

blades for concrete cutting can also be used.

Aclosed,2-sidedtype1cuttingwheelguard

is included with this tool and is re quired when

using cutting wheels. Fail ure to use proper

flange and guard can re sult in injury resulting

from wheel breakage and wheel contact. See

pages10and11formoreinformation.

MOUNTING CLOSED (TYPE 1) GUARD

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

1. Opentheguardlatch(10),andalignthe

arrow on the guard (9) with the arrow on

the hub (11). This will align the lugs with

slots on the gear case cover. Position

the guard facing backward.

2. Pushtheguarddownuntiltheguardlug

engages and rotates freely in the groove

on the gear case hub.

3. Rotate guard (9) into desired working position.

The guard body should be positioned

between the spindle and the operator to

provide maximum operator protection.

Close the guard latch to secure the guard

on the gear case cover. You should be

unable to rotate the guard by hand when

the latch is in closed position. Do not

operate grinder with a loose guard or

clamp lever in open position.

5. Toremovetheguard,opentheguard

latch, rotate the guard so that the arrows

are aligned and pull up on the guard.

NOTE: The guard is pre-adjusted to

the

dia met er of the gear case hub at the factory.

If, after a period of time, the guard becomes

loose,tightentheadjustingscrew(12)with

the clamp lever in the closed position with

guard installed on the tool.

Do not tighten adjusting screw with clamp

lever in open position. Undetectable damage

to guard or mounting hub may result.

MOUNTING CUTTING WHEELS

Turn off tool and remove battery before

making any adjustments or removing or

installing attachments or accessories.

Matching diameter backing flange and

threaded clamp nut (included with tool)

must be used for cutting wheels.

1. Place the unthreaded backing flange

on spindle with the raised section

(pilot) facing up. The raised section

(pilot) on the backing flange will be

against the wheel when the wheel is

installed.

2. Placethewheelonthebackingflange,

centering the wheel on the raised

section (pilot).

3. Install the threaded clamp nut with the

raised section (pilot) facing away from

the wheel.

4. Depress the spindle lock button and

tighten clamp nut with included wrench.

5. Toremovethewheel,depressthe

spindle lock button and loosen the

threaded clamp nut with included wrench.

USING CUTTING WHEELS

Do not use edge grinding/cutting wheels for

surface grinding applications because these

wheels are not designed for side pressures

encountered with surface grinding. Wheel

breakage and injury may result.

1. Allow tool to reach full speed before

touching tool to work surface.

2. Applyminimumpressuretowork

surface, allowing tool to operate at high

speed. Cutting rate is greatest when the

tool operates at high speed.

3. Once a cut is begun and a notch is

established in the workpiece, do not

change the angle of the cut. Changing

the angle will cause the wheel to bend

and may cause wheel breakage.

4. Remove the tool from work surface

before turning tool off. Allow the tool to

stop rotating before setting it down.

MAINTENANCE

CLEANING

Blowing dust and grit out of the motor

housing using compressed air is a necessary

maintenance procedure. Dust and grit from

metal grinding often accumulate on interior

surfaces and could create an electrical

shock hazard if not cleaned out.

•Alwayshandleaccessorieswithcare

when mounting or removing.

•Thebeststorageplaceforaccessoriesis

one that is cool and dry away from direct

sunlight and excess heat or cold.

WARNING: ALWAYS use safety

glasses. Everyday eyeglasses are NOT

safety glasses. Also use face or dust mask

if cutting operation is dusty. ALWAYS

WEAR CERTIFIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CSA Z94.3),

•ANSIS12.6(S3.19)hearingprotection,

•NIOSH/OSHA/MSHArespiratoryprotection.

Use only mild soap and a damp cloth to clean

the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

LUBRICATION

Porter Cable tools are properly lubricated

at the factory and are ready for use. Tools

should be lubricated regularly every year

depending on usage. (Tools used on heavy

duty jobs and tools exposed to heat may

require more frequent lubrication.) This

lubrication should be attempted only by

trained power tool repairperson’s such as

those at Porter Cable service centers or in

other qualified service personnel.

REPLACEMENT PARTS

Use only identical replacement parts. For a

parts list or to order parts, visit our service

website at www.portercableservicenet.com.

You can also order parts from your nearest

Porter Cable Factory Service Center or

Porter Cable Authorized Warranty Service

Center. Or, you can call our Customer Care

Centerat(888)848-5175.

ACCESSORIES

WARNING:

Since accessories, other

than those offered by Porter Cable, have

not been tested with this product, use of

such accessories with this tool could be

hazardous. To reduce the risk of injury, only

Porter Cable recommended accessories

should be used with this product.

A complete line of accessories is available

from your Porter Cable Factory Service

Center or a Porter Cable Authorized

Warranty Service Center. Please visit our

Web Site www.portercable.com for a catalog

or for the name of your nearest supplier.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery

Recycling Corporation) Seal on the

lithium-ion battery (or battery pack)

indicates that the costs to recycle the battery

(or battery pack) at the end of its useful life

have already been paid by PORTER-CABLE . In

some areas, it is illegal to place spent lithium-

ion batteries in the trash or municipal solid

waste stream and the RBRC program provides

an environmentally conscious alternative.

RBRC in cooperation with PORTER-CABLE

and other battery users, has established

programs in the United States and Canada

to facilitate the collection of spent lithium-ion

batteries. Help protect our environment and

conserve natural resources by returning the

tool to an authorized PORTER-CABLE service

center for recycling. You may also contact

your local recycling center for information on

where to drop off the spent battery, or call

1-800-8-BATTERY.

This Class B digital apparatus complies with

CanadianICES-003.Thisdevicecomplieswith

part15oftheFCCrules.Operationissubject

to the following two conditions: (1) This device

may not cause harmful interference, and (

2)thisdevicemustacceptanyinterference

received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested

and found to comply with the limits for Class

Bdigitaldevice,pursuanttopart15ofthe

FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed and

used in accordance with the instructions, may

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encouraged

to try to correct the interference by one or more

of the following measures:

 •Reorientorrelocatethereceivingantenna.

 •Increasetheseparationbetweenthe

equipment and the receiver.

 •Connecttheequipmentintoanoutletona

circuit different from that to which the receiver

is connected.

 •Consultthedealeroranexperiencedradio/

TV technician for help.

SERVICE AND REPAIRS

All quality tools will eventually require servicing

and/or replacement of parts. For information

about Porter Cable, its factory service centers

or authorized warranty service centers, visit

our website at www.portercable.com or call

ourCustomerCareCenterat(888)848-5175.

All repairs made by our service centers are

fully guaranteed against defective material and

workmanship. We cannot guarantee repairs

made or attempted by others.

You can also write to us for information at

PORTER CABLE,4825Highway45North,

Jackson,Tennessee38305-Attention:Product

Service. Be sure to include all of the information

shown on the nameplate of your tool (model

number, type, serial number, etc.).

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace,

without charge, any defects due to faulty

materials or workmanship for three years

from the date of purchase for tools (two

years for batteries). This warranty does not

cover part failure due to normal wear or

tool abuse. For further detail of warranty

coverage and warranty repair information,

visit www.portercable.com or call (888)

848-5175.Thiswarrantydoesnotapply

to accessories or damage caused where

repairs have been made or attempted by

others. This warranty gives you specific

legal rights and you may have other rights

which vary in certain states or provinces.

In addition to the warranty, PORTER-

CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE

will maintain the tool and replace worn

parts caused by normal use, for free, any

time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If

you are not completely satisfied with the

performance of your PORTER-CABLE

Power Tool for any reason, you can return it

within90daysfromthedateofpurchasewith

a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not

apply to products sold in Latin America.

For products sold in Latin America, see

country specific warranty information

contained in the packaging, call the local

company or see website for warranty

information.

To register your tool for warranty service

visit our website at www.portercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are

missing,call(888)848-5175forafreereplacement.

4825 Highway 45 North, Jackson, TN 38305

(888)848-5175

www.portercable.com

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION

•Lightwillnotilluminate •Batterypacknotinstalledproperly. •Checkbatterypack

installation.

    •Batterypacknotcharged.  •Checkbatterypack

charging requirements.

•Batterypackwillnotcharge.•Batterypacknotinsertedintocharger.•Insertbatterypackinto

charger until LED illuminates.

    •Chargernotpluggedin.  •Plugchargerintoa

working outlet. Refer to

“Important Charging Notes”

for more details.

    •Surroundingairtemperature•Movechargerandbattery

too hot or too cold. pack to a surrounding air

temperature of above

       40degreesF(4,5°C)or

        below105degreesF

        (+40,5°C).

•Unitshutsoffabruptly. •Batterypackhasreachedits•Allowbatterypacktocool

maximum thermal limit. down.

  •Outofcharge.(To •Placeonchargerand

maximize the life of the allow to charge.

battery pack it is designed

to shutoff abruptly when

the charge is depleted.)

For assistance with your product, visit our website at www.portercable.com for a list of

servicecenters,orcallthePORTER-CABLECustomerCareCenterat(888)848-5175.

AVERTISSEMENTS DE

SÉCURITÉ GÉNÉRAUX POUR

LES OUTILS ÉLECTRIQUES

AVERTISSEMENT :

Lire tous les

avertissements de sécurité et

toutes les directives. Le non-

respect des avertissements et des

directives pourrait se solder par un

choc électrique, un incendie et/ou

une blessure grave.

Conserver tous les avertissements

et toutes les directives pour un

usage ultérieur.

Le terme «outil électrique» cité dans

les avertissements se rapporte à votre

outil électrique à alimentation sur

secteur (avec fil) ou par piles (sans fil).

1) Sécurité du lieu de travail

a) Tenir la zone de travail propre et

bien éclairée. Les endroits sombres

sont souvent des causes d’accidents.

b) Ne pas faire fonctionner d’outils

électriques dans un milieu

déflagrant, soit en présence de

liquides inflammables, de gaz ou

de poussière. Les outils électriques

produisent des étincelles qui peuvent

enflammer la poussière ou les vapeurs.

c) Éloigner les enfants et les curieux au

moment d’utiliser un outil électrique.

Une distraction pourrait vous en faire

perdre la maîtrise.

2) Sécurité en matière d’électricité

a) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais

modifier la fiche en aucune façon. Ne

jamais utiliser de fiche d’adaptation

avec un outil électrique mis à la terre.

Le risque de choc électrique sera réduit

par l’utilisation de fiches non modifiées

correspondant à la prise.

Éviter tout contact physique avec

des surfaces mises à la terre comme

des tuyaux, des radiateurs, des

cuisinières et des réfrigérateurs. Le

risque de choc électrique est plus élevé

si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques

à la pluie ou à d’autres conditions où

il pourrait être mouillé. La pénétration

de l’eau dans un outil électrique

augmente le risque de choc électrique.

d) Ne pas utiliser abusivement le cordon

d’alimentation. Ne jamais utiliser

le cordon pour transporter, tirer ou

débrancher un outil électrique. Tenir

le cordon éloigné de la chaleur, de

l’huile, des bords tranchants ou

des pièces mobiles. Les cordons

endommagés ou emmêlés augmentent

les risques de choc électrique.

e) Pour l’utilisation d’un outil électrique

à l’extérieur, se servir d’une rallonge

convenant à une telle utilisation.

L’utilisation d’une rallonge conçue pour

l’extérieur réduit les risques de choc

électrique.

f) S’il est impossible d’éviter

l’utilisation d’un outil électrique

dans un endroit humide, brancher

l’outil dans une prise ou sur un

circuit d’alimentation dotés d’un

disjoncteur de fuite à la terre (GFCI).

L’utilisation de ce type de disjoncteur

réduit les risques de choc électrique.

3) Sécurité personnelle

a) Être vigilant, surveiller le travail

effectué et faire preuve de jugement

lorsqu’un outil électrique est utilisé.

Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence

de drogues, d’alcool ou de

médicaments. Un simple moment

d’inattention en utilisant un outil

électrique peut entraîner des blessures

corporelles graves.

Utiliser des équipements de

protection individuelle. Toujours

porter une protection oculaire.

L’utilisation d’équipements de protection

comme un masque antipoussière, des

chaussures antidérapantes, un casque

de sécurité ou des protecteurs auditifs

LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS

est important que vous lisiez et compreniez ce mode d’emploi. Les informations qu’il

contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les

symboles ci-dessous servent à vous aider à reconnaître cette information.

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée,

causera la mort ou des graves blessures.

AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, pourrait causer la mort ou de graves blessures.

MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle

n’est pas évitée, pourrait causer des blessures mineures ou modérées.

AVIS : Utilisé sans le symbole d’alerte à la sécurité, indique une

situationvpotentiellement dangereuse qui, si elle n’est pas évitée, peut résulter en des

dommages à la propriété.

lorsque la situation le requiert réduira

les risques de blessures corporelles.

c) Empêcher les démarrages

intempestifs. S’assurer que

l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une

source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de

transporter l’outil. Transporter un outil

électrique alors que le doigt repose

sur l’interrupteur ou brancher un outil

électrique dont l’interrupteur est à la

position de marche risque de provoquer

un accident.

d) Retirer toute clé de réglage ou clé

standard avant de démarrer l’outil.

Une clé standard ou une clé de réglage

attachée à une partie pivotante peut

causer des blessures.

e) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela

permet de mieux maîtriser l’outil électrique

dans les situations imprévues.

f) S’habiller de manière appropriée.

Ne pas porter de vêtements amples

ni de bijoux. Garder les cheveux,

les vêtements et les gants à l’écart

des pièces mobiles. Les vêtements

amples, les bijoux ou les cheveux longs

risquent de rester coincés dans les

pièces mobiles.

g) Si des composants sont fournis

pour le raccordement de dispositifs

de dépoussiérage et de ramassage,

s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un

dispositif de dépoussiérage peut réduire

les dangers engendrés par les poussières.

4) Utilisation et entretien d’un outil électrique

a) Ne pas forcer un outil électrique.

Utiliser l’outil électrique approprié

à l’application. L’outil électrique

approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour

laquelle il a été conçu.

b) Ne pas utiliser un outil électrique

dont l’interrupteur est défectueux.

Tout outil électrique dont l’interrupteur

est défectueux est dangereux et doit

être réparé.

c) Débrancher la fiche du secteur ou le

bloc-piles de l’outil électrique avant

de faire tout réglage ou changement

d’accessoire, ou avant de ranger

l’outil électrique. Ces mesures

préventives réduisent les risques de

démarrage accidentel de l’outil électrique.

d) Ranger les outils électriques hors

de la portée des enfants, et ne

permettre à aucune personne n’étant

pas familière avec un outil électrique

(ou son manuel d’instruction)

d’utiliser ce dernier. Les outils

électriques deviennent dangereux entre

les mains d’utilisateurs inexpérimentés.

e) Entretenir les outils électriques.

Vérifier les pièces mobiles pour

s’assurer qu’elles sont bien alignées

et tournent librement, qu’elles sont

en bon état et ne sont affectées par

aucun trouble susceptible de nuire

au bon fonctionnement de l’outil

électrique. En cas de dommage,

faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup

d’accidents sont causés par des outils

électriques mal entretenus.

f) S’assurer que les outils de coupe

sont aiguisés et propres. Les outils

de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer

et sont plus faciles à contrôler.

g) Utiliser l’outil électrique, les

accessoires, les forets, etc.

conformément aux présentes

directives en tenant compte des

conditions de travail et du travail

à effectuer. L’utilisation d’un outil

électrique pour toute opération autre

que celle pour laquelle il a été conçu

est dangereuse.

5) Utilisation et entretien du bloc-piles

Ne recharger l’outil qu’au moyen du

chargeur précisé par le fabricant.

L’utilisation d’un chargeur qui convient à

un type de bloc-piles risque de provoquer

un incendie s’il est utilisé avec un autre

type de bloc-piles.

b) Utiliser les outils électriques

uniquement avec les blocs-piles

conçus à cet effet. L’utilisation de tout

autre bloc-piles risque de causer des

blessures ou un incendie.

Lorsque le bloc-piles n’est pas

utilisé, le tenir éloigné des objets

métalliques, notamment des

trombones, de la monnaie, des clés,

des clous, des vis, etc., qui peuvent

établir une connexion entre les deux

bornes. Le court-circuit des bornes

du bloc-piles risque de provoquer des

étincelles, des brûlures ou un incendie.

d) En cas d’utilisation abusive, le

liquide peut gicler hors du bloc-

piles, éviter tout contact. Si un

contact accidentel se produit, laver

à grande eau. Si le liquide entre en

contact avec les yeux, obtenir des

soins médicaux. Le liquide qui gicle

hors du bloc-piles peut provoquer des

irritations ou des brûlures.

6) Réparation

a) Faire réparer l’outil électrique

par un réparateur professionnel

en n’utilisant que des pièces de

rechange identiques. Cela permettra

de maintenir une utilisation sécuritaire

de l’outil électrique.

La page charge ...

Porter Cable PCC761B Manuel utilisateur

Marque: Porter Cable

Modèle: PCC761B

Catégorie: Ponceuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Porter Cable PCC761B User manual
español: Porter Cable PCC761B Manual de usuario

Porter Cable PCC761B Manuel utilisateur

Porter Cable PCC761B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents