La Crosse Technology 308-179 Manuel utilisateur

Marque: La Crosse Technology

Modèle: 308-179

Catégorie: Réveils

Taper: Manuel utilisateur

Ce manuel convient également à

OMOTX141-AV2

Wireless Temperature Station

Model: 308-179 | Quick Setup Guide

The Wireless Temperature Station features manual set time, date,

alarm with snooze, indoor and outdoor temperature with high and

low outdoor temperature alarms. Large temperature digits provide

temperature at a glance. Wireless transmission range of over 200

feet (60 meters) in open air, from transmitter to temperature station.

SETUP INSTRUCTIONS STEP BY STEP

STEP 1:

• Remove battery cover from the Temperature Station. Slide tab

down and pull out to remove the

battery cover.

• Insert 2 NEW AA batteries (not

included) into the back of the

Temperature Station. Observe the

correct polarity (see marking inside

the battery compartment).

• The Temperature Station will light up

and show, indoor temperature.

• Do Not Mix Old and New Batteries

• Do Not Mix Alkaline, Standard, Lithium or Rechargeable

Batteries

STEP 2:

• Ensure that the transmitter is within 10 feet of the

Temperature Station.

• Remove battery cover from TX141-AV2 transmitter:

Slide the battery cover down and lift off the front of the

transmitter.

• Insert 2 NEW AA batteries into the transmitter.

Observe the correct polarity.

• Within 3 minutes the Temperature Station will show readings in

the outdoor temperature area on the LCD.

Note: Allow the Temperature Station and the transmitter to stay

within 10 feet of each other for the first 15 minutes of set up.

TRANSMITTER SIGNAL STRENGTH

z After the batteries are inserted, the weather station will search

for the outdoor temperature transmitter for 3 minutes.

z The antenna symbol will flash during reception, and

temperature display will be dashes “---“.

z The antenna symbol will scroll during signal synchronization.

z If synchronization fails once, the antenna will lose one bar.

z If synchronization fails twice, the antenna will lose two bars.

z If reception continuously fails to receive 5 times, the antenna

symbol will be shown as

z The antenna will show full display with successful RF

(radio frequency) reception.

TROUBLESHOOTING

z If the outdoor temperature is not displayed after three minutes,

hold the SENSOR SEARCH button on the temperature station

for three seconds to search for outdoor transmitter.

z Next remove the battery cover from the

TX141-Av2 transmitter then press the TX

button to send a signal.

z If it still does not receive the outdoor

temperature, remove the batteries from both the temperature

station and the transmitter for 15 minutes repeat setup

instructions from step 1.

z The maximum transmitting range in open air is over 200-feet (60

meters). Obstacles such as walls, windows, stucco, concrete,

and large metal objects can reduce the range.

TIME/DATE

The TIME/DATE button moves through the

program menu and confirm settings.

The UP arrow (on back) will increase a selected

value.

The DOWN arrow (on back) will decrease a

selected value.

SET TIME/DATE

Hold the TIME/DATE button for three seconds to enter time set

mode.

z YEAR: The Year will flash, use the ARROW buttons to choose

the year, and press the TIME/DATE button to confirm and move

to the month.

z MONTH: The Month will flash, use the ARROW buttons to

choose the month, and press the TIME/DATE button to confirm

and move to the date.

z DATE: The Date will flash; use the ARROW buttons to choose

the date. Press the TIME/DATE button to confirm and move to

12/24 hour time format.

z 12/24-HOUR: The time format 12H will flash, use the ARROW

buttons to choose 12-hour or 24-hour time format and press the

TIME/DATE button to confirm and move to hour.

z HOUR: The Hour will flash, use the ARROW buttons to choose

the hour, and press the TIME/DATE button to confirm and move

to minutes.

z MINUTES: The Minutes will flash, use the ARROW buttons to

choose the minutes, and press the TIME/DATE button to

confirm and move to Fahrenheit/Celsius.

z FAHRENHEIT/CELSIUS: °F or °C will flash. Use the ARROW

buttons to select Fahrenheit or Celsius. Press and release the

TIME/DATE button to confirm and exit the program menu.

Note: When no buttons are pressed for ten seconds, the

Temperature Station will save the last change and default back to

normal time and temperature display mode.

TIME ALARM

The TIME ALARM button moves through alarm set

mode and confirms settings.

The UP arrow (on back) will increase a value.

The DOWN arrow (on back) will decrease a value.

SET ALARM

From normal time and temperature display mode,

press and

release the TIME ALARM button once to show alarm time. Hold

the TIME ALARM button for three seconds to enter alarm set

mode.

z HOUR: The Hour will flash, use the ARROW buttons to set the

hour, and press TIME ALARM button to confirm. Then press the

TIME ALARM button again switch to minute setting.

z MINUTES: The Minutes will flash, use the ARROW buttons to

set the minutes, and press TIME ALARM button to confirm.

z Press the TIME/DATE button to return to normal mode

Note: When no buttons are pressed for ten seconds, the

Temperature Station will save the last change and default back to

normal time and temperature display mode,.

ACTIVATE/DEACTIVATE ALARM

z From normal time and temperature display mode, press and

release the TIME ALARM button once to show alarm time.

z Press and release the TIME ALARM button repeatedly to turn

the alarm ON/OFF. The alarm icon

appears when alarm is

activated.

SNOOZE

When the alarm sounds press the TIME ALARM button to snooze

the alarm for 10 minutes. The snooze option can be repeated three

times.

Note: while the alarm sounds press any button except the TIME

ALARM button to turn the alarm off.

LOW BATTERY

• When this low battery icon

appears in the indoor (IN) reading

section, replace the batteries in the weather station.

• When this low battery icon

appears in the outdoor (OUT)

readings section, replace the batteries in the outdoor transmitter.

MIN/MAX TEMPERATURE

The Temperature Station will show the daily minimum and

maximum temperatures each day starting at midnight (12:00 AM).

The Temperature Station automatically resets the min/max

temperatures at midnight (12:00 AM).

• View MIN data: Press and release the MIN button to

view the minimum Indoor and Outdoor

Temperatures.

• Reset MIN data: Hold the MIN button for 3 seconds

and the Indoor and all Outdoor Minimum Temperatures will be

reset to current temperatures.

• View MAX data: Press and release the MAX button

to view the maximum Indoor and Outdoor

Temperatures.

• Reset MAX data: Hold the MAX button for 3 seconds

and the Indoor and all Outdoor Maximum

Temperatures will be reset to current temperatures.

Note:

When no buttons are pressed for ten seconds,

the weather station will return to display the current temperature.

TEMPERATURE ALERTS

Alert values are set when they flash in the outdoor temperature

area. Temperature alerts are turned on or off in the Temperature

Alert box.

One or all the temperature alerts may be set.

Range for outdoor temperature alert:

-40°F to 140°F (-40°C to 60°C)

SELECT TEMPERATURE ALERT VALUES

Hold the TEMP ALERTS button for three

seconds, until the temperature station beeps,

to enter alert setting.

z OUTDOOR HI alert will flash where the outdoor

temperature shows. Press the ARROW buttons to set the

alert value, and press the TEMP ALERTS button to confirm.

Then press the TEMP ALERTS button again switch to

OUTDOOR LOW setting.

z OUTDOOR LO alert will flash where the outdoor

temperature shows. Press the ARROW buttons to set the

alert value, and press the TEMP ALERTS button to confirm

and exit.

Note: After selecting temperature alert values use the next step to

turn individual alerts ON or OFF.

TEMPERATURE ALERTS ON/OFF

From normal time and temperature display mode,

press and

release the TEMP ALERTS button to toggle between:

o Outdoor HI

o Outdoor LO

z Press the UP ARROW button (Alert ON) to turn the selected

alert ON. The alert icon

appears when alarm is activated.

z Press the DOWN ARROW button (Alert OFF) to turn the

selected alert OFF.

Note: When no temperature alerts are set the

Temperature Alert area will show OFF.

TEMPERATURE ALERT SOUNDS

z When temperature alert is ringing, corresponding alert

icon will flash.

z The alert will ring for five seconds every minute, until the

temperature is out of alert range.

z Press any button to stop alert. The alert icon will still show.

z Turn alert OFF: In normal mode, press and release the TEMP

ALERTS button to select the alert to turn off. With HI or LO alert

selected, press the DOWN ARROW button to turn that alert OFF.

TEMPERATURE TREND ARROWS

The indoor and outdoor temperature trend arrows will update every

30 minutes or less. These trends represent temperature changes

over the past three hours.

UP: Temperature rising more than 2°F/1°C in the past

three hours

RIGHT: Temperature has not changed more than

2°F/1°C in the past three hours.

DOWN: Temperature falling more than 2°F/1°C in the

past three hours

POSITION THE TEMPERATURE STATION

Choose a location for the Temperature Station that is within range

(200 feet, 60 meters) of the outdoor transmitter. The

Temperature Station has a built in base to sit on a table

or desk.

• Choose a location 6 feet or more from electronics

such as cordless phones, gaming systems,

televisions, microwaves, routers, baby monitors, etc.,

which can prevent signal reception.

• Be aware of electrical wires and plumbing within a

wall.

• Best reception is achieved when the front or the back

of the Temperature Station is facing the outdoor transmitter.

This allows a larger portion of the antenna to receive a signal.

POSITION THE WIRELESS OUTDOOR TRANSMITTER

Once the Temperature Station shows the outdoor temperature,

place it and the transmitter in the desired locations and wait

approximately 1-hour before permanently mounting the transmitter

to ensure that there is proper reception. The transmitter should be

mounted vertically, in a shaded, protected area, at least 6 feet from

the ground to avoid damage and ensure accurate readings. The

transmitter is water resistant, not waterproof and should not be

placed anywhere it will become submerged in water or subject to

standing water or snow.

Choose a location for the transmitter that is within range of the

Temperature Station and under an overhang for

accuracy.

Option 1:

• Install one mounting screw (not included) into a

wall leaving approximately ½ of an inch (12.7mm)

extended.

• Place the transmitter onto the screw, using the

hanging hole on the backside.

• Gently pull the transmitter down to lock the screw

into place.

Option 2:

• Insert the mounting screw (not included) through the front of the

transmitter and into the wall.

• Tighten the screw to snug (do not over tighten).

To achieve a true temperature reading, mount where direct

sunlight cannot reach the outdoor transmitter. Mount the outdoor

transmitter on a North-facing wall or in any well shaded area.

Under an eave or deck rail work well. The maximum transmitting

range in open air is over 200-feet (60 meters). Obstacles such as

walls, windows, stucco, concrete, and large metal objects can

reduce the range. Place the transmitter at least 6 feet in the air to

improve signal transmission.

CARE AND MAINTENANCE

• Do Not Mix Old and New Batteries

• Do Not Mix Alkaline, Standard, Lithium or Rechargeable

Batteries

• Do not expose the weather station to extreme temperatures,

vibration or shock.

• Keep weather station dry.

• Clean weather station with a soft damp cloth. Do not use

solvents or scouring agents.

• The weather station is not a toy. Keep it out of reach of children.

• The weather station is not to be used for medical purpose or for

public information; it is for home use only.

• The specifications of this weather station may change without

prior notice.

• Improper use or unauthorized opening of housing will void the

warranty.

• If the weather station does not work properly, change the

batteries.

SPECIFICATIONS

Indoor:

Temperature Range: +32°F to +122°F (0°C to 50°C)

Interval: About every 30 seconds

Outdoor:

Temperature Range: -40°F to 140°F (-40°C to 60°C)

Distance: Over 300 ft. (100 meters)

RF 433MHz (open air)

Interval: About every 50 seconds

Power:

Temperature Station: 2-AA, IEC, LR6 batteries

(not included)

TX141-Av2 Transmitter: 2-AA, IEC, LR6 batteries

(not included)

Battery Life:

TX141-Av2 Transmitter

Battery Life: Battery life is over 24 months when

using reputable Alkaline battery

brands.

Temperature Station

Battery Life: Battery life is over 12 months when

using reputable Alkaline battery

brands.

Dimensions:

Temperature Station: 4.27”L x 1.48”W x 3.88”H

(108 x 38 x 99 mm)

TX141-Av2

Transmitter: 1.57" L x 0.79" W x 5.12" H

(40 x 20 x 130 mm)

WARRANTY INFORMATION

La Crosse Technology, Ltd provides a 1-year limited warranty on

this product against manufacturing defects in materials and

workmanship.

This limited warranty begins on the original date of purchase, is

valid only on products purchased and used in North America and

only to the original purchaser of this product. To receive warranty

service, the purchaser must contact La Crosse Technology, Ltd for

problem determination and service procedures. Warranty service

can only be performed by a La Crosse Technology, Ltd authorized

service center. The original dated bill of sale must be presented

upon request as proof of purchase to La Crosse Technology, Ltd

or La Crosse Technology, Ltd’s authorized service center.

La Crosse Technology, Ltd will repair or replace this product, at

our option and at no charge as stipulated herein, with new or

reconditioned parts or products if found to be defective during the

limited warranty period specified above. All replaced parts and

products become the property of La Crosse Technology, Ltd and

must be returned to La Crosse Technology, Ltd. Replacement

parts and products assume the remaining original warranty, or

ninety (90) days, whichever is longer. La Crosse Technology, Ltd

will pay all expenses for labor and materials for all repairs covered

by this warranty. If necessary repairs are not covered by this

warranty, or if a product is examined which is not in need or repair,

you will be charged for the repairs or examination. The owner

must pay any shipping charges incurred in getting your La Crosse

Technology, Ltd product to a La Crosse Technology, Ltd

authorized service center. La Crosse Technology, Ltd will pay

ground return shipping charges to the owner of the product to a

USA address only.

Your La Crosse Technology, Ltd warranty covers all defects in

material and workmanship with the following specified exceptions:

(1) damage caused by accident, unreasonable use or neglect

(including the lack of reasonable and necessary maintenance); (2)

damage occurring during shipment (claims must be presented to

the carrier); (3) damage to, or deterioration of, any accessory or

decorative surface; (4) damage resulting from failure to follow

instructions contained in your owner’s manual; (5) damage

resulting from the performance of repairs or alterations by

someone other than an authorized La Crosse Technology, Ltd

authorized service center; (6) units used for other than home use

(7) applications and uses that this product was not intended or (8)

the products inability to receive a signal due to any source of

interference.. This warranty covers only actual defects within the

product itself, and does not cover the cost of installation or removal

from a fixed installation, normal set-up or adjustments, claims

based on misrepresentation by the seller or performance variations

resulting from installation-related circumstances.

LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME

LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR

OTHER SIMILAR DAMAGES ASSOCIATED WITH THE

OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS

PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR

FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY.

KEEP OUT OF CHILDREN’S REACH.

This warranty gives you specific legal rights. You may also have

other rights specific to your State. Some States do not allow the

exclusion of consequential or incidental damages therefore the

above exclusion of limitation may not apply to you.

For warranty work, technical support, or information contact:

La Crosse Technology, Ltd

2817 Losey Blvd. S.

La Crosse, WI 54601

Contact Support: 608-782-1610

Product Registration:

www.lacrossetechnology.com/support/register

The complete instruction manual is available

at: www.lacrossetechnology.com/308-179

Protected under U.S. Patents:

5,978,738

6,076,044

6,597,990

FCC STATEMENT

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for

help.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This transmitter must not be

co-located or operating in conjunction with any other antenna or

transmitter.

Caution!

The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modifications to this

equipment. Such modifications could void the user authority to

operate the equipment.

form, even in excerpts, or duplicated or processed using electronic,

mechanical or chemical procedures without written permission of

the publisher.

This handbook may contain mistakes and printing errors. The

information in this handbook is regularly checked and corrections

made in the next issue. We accept no liability for technical

mistakes or printing errors, or their consequences.

All trademarks and patents are acknowledged.

IC RSS warning

This device complies with Industry Canada licence-exempt RSS

standard (s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device

must accept any interference,including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

Under Industry Canada regulations, this radio transmitter may only

operate using an antenna of a type and maximum (or lesser) gain

approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its

gain should be so chosen that, the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for successful

communication.

Conformément à la réglementation d'Industrie Canada, le présent

émetteur radio peut fonctionner avec une antenne d'un type et

d'un gain maximal (ou inférieur) approuvé pour l'émetteur par

Industrie Canada. Dans le but de réduire les risques de brouillage

radioélectrique à l'intention des autres utilisateurs, il faut choisir le

type d'antenne et son gain de sorte que la puissance isotrope

rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication satisfaisante.

This radio transmitter (identify the device by certification number,

or model number if Category II) has been approved by Industry

Canada to operate with the antenna types listed below with the

maximum permissible gain and required antenna impedance for

each antenna type indicated. Antenna types not included in this list,

having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro

de certification ou son numéro de modèle s'il fait partie du matériel

de catégorie I) a été approuvé par Industrie Canada pour

fonctionner avec les types d'antenne énumérés ci-dessous et

ayant un gain admissible maximal etl'impédance requise pour

chaque type d'antenne. Les types d'antenne non inclus dans cette

liste,

ou dont le gain est supérieur au gain maximal indiqué, sont

strictement interdits pour l'exploitation de l'émetteur.

IC Radiation Exposure Statement:

This equipment complies with IC RF radiation exposure limits set

forth for an uncontrolled environment. This transmitter must not be

co-located or operating in conjunction with any other antenna or

transmitter.

IC exposition aux radiations:

Cet équipement est conforme avec IC les limites d'exposition aux

rayonnements définies pour un contrôlé environnement.

Cet émetteur ne doit pas être co-localisés ou fonctionner en

conjonction avec une autre antenne ou émetteur.

Printed in China

La Crosse Technology 308-179 Manuel utilisateur

Marque: La Crosse Technology

Modèle: 308-179

Catégorie: Réveils

Taper: Manuel utilisateur

Ce manuel convient également à

OMOTX141-AV2

Télécharger le PDF

rapport

dans d''autres langues

English: La Crosse Technology 308-179 User manual

La Crosse Technology 308-179 Manuel utilisateur

Ce manuel convient également à

La Crosse Technology 308-179 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents