Introduction
What’s in the box
What you’ll need
●BH61 Wireless Alarm Hub
●A working internet connection
●A smartphone or laptop
●A #2 Phillips driver (screwdriver or power drill)
●¼ inch (6.35mm) drill bit if using wall anchors
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
BR33 Wireless Panic Button
3
Mount plate
(Attached to button)
1 T10 Torx wrench 2 Wall mount screws &
2 wall anchors
1 VHB adhesive
mounting strip
1 CR123A battery
(Installed)
Mounting positions
Above surface Side of surface Below surface
Introduction
Sensor overview
LED Behavior
LED off
Default state
(check status in Verkada Command)
LED blinking fast
Panic button pressed, but signal has not
been received by hub
LED on for 1 minute
Panic button pressed and signal received by
hub
LED blinks 3 times, every 2 minutes
Low battery
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
LED
4
Button
Mount Plate
Connect
Please note: Add your BH61 Wireless Alarm
Hub to Command before setting up your
Wireless Panic Button.
●To register your product, please
proceed to: verkada.com/start
Installation
Mounting with screws
Unscrew captive T10 security screw to
remove Button Unit from Mount Plate.
Drill holes in mounting surface.
Secure Mount Plate to mounting surface,
using the 2 screws and 2 wall anchors
(included).
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
Remove pull tab between battery and
battery contacts in Button Unit.
Insert Button Unit into Mount Plate until you
hear a click.
Secure Button Unit in Mount Plate with the
captive T10 security screw and T10
screwdriver.
Installation
Mounting with VHB
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
6
Unscrew captive T10 security screw to
remove Button Unit from Mount Plate.
Peel protective film from one side of the
adhesive mounting strip. Adhere to back
side of device.
Peel the remaining protective film and
adhere to the mounting surface.
Remove pull tab between battery and
battery contacts in Button Unit.
Insert Button Unit into Mount Plate until you
hear a click.
Secure Button Unit in Mount Plate with the
captive T10 security screw and T10
screwdriver.
Appendix
BR33 Compliance
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
7
FCC
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party
responsible for compliance may void the user’s authority to operate his equipment. (Example – use only
shielded interface cables when connecting to computer or peripheral devices)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
IC
Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance
with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la
conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la
conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou
émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
things don’t work right, or you need assistance, please contact us
immediately.
verkada.com/support
Sincerely, The Verkada Team
8
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Verkada BR33 Installation guide
Documents connexes
-
Verkada BR32 Guide d'installation
-
Verkada Br35 Guide d'installation
-
-
-
-
-
-
Verkada AD33 Guide d'installation
-
Autres documents
-
Sonim XPand Manuel utilisateur
-
Sony PSP-1001 Manuel utilisateur
-
-
Watchguard Firebox T10 Hardware Guide
-
Sony DUALSHOCK®4 Controller Le manuel du propriétaire
-
-
-
-
Kensington Expert Mouse Manuel utilisateur
-
Tile T1501S Mode d'emploi