LG LCE3610SBE Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

OWNER'S MANUAL
CERAMIC-GLASS
RADIANT COOKTOP
Read this owner's manual thoroughly before operating the
appliance and keep it handy for reference at all times.
ENGLISH
LCE3010SBE LCE3610SBE
MFL54169116
Rev.00_101823
www.lg.com
Copyright © 2023 LG Electronics Inc. All Rights Reserved.
Scan to see the online manual.
en-us_main.book.book Page 1 Tuesday, October 17, 2023 1:22 PM
TABLE OF CONTENTS
2
3 IMPORTANT SAFETY
INSTRUCTIONS
3 READ ALL INSTRUCTIONS BEFORE USE
3 WARNING STATEMENTS
6 CAUTION STATEMENTS
8 PRODUCT OVERVIEW
8 Product Features
9 INSTALLATION
9 Before Installing
13 Installing the Cooktop
18 OPERATION
18 Cookware
20 Control Panel
25 MAINTENANCE
25 Care and Cleaning
27 TROUBLESHOOTING
27 Before Calling for Service
29 LIMITED WARRANTY
29 USA
33 CANADA
en-us_main.book.book Page 2 Tuesday, October 17, 2023 1:22 PM
3IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
Download this owner's manual at http://www.lg.com
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING STATEMENTS
WARNING
To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this
product, follow basic precautions, including the following:
Installation
Be sure your appliance is properly installed and grounded by a qualified technician in accordance with
the National Electrical Code ANSI/NFPA No. 70, latest edition in the United States, and all local code
requirements. Install only per installation instructions.
The safety aspects of this appliance comply with accepted technical standards.
Never modify or alter the construction of an appliance such as removal of panels, wire covers or any
other permanent part of the product.
Remove all tape and packaging wrap before using the appliance. Destroy the carton and plastic bags
after unpacking the appliance. Never allow children to play with packaging material.
The installation and connection of the new appliance must only be carried out by qualified personnel.
Operation
Know how to disconnect the electrical power to the appliance at the circuit breaker or fuse box in case of
an emergency. Mark the breaker or fuse for ease of identification and swift action if necessary.
Never use your appliance for warming or heating a room.
DO NOT touch cooking zones or areas near these surfaces. Cooking zones may be hot from residual heat
even though they are dark in color. Areas near the cooking zones may become hot enough to cause
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
en-us_main.book.book Page 3 Tuesday, October 17, 2023 1:22 PM
4IMPORTANT SAFETY INSTRUCTIONS
burns. During and after use, do not touch, or let clothing or other flammable materials touch these areas
until they have had sufficient time to cool.
Never wear loose fitting or hanging garments while using this appliance.
Always turn off all controls when cooking is completed.
Do not use water or flour on grease fires. Smother the fire with a pan lid, or use baking soda or a dry
chemical or foam-type extinguisher.
Use only dry pot holders. Moist or damp pot holders on hot surfaces may result in burns from steam. Do
not let pot holders touch hot surface units. Do not use a towel or other bulky cloth instead of a pot
holder.
Do not heat unopened food containers. A buildup of pressure may cause the container to burst and
result in injury.
Flammable materials should not be stored near or on the cooking surface. This includes paper, plastic
and cloth items, such as cookbooks, plasticware and towels, as well as flammable liquids. Do not store
explosives, such as aerosol cans, on or near the appliance. Flammable materials may explode and result
in fire or property damage.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
Never place combustible items on the cooktop.
Never keep any combustible items or aerosol cans in a drawer located under the cooktop.
When heating fat or grease, watch it closely. Fat or grease may catch fire if allowed to become too hot.
Overheated fats and oils catch fire quickly. You should supervise cooking when preparing foods in fat or
oil.
Use a deep fat thermometer, if possible, to prevent overheating fat beyond the smoking point.
If the surface is cracked, switch off the appliance to avoid the possibility of electric shock. Do not reuse
your cooktop until the glass surface has been replaced.
When using the cooktop, never use aluminum foil, products wrapped in aluminum foil, or deep-frozen
food in aluminum cookware.
This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Accessible parts may become hot during use. Young children should be kept away.
Items of interest to children should not be stored in cabinets above a cooktop or on the backsplash of a
cooktop – children climbing on the cooktop to reach items could be seriously injured.
Children should not be left alone or unattended in the area where an appliance is in use. They should
never be allowed to sit or stand on any part of the appliance.
Take care when plugging in electric appliances near the cooktop. Cords must not come into contact with
the hot surface. Doing so could cause damage to the cooktop and cable insulation.
After use, switch off the cooktop element by its control and do not rely on the pan detector.
Avoid placing metal objects such as knives, forks, spoons and lids on the cooking surface areas. Metal
objects can become hot and cause burns.
Do not place any object on or near the display area in order to prevent accidental activation of the
cooktop controls.
Cookware handles should be turned inward and not extend over adjacent surface units. To reduce the
risk of burns, ignition of flammable materials, and spillage due to unintentional contact with the
cookware, the handles of cookware should be positioned so that they are turned inward, and do not
extend over adjacent surface units.
Never leave prepared food on the cooking zones. Boilovers cause smoking and greasy spillovers that
may ignite, or a pan that has boiled dry may melt or become damaged.
en-us_main.book.book Page 4 Tuesday, October 17, 2023 1:22 PM
5IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
Do not use aluminum foil to line any part of the cooktop. Only use aluminum foil as recommended after
the cooking process, if used as a cover to be placed over the food. Any other use of aluminum foil may
result in the risk of electric shock, fire or short circuit.
Do not clean or operate a broken cooktop. If the cooktop breaks, cleaning solutions and spillovers may
penetrate the broken cooktop and create a risk of electric shock. Contact a qualified technician
immediately.
Never leave surface units unattended at high heat settings. Boilover causes smoking and greasy
spillovers that may ignite.
Always turn off all controls when cooking is completed.
Keep pets away from the product to avoid risk of fire or burns. Do not allow pets to climb on the product
even when it is not in operation.
Liquids such as water, coffee or tea are able to be overheated beyond the boiling point without
appearing to be boiling, due to surface tension of the liquid. Visible bubbling or boiling is not always
present when the container is removed from the cooktop. This could result in very hot liquids suddenly
boiling over when the container is disturbed or a spoon or other utensil is inserted into the liquid. To
reduce the risk of injury to persons:
- Do not overheat the liquid.
- Stir the liquid both before and halfway through heating it.
- Do not use straight-sided containers with narrow necks.
- After heating, allow the container to stand on the cooktop for a short time before moving the
container.
- Use extreme care when inserting a spoon or other utensil into the container after heating.
Do not use the cooktop as a work surface or storage space.
Do not operate the cooking zones with empty pots or pans.
Do not turn on the cooking zones with no pots or pans on the element.
The cooking process has to be supervised. A short term cooking process has to be supervised
continuously.
The appliance must not be installed behind a decorative door in order to avoid overheating.
Maintenance
Do not repair or replace any part of the appliance. All servicing should be done only by a qualified
technician to avoid the risk of personal injury and damage to the appliance.
Take care to avoid steam burns if using a wet sponge or cloth to wipe spills on a hot cooking area.
Wait for the cooktop to cool before using cooktop cleaners. Some cleaners can produce NOXIOUS
FUMES if applied to a hot surface.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
If your appliance malfunctions or fractures, switch off all cooking zones, and contact an LG Customer
Information Center for service.
Always keep the control panel clean and dry. Do not let liquids or grease remain on the cooktop display
area. Spilled or burnt-on foods can activate or deactivate the appliance. Clean the display area
thoroughly to resume normal operation of the appliance.
Clean the appliance regularly to keep all parts free of grease that could catch fire. Exhaust fan ventilation
hoods and grease filters should be kept clean. Do not allow grease to accumulate on the hood or filters.
Greasy deposits in the fan could catch fire. Refer to the hood manufacturer's instructions for cleaning.
en-us_main.book.book Page 5 Tuesday, October 17, 2023 1:22 PM
6IMPORTANT SAFETY INSTRUCTIONS
CAUTION STATEMENTS
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or
property when using this product, follow basic precautions, including the following:
Operation
This appliance may only be used for normal cooking and frying in the home. It is not designed for
commercial or industrial purposes.
Use proper pan sizes. This appliance is equipped with one or more surface units of different sizes.
Select cookware having flat bottoms large enough to cover the cooking zones.
Only certain types of glass, glass/ceramic, ceramic, earthenware, or other glazed cookware are suitable
for rangetop service without breaking due to the sudden change in temperature. Check the
manufacturer’s recommendations for cooktop use.
Do not place hot cookware on cold cooktop glass. This could cause the glass to break.
Do not slide pans across the cooktop surface. They may scratch the cooktop surface.
Do not let pans boil dry. This may cause permanent damage in the form of breakage, fusion, or marking
that can affect the ceramic-glass cooktop. (This type of damage is not covered by your warranty.)
Cook meat and poultry thoroughly, meat to at least an INTERNAL temperature of 160 and poultry to at
least an INTERNAL temperature of 180 . Cooking to these temperatures usually protects against food-
borne illnesses.
Prior to using the cooktop for the first time, apply the recommended cooktop cleaning cream to the
ceramic surface. Buff with a non-abrasive cloth or pad. This will make cleaning easier when the cooktop
gets soiled from cooking. The special cooktop cleaning cream leaves a protective finish on the glass to
help prevent scratches and abrasions.
Please be careful of the cooktop edges when moving pots and pans.
Ceramic glass is very tough, and impervious to sharp temperature changes, but is not unbreakable. It
can be damaged if hard or sharp objects fall on it.
Be very cautious if using pots made of cast iron, or other pots with rough edges or burrs. Moving these
can cause scratches on the glass.
Do not slide metal or glass across the cooktop surface.
Do not use cookware with any dirt buildup on the bottom.
Do not use cookware with rough or uneven bottoms. This cookware can mark and scratch the cooktop
surface.
Do not use the glass cooktop surface as a cutting board.
The appliance is not intended to be operated by means of an external timer or separate remote-control
system.
Maintenance
Always switch off the appliance before cleaning.
For safety reasons, do not clean the appliance with a steam jet or high-pressure cleaner.
Clean the cooktop in accordance with the maintenance and cleaning instructions in this manual.
Do not use harsh abrasive cleaners or rough metal scrapers to clean the cooktop glass since they can
scratch the surface, which may result in shattering of the glass.
Clean the cooktop cautiously. Do not use sponges or cloth to wipe spills on a hot cooking area. Use a
proper metal scraper.
en-us_main.book.book Page 6 Tuesday, October 17, 2023 1:22 PM
7IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
SAVE THESE INSTRUCTIONS
If sugar or a mixture containing sugar falls onto a hot cooking zone and melts, remove it with a metal
scraper immediately, while still hot. If left to cool down, it may damage the surface when removed. Use
caution and wear an oven mitt to avoid burns.
Keep meltable objects or materials away from the ceramic glass surface, for example, plastic utensils,
aluminum foil, or cooking wraps. If any materials or foodstuffs melt on the ceramic-glass surface, these
should be cleaned up immediately.
Use oven mitts to avoid burns when using a metal scraper on a hot cooking zone.
Refer to the Maintenance section for proper cleaning and maintenance of the cooktop.
Disposal of Old Appliances
To protect the environment, it is important that worn-out appliances are disposed of in the correct
manner.
The appliance must not be disposed of with household rubbish.
You can obtain information about collection dates or public refuse disposal sites from your local
government or waste collection service.
Before disposing of old appliances make them inoperable so they cannot be a source of danger. To do
this, have a qualified person disconnect the appliance from the house circuitry.
en-us_main.book.book Page 7 Tuesday, October 17, 2023 1:22 PM
8PRODUCT OVERVIEW
PRODUCT OVERVIEW
Product Features
Parts and Features
Throughout this manual, features and appearance
may vary from your model.
LCE3010SBE
LCE3610SBE
Accessories
aCooktop Cleaner (1 ea)
bNon-scratch Scouring Pad (1 ea)
cRetainer Brackets (2 ea)
dBolts (2 ea)
eType A Screws (2 ea)
Parts and Features
aSingle Cooking Zone 6 7/16" (163 mm)
bSingle Cooking Zone 8 3/4" (223 mm)
cSingle Cooking Zone 7 5/8" (193 mm)
dWarming Zone 6" (152 mm)
eDual Cooking Zone 9 15/16/6 (253 mm/152
mm)
fControl Panel
Parts and Features
aSingle Cooking Zone 6 7/16" (163 mm)
bDual Cooking Zone 8 3/4"/5" (223 mm/127
mm)
cTriple Cooking Zone 12 5/16"/9"/6" (313 mm/
229 mm/152 mm)
dWarming Zone 6" (152 mm)
eDual Cooking Zone 9 15/16"/6" (253 mm/152
mm)
fControl Panel
Parts and Features
Cleaner
en-us_main.book.book Page 8 Tuesday, October 17, 2023 1:22 PM
9INSTALLATION
ENGLISH
INSTALLATION
Before Installing
Before You Begin
Installation and service must be performed by a
qualified installer.
Important: Save these instructions for the local
electrical inspector’s use. Read and save these
instructions for future reference.
Read these instructions completely and carefully.
CAUTION
If storage is located under the cooktop, do not
use it to store flammable or heat-sensitive items
such as detergents, aerosols, cleaners, water,
food, or plastics.
NOTE
Installer:
Read all installation instructions before installing
the cooktop.
Remove all packing material before connecting
the electrical supply to the cooktop.
Observe all governing codes and ordinances.
Only certain cooktop models may be installed
over certain built-in electric oven models.
Be sure to leave these instructions with the
consumer.
NOTE
Consumer:
Keep the owner's manual and installation
instructions for future reference.
NOTE
This appliance must be properly grounded.
Damage caused by failure to follow these
instructions is not covered by the cooktop
warranty.
Tools Needed
aPencil
bSaber Saw
cPhillips Screwdriver
dFlat-Blade Screwdriver
ePliers
fTape Measure
gLevel
hDrill
iSafety Glasses
jGloves
Parts not Provided
aJunction Box
bWire Nuts
cStrain Relief (Conduit Connector)
en-us_main.book.book Page 9 Tuesday, October 17, 2023 1:22 PM
10 INSTALLATION
Unpacking the Cooktop
1 Unpack and visually inspect the cooktop for
any damage or missing components.
2 Be sure the bottle of cleaner and conditioner
packed in the literature bag is left where the
user can find it easily. It is important that the
ceramic-glass cooktop be pretreated before
use. See Care and Cleaning.
Model and Serial Number Location
The model and serial numbers are located on a
plate on the bottom of the cooktop. Please record
them in this guide; you will need them for
warranty registration.
Technical Specifications
Models LCE3010SBE
Description Radiant Cooktop
Electrical
Specifications
Connection
voltage 240/208 VAC 60 Hz., 32.1 A/27.9 A
Maximum
connected
power load
7700 W/5800 W
Cooktop Dimensions 30 27/32" (783 mm) (W) x 4" (101.6 mm) (H) x 21 15/32" (545 mm) (D)
Countertop Cutout Dimensions Standard Installation
29 3/8" (746 mm) (W) x 20 1/4" (515 mm) (D)
Cooking Zones
LCE3010SBE
Front Left 6 7/16" (163 mm) 1200 W
Front Right 9 15/16"/6" (253 mm/
152 mm) 3000 W/1400 W
Rear Left 8 3/4" (223 mm) 1900 W
Rear Right 6" (152 mm) 100 W (Warm)
Center 7 5/8" (193 mm) 1500 W
Models LCE3610SBE
Description Radiant Cooktop
Electrical
Specifications
Connection
voltage 240/208 VAC 60 Hz., 38.3 A/33.2 A
Maximum
connected
power load
9200 W/6900 W
Cooktop Dimensions 36 11/16" (932 mm) (W) x 4" (101.6 mm) (H) x 21 15/16" (557 mm) (D)
Countertop Cutout Dimensions Standard Installation
34 9/16" (878 mm) (W) x 20 3/8" (517 mm) (D)
en-us_main.book.book Page 10 Tuesday, October 17, 2023 1:22 PM
11INSTALLATION
ENGLISH
NOTE
The maximum power of each cooking zone depends on the size and material of the cookware used.
Cooking Zones
LCE3610SBE
Front Left 6 7/16" (163 mm) 1200 W
Front Right 9 15/16"/6" (253 mm/
152 mm) 3000 W/1400 W
Rear Left 8 3/4"/5" (223 mm/127
mm) 1900 W/950 W
Rear Right 6" (152 mm) 100 W (Warm)
Center
12 5/16"/9"/6" (313
mm/229 mm/152
mm)
3000 W/2200 W/1100
W
Models LCE3610SBE
en-us_main.book.book Page 11 Tuesday, October 17, 2023 1:22 PM
12 INSTALLATION
Preparing the Installation Location
Important Installation Information
All electric cooktops run off a single phase, three-wire or four-wire cable, 240/208 volt, 60 hertz, AC-only
electrical supply with ground.
Minimum distance between cooktop and overhead cabinetry is 30" (762 mm).
Make sure the cabinets and wall coverings around the cooktop can withstand the temperatures (up to 93
[200 ]) generated by the cooktop.
Dimensions and Clearances
aDo not obstruct these areas.
b4 X 8 (102 mm x 203 mm) opening to route armored cable if panel is present.
cApproximate location of junction box
-Dimension/Clearance LCE3010SBE LCE3610SBE
A Width of upper plate 30 27/32" (783 mm) 36 11/16" (932 mm)
B Depth of upper plate 21 15/32" (545 mm) 21 15/16" (557 mm)
C Height of cooktop base 3 3/4" (95 mm)
D Width of cooktop base 28 13/16" (732 mm) 33 27/32" (860 mm)
E Depth of cooktop base 19 5/8" (498 mm) 19 25/32" (502 mm)
F Width of cutout 29 3/8" (746 mm) 34 9/16" (878 mm)
G Depth of cutout 20 1/4" (515 mm) 20 3/8" (517 mm)
en-us_main.book.book Page 12 Tuesday, October 17, 2023 1:22 PM
13INSTALLATION
ENGLISH
All dimensions are stated in inches and millimeters (mm).
Allow 2" (50 mm) below the armored cable opening to clear the electric cable and allow space for
installation of the junction box on the wall at the back of the cooktop.
CAUTION
To eliminate the risk of burns or fire by reaching over heated surfaces, cabinet storage space located
above the cooktop should be avoided. If cabinet storage is provided, risk can be reduced by installing a
range hood that projects horizontally a minimum of 5" (127mm) beyond the face of the cabinets.
It is very important to keep 2 3/4" (70 mm) distance between the cooktop and an oven installed below it.
Installing the Cooktop
Electrical Connections
Important Safety Instructions
Be sure the cooktop is installed and grounded
properly by a qualified installer or service
technician.
This cooktop must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.
70, latest edition in the United States.
H Distance from side edge of cutout to side of counter 13/16" (20 mm)
I Distance from edge of cooktop to nearest
combustible wall (either side of unit)
23 3/4" (95 mm)
J Height below cutout
(Empty space is needed underneath the cooktop for
installation purposes.)
2 5 23/32" (145 mm)
K Distance from front of counter to front edge of cutout 2 1/2" (64 mm)
L Junction box (approximate location) 10" (254 mm)
M Junction box (approximate location) 12" (305 mm)
N Depth of overhead cabinets 1 13" (330 mm)
O Depth of bottom cabinets 24" (610mm)
P Clearance from top of cooking surface to bottom of
overhead cabinets
230" (762 mm)
Q Distance between rear edge of cutout and nearest
combustible surface.
236" (914 mm)
R Clearance from countertop to bottom of adjacent
cabinets
218" (457 mm)
-Dimension/Clearance LCE3010SBE LCE3610SBE
en-us_main.book.book Page 13 Tuesday, October 17, 2023 1:22 PM
14 INSTALLATION
WARNING
The electrical power to the cooktop must be shut
off while line connections are being made.
Failure to do so could result in serious injury or
death.
Providing the Electrical Connection
Install the junction box under the cabinet and
run 120/240 or 120/208 Volt, AC wire from the
main circuit panel.
NOTE
DO NOT connect the wire to the circuit panel at
this time.
Electrical Requirements
Observe all governing codes and local ordinances
1 A 3-wire or 4-wire single-phase 120/240 or
120/208 Volt, 60 Hz AC-only electrical supply is
required on a separate circuit fused on both
sides of the line (time-delay fuse or circuit
breaker is recommended). DO NOT fuse
neutral. The fuse size must not exceed the
circuit rating of the appliance specified on the
nameplate.
2 36" Radiant cooktop can consume up to 9200
W at 240 VAC. A 50 Amp circuit breaker with
#8 AWG must be used. 30" Radiant cooktop
can consume up to 7700 W at 240 VAC. A 40
Amp circuit breaker with #8 AWG must be
used.
WARNING
Do not use an extension cord with this
appliance. Doing so may result in a fire, electrical
shock, or other personal injury.
NOTE
Wire sizes and connections must conform to the
fuse size and rating of the appliance in
accordance with the National Electrical Code
ANSI/NFPA No. 70, latest edition, and local codes
and ordinances.
3 The appliance should be connected to the
fused disconnect (or circuit breaker) box
through flexible armored or nonmetallic
sheathed cable. The flexible armored cable
extending from this appliance should be
connected directly to the grounded junction
box. The junction box should be located as
shown in Dimensions and Clearances with
as much slack as possible remaining in the
cable between the box and the appliance, so it
can be moved if servicing is ever necessary.
4 A suitable strain relief must be provided to
attach the flexible armored cable to the
junction box.
Electrical Connection
Connect the flexible armored cable that extends
from the surface unit to the junction box using a
suitable strain relief at the point the armored cable
enters the junction box. Then make the electrical
connection as follows.
Electrical ground is required on this appliance.
This appliance is manufactured with a supply wire
and a frame-connected green or bare copper
grounding wire.
NOTE
TO ELECTRICIAN:
The armored cable leads supplied with the
appliance are UL-listed for connection to larger
gauge household wiring. The insulation of the
leads is rated at temperatures much higher than
the temperature rating of household wiring. The
current-carrying capacity of the conductor wire
is governed by the temperature rating of the
insulation around the wire, rather than the wire
gauge alone.
WARNING
DO NOT ground to a gas supply pipe. DO NOT
connect to electrical power supply until
appliance is permanently grounded. Connect the
ground wire before turning on the power.
This appliance is equipped with a copper
conductor flexible cable. If connection is made to
aluminum house wiring, use only special
connectors which are approved for joining
copper and aluminum wires in accordance with
the National Electrical Code and local codes and
ordinances. Improper connection of aluminum
house wiring to copper leads can result in a
short circuit or fire. Follow the connector
manufacturer’s recommended procedure
closely.
en-us_main.book.book Page 14 Tuesday, October 17, 2023 1:22 PM
15INSTALLATION
ENGLISH
Where Local Codes Permit Connecting
the Appliance-Grounding Conductor to
the Neutral (White) Wire
Observe all governing codes and local ordinances.
1 Disconnect the power supply.
2 At the circuit breaker box, fuse box or junction
box, connect appliance and power supply
cable wires as shown.
WARNING
You may not ground the cooktop through the
neutral (white) wire if cooktop is used in a new
branch circuit installation (1996 NEC), mobile
home, recreational vehicle, or where local codes
do not permit grounding to the neutral (white)
wire. When grounding to the neutral (white) wire
is prohibited, you must use a 4-wire power
supply cable. Failure to heed this warning may
result in electrocution or other serious personal
injury.
3-Wire Grounded Junction Box
aCable from Power Supply
bCable from Cooktop
cWhite Wire (Neutral)
dRed Wires
eGreen Wire (Ground)
fUL-listed Conduit Connector
gBlack Wires
hJunction Box
If Cooktop is Used in a New Branch
Circuit Installation (1996 NEC), Mobile
Home, Recreational Vehicle, or where
Local Codes Do Not Permit Grounding
to the Neutral (White) Wire
Observe all governing codes and local ordinances.
1 Disconnect the power supply.
2 At the circuit breaker box, fuse box or junction
box, connect appliance and power supply
cable wires as shown.
WARNING
If connecting to a 4-wire power supply cable
electrical system, the appliance frame connected
ground wire MUST NOT be connected to the
neutral wire of the 4-wire electrical system.
4-Wire Grounded Junction Box
aCable from Power Supply
bCable from Cooktop
cGround Wire
dRed Wires
eGreen Wire (Ground)
fUL-listed Conduit Connector
gBlack Wires
hJunction Box
iWhite Wire (No Connection)
en-us_main.book.book Page 15 Tuesday, October 17, 2023 1:22 PM
16 INSTALLATION
Installing the Cooktop Unit
1 Visually inspect the cooktop for damage.
Make sure all cooktop screws a are tight (see
below for locations).
2 Check and prepare the installation location.
•See Dimensions and Clearances.
3 Carefully lower the cooktop into the
countertop cutout, making sure not to trap
any wires.
NOTE
Do not use caulking compound. The cooktop
must be removable, should service be required.
4 Attach the retainer brackets a to the bottom
of the cooktop; then snug the bolts against
the bottom of the countertop as shown.
NOTE
The retainer brackets MUST be installed to meet
local codes or, in their absence, with the National
Electrical Code ANSI/NFPA No. 70, latest edition.
aCooktop
bCountertop
cBolt
dRetainer Brackets
eType A Screw
Alternative installation
LCE3010SBE
LCE3610SBE
aRetainer Brackets
bFront
cRear
en-us_main.book.book Page 16 Tuesday, October 17, 2023 1:22 PM
17INSTALLATION
ENGLISH
Final Check
Perform a final operational check of the cooktop,
making sure the cooktop powers on properly and
that each cooking zone operates correctly. Refer to
the Operating Instructions in this guide for details.
en-us_main.book.book Page 17 Tuesday, October 17, 2023 1:22 PM
18 OPERATION
OPERATION
Cookware
Selecting Cookware
Pots and Pans
The better the pot, the better the cooking results.
You can recognize good pots and pans by their
bases. The base should be as thick and flat as
possible.
Pots with aluminum or copper bases can cause
metallic discoloring on the ceramic glass surface
which is very difficult or impossible to remove.
Be very careful when using cast iron pots or pots
with damaged bases which are rough and or
have burrs on them. Scratches can occur if they
are slid across the surface.
When cold, pot bases are normally bowed
slightly inwards (concave). They should never be
bowed outwards (convex).
When using specialty cookware such as pressure
cookers, simmering pans, or woks, follow the
manufacturer’s instructions and do not use a
very thin pan.
Use Flat-Bottomed Cookware
Cookware must fully contact the surface of the
cooking element. Use flat-bottomed pans sized to
fit the cooking element and amount of food being
prepared. Check for flatness by rotating a ruler
across the bottom of the cookware.
Avoiding Scratches
Use heavier gauge stainless steel cookware on
your ceramic cooktop surface. This will help reduce
the possibility of developing scratches on the
ceramic surface.
Low-quality cookware can scratch the cooktop
surface.
Cookware should always be lifted over the ceramic
cooktop surface to prevent scratching. Over time,
sliding ANY type of cookware over the ceramic
cooktop may alter the overall appearance of the
cooktop. Eventually, the buildup of scratches can
make cleaning the surface difficult and degrade
the overall appearance of the cooktop.
Scratches can also result from grains of sand (for
example, after washing vegetables) which are
dragged with the pot across the cooking surface.
Using Cookware
Always follow the recommendations for proper
cookware type and size. In addition:
Do not use dirty pans with grease buildup.
Always use pans that are easy to clean after
cooking, and make sure that the bottoms of the
pans are clean and dry.
When cooking with large amounts of liquid, use
large pots so that nothing can boil over.
Do not let pans boil dry. This may cause
permanent damage in the form of breakage,
fusion, or marring that can affect the ceramic
cooktop. (This type of damage is not covered by
your warranty.)
Match the pan size and element to the amount
of food being prepared.
Tips for Saving Energy
Always position pots and pans before you switch
on the element.
Dirty elements and cookware use more
electricity.
Whenever possible, always have the lid firmly
placed on the pots and pans so that they are
completely covered.
Switch off the elements before the end of the
cooking time to use the residual heat for
keeping food warm or for melting.
en-us_main.book.book Page 18 Tuesday, October 17, 2023 1:22 PM
19OPERATION
ENGLISH
The base of the pot should be the same size as
the element.
Using a pressure cooker shortens cooking times
by up to 50%.
en-us_main.book.book Page 19 Tuesday, October 17, 2023 1:22 PM
20 OPERATION
Control Panel
Control Panel Features
Locations of Surface Elements and Controls
The surface burner elements are positioned in the same locations on the cooktop and the control panel for
ease of use.
Before Using the Cooktop
Before using the cooktop for the first time, clean it
thoroughly with the included cleaner or ceramic
cooktop cleaner according to the Care and
Cleaning instructions in this guide. This will help
protect the ceramic surface and make future
cleanup easier.
LCE3010SBE LCE3610SBE
LCE3010SBE LCE3610SBE
aWARM: Lowers the selected active element to the lowest setting.
bHot surface indicator: The indicator light below HOT will illuminate when the cooking area is hot.
It will remain on, even after the control is turned off, until the area has cooled.
cCHILD LOCK: Press and hold for 3 seconds to activate and deactivate the Child Lock function.
dWARM: Indicates that a surface burner has been set to Warm.
eSingle element, left front element
fPOWER ON/OFF: Press POWER ON/OFF to turn the entire cooktop ON and OFF. When it is ON,
the cooktop is in standby mode until an element is activated. Set the power level for an element
by selecting a number from 1 to 9 in the element power settings.
gDual element, right front element
hDual element indicator
iWarming zone
jSingle element, center rear element Triple element, center rear element
kSingle element, left rear element Dual element, left rear element
l- Triple element indicator
en-us_main.book.book Page 20 Tuesday, October 17, 2023 1:22 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108

LG LCE3610SBE Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues