Falcon W202333 Manuel utilisateur

User manual

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S

Ł

U G I

N Á V O D K O B S L U Z E

Falcon

Instrukcje dla wyspecjalizowanego

Alle rechten, inclusief vertaling, voorbehouden.

Alle Rechte, auch an der Übersetzung, vorbehalten.

traducción.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Všechna práva vyhrazena, včetně překladu.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: A, 2022-11

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : A, 2022-11

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: A, 2022-11

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: A, 2022-11

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: A, 2022-11

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: A, 2022-11

PL

sprzedawcy

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: A, 2022-11

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: A, 2022-11

Basic UDI: 5415174FalconDQ

Multi version: A, 2022-11

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Falcon

2022-11

Contents

1

EN

NL

Contents

Contents ..................................................................................................................... 1

Preface........................................................................................................................ 2

1 Your product .................................................................................................. 3

2 Before use ..................................................................................................... 4

2.1 Intended use ................................................................................................. 4

2.2 General safety instructions ............................................................................ 4

3 Using the patient hoist ................................................................................. 5

3.1 Operating the lift ............................................................................................ 5

3.2 Slings ............................................................................................................ 7

3.3 Battery and charging ..................................................................................... 9

3.4 Emergency .................................................................................................. 10

4 Installation and adjustment........................................................................ 11

4.1 Delivery ....................................................................................................... 11

4.2 Assembly or dismantling ............................................................................. 11

5 Maintenance ................................................................................................ 13

5.1 Time of maintenance ................................................................................... 13

5.2 Shipping and storage .................................................................................. 14

5.3 Cleaning ...................................................................................................... 14

5.4 Disinfection ................................................................................................. 14

5.5 Inspection .................................................................................................... 15

5.6 Expected lifespan ........................................................................................ 15

5.7 Reuse .......................................................................................................... 15

5.8 End of use ................................................................................................... 15

6 Troubleshooting .......................................................................................... 16

7 Technical specifications ............................................................................. 17

Falcon

2022-11

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren patient hoist!

This product is made by qualified and committed personnel. It is designed and produced

according to high quality standards, guarded by Vermeiren.

Thank you for your trust in the products of Vermeiren. To support you on the use of this patient

hoist and its operating options, this manual is offered. Please read it carefully; it will help you to

get familiar with the operation, capabilities and limitations of your product.

If you still have questions after reading this manual, do not hesitate to contact your specialist

dealer. He/she will be glad to help you.

Important note

To ensure your safety and to prolong the lifetime of your product, please take good care of it and

have it checked and serviced on a regular basis.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without any obligation to adapt or replace similar products

previously delivered.

Pictures of the product are used to clarify the instructions in this manual. Details of the depicted

product may deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of the

information in this manual. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

This user manual

For user and specialist dealer

Service manual

For specialist dealer

EC declaration of conformity

Falcon

2022-11

Your product

3

EN

NL

1 Your product

1. Cantilever arm

2. Spreader bar

3. Motor

4. Chassis

5. Roller

6. Control box

7. Handle for pushing

8. Manual operation

9. Emergency stop

10. Pole

11. Chassis expansion pedal

12. Caster with brake

1

2

9

10

8

7

4

6

5

11

3

12

Falcon

2022-11

Before use

4

EN

NL

2 Before use

2.1 Intended use

In this paragraph a brief description of the intended use of your patient hoist is given. Additionally,

relevant warnings are added to the instructions in the other paragraphs. In this way we would like

to make you aware of the possible misuse that may appear.

• Indications and contraindications: This patient hoist is meant to be operated by an attendant to

transfer sitting patients between e.g. wheelchairs, nursing beds and bathrooms. The patient

hoist is designed and produced to be a transport/transfer aid for elderly persons or persons

who suffer from paralysis, limb loss or defects, stiff or damaged joints, cardiovascular problems,

cachexia, … .

• This patient hoist is suitable for indoor use.

• This patient hoist is designed and produced solely to transport/transfer one (1) person with a

maximum weight according to the specifications in §7. It is not designed for transportation of

goods or objects, nor for any use other than previously described.

• Only use accessories and spare parts approved by Vermeiren.

• Please read all technical details and limits of your patient hoist in chapter 7.

• The warranty on this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 General safety instructions

Risk of injuries and/or damage

Please read and follow the instructions in this manual. Otherwise you may get injured or your

patient hoist may get damaged.

Keep the following general warnings in mind during use:

• The patient hoist must only be operated by qualified staff who have been instructed or trained

in its specific application.

• Do not exceed the maximum load for the patient hoist. This will shut down the control box.

• In case of different user weights for patient hoist and slings, always observe the lowest user

weight.

• An attendant needs to be present during the lifting operation.

• Be aware that some parts of the patient hoist may get very hot or cold due to ambient

temperature, solar radiation or heating devices. Be careful when touching.

• The patient hoist has been tested for electromagnetic compatibility and complies with the

standard. Nevertheless, sources of electromagnetic fields may influence the performance of

the patient hoist, such as the fields of mobile phones, power generators or high-power energy

sources. On the other hand, the electronics of the patient hoist can affect other electronic

appliances too.

• Only use the patient hoist on flat surfaces where all castors touch the ground and where there

is sufficient contact to operate the patient hoist safely. Do not take obstacles with the patient

hoist while transferring a patient.

• Do not use the patient hoist in wet or humid environments.

• Alterations or substitutions should not be made to the patient hoist securement points or to

structural and frame parts or components without consulting the manufacturer.

• Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or

other moving parts during use.

• Be careful with sources of ignition such as lit cigarettes as they may set the sling alight.

In case a serious incident has occurred involving your product, notify Vermeiren or your specialist

dealer as well as the competent authority in your country.

CAUTION

Falcon

2022-11

Using the patient hoist

5

EN

NL

3 Using the patient hoist

3.1 Operating the lift

Risk of injuries and/or damage

• When using the lift, make sure that there is sufficient room around and above it, as the

adjustment movements could otherwise lead to damage or injury.

• Always be aware of the lifting arm to avoid injury.

• Only slings that have been designed and approved for the patients must be used (see usage

instructions for the various slings). Use of any other slings is at your own risk.

• Only use the handles to push/pull the patient hoist, no other components.

Please observe the technical information according to which the patient hoists may be operated.

The patient hoist must only be operated by authorised staff who have been trained in its use and

operation.

3.1.1 Altering the chassis width

To get the lift around a wheelchair or other seating

furniture, or to increase the stability of the lift in the

standing position, the separation of the chassis legs

can be increased.

Stand behind the assembled lift and take hold of the

handles for pushing the patient hoist (on the left and

right, next to the control box). Press the lever at the

bottom of the chassis (left or right) down with your foot,

and the separation of the legs of the chassis can be

increased or decreased.

3.1.2 Parking brakes

Secure the two casters at the back of the chassis by

pressing the caster brake plates down gently to their end

stops with the tip of your foot. To release the brake, push

the brake plate gently back up again with the front of

your foot until the casters are free.

3.1.3 Raising and lowering the cantilever arm

The manual control allows the cantilever arm to be adjusted smoothly to any

point.

= Raise the cantilever arm

= Lower the cantilever arm

When using the lift function until the end of the hoist motor, the limit switch is

activated by electronics (security function). Use the lifting function only in the

middle of the adjustment range.

CAUTION

1

2

1

2

Falcon

2022-11

Using the patient hoist

6

EN

NL

3.1.4 Lowering button

If the manual operation mechanism should be damaged, it is possible

to lower the cantilever arm from the control box.

The arm moves down for as long as the button (3) on the control box

panel is pressed.

3.1.5 Moving the patient hoist

Risk of injuries

• Be careful passing through restricted passages (e.g.

doors).

1. Stand behind the patient hoist and grasp the

handles (left and right, next to the control box) with

both hands.

2. Make sure that both back caster brakes have been

released.

3. Push the patient hoist slowly into the desired

position.

When it is not loaded, we advise you to pull the patient

hoist backwards, which makes it easier to get round any

obstacles (door frames, corners of rooms or furniture).

3.1.6 Turn the patient hoist around his axle

Risk of injuries

• Be careful there are no people or objects in the

swing range of the patient hoist.

• Turn the patient hoist carefully and slowly around

his axle, so that the patient cannot swing out.

1. Open the legs of the patient hoist to give more

stability.

2. Activate the brakes.

3. Place the patient in the patient hoist with the

appropriate sling. (refer to sling manual for

instructions of placing the patient in the hoist).

4. Lift the patient from the ground, chair, bed, ... .

5. Loosen both brakes of the rear wheels.

6. Stand behind the patient hoist and grasp the

handgrips (left and right next to the control box)

with both hands.

7. Now turn the patient hoist carefully, slowly around

on the same place. Be careful you do not touch any objects with the legs of the patient hoist.

8. When you are turned in the good position, you can lift the patient down.

CAUTION

3

Falcon

2022-11

Using the patient hoist

7

EN

NL

3.2 Slings

Risk of injuries

• Only use appropriate slings for the patients.

• Do not use damaged slings.

• Read the full slings manual first.

• Only use compatible slings approved by Vermeiren.

The patient hoist must only be used with slings designed for the Vermeiren Falcon patient hoists

(for 4-point speader bar).

The applicability and instructions for use for the specific slings should be followed, see the

separate manual.

3.2.1 Attaching to the spreader bar of the patient hoists

The slings shall be attached by the mounting straps. These mounting straps shall be suspended

on the spreader bar of the patient hoist.

The mounting straps of the slings have 4 loops in different colors.

Mounting strap sling

Spreader bar of the patient hoists

With these loops it is possible to lift the patient in different positions. These positions depends

on the length and weight of the person.

CAUTION

Hooks for

mounting strap

Black

Yellow

Red

Green

Falcon

2022-11

Using the patient hoist

8

EN

NL

Shoulders

Legs

Head

(only by comfort

sling)

Green

Red

Yellow

Black

The legrests can be attached on the patient hoist according different methods.

• Crossed legrests

This is the most used method to attach the sling. The attachment of the sling with crossed

legrests shall be according to the instructions below:

1. Put the mounting strap of the legrest through the loop of the other legrest.

2. Attach the mounting straps of the legrests on the spreader bar of the patient hoist.

• Crossed under both thighs

L CAUTION: Risk of falling - By a patient with amputated legs increases the

risk of falling because the patient loose easy his balance.

This method can be used for lifting a patient with amputated legs. The attachment of the

sling crossed under both thighs shall be according to the instructions below:

1. Cross the mounting strap of the legrest under the thighs.

2. Attach the mounting straps of the legrests on the spreader bar of the patient hoist.

Falcon

2022-11

Using the patient hoist

9

EN

NL

• Each legrest separately on the spreader bar

L CAUTION: Risk of falling- This method increases the chance of sliding out the

sling.

Attaching each legrest separately on the spreader bar can be used for patient with sensitive

genitals. The attachment of the sling with this method shall be according instructions below:

1. Put the legrest around each leg separately, but not crossed.

2. Attach the mounting straps of the legrests on the spreader bar of the patient hoist.

3.2.2 Position of spreader bar

The spreader bar must always be perpendicular to the body of the patient. The left figure is the

good method. The right figure is the wrong way.

3.3 Battery and charging

3.3.1 Battery charger

Primary voltage

100 - 240VAC / 50/60 Hz

Safeguards

Protected against reverse polarisation, electrical surges

and extreme temperature

Ambient temperature

0 to +40°C

Length of mains lead

2.0 m

Ambient storage temperature

-15° to +50°C

Relative storage humidity

max. 95% (non-condensing)

Conformity

tested in accordance with IEC 60601-1

3.3.2 Charging the batteries

Use only the control box with included battery charger.

We recommend that you should regularly recharge the batteries in order to ensure that the hoist

remains usable and to extend the lifespan of the batteries. The control box will give a warning

sound to tell you when the battery charge is low.

First use

First, insert the supply cable with the connector side into the appropriate connector on the control

box. The plug side of the supply cable must be insert in the socket outlet. The loading time is

about 24 hours.

Recharging

L WARNING: Risk of injury – Do not use the lift when the supply cable is connected in

the socket outlet.

When the battery is running low, only the left LED will light green. Once the battery level gets

very low, the LED will light red and a beeping sound can be heard every 2 seconds.

Falcon

2022-11

Using the patient hoist

10

EN

NL

The battery is fully charged once all LEDs are fully green.

After the recharging process is completed, you should always remove the mains plug from the

socket first and then remove the connector plug from the control box.

Do not use the lift while it is being recharged!

If the batteries are not used for a significant period, they discharge slowly by themselves (deep

discharge). It then becomes impossible to recharge them. You should therefore recharge the

batteries at least once a month even if they are not being used.

3.4 Emergency

In cases for emergency the emergency stop and the function for lowering in an emergency must

be used.

3.4.1 Emergency stop

In emergencies, and during assembly and disassembly, the

emergency stop is activated by pressing the red button on the

control box.

Push the button and turn in the direction of the arrows. If the

button is fully pressed to the back turn back in the opposite

direction of the arrows.

The emergency stop is deactivated by turning the red button in

the direction of the arrows.

3.4.2 Emergency lowering

L WARNING: Risk of injury – Adjust the manual emergency

lowering for the weight of the patient.

Emergency lowering if the power fails or the batteries are empty can be

done by turning the red button at the upper end of the motor.

Please note that the manual emergency lowering is only possible when the

patient is sitting in the patient hoist.

Falcon

2022-11

Installation and adjustment

11

EN

NL

4 Installation and adjustment

The patient hoist is delivered fully assembled by your specialist dealer.

The instructions in this chapter are for the specialist dealer.

To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.

L WARNING: Risk of unsafe limitations - Use only the limitations described in this

manual.

4.1 Delivery

The Vermeiren Falcon patient hoist shall be delivered with:

• chassis including 4 casters (2 with brakes)

• pole, including handles for pushing

• cantilever arm and spreader bar

• control box (incl. 2 accumulator batteries and manual operation)

• battery charger

• motor

• instruction manual

Before use check if everything is included and that no products are damaged (example by

transport, ...).

Please note that the basic configuration may vary from one European country to another. Please

contact the specialist dealer in your country for more information.

4.2 Assembly or dismantling

4.2.1 Unpacking

L WARNING: Risk of injury - After unpacking and before further assembly, always first

confirm that the emergency stop (the red pushbutton on the control box) is pressed in.

The patient hoist packaging has been selected to provide the best possible protection during

transport.

1. Take all parts of the patient hoist out of the box and check

that all the items have been delivered and that the individual

parts do not have any visible defects. If there is any damage,

please contact your sales office.

2. Before assembly, put on the caster brakes to make sure that

the lift cannot be moved unintentionally. Push the caster

brake plate down gently to its end stop with the front of your

foot. To release the brake, push the brake plate gently back

up again with the front of your foot until the caster is free.

Falcon

2022-11

Installation and adjustment

12

EN

NL

4.2.2 Assembly

L WARNING: Risk of clamping - Take care that no body parts and wires

get trapped, crushed or cut during assembly.

1. Insert the vertical pole into the lower frame and tighten the lever securely.

2. Place the motor in its attachments on the vertical pole and the hoist arm

(4) and secure into place with the pins.

3. For first use: Mount the control box to the vertical pole by tightening the

two bolts.

4.2.3 Dismantling

L WARNING: Risk of clamping - Take care that no body parts and wires

get trapped, crushed or cut during dismantling.

L WARNING: Risk of injury - Check the emergency stop (red

pushbutton on the control box) is activated, to avoid unintentional

adjustment movements.

1. Secure the two casters at the back of the chassis by pressing the caster

brake plates down gently to their end stops with the tip of your foot. To

release the brake, push the brake plate gently back up again with the

front of your foot until the casters are free.

2. Release the motor from the hoist arm and vertical pole by removing the

pins (4).

3. Remove the lever and take the vertical pole out of the lower frame.

4

3

4

3

Falcon

2022-11

Maintenance

13

EN

NL

5 Maintenance

5.1 Time of maintenance

Risk of injuries and damage

Repairs and replacements may only be undertaken by trained persons and only genuine

replacement parts of Vermeiren should be used (see the maintenance manual).

The last page of this manual contains a registration form for the specialist dealer to record

each service.

The service frequency depends on the frequency and intensity of use. Contact your dealer to

agree to a common timetable for inspection/maintenance/repair.

For the maintenance manual, refer to the Vermeiren website: www.vermeiren.com.

Before each use

Inspect the following points:

• All parts: present and undamaged or unworn.

• All parts: clean, see §5.3.

• Condition of frame parts: no deformation, instability, weakness or loose connections.

• Brakes: no visible damage and/or dirt.

• Control box, manual control, battery charger, relevant cables: no damage such as wires that

have become frayed, broken or exposed. Check that the electrical adjustment of the

cantilever arm is working properly, using the manual control.

• Battery status: charge the battery when necessary, see §3.3.

Approx. every 8 weeks

Depending on the frequency of use, check the following:

• Lubrication of the joints of the cantilever arm

• Condition of the casters

• Whether there is any visible damage to the casing of the control box, battery, battery

charger and the manual controls

• Whether the cables are fit for use

• Recharge the battery

Approx. every 6 months or for every new user

Depending on the frequency of use check the following:

• Cleanliness

• General condition

• That the battery charger is working

• Casters are working

If the resistance to rotation is too great, clean the casters. If this is insufficient, please consult

your dealer.

Yearly or more often

Have the patient hoist inspected and serviced by your specialist dealer, at least once a year, or

more often. The minimum maintenance frequency depends on use and should therefore be

commonly agreed upon with your specialist dealer.

CAUTION

Falcon

2022-11

Maintenance

14

EN

NL

5.2 Shipping and storage

• Shipping and storage should happen according to the technical specifications in §7. Make

sure that the patient hoist is stored dry.

• Prevent cables from being crushed or bent with kinks.

• Disconnect the patient hoist from the socket.

• Provide sufficient covering or packaging to protect the patient hoist against rust and foreign

bodies. (e.g. salt water, sea air, sand, dust).

• Store all removed parts together in one place (or mark them if necessary) to avoid mixing up

with other products when re-assembling (e.g. the charger).

• Make sure no objects are stored on or against the patient hoist and its components to prevent

damage.

5.3 Cleaning

Risk of damage by moisture

• Never use a hose or high-pressure cleaner.

• Use a mild commercial detergent to remove stubborn dirt.

• Stains can be removed by using a sponge or a soft brush.

• Do not use strong cleaning liquids like solvents, nor use hard brushes.

5.3.1 Plastic parts

Clean plastic parts of your patient hoist with commercial plastic cleaners. Read the specific

product information and only use a soft brush or soft sponge.

5.3.2 Coating

The high quality of the surface layer guarantees optimal protection against corrosion. If the outer

coat is damaged by scratching or in some other way, get your specialist dealer to repair the

affected surface.

When cleaning, only use warm water and normal household detergents and soft brushes and

cloths. Ensure that no wetness gets into the tubes.

5.3.3 Electronics casing

L WARNING: Risk of injury - The emergency stop must be activated before maintenance

work, so that no unintentional adjustment movements can be made.

Wipe the control box, motor casing and manual controls down with a cloth moistened by a few

drops of a commercial domestic cleaner. Do not use abrasives or sharp-edged polishing

equipment like a metal scrubber or brush, as these can scratch the surface of the manual control

and destroy its water repelling property.

Regularly check the plug connectors for corrosion or damage, as these could affect the functional

integrity of the electronics.

The manufacturer will not accept liability for damages caused by insufficient maintenance.

5.4 Disinfection

L WARNING: Dangerous Products - The use of disinfectants is restricted to authorized

personnel.

All parts of the patient hoist can be treated by scrubbing with a commercial disinfectant. Follow

the instructions on the disinfectant.

Washing instructions for slings can be found in the slings manual and on the label of each sling.

CAUTION

Falcon

2022-11

Maintenance

15

EN

NL

5.5 Inspection

In principle we recommend one inspection every year, and a minimum of one before usage is

resumed. All of the following checks must be performed and documented by authorized

persons:

• Check the cabling (in particular for crushing, wear, cuts, visible parts of the insulation of

the inner wires, visible metal wire cores, kinks, bulges, colour changes of the outer sleeve,

brittle spots, and safe positioning so that mechanical effects such as being cut or crushed

are not probable).

• Visual inspection of the frame parts to check for plastic deformation and/or wear and tear

(frame, motor suspension, cantilever arm, spreader bar).

• Visually check for damage to the paintwork (danger of corrosion).

• Visual inspection of all casings for damage; screws must be tight.

• Verify the amount of grease on the metal joints of movable parts

• Visually check all plastic parts for cracks and brittle spots

• Review the control box + included charger residual discharge current (A) based on

VDE 0702

• Review the control box + included charger insulation resistance (MO) based on VDE 0702

• Functional test of the cantilever arm (lubrication of the joint parts, range of adjustability,

deformation, wear and tear)

• Check the functioning of the hoist drives (during a test drive → noises, speed, free running,

etc.), if necessary: Measure the performance, first with no load and then with the nominal

load ("SWL"), to investigate the wear and tear of the motors by comparing the values for

the electric current against the values when it was delivered.

• Functional test of the emergency stop

• Functional test of the emergency lowering

• Completeness of the delivery condition, instruction manual available?

Checking measurements may only be carried out by skilled persons trained on the patient hoist

at least and at least under the supervision of an electrician who knows the checking instruments

and processes. Only an electrician can release the patient hoist for use after making the

measurements and carrying out the servicing.

The service must only be signed off in the maintenance plan if a minimum of all the above-

mentioned aspects have been checked.

5.6 Expected lifespan

The average lifespan of the patient hoist is 8 years. Depending on the frequency of use, storage,

maintenance, servicing and cleaning, the lifespan of the patient hoist will increase or decrease.

5.7 Reuse

Before each reuse, have the patient hoist disinfected, inspected and serviced according to the

instructions in this chapter.

5.8 End of use

At end of life, you need to dispose of the patient hoist according to the local environmental

legislation. The best way to do so, is to disassemble the patient hoist to facilitate the transport of

recyclable parts.

Falcon

2022-11

Troubleshooting

16

EN

NL

6 Troubleshooting

Table 1: Troubleshooting

Problem

Cause of problem

Problem solving

Noisy sound of the moving

parts (example: cantilever

arm).

Lubrication is necessary.

Lubricate the moving parts.

(Do not lubricate the actuator!)

Actuator makes an unusual

sound.

The actuator is damaged.

Replace the actuator or contact

your specialist dealer.

Patient hoist does not lift

anymore.

1. Electric actuator is damaged.

2. The user weight is too high

(overload LED on manual

control lights up).

3. Manual control or actuator are

not connected.

4. Battery not connected or not

connected properly to control

box.

5. Battery too low.

6. Emergency stop is activated.

1. Replace the actuator.

2. Use a patient hoist with higher

maximum user weight.

3. Check connections. If

necessary connect manual

control or actuator.

4. Check battery is installed or

the connection of the battery.

5. Charge the batteries or

replace.

6. Deactivate the emergency

stop.

Lowering the patient in case

of emergency does not

work.

There is required a minimum

weight load to lower the patient.

If the patient weight is too low pull

down slightly on the cantilever

arms or adjust the lowering speed.

Battery cannot be charged

1. Batteries not fitted correctly to

control box.

2. Mains cable defect.

3. Batteries are defected.

4. Control box with included

charger is defected

5. Battery charger is defected

1. Check batteries are connected

to the control box.

2. Change mains cable.

3. Replace battery.

4. Replace control box with

included charger.

5. Replace new battery charger.

La page charge ...

Falcon W202333 Manuel utilisateur

Falcon W202333 Manuel utilisateur

dans d''autres langues

Autres documents