Posiflex XT-7315/7515 Manuel utilisateur

1

Package Contents

 15” P-CAP touch terminal with Gen 7E or

Gen 8E base…………………………..(x1)

 Power adapter………………………...(x1)

 Power cord……………………………(x1)

 User manual…………………………..(x1)

Product Features

 Fanless Design

 Intel Coffeelake-S platform

 New Gen 7E foldable base that allows JIVA XT Series to be configured

into different configurations

 New Gen 8E foldable base that integrates internal power adaptor and

Powered USB port into the base

 M.2 expansion slots for SSD storage and Wi-Fi / Bluetooth

communication module

16800902020 Ver. B0

http://www.posiflex.com

XT-7315/7515

Fanless POS Terminal

User Manual

2

SOME IMPORTANT NOTES

FCC NOTES

This system meets industry & government requirements and applicable

standards. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions

manual, may cause interference to radio communications. It has been tested

and found to comply with limits for a Class A digital device pursuant to

subpart B of Part 15 of FCC Rules, which are designed to provide reasonable

protection against interference when operated in a commercial environment.

Operation of this equipment in a residential area is likely to cause interference

in which case the user at his own expense will be required to take whatever

measures to correct the interference.

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential

environment this equipment may cause radio interference.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any

person other than the authorized technicians. The user should consult his/her

dealer for the problem happening. Warranty voids if the user does not follow

the instructions in application of this merchandise. The manufacturer is by no

means responsible for any damage or hazard caused by improper application.

警告使用者

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，

在這種情況下，使用者會被要求採取某些適當的對策。

SAFETY INSTRUCTIONS

This equipment is not suitable for use in locations where children are likely to

be present.

3

CONSIGNES DE SÉCURITÉ

Cet équipement ne convient pas à une utilisation dans des lieux pouvant

accueillir des enfants.

BATTERY CAUTION NOTES

 Dispose of used batteries according to the instructions.

 Replacement of a battery with an incorrect type that can defeat a

safeguard (for example, in the case of some lithium battery types)

 Disposal of a battery into fire or a hot oven, or mechanically crushing

or cutting of a battery that can result in an explosion.

 Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or the leakage of flammable

liquid or gas.

 A battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas.

BATTERIE ATTENTION NOTES

 Jetez les piles usagées conformément aux instructions.

 Remplacement d'une batterie avec un type incorrect qui peut annuler

une sauvegarde (par exemple, dans le cas de certains types de batterie

au lithium)

 Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou

écrasement ou coupure mécanique d'une batterie pouvant entraîner une

explosion.

 Laisser une batterie dans un environnement environnant à des

températures extrêmement élevées pouvant entraîner une explosion ou

la fuite de liquide ou de gaz inflammable.

 Une batterie soumise à une pression atmosphérique extrêmement basse

pouvant provoquer une explosion ou une fuite de liquide ou de gaz

inflammable.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之

電池。

4

Views of XT-7315/7515 with Gen 7E Base

Front View

Rear View

Side View

Cable Cover

Neck Cover

Cable Exit

Power Button

Brightness Adjustment Button ＋

Brightness Adjustment Button －

HDD/SSD Cover

LED indicator

Gen 7E Base

P-CAP Touch Panel

5

Bottom View

Views of XT-7315/7515 with Gen 8E Base

Front View

Rear View

Cable Holder

Cable Exit

Cable Cover

Neck Cover

Cable Exit

LED indicator

Rubber Feet with Fixing Screw

Gen 8E Base

HDD/SSD Cover

P-CAP Touch Panel

6

Side View

Bottom View

View of I/O Interface of XT-7315/7515

Power Button

Brightness Adjustment Button ＋

Brightness Adjustment Button －

Rubber Feet with Fixing Screw

UPS Battery

Compartment

Power Adapter

Compartment

PoweredUSB

Compartment

HD Compartment

DC IN

Power

Connector

USB 2.0 Ports

USB 3.0 Ports

VGA Port

LAN Ports

Line Out

DB9 COM Ports

RJ-50 COM Ports

CR Port

12V BAT Port

(UPS Port)

Mini-HDMI Port

7

Positioning your POS for a Perfect Viewing Angle

The adjustable bases designed for XT-7315/7515 come in two models, Gen

7E/8E, and allow you to determine an ideal position for your terminal by using

its unique tilt adjustment mechanism. As the below figures suggest, both bases

provide three standard positioning solutions for your terminal: Flat Folded

mode, Low Profile mode, and Full Extended mode.

XT-7315/7515 with Gen 7E Base

Flat Folded mode

Low Profile mode

Full Extended mode

XT-7315/7515 with Gen 8E Base

Flat Folded mode

Low Profile mode

Full Extended mode

In general, XT-7315/7515 will be set up beforehand in Flat Folded mode and

then packaged into the box for shipping. After it is unpacked, you may re-

adjust the terminal in either Low Profile mode or Full Extended mode

according to your situation. Below will provide instructions on how to adjust

the specific base connected to the POS system. As a reminder, please be

careful not to touch the LCD panel while setting up the tilt angle.

XT-7315/7515 with Gen 7E Base

Please refer to the following instructions on how to switch among different

positioning modes to find an ideal viewing angle for XT-7315/7515 with Gen

7E base.

8

1. Unpack XT-7315/7515, which is supposed to

be set in flat folded mode, out of the package

box and then lay your POS system on a flat

surface.

2. Steady the base with one hand, and then tilt

the screen downwards.

3. Position your terminal in Full Extended mode

3.1 After grabbing the bottom edge of the screen with your hand, gently

move the screen upward until the screen is locked into place with a

click sound.

3.2 Support the screen with one hand holding onto its bottom edge.

Then, while pulling the lever backwards, move the display upwards

until the lever is snapped into the lower hook to raise the screen as

shown in the below figure.

Lever

Lower

hook

9

3.3 With the screen facing toward you, tilt the

screen up or down to your desired angle.

Please do not press on the LCD panel while

setting up the tilt angle.

3.4 Remove the cable cover from the base.

3.5 Fix the base with two #/6/32-14L screws.

4. Return your terminal back to Flat Folded mode from Full Extended

mode.

4.1 Remove the cable cover from the base.

10

4.2 Remove the two screws from the base.

4.3 Tilt your screen in a horizontal position.

4.4 Support the screen with one hand holding onto its bottom edge.

While pulling the lever backwards, move the display downwards

until the lever is lifted off the hook as shown in the figure.

Remove the two screws.

Hook

Lever

11

4.5 Push the cable cover back.

4.6 Tilt the screen again to the horizontal

position.

5. Position the terminal in Low Profile mode.

5.1 Follow Step 4 to set up the termimal in Flat

Folded mode.

5.2 Tilt the screen all the way down

5.3 To tilt screen up or down to your desired

angle, please be advised to keep the base

steady with one hand to do so. Do NOT

press on the LCD panel while setting up the

tilt angle.

XT-7315/7515 with Gen 8E Base

Please refer to the following instructions on how to switch among different

positioning modes to find an ideal viewing angle for XT-7315/7515 with Gen

8E base.

12

1. Unpack XT-7315/7515, which is

supposed to be set in flat folded mode, out

of the package box and then lay your POS

system on a flat surface.

2. While steadying the terminal with your

hand holding onto the base, tilt the screen

down.

3. Push the cable cover outwards to remove

it from the base.

4. Position your terminal in Full Extended mode.

4.1 Support the screen with one hand holding onto its bottom edge.

Then, while pulling the lever backwards, move the display upwards

until the lever is snapped into the lower hook to raise the screen as

shown in the below figure.

4.2 Tilt the screen up or down to your

desired angle. Please do not press on

the LCD panel while setting up the tilt

angle.

Lower

hook

Lever

13

4.3 Fix the base with two #/6/32-14L screws.

4.4 Push the cable cover back.

5. Position the terminal in Low Profile mode.

5.1 While keeping your terminal steady with your hand holding on to

the base, tilt your terminal down. Then, remove the cable cover

from the base.

14

5.2 Remove the two screws from the base.

5.3 Support the screen with one hand holding onto its bottom edge.

Then, while pulling the lever backwards, move the display

upwards or downwards until the lever is snapped into the upper

hook to lower the screen as shown in the below figure.

5.4 Push the cable cover back.

5.5 Tilt the screen up or down to your

desired angle. Please do not press on

the LCD panel while setting up the

tilt angle.

Lever

Upper

hook

Remove the two screws.

15

6. Return the terminal back to Flat Folded mode.

6.1 While steadying your terminal with your hand holding onto the

base, tilt your screen up.

6.2 Support the screen with one hand holding onto its bottom edge.

While pulling the lever backwards, release the lever back to the

point above the upper hook as shown in the figure.

6.3 Push the cable cover back.

6.4 Tilt the screen to the horizontal position.

Lever

Upper

hook

16

Connecting Power Adapter and I/O Cables

To have the terminal ready for operation, please connect the connector of

power adapter and all of the connectors of required I/O cables respectively to

the 12VDC-IN power jack and appropriate I/O ports. Please make sure that

each of the cables is fully connected to each of the correct ports. Damages due

to incorrect connection or orientation are not covered by product warranty!

Some cable connectors like the connectors of the COM or LAN cables have to

be gently inserted until a click is heard. It is recommended that the I/O ports,

such as COM port, should be screwed after the I/O cable connectors are

completely connected. And please make sure that each connector has to be

connected to the right peripheral device in the right way.

CAUTION: On doing insertion or extraction of a cable connector, please

always hold the connector head itself instead of pulling the cable wire.

Doing this could damage the cables and ports, which is considered as an

artificial damage and is not covered by the warranty. The means of power

cord should be connected to a socket-outlet with earthing connection.

ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de

câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de

tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est

considéré comme un dommage artificiel et n'est pas couvert par la

garantie. Le cordon d'alimentation doit être connecté à une prise de

courant avec mise à la terre.

Routing and Arranging Cables

Gen 7E/8E bases feature their own cable management to help you well

organize the cords whenever you need to connect peripheral devices to XT-

7315/7515. The following provides some useful cable-routing instructions

required to manage your cables.

1. Set up your terminal in Full Extended

mode and then tilt the screen all the way

down.

17

2. Remove the cable cover.

3. Pull outwards the locking levers with your

forefingers and then remove the neck

cover in the direction shown by the arrow.

4. Tilt the screen to the horizontal position.

Thread the cables along the cable passage

and then through the cable exit.

5. Tilt the terminal up enough to have the bottom I/O plate

towards you. Locate the cable arrangement cover as shown in

the figure.

6. Remove the cable arrangement cover by

pushing it up in the direction shown by

the arrow.

7. Properly insert the cable into the correct

port on the bottom I/O plate.

Cable Arrangement Cover

18

8. Neatly arrange your cable. Then, make

sure the cord can be held into place and

passed through the cable exit after sliding

back the cable arrangement cover.

9. Have the screen tilt all the way down, and

then push the neck cover back into place.

10. Place the cable cover back.

11. Make sure the cable is threaded through the cable exit at the bottom

of the base.

Gen 7E base

Gen 8E base

Installing Optional Upgrade Kits and Peripherals

XT-7315/7515 is an expandable model which allows you to upgrade its own

capacity by additionally installing multiple peripheral devices, such as

magnetic stripe reader (MSR), LCD monitor, and cash drawer, according to

your preference. The following will give you installation instructions on how

to expand on your current POS system with these optional upgrade kits. Before

proceeding with the installation of peripherals, please make sure the POS

system is completely shut down to prevent damage.

Cable Exit

19

 Installing UPS Battery to Gen 8E Base

UPS battery compartment can be found at

the bottom of Gen 8E base as shown in the

figure. Please be advised that the installation

of UPS battery should be conducted by a

technician according to the user manual

specific to UPS battery.

 Installing PoweredUSB to Gen 8E Base

The middle compartment at the bottom of

Gen 8E base is designed to install

PoweredUSB. However, the installation of

PoweredUSB is required to be conducted

properly and accurately, so please contact

your service provider for help. The detailed

installation guide will be provided in the

relevant technical manual.

 Installing Power Adapter to Gen 8E Base

Power adapter is used to provide power which your terminal needs to be

operated normally. Please go through the below steps to install the power

adapter into Gen 8E base. If the power adapter is already installed to Gen

8E base, you may skip this section

1. Lay your POS terminal on a flat surface

with its bottom facing towards you.

2. Take the AC power adapter with its

rubber feet facing you. Place the bottom

side of the power adapter into the

bottom of the power adapter

compartment first, and then push the top

side of the adaptor into the

compartment.

20

3. After pushing the power adapter up to

the top, place two brackets separately on

the top and bottom sides of the power

adapter compartment as shown in the

figure. Then, fasten two brackets with

four fixing screws.

4. Before threading the cable through the cable exit, loosen two

fixing screws for the bracket of the PoweredUSB compartment.

Then, slide the bracket in the direction shown by the arrow to

remove the bracket.

5. Pass the cable of the power adapter

through the cable exit and then connect

it to the port on the I/O plate of your

POS system. (Please refer to Routing

and Arranging Cables section to thread

the cable, according to the model of

your base.)

Cable Exit

Bracket Power Adaptor

La page charge ...

Posiflex XT-7315/7515 Manuel utilisateur

Ce manuel convient également à

Posiflex XT-7315/7515 Manuel utilisateur

dans d''autres langues

Documents connexes