AT&T EL52106 Manuel utilisateur

User’s manual

EL50005

DECT 6.0 expansion handset

for use with AT&T models

EL52115/EL52145/EL52215/

EL52245/EL52265/EL52315/

EL52345/EL52365/EL52465/

EL52106/EL52206/EL52246/

EL52256/EL52306/EL52346/

EL52356/EL52406

Congratulations

on your purchase of this AT&T product. Before using this AT&T

product, please read the Important safety information section on

pages 21-23 of this manual. For complete instructions, please

refer to the manual provided with your EL52115/EL52145/EL52215/

EL52245/EL52265/EL52315/EL52345/EL52365/EL52465/EL52106/

EL52206/EL52246/EL52256/EL52306/EL52346/EL52356/EL52406

telephone.

You can also visit our website at www.telephones.att.com or

call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission regulations

for energy consumption. Your telephone is set up to comply with the

energy-conserving standards right out of the box. No further action

is necessary.

Model number: EL50005

Type: DECT 6.0 expansion handset

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be

found on the bottom of the telephone base.

Save your sales receipt and original packaging in case it is

necessary to return your telephone for warranty service.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Telephones identified with this logo have reduced noise and

interference when used with most T-coil equipped hearing

aids and cochlear implants. The TIA-1083 Compliant Logo is a

trademark of the Telecommunications Industry Association. Used

under license.

THIS SIDE UP / CE

CÔ

TÉ

VERS LE HA

UT

Battery Pack / Bloc-piles

:

BT162342/BT262342 (2.4V 3 00mAh Ni-MH

)

W

ARNING /

AV

ERTISSEMENT

:

DO NOT BURN OR PUNCTURE BA

TTERIES.

NE

PA

S INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1423

Parts checklist

Your telephone package contains the following items. Save your

sales receipt and original packaging in the event warranty service

is necessary.

Battery for

cordless handset

Cordless handset

Charger for cordless

handset with power

adapter installed

Battery

compartment

cover

User’s manual

EL50005

DECT 6.0 expansion handset

for use with AT&T models

EL52115/EL52145/EL52215/

EL52245/EL52265/EL52315/

EL52345/EL52365/EL52465/

EL52106/EL52206/EL52246/

EL52256/EL52306/EL52346/

EL52356/EL52406

User’s manual

EL50005

DECT 6.0 expansion handset

for use with AT&T models

EL52115/EL52145/EL52215/EL52245/EL52265/

EL52315/EL52345/EL52365/EL52465/

EL52106/EL52206/EL52246/EL52256/

EL52306/EL52346/EL52356/EL52406

Table of contents

Getting started

Installation ............................................................................................................................. 1

Quick reference guide ....................................................................................................2

Charger installation .........................................................................................................5

Battery installation and charging ..........................................................................6

Registration and deregistration

Adding and registering handsets ...........................................................................9

Register a handset to your telephone base ...............................................9

Deregistering handsets .............................................................................................. 11

Deregister all handsets from your telephone base.............................11

Appendix

Troubleshooting...............................................................................................................12

Maintenance ......................................................................................................................20

Important safety information ................................................................................21

Safety information .....................................................................................................21

Especially about cordless telephones .......................................................... 22

Precautions for users of implanted cardiac pacemakers .............. 23

Pacemaker patients ................................................................................................. 23

ECO mode ....................................................................................................................... 23

Especially about telephone answering systems...................................23

For C-UL compliance ....................................................................................................24

Mesures de sécurité importantes ..................................................................24

FCC Part 68 and ACTA ................................................................................................. 27

FCC Part 15 ..........................................................................................................................29

California Energy Commission battery charging testing

instructions ....................................................................................................................30

Limited warranty .............................................................................................................31

Technical specications .............................................................................................34

DECT 6.0 digital technology ................................................................................34

Telephone operating range ................................................................................34

Simulated full-duplex handset speakerphone ......................................34

1

See pages 6-8

for easy instructions.

You must install and

charge the battery before

using the telephone.

STOP!

Installation

Your product may be shipped with a protective sticker covering the

handset display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the charger too close to:

Communication devices such as television sets, VCRs, or other

cordless telephones.

Excessive heat sources.

Noise sources such as a window with trac outside, motors,

microwave ovens, refrigerators, or uorescent lighting.

Excessive dust sources such as a workshop or garage.

Excessive moisture.

Extremely low temperature.

Mechanical vibration or shock such as on top of a washing

machine or workbench.

•

Getting started

Quick reference guide

Getting started

2

light

On when the handset is charging in the

telephone base or charger.

Press to scroll up while in menus.

Press to show directory entries when the

handset is not in use.

When entering names or numbers in the

directory, press to move the cursor to

the right.

Press to increase the listening volume

when on a call; or to increase the message

playback volume.

•

Press to turn on the handset speakerphone,

press again to resume normal handset use.

Press to switch to tone dialing temporarily

during a call if you have pulse service.

Press to make or answer a call.

During a call, press to answer an incoming

call when you receive a call waiting alert.

•

While reviewing a caller ID log entry, press

repeatedly to add or remove 1 in front of

the telephone number before dialing or

saving it in the directory.

Press and hold to set or dial your

voicemail number.

•

Press repeatedly to view the last ten

numbers dialed.

While entering numbers, press and hold to

insert a dialing pause.

•

Quick reference guide

Getting started

3

Press to scroll down while in menus.

Press to show the caller ID log when the

handset is not in use.

While entering names or numbers in the

directory, press to move the cursor to

the le.

Press to decrease the listening volume

when on a call; or to decrease the message

playback volume.

•

Press to display the menu.

Once in the menu, press to select an item

or save an entry or setting.

•

During a call, press to hang up.

While using menus, press to cancel an

operation, back up to the previous menu,

or exit the menu display; or press and hold

to exit to idle mode.

Press and hold while the handset is not in

use to erase the missed call indicator.

•

Press and hold to set and turn on the quiet

mode, or turn it o.

When reviewing a caller ID log entry, press

repeatedly to view other dialing options.

•

During a call, press to mute the microphone.

While predialing, press to erase digits.

While reviewing the redial list, directory,

speed dial list or caller ID log, press to

delete an individual entry.

•

Press to initiate an intercom conversation or

transfer a call.

Quick reference guide

Getting started

4

For complete instructions, refer to the manual provided with your

EL52115/EL52145/EL52215/EL52245/EL52265/EL52315/EL52345/

EL52365/EL52465/EL52106/EL52206/EL52246/EL52256/

EL52306/EL52346/EL52356/EL52406 telephone system. If you are

unable to nd your manual, go to

www.telephones.att.com/manuals to read and/or download

the manual.

Main menu

Play messages

Answering sys

Directory

Caller ID log

Call block

Ringers

Set date/time

Settings

Using menus:

Press to show

the menu.

Press or

to scroll

through menu items.

Press to conrm or

save changes to a highlighted

menu item.

Press to cancel an

operation, back up to the previous

menu, or exit the menu display.

•

Play messages

ECO

IMPORTANT INFORMATION

1. Use only the power adapter supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or

call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapter is intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Plug the power adapter into an

electrical outlet not controlled by a

wall switch.

5

Charger installation

Install the charger, as shown below.

Getting started

6

Battery installation and charging

Install the battery as shown on pages 7-8. Once you have installed

the battery, the screen indicates the battery status (see the

following table). If necessary, place the handset in the telephone

base or charger to charge the battery. For best performance, keep

the handset in the telephone base or charger when not in use. The

battery is fully charged aer 16 hours of continuous charging. See

the table on page 34 for battery operating times.

If the screen shows Put in charger and ashes, you need to

charge the handset without interruption for at least 30 minutes to

give the handset enough charge to use the telephone for a short

time. The following table summarizes the battery charge indicators

and actions to take.

Getting started

Battery indicators Battery status Action

The screen is blank, or

shows Put in charger

and (ashing).

Battery has no or

very little charge. The

handset cannot be

used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and

(ashing).

Battery has enough

charge to be used for a

short time.

Charge without interruption

(at least 30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery

charged, place it in the

telephone base or charger

when not in use.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps

every 50 seconds.

Battery installation and charging

Getting started

7

Plug the battery connector securely into the socket inside the

handset battery compartment. Insert the supplied battery with

the label THIS SIDE UP facing up, as indicated.

Align the cover at against the battery compartment, then slide it

upwards until it clicks into place.

Charge the handset by placing it face up in the telephone base

or charger. The CHARGE light is on when charging.

1.

2.

3.

THI

S

I

DE UP

/

CE

CÔ

TÉ

VERS LE

HA

UT

Ba

t

er

y

Pack / Bloc-p

iles

:

BT16

2

342/BT262342 (2.4V 300mAh Ni-MH)

WA

RNING /

A

VE

RT

I

SSE

ME

NT

:

DO NOT BUR

N OR PU

N

CTURE BA

TTERIE

S.

NE

PA

S INCINÉRE

R

OU PE

R

CE

R LE

S

P

ILES

.

M

ade in

C

hina /

F

ab

r

iqué en chine

CR1423

THIS SIDE UP

Battery Pack

/ Bloc-pi

les

BT162342/

B

T262342 (2.4V

4

WA

RN

ING /

AV

ERTISSEMENT

DO NOT BURN OR

P

UNCTURE

B

NE

PA

S INCI

N

ÉRER OU PERC

E

R

L

M

ade in China / Fabriqué

e

n chine

CR142

3

7

CHARGE light

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery

(model BT162342/BT262342). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

2. If you do not use the handset for a long time, disconnect and remove

the battery to prevent possible leakage.

Aer you install your telephone or power returns following a power

outage, the handset will prompt you to set the date and time. Aer

that, it will prompt if you want to set up the answering system

via voice guide. Press to start. For details, see the

corresponding sections in the telephone system’s user’s manual. To

skip these settings, press .

Battery installation and charging

Getting started

8

To replace the battery, press the tab and

slide the battery compartment cover

downwards. Li out the old battery and

disconnect it from the handset. Follow

the instructions to install and charge a

new battery.

Adding and registering handsets

Before using a new EL50005 handset, you must register it with

the AT&T EL52115/EL52145/EL52215/EL52245/EL52265/EL52315/

EL52345/EL52365/EL52465/EL52106/EL52206/EL52246/

EL52256/EL52306/EL52346/EL52356/EL52406 telephone system

(purchased separately). The telephone system can support up to

ve handsets.

The handset(s) provided with your telephone system are already

registered as HANDSET 1, and so forth. Additional handsets are

assigned numbers in the sequential order they are registered (up

to HANDSET 5). Each handset must be registered to the telephone

base before use.

Register a handset to your telephone base

1. Before you begin registration, make sure the handset is out of

the telephone base or charger and shows To register HS... and

...see manual, alternately.

2. Put the handset you wish to register on the telephone

base cradle.

Registration and deregistration

9

For registration, put the handset on the

telephone base, not the handset charger.

Adding and registering handsets

3. The light on the telephone base turns on. Aer about

10 seconds, the handset shows Registering.... The handset

shows Registered and you hear a conrmation tone if the

registration was successful. The light turns o. The

handset is now registered with the telephone base.

If the registration fails, the handset displays Reg. failed and then

To register HS... and ...see manual, alternately. Try the registration

again by removing the handset from the telephone base and then

placing it back in.

NOTES:

You cannot register a handset if any other system handset is in use.

You can only register one handset to the telephone base at a time.

•

Registration and deregistration

10

Deregistering handsets

If you want to replace a handset, or reassign the designated

handset number of a registered handset, you must deregister

all handsets that are registered to the telephone base, and then

register each handset individually.

Please read carefully through all the instructions on this page

before beginning the deregistration process.

Deregister all handsets from your telephone base

In addition to the cordless handsets, this operation will also

deregister all cordless headsets and speakerphones registered to

your telephone base.

Press and hold or on the

telephone base for about 10 seconds until the light on

the telephone base turns on and starts to ash. Then, release

the button.

Immediately press or again

while the light is still ashing. The light ashes for

approximately ve seconds.

The deregistration takes about 10 seconds to complete. All

handsets display To register HS... and ...see manual, alternately,

if the deregistration was successful.

To register the handset(s) to the telephone base again, follow the

registration instructions on pages 9-10.

NOTES:

If the deregistration fails, you may need to reset the system and try again. To reset,

unplug the power from the telephone base and plug it back in.

You cannot deregister the handset(s) if any other system handset is in use.

Even if the battery is depleted, you can still deregister the handset by following the

steps, as mentioned above. After the handset is charged for at least ten minutes,

the screen shows To register HS... and ...see manual, alternately.

1.

2.

3.

•

Registration and deregistration

11

Troubleshooting

If you have diculty with your phone, please try the following

suggestions. For Customer Service, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

The handset registration is unsuccessful.

Follow the handset registration instructions to register the handset

again (see Adding and registering handsets on pages 9-10).

My telephone doesn’t work at all.

Make sure the power cord is securely plugged in.

Make sure you plug the battery connector securely into the

cordless handset.

Make sure you plug the telephone line cord securely and rmly

into the telephone base and the telephone wall jack.

Charge the battery in

the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it might take approximately 30 minutes

to charge the handset before it shows Low battery. See page 6

for details.

Reset the telephone base. Unplug the electrical power. Wait for

approximately 15 seconds, then plug it back in. Allow up to one

minute for the cordless handset and telephone base to reset.

You may need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-8.

The display shows No line. I cannot get a dial tone.

Try all the suggestions mentioned above.

If the previous suggestions do not work, disconnect the

telephone line cord from your telephone and connect the

telephone line cord to another telephone.

If there is no dial tone on that other telephone either, your

telephone line cord may be defective. Install a new telephone

line cord.

•

Appendix

12

Troubleshooting

Appendix

13

If changing the telephone line cord does not help, the wall

jack (or the wiring to this wall jack) may be defective. Try

using a dierent wall jack in your home to connect your

EL52115/EL52145/EL52215/EL52245/EL52265/EL52315/

EL52345/EL52365/EL52465/EL52106/EL52206/EL52246/

EL52256/EL52306/EL52346/EL52356/EL52406 telephone, or

contact your telephone service provider (charges may apply).

I cannot dial out.

Try all the suggestions mentioned above.

Make sure you have a dial tone before dialing. The cordless

handset might take a second or two to nd the telephone base

and produce a dial tone. This is normal. Wait an extra second

before dialing.

Eliminate

any background noise. Noise from a television, radio or

other appliances might cause the phone to not dial out properly.

If you cannot eliminate the background noise, try muting the

cordless handset before dialing, or dialing from another room

with less background noise.

If other phones in your home are having the same problem,

contact your telephone service provider (charges might apply).

My cordless handset isn’t performing normally.

Make sure you plug the power cord securely into the telephone

base. Plug the power adapter into a dierent, working electrical

outlet without a wall switch.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

•

Troubleshooting

Appendix

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Out of range or no pwr at base appears on my cordless handset.

Ensure you plug the telephone base in properly and the power is on.

Place the cordless handset in the telephone base for one minute

to allow the cordless handset and base to synchronize.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

The batteries do not hold a charge.

If the cordless handset is in the telephone base or charger

and the charge light is not on, refer to The charge light is o

(page 19) in this Troubleshooting guide.

Charge the battery in the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it might take approximately 30 minutes to

charge the handset before it shows Low battery. Refer to the table

on page 6 for details.

You might need to purchase a new battery. Refer to Battery

installation and charging in this user’s manual on pages 6-8.

I hear other calls while using my phone.

Disconnect the telephone base from the telephone jack, and

plug in a different telephone. If you still hear other calls, call

your telephone service provider.

•

14

I get noise, static, or weak signals even when I’m near the

telephone base.

If you subscribe to high-speed Internet service (DSL - digital

subscriber line) through your telephone line, you must install a

DSL lter between the telephone line cord and the telephone

wall jack. The lter prevents noise and caller ID problems as

a result of DSL interference. Please contact your DSL service

provider for more information about DSL lters.

You may be able to improve the performance of your cordless

phone by installing your new telephone base as far as possible

from any other existing cordless telephone system that may

already be installed.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Do not install this phone near a microwave oven or on the same

electrical outlet. You might experience decreased performance

while the microwave oven is operating.

If you plug your phone in with a modem or a surge protector,

plug the phone (or modem/surge protector) into a dierent

location. If this does not solve the problem, relocate your phone

or modem farther apart from one another, or use a dierent

surge protector.

Move your phone to a higher location. The phone might have

better reception in a high area.

If the other phones in your home are having the same problem,

contact your telephone service provider (charges may apply).

I experience poor sound quality when using the speakerphone.

For increased sound quality while using the speakerphone, place

the handset on a at surface with the dialing keys facing up.

•

Troubleshooting

Appendix

15

My cordless handset does not ring when I receive a call.

Make sure that the ringer is not o. Refer to Ringer volume

in the user’s manual provided with your EL52115/EL52145/

EL52215/EL52245/EL52265/EL52315/EL52345/EL52365/

EL52465/EL52106/EL52206/EL52246/EL52256/EL52306/

EL52346/EL52356/EL52406 telephone.

Make sure you plug the telephone line cord securely into the

telephone base and telephone jack. Make sure you plug in the

power cord securely.

The cordless handset may be too far from the telephone base.

Charge the battery in the cordless handset for at least 10 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

You may have too many extension phones on your telephone

line to allow all of them to ring simultaneously. Try unplugging

some of the other phones.

The layout of your home or oce might be limiting the

operating range. Try moving the telephone base to another

location, preferably on an upper oor.

If the other phones in your home are having the same problem,

contact your telephone service provider (charges might apply).

Test a working phone at the phone jack. If another phone has

the same problem, contact your telephone service provider

(charges might apply).

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

Completely remove the battery. Replace it and place the

cordless handset into the telephone base. Allow up to one

minute for the handset to reestablish its connection with the

telephone base.

Your line cord might be defective. Try installing a new line cord.

•

Troubleshooting

Appendix

16

La page charge ...

AT&T EL52106 Manuel utilisateur

Ce manuel convient également à

AT&T EL52106 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents