Samsung BD-J5900 Manuel utilisateur
- Catégorie
- Lecteurs Blu-Ray
- Taper
- Manuel utilisateur
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray
™
Disc Player
user manual
BD-J5900
ENGLISH
Safety Information
Warning
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER (OR
BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
This symbol indicates that high
voltage is present inside. It is
dangerous to make any kind of
contact with any internal part of
this product.
This symbol indicates that
important literature concerning
operation and maintenance has
been included with this product.
•
The slots and openings in the cabinet and
in the back or bottom are provided for
necessary ventilation. To ensure reliable
operation of this apparatus, and to protect it
from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a confined
space, such as a bookcase, or built-
in cabinet, unless proper ventilation is
provided.
- Do not place this apparatus near or over
a radiator or heat register, or where it is
exposed to direct sunlight.
- Do not place vessels (vases etc.) containing
water on this apparatus. A water spill can
cause a fire or electric shock.
•
Do not expose this apparatus to rain or place
it near water (near a bathtub, washbowl,
kitchen sink, or pool, etc.). If this apparatus
accidentally gets wet, unplug it and contact
an authorized dealer immediately.
•
This apparatus uses batteries. In
your community, there might be
environmental regulations that require you
to dispose of these batteries properly.
Please contact your local authorities for
disposal or recycling information.
•
Do not overload wall outlets, extension
cords or adaptors beyond their capacity,
since this can result in fire or electric shock.
•
Route power-supply cords so that they
are not likely to be walked on or pinched
by items placed on or against them. Pay
particular attention to cords at the plug end,
at wall outlets, and the point where they exit
from the apparatus.
•
To protect this apparatus from a lightning
storm, or when it is left unattended and
unused for long periods of time, unplug
it from the wall outlet and disconnect the
antenna or cable system. This will prevent
damage to the set due to lightning and
power line surges.
•
Before connecting the AC power cord to the
DC adaptor outlet, make sure the voltage
designation of the DC adaptor corresponds
to the local electrical supply.
•
Never insert anything metallic into the open
parts of this apparatus. Doing so may create
a danger of electric shock.
•
To avoid electric shock, never touch the
inside of this apparatus. Only a qualified
technician should open this apparatus.
•
Make sure to plug the power cord in until it
is firmly seated. When unplugging the power
cord from a wall outlet, always pull on the
power cord's plug. Never unplug by pulling
on the power cord. Do not touch the power
cord with wet hands.
•
If this apparatus does not operate normally
- in particular, if there are any unusual
sounds or smells coming from it - unplug
it immediately and contact an authorized
dealer or service center.
•
Maintenance of Cabinet.
- Before connecting other components to
this product, be sure to turn them off.
- If you move your product suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and
lens and cause abnormal disc playback.
If this occurs, unplug the product, wait
for two hours, and then connect the plug
to the power outlet. Then, insert the disc,
and try to play back again.
•
Be sure to pull the power plug out of the
outlet if the product is to remain unused or
if you are leaving the house for an extended
period of time (especially when children,
elderly, or disabled people will be left alone
in the house).
- Accumulated dust can cause an electric
shock, an electric leakage, or a fire by
causing the power cord to generate
sparks and heat or the insulation to
deteriorate.
•
Contact an authorized service center for
information if you intend to install your
product in a location with heavy dust, high
or low temperatures, high humidity, chemical
substances, or where it will operate 24
hours a day such as in an airport, a train
station, etc. Failing to do so may lead to
serious damage of your product.
•
Use only a properly grounded plug and wall
outlet.
- An improper ground may cause electric
shock or equipment damage. (Class l
Equipment only.)
•
To turn this apparatus off completely, you
must disconnect it from the wall outlet.
Consequently, the wall outlet and power
plug must be readily accessible at all times.
•
Do not allow children to hang on the
product.
•
Store the accessories (battery, etc.) in a
location safely out of the reach of children.
•
Do not install the product in an unstable
location such as a shaky self, a slanted floor,
or a location exposed to vibration.
•
Do not drop or strike the product. If the
product is damaged, disconnect the power
cord and contact a service center.
•
To clean this apparatus, unplug the power
cord from the wall outlet and wipe the
product using a soft, dry cloth. Do not
use any chemicals such as wax, benzene,
alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals
can damage the appearance of the product
or erase the printing on the product.
•
Do not expose this apparatus to dripping
or splashing. Do not put objects filled with
liquids, such as vases on the apparatus.
•
Do not dispose of batteries in a fire.
•
Do not plug multiple electric devices into the
same wall socket. Overloading a socket can
cause it to overheat, resulting in a fire.
•
There is danger of an explosion if you
replace the batteries used in the remote with
the wrong type of battery. Replace only with
the same or equivalent type.
•
WARNING - TO PREVENT
THE SPREAD OF FIRE,
KEEP CANDLES AND
OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
2
FCC NOTE (for U.S.A)
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on.
The user is encouraged to try to correct the
interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the
equipment and receiver.
•
Connecting this equipment into an outlet
on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/
TV technician for help.
This class B digital product meets all
requirements of the Canadian Interference -
Causing Equipment Regulations.
Note to CATV system installer
This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the
National Electrical Code (Section 54 of Canadian
Electrical Code, Part I) that provides guidelines
for proper grounding and, in particular, specifies
that the cable ground shall be connected to the
grounding system of the building as close to the
point of cable entry as practical.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product. Use of controls,
adjustments or performance of procedures
other than those specified herein may result in
hazardous radiation exposure.
DANGER :
•
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM. (FDA 21 CFR)
CAUTION :
•
CLASS 3B VISIBLE AND INVISIBLE
LASER RADIATION WHEN OPEN. AVOID
EXPOSURE TO THE BEAM. (IEC 60825-1)
•
THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND
DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
✎
NOTES
`
If the Region number of a Blu-ray Disc/DVDs
does not correspond to the Region number of
this product, the product cannot play the disc
.
Precautions
Important Safety Instructions
Read these operating instructions carefully
before using the unit. Follow all the safety
instructions listed below.
Keep these operating instructions handy for
future reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including AV receivers)
that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong
are provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where it exits the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the
cart, stand, tripod,
bracket, or table
specified by the
manufacturer,
or sold with the
apparatus. When a
cart is used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally, or
has been dropped.
3
• To reduce the risk of fire or electric shock,
do not expose this appliance to rain or moisture.
Contents
Using the 3D function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES. Read and
understand the following safety information
before using the 3D function.
•
Some viewers may experience discomfort
while viewing 3D TV such as dizziness,
nausea, and headaches.
If you experience any such symptom,
stop viewing 3D TV, remove the 3D Active
Glasses, and rest.
•
Watching 3D images for an extended period
of time may cause eye strain. If you feel eye
strain, stop viewing 3D TV, remove your 3D
Active Glasses, and rest.
•
A responsible adult should frequently check
on children who are using the 3D function.
If there are any reports of tired eyes,
headaches, dizziness, or nausea, have the
child stop viewing 3D TV and rest.
•
Do not use the 3D Active Glasses for other
purposes (Such as general eyeglasses,
sunglasses, protective goggles, etc.).
•
Do not use the 3D function or 3D Active
Glasses while walking or moving around.
Using the 3D function or 3D Active Glasses
while moving around may cause you to
bump into objects, trip, and/or fall, and
cause serious injury.
•
If you want to enjoy 3D content, connect
a 3D device (3D compliant AV receiver or
TV) to the player's HDMI OUT port using a
high-speed HDMI cable. Put on 3D glasses
before playing the 3D content.
•
The player outputs 3D signals only through
HDMI cable connected to the HDMI OUT
port.
•
As the video resolution in 3D play mode
is fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
•
Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
•
You must use a high-speed HDMI cable for
proper output of the 3D signal.
•
Stay at least three times the width of the
screen from the TV when watching 3D
images. For example, if you have a 46-inch
screen, stay 138 inches (11.5 feet) from the
screen.
•
Place the 3D video screen at eye level for
the best 3D picture.
•
When the player is connected to some 3D
devices, the 3D effect may not function
properly.
•
This player does not convert 2D content into
3D.
•
"Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
SAFETY INFORMATION
Warning ..................................................... 2
Precautions ............................................... 3
Using the 3D function ................................ 4
GETTING STARTED
Before using the User Manual .................... 5
Logos of Discs the player can play ............ 5
Accessories ............................................... 7
Front Panel ................................................ 7
Rear Panel ................................................. 7
Remote Control ......................................... 8
CONNECTIONS
Connecting to a TV .................................... 8
Connecting to an Audio System ................ 9
Connecting to a Network Router ............... 9
SETTINGS
The Setup Procedure ............................... 10
Menu Navigation ...................................... 10
Accessing the Settings Menu .................. 11
Picture Settings ....................................... 11
Sound Settings ........................................ 12
Network Settings ..................................... 13
System Settings ...................................... 16
Language Settings ................................... 17
Security Settings...................................... 17
General Settings ...................................... 17
Support Settings ..................................... 18
MEDIA PLAY
Playing a Commercially Recorded Disc .... 19
Playing Files on a USB Device ................. 19
Playing a Disc with User Recorded
Content ................................................... 19
Using DLNA ............................................. 20
Controlling Video Playback ...................... 20
Controlling Music Playback ...................... 21
Playing Photo Contents ........................... 22
APPENDIX
Troubleshooting ....................................... 23
Specifications .......................................... 24
4
Getting Started
Before using the User Manual
Disc Types and Contents your player can play
Media Disc Type Details
VIDEO
Blu-ray Disc
3D Blu-ray Disc
BD-ROM or BD-RE/-R recorded in the BD-RE format.
DVD-VIDEO
DVD-RW
DVD-R
DVD+RW
DVD+R
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R that
have been recorded and finalized, or a USB storage media
containing MKV or MP4 contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a
USB storage media containing MP3 or WMA contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R or a
USB storage media containing JPEG contents.
✎
NOTES
`
The player may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
`
If a DVD-RW/-R has not been recorded properly in DVD video format, it will not be playable.
`
Your player will not play content that has been recorded on a DVD-R at a bit-rate that exceeds 10 Mbps.
`
Your player will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds
25 Mbps.
`
Playback may not work for some types of discs, or when you use specific functions, such as angle change
and aspect ratio adjustment. Information about the discs is written in detail on the disc box. Please refer to
this if necessary.
`
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your player cannot play
• HD DVD
• DVD-ROM/PD/
MV, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
•
DVD-RW (VR mode)
•
CVD/CD-ROM/CDV/
CD-G/CD-I/LD (CD-
Gs play audio only, not
graphics.)
• 3.9 GB DVD-R
for Authoring.
Region Code
Both players and discs are coded by region.
These regional codes must match for a disc
to play. If the codes do not match, the disc will
not play.
The Region Code for this player is displayed on
the rear panel of the player.
Disc Type
Region
Code
Area
Blu-ray
Disc
A
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia,
Central and South Asia.
DVD-
VIDEO
1
The U.S., U.S. territories
and Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the
Philippines, Indonesia,
Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific
Islands, Caribbean
5
Russia, Eastern Europe,
India, North Korea, Mongolia
6
China
Logos of Discs the player
can play
Blu-ray Disc BD-LIVE
3D Blu-ray Disc
NTSC broadcast system
in U.S.A, Canada, Korea,
Japan
Supported File Formats
Notes on the USB connection
•
Your player supports USB storage media,
MP3 players, digital cameras, and USB card
readers.
•
The player does not support folder or file
names longer than 128 characters.
•
Some USB/External HDD/digital camera
devices may not be compatible with the
player.
•
Your player supports the FAT16, FAT32, and
NTFS file systems.
•
Connect USB devices directly to the player’s
USB port. Connecting through a USB cable
may cause compatibility problems.
•
Inserting more than one memory device into
a multi-card reader may cause the reader to
operate improperly.
•
The player does not support the PTP
protocol.
•
Do not disconnect a USB device during a
"loading" process.
5
•
The bigger the image resolution, the longer the image takes to display.
•
This player cannot play MP3 files with DRM (Digital Rights Management) downloaded from
commercial sites.
•
Your player only supports video with a frame rate under 30fps (frames per second).
•
Your player only supports USB Mass Storage Class (MSC) devices such as thumb drives and
USB HDD. (HUB is not supported.)
•
Certain USB HDD Devices, multi-card readers and thumb drives may not be compatible with
this player.
•
If some USB devices require excessive power, they may be limited by the circuit safety device.
•
If playback from a USB HDD is unstable, provide additional power by plugging the HDD into a
wall socket.
If the problem continues, contact the USB HDD manufacturer.
•
SAMSUNG is not responsible for any data file damage or data loss.
•
Your player does not support NTFS compressed files, sparse files, or encrypted files.
•
You can repair or format a USB device on your Desktop PC. (MS-Windows OS only)
Video File Support
File Extension Container Video Codec Audio Codec Resolution
*.avi
AVI
MP4v3
MP3
Dolby Digital
DTS
WMA
PCM
1920x1080
H.264 BP/MP/HP
1920x1080
*.mkv
MKV
VC-1 AP
MP3
Dolby Digital
DTS
1920x1080
H.264 BP/MP/HP
1920x1080
*.wmv
WMV (wmv9)
VC-1 AP
WMA
1920x1080
VC-1 SM
1920x1080
*.mp4
MP4
MP4 (mp4v)
AAC
1920x1080
H.264 BP/MP/HP
1920x1080
*.mpg
*.mpeg
MPEG
MPEG1
MP1, 2
Dolby Digital
DTS
1920x1080
MPEG2
1920x1080
H.264 BP/MP/HP
1920x1080
• Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be played
if its content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file itself
is corrupted.
- Files having a higher Bit rate/frame rate than standard may stutter during sound/video playback.
- The Seek (skip) function is not available if the file’s index table is damaged.
• Video decoder
- Supports up to H.264 Level 4.1 and AVCHD
- Does not support H.264 FMO/ASO/RS and VC1 SP/MP/AP L4
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
• Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA sampling rate of 22050Hz mono.
- AAC: Max sampling rate: 96Khz (8, 11, 12, 16, 22,24, 32,44.1, 48, 64, 88.2, 96)
Max bitrate: 320kbps
Music File Support
File Extension Container Audio Codec Support Range
*.mp3
MP3 MP3
-
*.wma
WMA WMA
* Sampling rates (in kHz) - 8, 11, 16, 22, 32, 44.1, 48
* Bit rates - All bit-rates from 5kbps to 355kbps
Picture File Support
File Extension Type Resolution
*.jpg
*.jpeg
*.jpe
JPEG
15360x8640
*.png
PNG
15360x8640
6
AVCHD (Advanced Video Codec High Definition)
• This player can play back AVCHD format discs. These discs are normally recorded and
used in camcorders.
• The AVCHD format is a high definition digital video camera format.
• The MPEG-4 AVC/H.264 format compresses images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the "x.v.Color" format. This player can play back AVCHD discs
that use "x.v.Color" format.
• "x.v.Color" is a trademark of Sony Corporation.
• "AVCHD" and the AVCHD logo are trademarks of Matsushita Electronic Industrial Co., Ltd.
and Sony Corporation.
✎
NOTES
`
Some AVCHD format discs may not play, depending on the recording condition.
AVCHD format discs need to be finalized.
`
"x.v.Color" offers a wider color range than normal DVD camcorder discs.
Accessories
Check for the supplied accessories shown below.
SCREEN
VIEW A-B
FULLBONUS REPEAT REPEAT
Batteries for Remote Control
(AAA Size)
User Manual Remote Control
Front Panel
DISC TRAY
POWER BUTTON
OPEN/CLOSE BUTTON
USB HOST
REMOTE CONTROL SENSOR
✎
NOTES
`
You can perform software upgrades using the USB Host jack with a USB flash memory stick only.
`
Please open and pull out the USB cover before inserting USB device.
Rear Panel
HDMI OUT LAN DIGITAL AUDIO OUT
7
Remote Control
Tour of the Remote Control
SCREEN
VIEW A-B
FULLBONUS REPEAT REPEAT
Turn the player on and off.
Allows you to repeat A-B disc.
Press the number buttons to operate options.
Press to open and close the disc tray.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use bonusview function.
Return to the previous menu.
These buttons are used both for menus on the
player and also several Blu-ray Disc functions.
Use to select menu items and change menu
values.
Press to use the Tools menu.
Use to access various audio functions on a
disc (Blu-ray Disc/DVD).
Press to play a disc.
Press to pause a disc.
Turn the TV on and off.
Press to switch the Blu-ray Disc/DVD’s
subtitle language.
Use to enter the popup menu/title menu.
Press to search a disc backwards or
forwards.
Press to move to the Home menu.
Press to see the full screen on a TV.
During the Blu-ray Disc/DVDs playback, Full
Screen button does not operate.
Press to exit the menu.
Use to display the playback information
when playing a Blu-ray Disc/DVDs.
Allows you to repeat a title, chapter, track or
disc.
TV volume adjustment.
After setup, allows you to set the input
source on your TV.
Installing batteries
✎
NOTES
`
If the remote does not operate properly:
•
Check the polarity (+/–) of the batteries.
•
Check if the batteries are drained.
•
Check if the remote sensor is blocked by
obstacles.
•
Check if there is any fluorescent lighting nearby.
!
CAUTION
`
Dispose of batteries according to local
environmental regulations. Do not put them in
the household trash.
`
Do not dispose of batteries in a fire.
`
Do not short circuit, disassemble or overheat
the batteries.
`
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Connections
Connecting to a TV
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of
the product to the HDMI IN jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the
other connections.
- When you change the connections, turn off all devices before you start.
Audio
Video
✎
NOTES
`
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the Digital Audio
Out on the player to an audio system to hear audio.
`
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
`
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your
TV.
`
When you connect the player to your TV using the HDMI cable or to a new TV, and then turn it on for the first
time, the player automatically sets the HDMI output resolution to the highest supported by the TV.
`
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the menu.
`
To view video in the HDMI 720p, 1080i, or 1080p output mode, you must use a High speed HDMI cable.
`
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the
screen.
8
Connecting to an Audio System
You can connect the Blu-ray player to an audio system using one of the methods
illustrated below.
- Do not connect the power cord to the wall outlet until you have made all the other
connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI compatible AV receiver
•
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of
the product to the HDMI IN jack on your receiver.
•
Best quality (Recommended)
Method 2 Connecting to an AV receiver with a Digital Coaxial Cable
•
Using a digital Coaxial cable (not supplied), connect the Coaxial Digital Audio Out
jack on the product to the Digital Coaxial In jack of the receiver.
•
Good quality
•
You will hear sound only through the front two speakers with Digital Output set to
PCM.
AudioAudio
Method 2Method 1
Connecting to a Network Router
You can connect your player to your network router using one of the methods
illustrated below.
To use the DLNA network functionality, you must connect your PC to your network
as shown in the illustrations.
The connection can be wired or wireless.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
✎
NOTES
`
Internet access to Samsung's software update server may not be allowed, depending on the router you use
or your ISP's policy. For more information, contact your ISP (Internet Service Provider).
`
DSL users, please use a router to make a network connection.
9
Wireless Network
Wireless Router
Broadband service
✎
NOTES
`
If your wireless router supports DHCP, this player can use a DHCP or static IP address to connect to the
wireless network.
`
Set your wireless router to Infrastructure mode. Ad-hoc mode is not supported.
`
The player supports only the following wireless security key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES)
`
Select a channel on the wireless router that is not currently being used. If the channel set for the wireless
router is currently being used by another device nearby, it will result in interference and communication
failure.
`
If you select the Pure High-throughput (Greenfield) 802.11n mode and set the Encryption type on your router
to WEP, TKIP or TKIP-AES (WPS2Mixed), the player will not support a connection in compliance with new Wi-
Fi certification specifications.
`
Wireless LAN, by its nature, may cause interference, depending on the operating conditions (router
performance, distance, obstacles, interference by other radio devices, etc).
Settings
The Setup Procedure
•
The Home screen will not appear if you
do not configure the Setup.
•
The OSD (On Screen Display) may
change in this player after you upgrade
the software version.
•
The access steps may differ depending
on the menu you selected.
•
After the Setup process is complete, you
can then operate the panel buttons and
remote control.
After you have connected the player to
your TV, turn on the TV and player. When
you turn on the player the first time, the
player's Setup screen appears on the
TV. The Setup procedure lets you set
the On Screen Display (OSD) and menu
languages, the aspect ratio (screen size),
the network type, and connect the player
to your network.
✎
NOTES
`
The Home menu will not appear if you do not
configure the Setup except as noted below.
`
If you press the BLUE (D) button during network
setup, you can access the Home menu even if
the network setup is not completed yet.
`
When you return to the Home menu, the full
screen mode is cancelled automatically.
`
If you want to display the Setup screen again
to make changes, press the
^
button on
the front panel of the player for more than 5
seconds with no disc inserted. This resets the
player to its default settings.
`
After the Setup process is complete, you can
operate the HDMI-CEC function.
`
If you want to use the Anynet+(HDMI-CEC)
function to aid in the initial set up process,
please follow the instructions below.
1) Connect the player to an Anynet+(HDMI-CEC)
compliant Samsung TV using HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in
both the TV and the player.
3) Set the TV to the Setup Procedure.
`
If you leave the player in the stop mode for more
than 5 minutes without using it, a screen saver
will appear on your TV. If the player is left in the
screen saver mode for more than 25 minutes,
the power will automatically turn off.
Menu Navigation
SCREEN
VIEW A-B
FULLBONUS REPEAT REPEAT
1
2
4
3
1
HOME Button : Press to move to the
Home menu.
2
RETURN Button :
Return to the previous menu.
3
v
(Enter) / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current
menu.
10
• Home Menu
App 1 App 2 App 3 App 4
App 5
More
Screen Mirroring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
2
3
7
6
8
1
4
5
9
1
Selects VIDEOS.
2
Selects MUSIC.
3
Selects Settings.
4
Selects Change Device.
5
Selects Screen Mirroring.
6
Selects PHOTOS.
7
Selects PLAY DISC.
8
Selects applications.
9
Selects More applications.
✎
NOTES
`
The Videos, Photos, and Music options
require that you have an appropriate disc
inserted into the player or a USB flash
device attached to the player.
Accessing the Settings Menu
To access the Settings menu and sub-
menus, follow these steps:
1.
Press the POWER button.
The Home Menu appears.
2.
Press the ▲▼◄► buttons to select
Settings, and then press the
v
button.
3.
Press the ▲▼ buttons to select the
desired submenu, and then press
the
v
button.
4.
Press the ▲▼ buttons to select the
desired item, and then press the
v
button.
5.
Press the EXIT button to exit the menu.
✎
NOTES
`
The access steps may differ depending on
the menu you selected. The OSD (On Screen
Display) may change in this player after you
upgrade the software version.
Picture Settings
You can configure various display
options such as the TV Aspect Ratio,
Resolution, etc.
3D Settings
Select whether to play a Blu-ray Disc
with 3D contents in 3D Mode.
✎
NOTES
`
For some 3D discs, to stop a movie during 3D
playback, press the
5
button once.
The movie stops and the 3D mode option is
de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the
5
button once.
The Blu-ray menu appears. Press the
5
button again, then select 3D Settings in the
Blu-ray menu.
`
Depending on the content and the position of
the picture on your TV screen, you may see
vertical black bars on the left side, right side,
or both sides.
TV Aspect Ratio
Depending on the type of television you
have, you may want to adjust the screen
size setting.
✎
NOTES
`
Depending on the disc type, some aspect
ratios may not be available.
`
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
BD Wise (Samsung TVs only)
BD Wise is Samsung’s latest inter-
connectivity feature.
When you connect a Samsung player
and a Samsung TV with BD Wise to each
other via HDMI, and BD Wise is on in
both the player and TV, the player outputs
video at the video resolution and frame
rate of the Blu-ray Disc/DVDs.
✎
NOTES
`
When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
`
If the player is connected to a device that does
not support BD Wise, you cannot use the BD
Wise function.
`
For proper operation of BD Wise, set the BD Wise
menu of both the player and the TV to On.
Resolution
Lets you set the output resolution of the HDMI
video signal to Auto, 1080p, 1080i, 720p or
480p. The number indicates the number of
lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively.
The more lines, the higher the quality.
Resolution according to the output
mode
• Blu-ray Disc/E-contents/Digital
Contents playback
Output
Setup
HDMI / connected
HDMI Mode
Blu-ray Disc
E-contents/
Digital contents
BD Wise
Resolution of
Blu-ray Disc
1080p
Auto
Max. Resolution
of TV input
Max. Resolution
of TV input
1080p@60F
(Movie Frame : Off)
1080p@60F 1080p@60F
Movie Frame :
Auto (24Fs)
1080p@24F 1080p@24F
1080i 1080i 1080i
720p 720p 720p
480p 480p 480p
• DVD playback
Output
Setup
HDMI / connected
HDMI Mode
BD Wise 480i
Auto Max. Resolution of TV input
1080p 1080p
1080i 1080i
720p 720p
480p 480p
11
✎
NOTES
`
If the TV you connected to the player does
not support Movie Frame or the resolution
you selected, the message "If no pictures are
shown after selecting ‘Yes’, please wait for 15
seconds to return to the previous resolution."
appears. If you select Yes, the TV’s screen
will go blank for 15 seconds, and then the
resolution will revert to the previous resolution
automatically.
`
If the screen stays blank after you have
changed the resolution, remove all discs,
and then press and hold the
^
button on the
front of the player for more than 5 seconds.
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
`
When the factory default settings are restored,
all stored user BD data is deleted.
`
The Blu-ray Disc must have the 24 frame
feature for the player to use the Movie Frame
(24Fs) mode.
Movie Frame (24Fs)
Setting the Movie Frame (24Fs) feature
to Auto allows you to adjust the player’s
HDMI output to 24 frames per second
for improved picture quality.
You can enjoy the Movie Frame (24Fs)
feature only on a TV supporting this
frame rate. You can select Movie Frame
only when the player is in the HDMI
1080p output resolution modes.
HDMI Color Format
Lets you set the color space format for
HDMI output to match the capabilities of
the connected device (TV, monitor, etc).
HDMI Deep Color
Lets you output video from the HDMI
OUT jack with Deep Color. Deep
Color provides more accurate color
reproduction with greater color depth.
Progressive Mode
Lets you improve picture quality when
viewing DVDs.
Sound Settings
Digital Output
Lets you select the digital audio output
format that is suitable for your TV or
AV Receiver. For more details, please
refer to the Digital Output Selection
table below.
Digital Output Selection
Setup PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded Dolby
D)
Connection
HDMI
Receiver
Coaxial
HDMI
Receiver
Coaxial
HDMI Receiver or
Coaxial
HDMI supported
AV receiver or
Coaxial
Audio Stream
on Blu-ray
Disc
PCM Up to 7.1ch PCM 2ch PCM PCM 2ch Re-encoded DTS
Re-encoded Dolby
Digital *
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Re-encoded DTS
Re-encoded Dolby
Digital *
Dolby Digital
Plus
PCM 2ch PCM 2ch
Dolby Digital
Plus
Dolby Digital Re-encoded DTS
Re-encoded Dolby
Digital *
Dolby TrueHD PCM 2ch PCM 2ch Dolby TrueHD Dolby Digital Re-encoded DTS
Re-encoded Dolby
Digital *
DTS PCM 2ch PCM 2ch DTS DTS Re-encoded DTS
Re-encoded Dolby
Digital *
DTS-HD High
Resolution Audio
PCM 2ch PCM 2ch
DTS-HD High
Resolution Audio
DTS Re-encoded DTS
Re-encoded Dolby
Digital *
DTS-HD Master
Audio
PCM 2ch PCM 2ch
DTS-HD
Master Audio
DTS Re-encoded DTS
Re-encoded Dolby
Digital *
Audio Stream
on DVD
PCM PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch PCM 2ch
Dolby Digital PCM 2ch PCM 2ch Dolby Digital Dolby Digital Dolby Digital Dolby Digital
DTS PCM 2ch PCM 2ch DTS DTS DTS DTS
Definition for
Blu-ray Disc
Any
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and add
Navigation Sound Effects.
Outputs only main feature
audio stream so that your
AV receiver can decode the
audio bitstream.
You will not hear
BONUSVIEW audio and
Navigation Sound Effects.
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio
and add Navigation
Sound Effects, then
re-encodes the
PCM audio into DTS
bitstream
Decodes main feature
audio and BONUSVIEW
audio stream together
into PCM audio and
add Navigation Sound
Effects, then re-
encodes the PCM
audio into Dolby Digital
bitstream
* If Source Stream is 2ch, "Re-encoded Dolby D" Settings are not applied.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of the main feature.
- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
- Navigation Sound Effects : When you choose a menu navigation selection, a Navigation Sound
Effect may sound. Navigation Sound Effects are different on each Blu-ray Disc.
12
✎
NOTES
`
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
`
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
`
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
`
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
`
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
`
If your TV is not compatible with compressed
multi-channel formats (Dolby Digital, DTS), the
player may output PCM 2ch downmixed audio
even though you selected Bitstream (either Re-
encoded or Unprocessed) in the setup menu.
`
If your TV is not compatible with PCM sampling
rates over 48kHz, the player may output 48kHz
downsampled PCM audio even though you set
PCM Downsampling to Off.
PCM Downsampling
Lets you choose to have 96KHz PCM
signals downsampled to 48KHz before
they are outputted to an amplifier.
Choose On if your amplifier or receiver is
not compatible with a 96KHz signal.
Dynamic Range Control
Lets you apply dynamic range control
to Dolby Digital, Dolby Digital Plus, and
Dolby TrueHD audio.
•
Auto : Automatically controls the dynamic
range of Dolby TrueHD audio, based on
information in the Dolby TrueHD soundtrack.
Also turns dynamic range control on for
Dolby Digital and Dolby Digital Plus.
•
Off : Leaves the dynamic range
uncompressed, letting you hear the
original sound.
•
On : Turns dynamic range control on
for all three Dolby formats. Quieter
sounds are made louder and the
volume of loud sounds is reduced.
Downmixing Mode
Lets you select the multi-channel
downmix method that is compatible with
your stereo system. You can choose
to have the player downmix to normal
stereo or to surround compatible stereo.
Network Settings
To begin setting up the network connection
for your player, follow these steps:
1.
In the Home menu, press the
▲▼◄► buttons to select Settings,
and then press the
v
button.
2.
Press the ▲▼ buttons to select
Network, and then press the
v
button.
3.
Press the ▲▼ buttons to select
Network Settings, and then press
the
v
button.
4.
Press the ▲▼ buttons to select
Network Type, and then press the
v
button.
5.
Press the ▲▼ buttons to select
Wired or Wireless, and then press
the
v
button.
6.
Go to the next section.
Configuring Your Network
Connection
Before you begin, contact your ISP to find
out if your IP address is static or dynamic.
If it is dynamic, and you have a wired or
wireless network, we recommend using
the Automatic configuration procedures
described below.
If you are connecting to a wired network,
connect the player to your router
using a LAN cable before you start the
configuration procedure.
If you are connecting to a wireless
network, disconnect any wired network
connection before you begin.
To begin configuring your network
connection, follow these steps:
Wired Network
Ğ
Wired - Automatic
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wired in the Network
Settings screen, and then press the
v
button.
5.
Select Connect button, and then
press the
v
button. The product
detects the wired connection,
verifies the network connection and
then connects to the network.
Ğ
Wired - Manual
If you have a static IP address or the
Automatic procedure does not work,
you'll need to set the Network Settings
values manually.
Follow Steps 1 and 2 in Wired -
Automatic, and then follow these steps:
1.
Select Network Status. The player
searches for a network, and then
displays the connection failed message.
2.
On the bottom of the screen, select
IP Settings, and then press the
v
button.
The IP Settings screen appears.
3.
Select the IP Setting field, and then
press the
v
button.
4.
Select Enter manually in the IP
Setting field, and then press the
v
button.
5.
Select a value to enter (IP Address,
for example), and then press the
v
button.
Use the number keypad on your
remote control to enter the numbers
for the value. Use the ◄► buttons
on the remote control to move from
entry field to entry field within a value.
When done with one value, press the
v
button.
6.
Press the ▲ or ▼ button to move
to another value, and then enter the
numbers for that value following the
instructions in Step 5.
7.
Repeat Steps 5 and 6 until you have
filled in all values.
13
✎
NOTES
`
You can get the Network values from your
Internet provider.
8.
When finished entering all the values,
press the RETURN or EXIT buttons.
The player verifies the network
connection and then connects to
the network.
Wireless Network
You can setup a wireless network
connection in four ways:
- Wireless Automatic
- Wireless Manual
- WPS(PBC)
- WPS(PIN)
When you configure the wireless network
connection, any wireless network devices
currently connected through the player
or, if applicable, the player's current wired
connection, will be disconnected.
Ğ
Wireless - Automatic
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network
Settings screen, and then press the
v
button. The player searches
for and then displays a list of the
available networks.
m
Move
"
Select
'
Return
Network Settings
Select your network type.
Network type Wireless
Wireless network
Add Network
You can connect your Blu-ray
player to the internet. Please
select which wireless network
to use.
WPS(PBC) Search
5.
Select the desired network, and then
press the
v
button.
6.
On the Security screen, enter your
network's Security Code or Pass
Phrase.
Enter numbers directly using the
number buttons on your remote
control. Enter letters by selecting a
letter with an arrow button, and then
pressing
v
button.
7.
When done, select Done and then
press the
v
button. The player
verifies the network connection and
then connects to the network.
8.
When verification is complete, select
OK, and then press the
v
button.
✎
NOTES
`
You should be able to find the Security Code or
Pass Phrase on one of the set up screens you
used to set up your router or modem.
Ğ
Wireless - Manual
If you have a static IP address or the
Automatic procedure does not work,
you'll need to set the Network Settings
values manually.
1.
Follow the directions in Wireless -
Automatic through Step 5.
2.
The player searches for a network,
and then displays the connection
failed message.
3.
On the bottom of the screen, select
IP Settings, and then press the
v
button.
The IP Settings screen appears.
4.
Select the IP Setting field, and then
press the
v
button.
5.
Select Enter manually in the IP
Setting field, and then press the
v
button.
6.
Select a value to enter (IP Address,
for example), and then press
v
button. Use the number keypad
on your remote control to enter the
numbers for the value. Use the ◄►
buttons on the remote control to
move from entry field to entry field
within a value. When done with one
value, press the
v
button.
7.
Press the ▲ or ▼ button to move
to another value, and then enter the
numbers for that value following the
instructions in Step 6.
8.
Repeat Steps 6 and 7 until you have
filled in all values.
✎
NOTES
`
You can get the Network values from your
Internet provider.
9.
When finished, and then press the
RETURN or EXIT buttons. The
Security Screen appears.
10.
On the Security screen, enter your
network's Security Code or Pass
Phrase. Enter numbers directly using
the number buttons on your remote
control. Enter letters by selecting a
letter with the ▲▼◄► buttons, and
then pressing the
v
button.
11.
When finished, select Done at the
right of the screen, and then press
the
v
button.
The player verifies the network
connection and then connects to
the network.
12.
After the player verifies the network,
select OK, and then press the
v
button.
Ğ
WPS(PBC)
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network
Settings screen, and then press the
v
button.
5.
Press the ▲▼ button on your
remote, and then press the ◄►
button to select the WPS(PBC).
6.
Press the
v
button on your
remote. The "Press the PBC button"
message appears.
14
1.
Turn on the Wi-Fi direct device and
activate its Wi-Fi Direct function.
2.
In the Home screen, select Settings,
and then press the
v
button.
3.
Select Network, and then press the
v
button.
4.
Select Wi-Fi Direct, and then press
the
v
button.
The Wi-Fi Direct devices that you
can connect appear.
5.
You have three ways to complete
the Wi-Fi connection:
•
Through the Wi-Fi device.
•
Through the player using PBC.
•
Through the player using a PIN.
Each is covered below.
Through the Wi-Fi Device
1.
On the Wi-Fi device, follow the
procedure on the device for
connecting to another Wi-Fi Direct
device. See the device's user
manual for instructions.
2.
When you have completed the
procedure, you should see a pop-
up on your TV screen saying that
a device that supports Wi-Fi Direct
has requested to connect. Select
OK, and then press the
v
button
to accept.
3.
The Connecting pop-up appears,
followed by the Connected pop-
up. When it closes, you should see
the device listed on the Wi-Fi Direct
screen as connected.
Through the Player Using PBC
1.
Select the Wi-Fi Direct device you
want to connect to this player, and
then press the
v
button. The PBC/
PIN pop up appears.
2.
Select PBC, and then press the
v
button. The PBC pop-up appears.
3.
Press the PBC button on the Wi-Fi
Direct device within 2 minutes.
4.
The Connecting pop-up appears,
followed by the Connected pop-
up. When it closes, you should see
the device listed on the Wi-Fi Direct
screen as connected.
Through the Player Using a PIN
1.
Select the Wi-Fi Direct device you
want to connect to this player, and
then press the
v
button. The PBC/
PIN pop up appears.
2.
Select PIN, and then press the
v
button. The PIN pop-up appears.
3.
Note the PIN code in the pop-up,
and then enter it into the appropriate
field in the Wi-Fi Direct device you
want to connect.
4.
The Connecting pop-up appears,
followed by the Connected pop-
up. When it closes, you should see
the device listed on the Wi-Fi Direct
screen as connected.
7.
Press the WPS(PBC) button on
your router within two minutes. Your
player automatically acquires all the
network settings values it needs and
connects to your network.
The Network Status screen appears.
The player connects to the network
after the network connection is
verified.
Ğ
WPS(PIN)
Before you begin, open the router's
setup menu on your PC and access the
screen with the WPS PIN entry field.
1.
In the Home screen, select Settings,
and then press the
v
button.
2.
Select Network, and then press the
v
button.
3.
Select Network Settings, and then
press the
v
button.
4.
Select Wireless in the Network
Settings screen, and then press the
v
button.
The player searches for and then
displays a list of the available
networks.
5.
Select the desired network, and then
press the ► button.
6.
Select the WPS(PIN), and then
press the
v
button. The PIN pop-up
appears.
7.
Enter the PIN into the WPS PIN entry
field in the router's Set Up screen
and then save the the screen.
✎
NOTES
`
Contact the manufacturer of the router for
instructions explaining how to access the
route's Set Up screens or refer to the router's
user's manual.
`
For WPS connection, set your wireless router’s
security encryption to AES. Setting to WEP
security encryption does not support WPS
connection.
Network Test
Use this menu item to check whether
your network connection is working or
not.
Network Status
Use to check whether a connection to
a network and the Internet has been
established
.
Wi-Fi Direct
The Wi-Fi Direct function allows you
to connect Wi-Fi Direct devices to the
player and each other using a peer-to-
peer network, without a wireless router.
✎
NOTES
`
Some Wi-Fi Direct devices may not support the
DLNA function if connected via Wi-Fi Direct. If
this is the case, it is advisable to change the
network connection method between devices.
`
Bluetooth transmissions can interfere with the
Wi-Fi Direct signal. Before you use the Wi-
Fi Direct function, we strongly recommend
that you turn off the Bluetooth function of any
active mobile device.
15
✎
NOTES
`
The current wired or wireless network
connection will be disconnected when you use
the Wi-Fi Direct function.
`
Text files, such as files with a .TXT or .DOC
extension, will not display when you are using
the Wi-Fi Direct function.
Screen Mirroring
The Screen Mirroring function lets you
view the screen of your smart phone
or android tablet on the TV you have
connected to the Blu-ray player.
1.
In the Home menu, press the
▲▼◄► buttons to select Screen
Mirroring, and then press the
v
button. The Screen Mirroring pop-up
appears.
2.
Launch DLNA Cast on your device.
3.
On your device, find the name of the
Blu-ray player in the list of available
devices and then select it.
4.
The TV will display a PIN. Enter the
PIN into your device.
5.
The TV displays a connecting
message (for example, Connecting
to Android_92gb...) and then
displays the connected message.
6.
In a few moments, the screen of
your device appears on the TV
screen.
7.
To stop Screen Mirroring, press the
EXIT or RETURN button on the
remote control, or disable Screen
Mirroring function of your smart phone.
✎
NOTES
`
You can connect to a device that supports
DLNA Cast. Note that connecting to such a
device may not be fully supported depending
on the manufacturer. For further information
on mobile connection support, refer to the
manufacturer’s web site.
`
When you are using the Screen Mirroring
function, video stuttering or audio dropouts
may occur, depending on your environment.
`
Bluetooth transmissions can interfere with
the Screen Mirroring signal. Before using
the Screen Mirroring function, we strongly
recommend that you turn off the Bluetooth
function on your smart phone or smart device
(tablet, etc.).
Device Name
Device Name function allows you to
change player's name by selecting from
device name list.
BD-Live Internet Connection
Set to allow or prohibit an Internet
connection when you use the BD-LIVE
service.
•
Allow (All) : The Internet connection
is allowed for all BD-LIVE contents.
•
Allow (Valid Only) : The Internet
connection is allowed only for BD-
LIVE contents containing a valid
certificate.
•
Prohibit : No Internet connection is
allowed for any BD-LIVE content.
✎
NOTES
`
What is a valid certificate?
When the player uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the player.
`
The Internet connection may be restricted
while you are using BD-LIVE contents.
Using BD-LIVE™
Once the player is connected to the
network, you can enjoy various movie-
related service contents using a BD-LIVE
compliant disc.
1.
Attach a USB memory stick to
the USB jack on the front of the
player, and then check its remaining
memory. The memory device must
have at least 1GB of free space to
accommodate the BD-LIVE services.
2.
Insert a Blu-ray Disc that supports
BD-LIVE.
3.
Select an item from various BD-LIVE
service contents provided by the
disc manufacturer.
✎
NOTES
`
The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
The DLNA Function
DLNA lets you play music, video, and
photo files located in your PC on the
player.
To use DLNA with your player, you must
connect the player to your network. (See
pages 13~16).
To use DLNA with your PC, you must
install DLNA software on your PC.
System Settings
Setup
By using the Setup function, you can set
the language, Network Settings, etc.
For more information about the Setup
function, refer to the Setup section of
this user manual (See page 10).
Quick Start
You can turn on the power quickly by
decreasing the boot time.
✎
NOTES
`
If this function is set to On, Standby power
consumption will be increased
.
16
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that
offers linked operations with other
Samsung players that have the Anynet+
feature.
To operate this function, connect this
player to an Anynet+ Samsung TV with
an HDMI cable.
With Anynet+ on, you can operate this
player using a Samsung TV remote
control and start disc playback simply
by pressing the PLAY ( ) button on
the TV’s remote control.
For more information, please see the TV
user manual.
✎
NOTES
`
This function is not available if the HDMI cable
does not support CEC.
`
If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
`
Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
`
If you have Anynet+ turned on, when you
turn off the product, disconnect, and then
reconnect the power cable, the product turns
on automatically to re-establish the Anynet+
connection. After about 15 seconds, it turns off
again automatically.
`
Some Samsung TVs, when connected to this
product using the Anynet+ function will, when
you turn them on, display a warning popup
message saying no connection has been
found. Never-the-less, the Anynet+ connection
is properly established and available to use.
BD Data Management
Enables you to manage the downloaded
contents you accessed through a Blu-
ray disc that supports the BD-LIVE
service and stored on a flash drive.
You can check the device’s information
including the storage size, delete the
BD data, or change the Flash memory
device.
✎
NOTES
`
In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
`
Your player supports the FAT16, FAT32, and
NTFS file systems. We recommend you use
USB devices that support USB 2.0 protocol
with 4 MB/sec or faster read/write speed.
`
The Resume Play function may not work after
you format the storage device.
`
The total memory available to BD Data Management
may differ, depending on the conditions.
Language Settings
You can select the language you prefer
for the On-Screen menu, Disc menu,
Audio, and Subtitles.
✎
NOTES
`
The selected language will only appear if it is
supported on the disc.
Security Settings
When you access this function for the
first time, the PIN screen appears.
Enter the default PIN - 0000 - using the
number buttons. To change the PIN, use
the Change PIN function. Each time you
access the Security Settings hereafter,
you must enter that four digit PIN. If you
don’t change the PIN, continue using
the default PIN.
BD Parental Rating
Prevents playback of Blu-ray Discs
with specific age ratings unless the 4
digit PIN is entered.
DVD Parental Rating
This function works in conjunction with
DVDs that have been assigned an age
rating or numeric rating that indicates
the maturity level of the content. These
numbers help you control the types of
DVDs that your family can watch.
Select the rating level you want to set.
For example, if you select Level 6, discs
rated above 6 - Level 7 and 8 - will not play.
A larger number indicates more mature
content.
When the DVD Parental Rating function
is on, you must enter the 4 digit PIN to
play discs with restricted rating levels.
Change PIN
Change the 4-digit password used to
access security functions.
To change the PIN, follow these steps:
1.
Select Change PIN, and then press
the
v
button. The Enter old PIN
screen appears.
2.
Enter the old PIN. If you never changed
the PIN, enter the default PIN: 0000.
The Enter new PIN screen appears.
3.
Enter the new PIN in the Enter new
PIN fields.
4.
Re-enter the new PIN in the Confirm
new PIN fields. The "PIN is changed
successfully." message appears.
5.
Press the
v
button.
If you forget your password
1.
Remove any discs.
2.
Press and hold the
^
button on the
front panel for 5 seconds or more.
All settings will revert to the factory
settings.
✎
NOTES
`
When the factory default settings are restored,
all the user stored BD data will be deleted.
General Settings
Time Zone
Lets you specify the time zone that is
applicable to your area.
17
Support Settings
Software Upgrade
The Software Upgrade menu allows
you to upgrade the player’s software for
performance improvements or additional
services.
By Online
To upgrade By Online, follow these steps:
1.
In the player’s menu, go to Settings
> Support > Software Upgrade
2.
Select By Online, and then press
the
v
button. The Connecting to
Server message appears.
3.
A popup message will appear if an
update is available.
4.
If you select Yes, download process
started. (Never turn the player on or
off manually during an upgrade.)
5.
When the update is completed, the
player will restart automatically.
✎
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or back on manually
during the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during a software upgrade.
Auto Upgrade Notification
If you have connected the player to your
network, and then set Auto Upgrade
Notification on, the player automatically
notifies you when a new software
version is available for the player.
To set Auto Upgrade Notification on,
follow these steps:
1.
Select Auto Upgrade Notification,
and then press the
v
button.
2.
Use the ▲▼ buttons to select On,
and then press the
v
button.
If there is a new software version
available, the player notifies you with a
popup message.
1.
To upgrade the firmware, select Yes
in the Pop-up. The player turns off
automatically, then restarts, and
begins the download. (Never turn
the player on or off manually during
an upgrade.)
2.
The update progress popup
appears.
3.
When the update is completed, the
player will restart automatically.
✎
NOTES
`
The upgrade is complete when the player
turns off, and then turns on again by itself.
`
Never turn the player off or on manually during
the update process.
`
Samsung Electronics takes no legal
responsibility for player malfunction caused by
an unstable Internet connection or consumer
negligence during software upgrade.
Contact Samsung
Provides contact information for
assistance with your player.
Terms of Service Agreement
Lets you view the general disclaimer
regarding third party contents and
services.
Reset
Returns all settings to their factory
defaults except for the network
settings.
`
No disc should be in the product when you
upgrade the software By Online.
By USB
To upgrade by USB, follow these steps:
1.
Visit www.samsung.com/
bluraysupport.
2.
Download the latest USB software
upgrade zip archive to your computer.
3.
Unzip the zip archive to your
computer. You should have a single
RUF file with the same name as the
zip file.
4.
Copy the RUF file to a USB flash
drive.
5.
Make sure there is no disc in the
player, and then insert the USB flash
drive into the USB port of the player.
6.
In the player’s menu, go to Settings
> Support > Software Upgrade.
7.
Select By USB.
✎
NOTES
`
No disc should be in the product when you
upgrade the software using the USB Host jack.
`
When the software upgrade is done, check the
software details in the software Upgrade menu.
`
Do not turn off the player during the
software upgrade. It may cause the player to
malfunction.
`
Software upgrades using the USB Host jack
must be performed with a USB flash memory
stick only.
18
Media Play
Playing a Commercially
Recorded Disc
1.
Press the
8
button to open the
disc tray.
2.
Place a disc gently into the disc tray
with the disc's label facing up.
3.
Press the
8
button to close the disc
tray. Playback starts automatically.
Playing Files on a USB
Device
There are two methods you can use to
play or view multimedia files located on
a USB device through your player.
Method 1
1.
Turn the player on.
2.
Connect the USB device to the USB
port on the front panel of the player.
The New Device Connected pop-up
appears.
App 1 App 2 App 3 App 4 App 5
More
Screen Mirroring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS MUSIC
No Disc
New device connected.
Photos
Videos
Music
123
>
Move
"
Enter
'
Return
✎
NOTES
`
If the pop-up does not appear, go to Method 2.
3.
Use the ▲▼ buttons to select
Photos, Videos or Music, and then
press the
v
button. The Photos,
Videos & Music screen appears
listing the content of the device.
Depending on how the contents is
arranged, you will see either folders,
individual files, or both.
✎
NOTES
`
Even though the player will display folders
for all content types, it will only display files
of the Content Type you selected in Step
3. For example, if you selected music, you
will only be able to see music files. You can
change this selection by returning to the
Photos, Videos & Music screen and going to
Step 3 in Method 2 below.
4.
If necessary, use the ▲▼◄►
buttons to select a folder, and then
press the
v
button.
5.
Select a file to view or play, and then
press the
v
button.
6.
Press the RETURN button to exit a
folder or the EXIT button to return to
the Home screen.
7.
Go to pages 20~22 for instructions
that explain how to control playback
of videos, music, and pictures on a
USB device.
Method 2
1.
Turn the player on.
2.
Connect the USB device to the USB
port on the front panel of the player.
Select Change Device and then
press the ▲▼ button to select USB.
Press the
v
button.
App 1 App 2 App 3 App 4 App 5
More
Screen Mirroring
Change Device
Settings
PLAY DISC PHOTOS VIDEOS
MUSIC
No Disc
Change Device
No Disc
123
a
Close
3.
Use the ▲▼◄► buttons to select
PHOTOS, VIDEOS or MUSIC on the
Home screen, and then press the
v
button. The Photos, Videos & Music
screen appears listing the content of
the device. Depending on how the
contents is arranged, you will see
either folders, individual files, or both.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 3. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Photos, Videos &
Music screen and repeating Step 3.
4.
If necessary, use the ▲▼◄►
buttons to select a folder, and then
press the
v
button.
5.
Use the ▲▼◄► buttons to select
a file to view or play, and then press
the
v
button.
6.
Press the RETURN button to exit a
folder or the EXIT button to return to
Home screen.
7.
Go to pages 20~22 for instructions
that explain how to control playback
of videos, music, and pictures on a
USB device.
✎
NOTES
`
If you insert a disc when playing a USB
device, the device mode changes to "Disc"
automatically.
Playing a Disc with User
Recorded Content
You can play multimedia files you have
recorded on Blu-ray, DVD, or CD discs.
1.
Place a user recorded disc into the
disc tray with the disc’s label facing
up, and then close the tray.
2.
Use the ◄► buttons to select the
type of content you want to view or
play - VIDEOS, PHOTOS, or MUSIC
- and then press the
v
button.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 2. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 2.
19
3.
A screen appears listing the contents
of the disc. Depending on how the
contents are arranged, you will see
either folders, individual files, or both.
4.
If necessary, use the ▲▼◄►buttons
to select a folder, and then press the
v
button.
5.
Use the ◄►▲▼ buttons to select
a file to view or play, and then press
the
v
button.
6.
Press the RETURN button one or
more times to exit a current screen,
exit a folder, or to return to the Home
screen. Press the EXIT button to
return directly to the Home Screen.
7.
Go to pages 20~22 for instructions
that explain how to control playback of
videos, music, and pictures on a disc.
Using DLNA
DLNA Connection
PC Blu-ray Disc Player
Play back PC's
files
1.
Connect the Blu-ray Disc Player,
your PC, and/or your DLNA
compatible device to the same
wireless network.
2.
Follow the directions in the DLNA
software Installation/Instruction
manual to set up devices and files
for playing or viewing.
3.
Select Change Device on the
player's Home screen, and then
press the
v
button. In the list
of DLNA connected devices that
appears, select your PC or other
DLNA compatible device, and then
press the
v
button.
4.
Use the ◄► buttons to select the
type of content you want to view
or play - VIDEOS, PHOTOS, or
MUSIC - and then press the
v
button.
✎
NOTES
`
Even though the player will display folders for
all content types, it will only display files of
the Content Type you selected in Step 4. For
example, if you selected music, you will only
be able to see music files. You can change this
selection by returning to the Home screen and
repeating Step 4.
5.
A screen appears listing the
contents of the PC or DLNA device.
Depending on how the contents are
arranged, you will see either folders,
individual files, or both.
6.
If necessary, use the ▲▼◄►buttons
to select a folder, and then press the
v
button.
7.
Use the ◄►▲▼ buttons to select
a file to view or play, and then press
the
v
button.
8.
Press the RETURN button one or
more times to exit a current screen,
exit a folder, or to return to the Home
screen. Press the EXIT button to
return directly to the Home Screen.
9.
Go to pages 20~22 for instructions
that explain how to control playback
of videos, music, and pictures on a
disc.
Controlling Video Playback
You can control the playback of video
content located on a Blu-ray disc, DVD,
CD, USB device, or your computer.
Depending on the media, some of the
functions described in this manual may
not be available.
During Blu-ray or DVD disc playback,
the Full screen button does not operate.
Buttons on the Remote Control
used for Video Playback
SCREEN
VIEW A-B
FULLBONUS REPEAT REPEAT
1
2
Playback related buttons
The player does not play sound in
Search, Slow or Step mode.
•
To return to normal speed playback,
press the
6
button.
6
button
Starts playback.
5
button
Stops playback.
7
button
Pauses playback.
Fast Motion
Play
During playback, press the
3
or
4
button.
Each time you press the
3
or
4
button, the playback speed
will change.
Slow Motion
Play
In pause mode, press the
4
button.
Each time you press the
4
button, the playback speed will
change.
Step Motion
Play
In pause mode, press the
7
button.
Each time you press the
7
button, a new frame appears.
Skip Motion
Play
During playback, press the
1
or
2
button.
Each time you press the
1
or
2
button, the disc moves to the
previous or next chapter or file.
Using the disc menu, title menu,
popup menu, and title list
DISC MENU
button
During playback, press this
button to start the disc menu
function.
TITLE MENU
button
During playback, press this
button to start the title menu
function.
POPUP MENU
button
During playback, press this
button to start the popup menu
function.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
Samsung BD-J5900 Manuel utilisateur
- Catégorie
- Lecteurs Blu-Ray
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Samsung BD-J5900 User manual
Documents connexes
-
Samsung BD-J5700 Manuel utilisateur
-
Samsung BD-E5400 Manuel utilisateur
-
Samsung BD-F5700 Manuel utilisateur
-
Samsung BD-J4500 Manuel utilisateur
-
-
Samsung BD-J5900 Manuel utilisateur
-
-
Samsung BD-J5100 Guide de démarrage rapide