TEAC AD-850 Le manuel du propriétaire

D01308150A

ENGLISH

Z

AD-850

Cassette Deck/CD Player

OWNER’S MANUAL

MODE D’EMPLOI

MANUAL DEL USUARIO

FRANÇAIS

ESPAÑOL

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

<

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

B

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

CAUTION

o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE

THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE.

o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A

SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN

REPAIRED.

o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT

IN HAZARDOUS RADIATION EXPOSURE.

IN USA/CANADA, USE ONLY ON 120 V SUPPLY.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than

the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into your outlet,

consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

13) Unplug this apparatus during lightning storms or when unused

for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally,

or has been dropped.

o The apparatus draws nominal non-operating power from the

AC outlet with its POWER or STANDBY/ON switch not in the ON

position.

o The mains plug is used as the disconnect device; the disconnect

device shall remain readily operable.

o Caution should be taken when using earphones or headphones

with the product because excessive sound pressure (volume) from

earphones or headphones can cause hearing loss.

IMPORTANT SAFETY INSTRUCTIONS

3

ENGLISH

Laser information

This product contains a semiconductor laser system inside the cabinet

and is classified as a “CLASS 1 LASER PRODUCT”.

To prevent being exposed to the laser beam, do not try to open the

enclosure.

Laser:

Type: EP-C101

Manufacturer: GUANGDONG EVER BRIGHT GROUP CO.,LTD

Laser output: Less than 1 mW on the objective lens

Wavelength: 790 ±25 nm

Model for USA

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on the

Radiation Control for Health and Safety Act of 1968”, and is classified

as class ! laser product. There is not hazardous invisible laser radiation

during operation because invisible laser radiation emitted inside of

this product is completely confined in the protective housings.

The label required in this regulation is as follows:

For U.S.A.

CAUTION

o Do not expose this apparatus to drips or splashes.

o Do not place any objects filled with liquids, such as vases, on

the apparatus.

o Do not install this apparatus in a confined space such as a book

case or similar unit.

o The apparatus should be located close enough to the AC outlet

so that you can easily reach the power cord plug at any time.

o If the product uses batteries (including a battery pack or

installed batteries), they should not be exposed to sunshine, fire

or excessive heat.

o CAUTION for products that use replaceable lithium batteries:

there is danger of explosion if a battery is replaced with an

incorrect type of battery. Replace only with the same or equiva-

lent type.

V

Precautions concerning batteries

Misuse of batteries could cause them to rupture or leak leading to fire,

injury or the staining of nearby things. Please read and observe the

following precautions carefully.

o Be sure to insert the batteries with correct positive (¥) and nega-

tive (^) orientations.

o Use batteries of the same type. Never use different types of batter-

ies together.

o If the remote control is not used for a long time (more than a

month), remove the batteries to prevent them from leaking.

o If the batteries leak, wipe away the leakage inside the battery com-

partment and replace the batteries with new ones.

o Do not use batteries of types other than those specified. Do not

mix new batteries with old ones or use different types of batteries

together.

o Do not heat or disassemble batteries. Never throw batteries into

fire or water.

o Do not carry or store batteries with other metallic objects. The bat-

teries could short circuit, leak or explode.

o Never recharge a battery unless it is confirmed to be a recharge-

able type.

4

Supply of this product does not convey a license nor imply any right

to distribute MPEG Layer-3 compliant content created with this

product in revenue-generating broadcast systems (terrestrial, satellite,

cable and/or other distribution channels), streaming applications (via

Internet, intranets and/or other networks), other content distribution

systems (pay-audio or audio-on-demand applications and the

like) or on physical media (compact discs, digital versatile discs,

semiconductor chips, hard drives, memory cards and the like).

An independent license for such use is required. For details, please

visit http://mp3licensing.com.

MPEG Layer-3 audio coding technology is licensed from Fraunhofer IIS

and Thomson.

Other company names, product names and logos in this document

are the trademarks or registered trademarks of their respective owners.

For European Customers

Disposal of electrical and electronic equipment and

batteries and/or accumulators

a) All electrical/electronic equipment and waste batteries/accu-

mulators should be disposed of separately from the municipal

waste stream via collection facilities designated by the govern-

ment or local authorities.

b) By disposing of electrical/electronic equipment and waste

batteries/accumulators correctly, you will help save valuable

resources and prevent any potential negative effects on human

health and the environment.

c) Improper disposal of waste electrical/electronic equipment

and batteries/accumulators can have serious effects on the

environment and human health because of the presence of

hazardous substances in the equipment.

d) The Waste Electrical and Electronic Equipment (WEEE)

symbols, which show wheeled bins that have been

crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected

and disposed of separately from household waste.

If a battery or accumulator contains more than the

specified values of lead (Pb), mercury (Hg), and/or cad-

mium (Cd) as defined in the Battery Directive (2006/66/

EC), then the chemical symbols for those elements will

be indicated beneath the WEEE symbol.

e) Return and collection systems are available to end users. For

more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators,

please contact your city office, waste disposal service or the

shop where you purchased the equipment.

Pb, Hg, Cd

Model for USA

This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the equipment and/or the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Model for Canada

Industry Canada’s Compliance Statement:

This Class B digital apparatus complies with Canadian ICES-003.

Model for Europe

This product complies with the European

Directives request, and the other Commission

Regulations.

CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to oper-

ate the equipment.

IMPORTANT SAFETY INSTRUCTIONS (continued)

5

ENGLISH

Thank you for choosing this TEAC product. Read this manual

carefully to get the best performance from this unit.

Record on a USB flash drive from a

CD, a cassette tape or an external

source

e “Recording on a USB flash drive” on

page 28

Record on a cassette tape from a

CD, a USB flash drive or an external

source

e “Recording on a cassette tape” on

page 31

LINE IN

Recording

Requires a commercially-available timer

e “Timer-controlled playback and recording” on page 36

Timer-controlled playback

Timer-controlled recording

LINE IN

Timer operation

CD/CD-R/CD-RW

(Audio CD/MP3 disc)

e “Listening to a CD” on page 18

Cassette tape

e “Listening to a cassette tape” on

page 24

MP3 files on a USB flash drive

e “Listening to files on a USB flash

drive” on page 26

Playback

What you can do with this unitContents

IMPORTANT SAFETY INSTRUCTIONS ..............................2

What you can do with this unit ...................................5

Before use ........................................................6

Discs .............................................................7

Cassette tapes ....................................................8

USB flash drives ..................................................9

MP3 files ....................................................... 10

Identifying the parts (remote control) ........................... 10

Identifying the parts (main unit) .................................12

Using the remote control ........................................14

Display ..........................................................14

Connections ....................................................16

Basic operation ..................................................17

Listening to a CD ................................................18

Repeat playback ................................................ 20

Shuffle playback ................................................20

Programmed playback ......................................... 21

Listening to a cassette tape ..................................... 24

Listening to files on a USB flash drive ........................... 26

Recording on a USB flash drive .................................28

Erasing files from a USB flash drive ..............................30

Recording on a cassette tape ....................................31

Mic mixing with playback and recording ........................34

Timer-controlled playback and recording ....................... 36

Automatic power saving function ..............................38

Troubleshooting ................................................39

MP3 playback order ............................................40

Maintenance ...................................................40

Specifications ...................................................41

6

Before use

What’s in the box

Confirm that the standard accessories are included.

Remote control (RC-1329) × 1

Batteries (AAA) for remote control × 2

RCA audio cables × 2

Owner’s manual (this document) × 1

o For information about the warranty, users living in the USA

and Canada should see pages 124–125 and the back cover

(warranty document). Users living in Europe and other regions

should see page 126.

o Keep this manual in a safe place for future reference.

Quick start guide for recording × 1

Precautions for use

< Do not move the unit during CD playback.

During CD playback, the disc rotates at high speed. Do not lift or

move the unit during playback. Doing so might damage the disc

or the unit.

< The voltage supplied to the unit should match the voltage that

is printed on the rear panel. If you are in any doubt regarding this

matter, consult an electrician.

< Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into the

unit, contact your dealer or service company.

< When removing the power plug from the wall outlet, always pull

directly on the plug, never yank on the cord.

< Always remove the disc before relocating or moving this unit.

Moving the unit with a disc inside it could cause malfunction.

Placement of the unit

< Choose the location where you install the unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. You should

also avoid locations that are subject to vibrations or exposed to

excessive dust, heat, cold or moisture.

< As the unit may become warm during operation, always leave

sufficient space around it for ventilation.

< Do not place the unit on an amplifier, a receiver or any other

device that generates heat.

Beware of condensation

When the unit is moved from a cold to a warm place, or used after a

sudden temperature change, there is a danger of condensation; vapor

in the air could condense on the internal mechanism, making correct

operation impossible. To prevent this, or if this occurs, leave the unit

turned on for one or two hours. Then the unit will stabilize at the tem-

perature of its surroundings.

Using the TEAC Global Site

You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site.

2) In the TEAC Downloads section, click the desired language to

open the Downloads website page for that language.

NOTE

If the desired language does not appear, click Other Languages.

3) Click the “Search by Model Name” section to open the Downloads

page for that product. (Users in Europe should click the product

name in the “Products” section instead.)

4) Select and download the updates that are needed.

Product registration

Customers in the USA, please visit the following TEAC website to regis-

ter your TEAC product online.

http://audio.teac.com/support/registration/

7

ENGLISH

Discs

Discs that can be played by this unit

This unit can play these types of discs without an adapter. It cannot

play any other type of disc.

Playback of any other type of disc could cause loud noise and

damage to speakers as well as harm hearing. Never try to play

any other type of disc.

< Depending on the quality of the disc and/or the condition of the

recording, some discs might not be playable.

< Video CDs, CD-ROMs and similar types of discs can be read by the

unit, but they will make no sound when played back.

< Super Audio CDs cannot be read or played back by this unit.

< Video and audio DVDs, DVD-ROMs and other types of DVDs

cannot be read or played back by this unit.

ATTENTION

If you put a video or audio DVD, DVD-ROM or other type of DVD

into the disc tray, the unit will attempt to read the disc and rotate

at high speed. If you accidentally insert such a disc, wait until the

unit stops spinning before ejecting it in order to avoid possibly

damaging the disc. Do not attempt to remove the disc when

“READING” appears on the display.

< Copy-protected discs and other discs that do not conform to the

CD standard might not play correctly in this player. If you use such

discs in this unit, TEAC Corporation and its subsidiaries will not

be responsible for any consequences or guarantee the quality of

reproduction. If you experience problems with such non-standard

discs, you should contact their issuers.

About CD-R/CD-RW discs

This unit can play back CD-R and CD-RW discs that have been

recorded in the audio CD format (CD-DA) and the MP3 format.

< Discs created by a CD recorder must be finalized before use with

this unit.

< Depending on disc quality and recording conditions, playback of

some discs might not be possible. Please see the manual for the

device that you used to create the disc.

< If you are uncertain about the handling of a CD-R or CD-RW disc,

please contact the seller of the disc directly.

CDs (12-cm and 8-cm) that bear the “COMPACT disc DIGITAL

AUDIO” logo can be played by this unit.

< The logo should be on the disc label or the CD jacket.

CD-R and CD-RW discs that have been correctly recorded in

the audio CD format and finalized, as well as finalized CD-R and

CD-RW discs that contain MP3 files, can be played by this unit.

Precautions for use

< Do not play any disc that is warped, deformed or damaged.

Playing such discs could cause irreparable harm to the playing

mechanisms.

< Printable CD-R and CD-RW discs are not recommended because

their label sides could be sticky and damage the unit.

< Do not stick paper or protective sheets on discs and do not use

any protective coating sprays.

< Never use a stabilizer. Using commercially-available CD stabilizers

with this unit will damage the mechanisms and cause them to

malfunction.

< Do not use irregularly-shaped discs (octagonal, heart-shaped,

business card size, etc.). Such CDs could damage the unit.

Handling precautions

< Always place the disc on the disc tray with the label side up. Only

one side of a Compact Disc can be played or used for recording.

< To remove a disc from a standard storage case, press down on the

case through the center of the disc and lift the disc out, holding it

carefully by its edges.

How to remove a disc How to hold a disc

Storage precautions

< Discs should be returned to their cases after use to avoid dust and

scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high temperature

or humidity for extended periods. Long exposure to high

temperatures will warp discs.

< CD-R and CD-RW discs are more sensitive to the effects of heat

and ultraviolet rays than ordinary CDs. It is important that they

not be stored in locations where they will be exposed to direct

sunlight. They should also be kept away from sources of heat, such

as radiators and heat-generating electrical devices.

8

Discs (continued)

Maintenance

< If a disc becomes dirty, wipe its surface radially from the center

hole outward towards the outer edge with a soft, dry cloth.

< Never clean discs using chemicals such as record sprays, antistatic

sprays and fluids and thinners. Such chemicals will do irreparable

damage to the disc’s plastic surface.

If you are in any doubt as to the care and handling of a CD-R or

CD-RW disc, read the precautions supplied with the disc or contact

the disc manufacturer.

Cassette tapes

Tape types

There are several types of cassette tapes.

Cassette tapes that can be played by this unit

Cassette tapes that can be recorded on by this unit

ATTENTION

< Do not open a cassette or pull out the tape.

< Do not touch the tape.

Storage precautions

< Keep cassette tapes away from magnets or magnetized items

because they may cause noise or erase recorded contents.

< Do not leave cassette tapes in a dusty place.

< Do not store cassette tapes in a place with high temperature or

humidity.

Types of cassette tapes that should be avoided

The following types of cassette tapes might prevent the unit from

operating or functioning normally. The tape of such cassette tapes

could be caught in the unit and cause unexpected problems.

Deformed cassette tapes

Cassettes that are deformed, that have tape that does not track

properly, or that generate abnormal noise during fast-forwarding

or rewinding.

Long-duration tapes

Tapes that allow recording for longer than 90minutes sometimes

get caught by the capstan because they are extremely thin and

stretch easily. Do not use them.

Slackening of tapes

Slack tape could get caught in the capstan or other parts.

Eliminate slack by using a pencil or similar tool before use.

Normal (type ) Chrome (type ) Metal (type )

Normal (type ) Chrome (type )

9

ENGLISH

USB flash drives

ATTENTION

Never turn the unit off or disconnect a USB flash drive when

it is being accessed, for example, during writing, playback,

recording or the erasure of files.

Doing so could damage the unit and the connected USB flash

drive.

Compatibility

o Only USB flash drive can be used.

o Hard disk drives, CD/DVD drives, and other devices connected via

USB cannot be used.

o This unit cannot copy or move files.

o Playable formats: FAT12, FAT16, FAT32

o NTFS, HFS and HFS+ formats cannot be used.

o Max. number of playable folders: 255

o Max. number of playable/recordable files: 999

o Operation with all USB flash drives is not guaranteed.

o When recording from a CD to a USB flash drive, the monitored

sound might skip depending on the type of USB flash drive, but

this will not affect the recorded data.

Recording

This unit can record sound from CDs, cassette tapes and connected

external devices, including tuners, to USB flash drives in MP3 format.

See page 28 for details.

Automatic tape type detection function

This cassette deck can detect what type of tape is being used based

on the detection holes in the cassette shell. Be sure to use cassettes

with detection holes.

Metal

(

Type

)

Chrome

(

Type

)

Normal

(

Type

)

Automatic tape type

detection holes

Accidental erasure prevention tabs

Tabs in the top of the cassette shell allow you to prevent important

recordings from being erased by mistake. There are two tabs in each

cassette shell—one for “side A” and one for “side B.”

Once these tabs have been removed using a screwdriver or similar

tool, there is no chance of the recording function being activated by

accident.

Accidental erasure prevention

tab

for “side A”

“side A”

o To record on a cassette that has had its tab broken off, put a piece

of adhesive tape over the hole. Be careful not to block the tape

type detection holes.

10

Identifying the parts (remote control)

A

B

E

D

F

G

K

C

H

I

J

If both the main unit and the remote control have buttons with

the same function, we only explain procedures using one of them

in this manual. However, the other can also be used in the same

manner.

MP3 files

This unit can play MP3 files that are on CD-R/CD-RW discs and

external USB flash drives.

o Playable audio file formats

MP3 (with “.mp3” extension)

8–320kbps bit rate

16–48kHz sampling frequency

NOTE

DRM (Digital Rights Management) is not supported.

o Up to eight levels of subfolders are supported.

File information display

The display of this unit can only show single-byte letters and

numbers.

< If the file information uses Japanese, Chinese or other double-byte

characters, playback is possible but the name will not be shown

correctly. In such cases, “

” is displayed.

Precautions when preparing MP3 files using a computer or

other device

o Discs that have not been recorded in accordance with ISO 9660

specifications cannot be played back.

o MP3 files are recognized by the “.mp3” extension. Always include an

extension at the end of the file name.

o Files without extensions cannot be recognized. Files that are not in

the MP3 data format cannot be played back even if they have an

extension.

o After writing to a CD-R/CD-RW, close the session (complete disc

creation). If the session has not been closed, the disc cannot be

played back.

o This unit can play a maximum of 999 files in a maximum of 255

folders. If data exceed these numbers, proper playback might not

be possible for files numbered 1000 or higher and files in folders

numbered 256 or higher.

o Discs recorded using multiple sessions are not supported. Only the

first session will be played back.

o Depending on the disc condition, this unit might not be able to

play some discs or skipping could occur.

o Files protected by DRM cannot be played back by this unit.

11

ENGLISH

A

SOURCE button

Use this button to select a source (page 17).

B

DISPLAY button

Press this button to change the display information (page 15).

C

REPEAT button

Use this button to set the repeat function (page 20).

D

SHUFFLE button

Use this button to start shuffle playback (page 20).

E

PROGRAM button

Use this button to program tracks/files (page 21).

F

CLEAR button

Use this button to clear programmed tracks/files (page 23).

G

FOLDER ( / ) buttons

Use these buttons to select MP3 folders (pages19 and 27).

H

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through tracks/files.

Hold down these buttons to search for part of a track/file.

OPEN/CLOSE (L) button

Press this button to open and close the disc tray.

Stop (H) button

Press this button to stop playback.

Play (

t

) button

Press this button to start playback.

Pause (J) button

Press this button to pause playback. To resume playback, press

this button again.

I

ERASE button

Use this button to erase files from a USB flash drive (page 30).

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through files.

Hold down these buttons to search for a part of a file.

RECORD (>) button

Use this to record to an external USB flash drive. Press it once to

enable recording standby, and press it again to start recording.

(page 28)

Press it during recording to divide the file at that point (page

30).

Stop (H) button

This stops USB flash drive recording/playback.

Play (

t

) button

Press this button to start playback.

When in USB recording standby, press this to start recording.

Pause (J) button

Press this button to pause playback or recording.

Press this button again to resume playback or recording.

J

Stop (H) button

Press this button to stop playback.

Press this button to stop recording to a tape.

Play (

t

) button

This starts cassette tape playback.

Press when a cassette tape is paused to resume playback/

recording.

Pause (J) button

Press this button to pause playback or recording.

Press this button again to resume playback or recording.

ATTENTION

When stopped, pressing the Pause (9) button will not put the

tape into a paused state.

Fast-forward/Rewind (m/,) buttons

Press these buttons to fast-forward/rewind the tape.

RECORD (>) button

Use to record to a tape. Press it once to enable recording standby,

and press it again to start recording (page 31).

COUNTER RESET button

Press this button to reset the tape counter to “0000”.

K

REC LEVEL ( − / + ) buttons

Use these buttons to adjust the recording level.

12

1

Display

This shows the total number of tracks/files, playback time and

other information (page 14).

2

Remote sensor

When operating the remote control, point it towards here.

3

OPEN/CLOSE (L) button

Press this button to open and close the disc tray.

4

COUNTER RESET button

Press this button to reset the tape counter to “0000”.

5

REC LEVEL knob

Turn this knob to adjust the recording level.

6

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through tracks/files.

Hold down these buttons to search for part of a track/file.

7

REPEAT button

Use this button to set the repeat function (page 20).

8

SOURCE button

Use this button to select the source (page 17).

9

Stop (H) button

Press this button to stop cassette tape playback.

Press this button to stop recording to a tape.

10

RECORD USB button

Use to record to an external USB flash drive. Press it once to

enable recording standby, and press it again to start recording

(page 28).

Press it during recording to divide the file at that point (page

30).

11

RECORD TAPE button

Use to record to a tape. Press it once to enable recording standby,

and press it again to start recording (page 31).

12

Fast-forward/Rewind (m/,) buttons

Press these buttons to fast-forward/rewind the cassette tape.

13

Pause (J) button

Press this button to pause cassette tape playback or recording.

Press this button again to resume playback or recording.

14

Cassette tape compartment

15

MIC connector and mic LEVEL knob

When using a mic to record, insert the mic cable plug into this

connector and turn the knob to a suitable level (page 34).

This unit does not support stereo mics.

Use a mono dynamic mic.

Set the MIC LEVEL knob to MIN when not using a mic.

Identifying the parts (main unit)

1

43 5

8

6 7

1110

12

132

1819

17

24

9

2831 30 29 27 25 23 2132 26 22 20

13

ENGLISH

16

EJECT (L) button

When the tape is stopped, press this button to open the cassette

tape compartment.

17

Play (

t

) button

This starts cassette tape playback.

Press when a cassette tape is paused to resume playback/

recording.

18

PITCH CONTROL knob

Turn this knob to vary the playback speed (page 25).

19

ECHO MODE switch

This changes the echo mode (page 35).

20

Pause (J) button

Press this button to pause CD playback. To resume playback,

press this button again.

21

FOLDER ( / ) buttons

Use these buttons to select folders (pages19 and 27).

22

POWER ON START OFF-PLAY-REC (TAPE) switch

Use this switch to set the timer operation mode (off, play or record).

To use this when set to play or record, connect a commercially-

available programmable timer to this unit (page 36).

o Select OFF to not use timer playback or recording.

23

Play (

t

) button

Press this button to start CD playback.

24

Stop (H) button

Press this button to stop CD playback.

25

Skip (.//)/Search (m/,) buttons

Press these buttons to skip through files.

Hold down these buttons to search for part of a file.

26

POWER ON START CD-TAPE-USB switch

Use this switch to set the sound source that is active when the

power is turned on.

Use this switch to set the media used for timer playback/

recording. (The timer recording can only record to cassette tape.)

To use timer playback/recording, connect a commercially-

available programmable timer to this unit (page 36).

27

Pause (J) button

Press this button to pause USB playback or recording.

Press this button again to resume playback or recording.

28

Play (

t

) button

Press this button to start USB playback.

When in USB recording standby, press this to start recording.

29

Stop (H) button

Press this button to stop USB playback.

Press this button also to stop recording to USB.

30

Disc tray

31

USB port

Connect an external USB flash drive here.

32

POWER button

Press this button to turn the unit on or off.

ATTENTION

Never turn the unit off or disconnect a USB flash drive

when it is being accessed, for example, during writing,

playback, recording or the erasure of files.

Doing so could damage the unit and the connected USB

flash drive.

16

15

14

Display

CD mode

During playback

Audio CD

Currently playing track number

Elapsed time of current track (min./sec.)

MP3 disc

Elapsed time of current track

(min./sec.)

Currently playing folder number

Currently playing file number

(starting with 001 in each folder)

Currently playing file name

(scrolls when long)

When playback is stopped

Audio CD

Total tracks

Total playing time

MP3 disc

Total number of folders

Total number of files

Using the remote control

Precautions when using the remote control

V

CAUTION

Misuse of batteries could cause them to rupture or leak, which

might result in fire, injury or the staining of nearby materials.

Please read and observe the precautions on page 3 carefully.

o When using the remote control, point it toward the remote control

signal receiver on the main unit from a distance of 5 m (16 ft) or

less. Do not place obstructions between the main unit and the

remote control.

< Even if the remote control is used within its effective range,

operation by remote control might not be possible if there are any

obstacles between the unit and the remote control.

< If the remote control is operated near other devices that generate

infrared rays, or if other remote controls that use infrared rays are

operated near the unit, this unit and the other devices might not

operate correctly.

Battery installation

1. Remove the battery compartment cover.

2. Insert two AAA batteries. Make sure that they are inserted with

their positive (+) and negative (_) poles oriented correctly.

3. Close the cover.

Battery replacement

If the distance from the main unit that the remote control works

effectively decreases, the batteries are probably exhausted. Replace

the batteries with new ones when this happens.

For more information about the collection of batteries, please contact

your local municipality, your waste disposal service or the place where

you purchased them.

15

ENGLISH

TAPE mode

Tape counter

o The tape counter shows the approximate position of the tape. This

is not a time indication.

USB mode

During playback

Elapsed time of current file

(min./sec.)

Currently playing folder number

Currently playing file number

(starting with 001 in each folder)

Currently playing file name

(scrolls when long)

When playback is stopped

Total number of folders

Total number of files

Recording mode

(Example: Recording on a cassette tape from a USB flash drive)

Tape counterElapsed time of

current file (min./sec.)

Current file

number

Recording source Recording indicator

Changing the display (CD/USB mode)

During playback in CD mode or USB mode, each time the DISPLAY

button is pressed, the display changes as follows:

Audio CD

Remaining time of current track (min./sec.)

Total elapsed time of the disc (min./sec.)

Total remaining time of the disc (min./sec.)

Currently playing track number

and elapsed time of current track (min./sec.)

MP3 disc/USB

File name

Title

Artist

Album

Currently playing folder and file number,

elapsed time of current track (min./sec.),

and currently playing file name

< “No title”, “No album” or “No artist” appears when there is no

information.

< “

” appears when the unit cannot read the information.

< The display of this unit can only show single-byte letters and

numbers. If a file name uses Japanese, Chinese or other double-

byte characters, playback is possible but the name will not be

shown correctly. In such cases, “

” is displayed.

16

A

LINE IN/OUT connectors

These connectors transmit an analog 2-channel audio signal.

Connect the components using the included RCA audio cables.

Connect a stereo amplifier, mixer or other equipment to this

unit’s analog audio input and output connectors.

Use the included RCA audio cables (or commercially-available

ones) for connections.

Connect this unit’s R input connector to the R output connector

of the audio output device, and this unit’s L input connector to

the L output connector of the other device.

White (L)

Red (R)

White (L)

Red (R)

This unit Amplifier, etc.

B

AC Power Cord

After all other connections are complete, connect the plug to an

AC wall outlet.

Be sure to connect the power cord to an AC outlet that

supplies the correct voltage.

Hold the power plug when plugging it into an outlet or

unplugging it. Never pull or yank on the power cord.

Connections

V

Complete all other connections before turning the unit

on.

o Read the instructions of each device that you intend to use with

this unit.

o Be sure to connect each plug securely. Do not bundle connecting

cables with power cords. Doing so could cause noise.

LINE

IN

LINE

OUT

AD-850 (back side)

Amplifier

Tuner, etc.

Speakers

RCA audio cables

Wall socket

Example

Notes on turning on or off the power

When an amplifier is connected to the unit, turn on or off the power

of the unit and the amplifier in the following sequence.

When turning on the power

1. This unit

2. Amplifier

When turning off the power

1. Amplifier

2. This unit

17

ENGLISH

Basic operation

Turning the unit on or off

Press the POWER button to turn the unit on or off.

When the unit turns on, the display lights.

Check the POWER ON START switches that determine what the

unit does when the power is turned on.

When the power is turned on, and the POWER ON START

OFF-PLAY-REC (TAPE) switch for the timer is set to PLAY

or REC

or

The source set with the POWER ON START CD-TAPE-USB

switch starts playback/recording.

The timer recording can only record to cassette tape (page

37).

When the power is turned on, and the POWER ON START

OFF-PLAY-REC (TAPE) switch for the timer is set to OFF

The source set with the POWER ON START CD-TAPE-USB

switch becomes the active source.

< When you do not want to use the timer, be sure to set the

POWER ON START OFF-PLAY-REC (TAPE) switch to the OFF

position to prevent accidentally recording over an important

cassette tape.

Selecting a source for playback/recording

Each time the SOURCE button is pressed, the source changes as

follows:

The selected source is shown on upper left of the display.

< During recording, the source cannot be changed.

< Pressing the play button for a source also selects and starts

playback of that source.

< Select “LINE” to use an external source connected to the LINE

connectors.

18

1

Press the SOURCE button repeatedly to select “CD”.

< When a different source is selected, pressing the CD Play (t)

button automatically selects the CD and, if a disc is loaded, starts

playback.

2

Press the CD OPEN/CLOSE (L) button to open the disc

tray.

3

Place a disc on the tray with the label side up.

< Always confirm that the disc is centered on the tray. The disc

must be centred on the disc tray. If a disc is not correctly loaded,

it might not be possible to open the tray again after it has been

closed.

ATTENTION

< Do not load more than one disc.

< Do not force the tray by hand when opening and closing it.

< Do not attach adhesive labels or similar materials to either side

of a disc.

< Do not use irregularly-shaped discs.

Failure to follow any of the above could cause malfunction.

4

Press the CD OPEN/CLOSE (

L

) button again to close the

tray.

CAUTION

Be careful not to let your finger be pinched by the tray.

Loading a disc takes a few seconds.

During loading, “READING” appears on the display and no buttons

will work. Wait until the total number of tracks/files is displayed.

< When no disc is loaded, “NO DISC” is displayed.

5

Press the CD Play (

t

) button to start playback.

Playback starts from the first track/file on the disc.

< If you load a disc, and then press the CD Play (

t

) button

without having first closed the disc tray, the disc tray closes and

playback starts.

< When playback of all the tracks/files has finished, the unit stops

automatically.

< MP3 files that are not placed in folders are automatically put in

the “ROOT” folder. Playback starts from the first file in the ROOT

folder.

< See page 40 for information about the playback order of MP3

discs.

Listening to a CD

19

ENGLISH

Suspending playback temporarily

(Pause mode)

Press the CD Pause (J) button during playback to stop playback at

the current position.

To resume playback, press the CD Pause (J) button again or press

the CD Play (t) button.

Stopping playback

Press the CD Stop (H) button to stop playback.

Opening the disc tray

Press the CD OPEN/CLOSE (L) button to open the disc tray.

< You can also open the tray when in modes other than CD mode.

Search for a part of a track/file

Press and hold

During playback, hold down a CD Search (m or ,) button to

search a part of a track/file. Release it when you find the beginning

of the part you want to hear.

Skipping to an earlier or later track/file

During playback

Press a CD Skip (.//) button repeatedly until the desired

track/file is selected. The selected track/file will be played from the

beginning.

o If the . button is pressed once during playback, the track/

file being played will be played again from its beginning. To

return to the beginning of the previous track/file, press the .

button twice.

When playback is stopped or paused

Press a CD Skip (.//) button repeatedly to select the track/

file you want to hear. Then, press the CD Play (t) button or CD

Pause (J) button to start playback of the selected track/file.

Selecting a folder (MP3 disc)

Press the FOLDER ( / ) buttons to select a folder. Then, press

the CD Play (t) button to start playback.

20

This function can be used in CD and USB modes.

Press the REPEAT button to cycle through the following playback

modes:

Audio CD

REPEAT 1 REPEAT ALL

(oﬀ)

MP3

REPEAT 1 REPEAT ALL

(oﬀ)

REPEAT FOLDER

< If any of the following buttons are pressed, the repeat mode will

be canceled.

In CD mode

POWER button, SOURCE button, CD OPEN/CLOSE (L)

button, REPEAT button, SHUFFLE button

In USB mode

POWER button, SOURCE button, REPEAT button, SHUFFLE

button

REPEAT 1 (Repeat one track/file)

The track/file being played will be played repeatedly.

“REPEAT 1” appears on the display.

< If you use the CD/USB Skip (. or /) buttons to select a

different track/file, that track/file will be played repeatedly.

< You can select a track/file to be repeated when playback is

stopped. Press the REPEAT button, select a track/file using the CD/

USB Skip (. or /) buttons, and then press the CD/USB Play

(t) button or CD/USB Pause (J) button to start playback.

REPEAT ALL (Repeat all tracks/files)

All the tracks/files on the disc will be played repeatedly.

“REPEAT ALL” appears on the display.

< During program playback, the programmed tracks/files will be

played repeatedly.

REPEAT FOLDER (Repeat all the files in a folder) (MP3 only)

All the files in the selected folder will be played repeatedly.

“REPEAT FOLDER” appears on the display.

Repeat playback

Shuffle playback

This function can be used in CD and USB modes.

Use this function to play the tracks/files on a disc/USB flash drive in

random order.

Pressing the SHUFFLE button turns the shuffle mode on and off.

During shuffle playback, “SHUFFLE” appears on the display.

After playing back all tracks/files, the unit exits the “Shuffle”

playback mode and stops playback.

To stop shuffle playback, press the CD/USB Stop (H) button.

< If you press the / button during shuffle playback, the next

track/file will be randomly selected and played. If you press the

. button, the currently played track/file will be played from the

beginning. During shuffle playback, a track/file that has completed

playback will not be played again.

< The shuffle function does not work during program playback.

< If any of the following buttons are pressed, shuffle mode will be

canceled.

In CD mode

POWER button, SOURCE button, CD OPEN/CLOSE (L)

button, REPEAT button, SHUFFLE button

In USB mode

POWER button, SOURCE button, REPEAT button, SHUFFLE

button

La page est en cours de chargement...

TEAC AD-850 Le manuel du propriétaire

TEAC AD-850 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents