MPG155
&
MPG166
MALONE
R
3
Installation & Loading Instructions - Please Read Before Beginning
1
. Place the kayak onto the Blocks so that it
is aligned and the weight of the kayak is
evenly distributed on each Block.
See image 2.
. Unroll the Load Straps. Open the vehicle’s doors.
Throw the non-buckle ends of the Straps up and
over the kayak and down to the other side of the
vehicle. Center the Straps with the foam blocks.
See image 3.
12’ Bow & Stern Lines
15’ Load Straps
2
Kayak Blocks
MPG166
Step 1: Positioning Blocks & Loading Kayak
. Confirm that the Blocks and roof of the vehicle
are clean and free of dust and dirt. Do not place
Blocks on a sun roof.
For installation without cross bars; center the
Blocks on the vehicle’s roof. Maintain a minimum
of 24” between the Blocks. See image 1.
For installation with cross bars; fit the Blocks
onto the cross bars with the bottom profile of
each block fully inserted over each bar.
ROOF TOP TRANSPORT KIT
K
ARRIERAYAK
C
M
M
A
A
L
L
O
O
N
N
E
E
R
MALONE
R
DownLoaderDownLoaderTM
J-STYLE FOLDING KAYAK CARRIER
12’ Safety LinesJawz Universal Adapters Mounting BoltsKayak Carriers Load Straps T-Knobs
60mm
70mm
Installation & Loading Instructions - Please Read Before Beginning
Veuillez lire les instructions avant d’entreprendre l’installation et le chargement
1
3
2
. Insert Mounting Bolt through one hole of a Jawz adapter.
Insert washer and loosely apply a T-knob. See image 2.
. Faites passer le boulon de fixation dans l’un des trous
d’un adaptateur Jawz puis vissez légèrement un bouton
en ‘‘T’’ à la base du boulon. (Figure 2)
. Prior to installation, insert a bolt into the mounting holes in
the bottom of the carriers. Push upward to open the two
mounting hole covers located in the Base pads.
. Insert a Mounting Bolt into one mounting hole from the top
side. Rotate and close the mounting hole cover.
See image 1.
. Insérez un boulon de fixation dans l’un des trous hexagonaux
situés sur le côté supérieur du support.
(Figure 1)
. Place the carrier onto the front cross bar with the boarding
ramp facing out. Swing the Jawz under the cross bar as
shown. See image 3.
. Placez le support sur la barre transversale avant, la rampe
de chargement vers l’extérieur. Faites passer l’adaptateur
Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)
1
Mounting Bolt Washers
Base Pad
Covers
IMPORTANT WARNING: All vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for
following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind including death,
which may result from their use and/or installation.
It is critical that all Malone racks and accessories be properly and securely attached to your vehicle. Improper attachment could result in a serious
accident, and could cause serious bodily injury or death to you or to others. You are responsible for securing the racks and accessories to your car,
checking the attachment’s prior to use, and periodically inspecting the products for adjustment, wear, and damage.
You must read and understand all of the instructions and cautions supplied with your Malone products(s) prior to installation or use. If you do not
understand all of the instructions and cautions, or, if you have no mechanical experience and are not thoroughly familiar with the installation
procedures, you should have the product installed by a professional installer.
MISE EN GARDE IMPORTANTE: Tout transport d’un chargement sur le toit d’un véhicule est potentiellement dangereux. Une personne qui
utilise les produits Malone doit suivre sans faute les instructions d’installation et d’utilisation fournies et assume l’entière responsabilité pour tout
dommage ou toute blessure, y compris un décès, pouvant résulter d’une telle installation ou utilisation.
Il est essentiel de xer correctement et solidement les supports et les accessoires à votre véhicule. Une mauvaise installation ou attache pourrait
provoquer un accident, entraîner des blessures corporelles graves à vous et aux autres et même causer la mort. Vous avez la responsabilité de
xer solidement les supports et les accessoires à votre véhicule, de vérier l’installation avant l’utilisation et d’inspecter périodiquement le produit
pour déceler tout signe d’usure ou de dommage ou tout problème d’ajustement.
Vous devez lire et comprendre les instructions et les mises en garde fournies avec les produits Malone avant l’installation et l’utilisation. Si vous
ne comprenez pas les instructions et les mises en garde ou si vous ne possédez pas d’expérience en mécanique et ne connaissez pas à fond les
procédures à suivre d’installation, vous devriez faire monter et poser le produit par un installateur professionnel.
Combined Instructions
MALONE
R
3
Installation & Loading Instructions - Please Read Before Beginning
1
. Place the kayak onto the Blocks so that it
is aligned and the weight of the kayak is
evenly distributed on each Block.
See image 2.
. Unroll the Load Straps. Open the vehicle’s doors.
Throw the non-buckle ends of the Straps up and
over the kayak and down to the other side of the
vehicle. Center the Straps with the foam blocks.
See image 3.
12’ Bow & Stern Lines
15’ Load Straps
2
Kayak Blocks
MPG166
Step 1: Positioning Blocks & Loading Kayak
. Confirm that the Blocks and roof of the vehicle
are clean and free of dust and dirt. Do not place
Blocks on a sun roof.
For installation without cross bars; center the
Blocks on the vehicle’s roof. Maintain a minimum
of 24” between the Blocks. See image 1.
For installation with cross bars; fit the Blocks
onto the cross bars with the bottom profile of
each block fully inserted over each bar.
ROOF TOP TRANSPORT KIT
K
ARRIERAYAK
C
M
M
A
A
L
L
O
O
N
N
E
E
R
Load Straps (2)
Kayak Blocks (2)Safety Tied-downs (2)
● For vehicles with cross rails: Place the kayak onto the Blocks so that it is aligned and the weight of the kayak
is evenly distributed on each Block.
● For vehicles without cross rails: Reposition the blocks until the kayak weight is evenly distributed
on each block.
● For vehicles with cross rails: Fit the Blocks onto the cross bars with the bottom prole of each block fully inserted
over each bar, and loosely add the load straps around the cross rails. Note: Cross rails should be a minimum of 24”
apart.
● For vehicles without cross rails: Place the 2 foam blocks onto the roof of the vehicle. Locate blocks as close to
front and rear of vehicle roof as possible. Note: First clean the roof of all dirt and dust.
3
Installation & Loading Instructions - Please Read Before Beginning
1
. Place the kayak onto the Blocks so that it
is aligned and the weight of the kayak is
evenly distributed on each Block.
See image 2.
. Unroll the Load Straps. Open the vehicle’s doors.
Throw the non-buckle ends of the Straps up and
over the kayak and down to the other side of the
vehicle. Center the Straps with the foam blocks.
See image 3.
12’ Bow & Stern Lines
15’ Load Straps
2
Kayak Blocks
MPG166
Step 1: Positioning Blocks & Loading Kayak
. Confirm that the Blocks and roof of the vehicle
are clean and free of dust and dirt. Do not place
Blocks on a sun roof.
For installation without cross bars; center the
Blocks on the vehicle’s roof. Maintain a minimum
of 24” between the Blocks. See image 1.
For installation with cross bars; fit the Blocks
onto the cross bars with the bottom profile of
each block fully inserted over each bar.
ROOF TOP TRANSPORT KIT
K
ARRIERAYAK
C
M
M
A
A
L
L
O
O
N
N
E
E
R
3
Installation & Loading Instructions - Please Read Before Beginning
1
. Place the kayak onto the Blocks so that it
is aligned and the weight of the kayak is
evenly distributed on each Block.
See image 2.
. Unroll the Load Straps. Open the vehicle’s doors.
Throw the non-buckle ends of the Straps up and
over the kayak and down to the other side of the
vehicle. Center the Straps with the foam blocks.
See image 3.
12’ Bow & Stern Lines
15’ Load Straps
2
Kayak Blocks
MPG166
Step 1: Positioning Blocks & Loading Kayak
. Confirm that the Blocks and roof of the vehicle
are clean and free of dust and dirt. Do not place
Blocks on a sun roof.
For installation without cross bars; center the
Blocks on the vehicle’s roof. Maintain a minimum
of 24” between the Blocks. See image 1.
For installation with cross bars; fit the Blocks
onto the cross bars with the bottom profile of
each block fully inserted over each bar.
ROOF TOP TRANSPORT KIT
K
ARRIERAYAK
C
M
M
A
A
L
L
O
O
N
N
E
E
R
MPG155
&
MPG166
Combined Instructions
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
MALONE
R
● Attach the hook to the 1/4” tie-down rope. Secure the hook and rope to the forward (bow) end of the
kayak.
● Pull the free end down and secure to front of the vehicle. Repeat for the rear (stern) end of the kayak
and vehicle.
● Confirm the front and rear tie-downs are tight and kayak is firmly secured to vehicle. Check set-up
after 5 miles.
● For vehicles with cross rails: Place the strap loops over the kayak so that each loop is positioned directly
over a foam block. Pull the free end of each strap down until the buckles are positioned half way up the side of the
kayak. Thread the free strap ends around the cross rail and back through the buckles. Pulling down to tighten.
● For vehicles without cross rails: Open the vehicle’s doors and throw the non-buckle end of the 15’
load straps up and over the middle of the kayak and down to the other side of the vehicle. Pull both
ends together and buckle from the inside of the vehicle. Confirm the strap is tight & secure.
3
Installation & Loading Instructions - Please Read Before Beginning
1
. Place the kayak onto the Blocks so that it
is aligned and the weight of the kayak is
evenly distributed on each Block.
See image 2.
. Unroll the Load Straps. Open the vehicle’s doors.
Throw the non-buckle ends of the Straps up and
over the kayak and down to the other side of the
vehicle. Center the Straps with the foam blocks.
See image 3.
12’ Bow & Stern Lines
15’ Load Straps
2
Kayak Blocks
MPG166
Step 1: Positioning Blocks & Loading Kayak
. Confirm that the Blocks and roof of the vehicle
are clean and free of dust and dirt. Do not place
Blocks on a sun roof.
For installation without cross bars; center the
Blocks on the vehicle’s roof. Maintain a minimum
of 24” between the Blocks. See image 1.
For installation with cross bars; fit the Blocks
onto the cross bars with the bottom profile of
each block fully inserted over each bar.
ROOF TOP TRANSPORT KIT
K
ARRIERAYAK
C
M
M
A
A
L
L
O
O
N
N
E
E
R
MALONE
R
Installation & Loading Instructions - MPG166 Standard Kayak Kit
. With the doors open, pull both ends of the
straps together and buckle from the inside
of the vehicle. Confirm the straps are tight
and secure. See image 4.
13
Always check mounting hardware, load straps and safety tie-down lines for proper
and secure attachment before transport. Use of this product for any other
application other than kayak transport voids warranty.
Limit transport distance to 250 miles or less. Warning, this product is not
to be used as a flotation device.
Proudly Made In The USA
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: technical@maloneautoracks.com
Warning: All vehicular rooftop transports are potentially hazardous.
Any person using MALONE automotive transport systems is personally
responsible for following the given directions for use and installation
and accepts full and complete responsibility for any and all damages
or injury of any kind including death, which may result from their use.
4
5
. Install the bow and stern Safety Tie-downs
per the attached instructions.
Bow and stern safety tie-downs are required for all Malone rooftop transport(s).
Failure to correctly install and use safety tie-down lines voids all warranty and liability.
MPG306 BOW & STERN LINE KIT
MALONE
R
Thread free end
of cord through
hook.
Create a “left
over right”
knot & tighten.
Create a “right
over left”
knot & tighten.
Pull to test for
knot strength.
A B C D
Attach hook to rope (steps A-D)
Keeping the rope tight and
S-hook in place, thread the
free end up and through a
strong point on the kayak
F
Make a loop in the rope
12” to 14” away
from the kayak or canoe.
G
Attach and dress rope to vehicle and boat (steps E-O)
Attach S-hook to vehicle
tow ring or other sturdy
body part.
E
Bend the loop over leaving
a large opening as shown.
H
Opening
Pass the loop through the
opening.
I
Pull to create a tight knot.
JK
Thread the free end of
the rope
through the loop.
L
Pull the free end up until
the rope
is sufficiently tight.
M
Hold the rope secure with
one hand.
Form a knot with the free
end and tighten. Form
a second knot for
safety purposes.
N
The line should be tight
and secure. Repeat for
second tie-down.
O
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: technical@maloneautoracks.com
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
MPG306 BOW & STERN LINE KIT
NOTE: NOT REQUIRED ON TRAILER PACKAGES
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
Limited One (1) Year Warranty
The Malone Auto Racks (Malone) Limited 1 Year Warranty covers certain Malone-brand products that have been specically
identied for inclusion in the program. This warranty is in eect for one (1) year, from the time of sale, for the original retail purchaser
of the product. This warranty is terminated if the original retail purchaser sells or otherwise transfers the product to any other person
or entity.
Subject to the limitations and exclusions described in this warranty, Malone will remedy defects in materials and/or workmanship
by repairing or replacing, at its option, a defective product without charge for parts or labor. Malone may elect, at its option, not to
repair or replace a defective product but rather issue to the original retail purchaser a refund equal to the purchase price paid for the
product, or credit to be used toward the purchase of a replacement Malone product.
This warranty does not cover, and no warranty is given for defects or problems caused by normal wear and tear, which includes,
but is not limited to, surface (aesthetic) metal corrosion, scratches, dents, deformities, accidents, unlawful vehicle operation, or any
modication of a product not performed or authorized in writing by Malone.
In addition, this warranty does not cover problems resulting from conditions beyond Malone’s control including, but not limited to,
theft, misuse, overloading, or failure to assemble, mount or use the product in accordance with Malone’s written instructions or
guidelines included with the product provided to the original retail purchaser.
No warranty is given for Malone products purchased outside of the continental United States, Canada and Mexico.
If the product is believed to be defective, the original retail purchaser should contact the Malone dealer from whom it was purchased,
who will give the original retail purchaser instructions on how to proceed. If the original retail purchaser is unable to contact the
Malone dealer, or the dealer is not able to remedy the defect, the original retail purchaser should contact Malone by email at
In the event that the product must be returned to Malone, a technician at the email address above will provide the original purchaser
with return shipping instructions. The original purchaser will be responsible for the cost of mailing the product to Malone. In order
to be eligible to receive any remedy under this warranty, a copy of the original purchase receipt, a description of the defect and a
return address must be provided.
Disclaimer of Liability
Repair or replacement of a defective product, or the issue of a refund or credit (as determined by Malone) is the original retail
purchaser’s sole and exclusive remedy under this warranty. Damage to original purchaser’s vehicle, cargo, or property, and/ or to
any other person or property is not covered by this warranty.
This warranty is expressly made in lieu of any and all other warranties, express or implied, including the warranties of merchantability
and tness of a particular purpose
Malone’s sole liability to any purchaser is limited to the remedy set forth above. In no event will Malone be liable for any direct,
indirect, consequential, incidental, special, exemplary, or punitive damages , or, for any other damages of any kind or nature
(including but not limited to, lost prots, lost income or lost sales).
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not be
applicable.
In addition, all vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for
following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind
including death, which may result from their use and/or installation.
MALONE
R
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
- English: Malone MPG155 User manual
Documents connexes
-
Malone MPG187 Manuel utilisateur
-
Malone MPG125 Manuel utilisateur
-
Malone MPG537 Manuel utilisateur
-
Malone MPG398 Manuel utilisateur
-
Malone MPG113MD Manuel utilisateur
-
Malone MPG462G2 Manuel utilisateur
-
Malone MPG452 Manuel utilisateur
-
Malone MPG6188 Manuel utilisateur
-
Malone MPG201 Manuel utilisateur
-
Malone BIGFOOT Installation & Loading Instructions
