Malone MPG187 Manuel utilisateur

Taper
Manuel utilisateur
6” Foam Block
Canoe Kit
MPG187
MALONE
R
6” Foam Block
Canoe Kit
MALONE
R
DownLoaderDownLoaderTM
J-STYLE FOLDING KAYAK CARRIER
12’ Safety LinesJawz Universal Adapters Mounting BoltsKayak Carriers Load Straps T-Knobs
60mm
70mm
Installation & Loading Instructions - Please Read Before Beginning
Veuillez lire les instructions avant d’entreprendre l’installation et le chargement
1
3
2
. Insert Mounting Bolt through one hole of a Jawz adapter.
Insert washer and loosely apply a T-knob. See image 2.
. Faites passer le boulon de fixation dans l’un des trous
d’un adaptateur Jawz puis vissez légèrement un bouton
en ‘‘T’’ à la base du boulon. (Figure 2)
. Prior to installation, insert a bolt into the mounting holes in
the bottom of the carriers. Push upward to open the two
mounting hole covers located in the Base pads.
. Insert a Mounting Bolt into one mounting hole from the top
side. Rotate and close the mounting hole cover.
See image 1.
. Insérez un boulon de fixation dans l’un des trous hexagonaux
situés sur le côté supérieur du support.
(Figure 1)
. Place the carrier onto the front cross bar with the boarding
ramp facing out. Swing the Jawz under the cross bar as
shown. See image 3.
. Placez le support sur la barre transversale avant, la rampe
de chargement vers l’extérieur. Faites passer l’adaptateur
Jawz sous la barre transversale, tel qu’indiqué. (Figure 3)
1
Mounting Bolt Washers
Base Pad
Covers
IMPORTANT WARNING: All vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for
following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind including death,
which may result from their use and/or installation.
It is critical that all Malone racks and accessories be properly and securely attached to your vehicle. Improper attachment could result in a serious
accident, and could cause serious bodily injury or death to you or to others. You are responsible for securing the racks and accessories to your car,
checking the attachment’s prior to use, and periodically inspecting the products for adjustment, wear, and damage.
You must read and understand all of the instructions and cautions supplied with your Malone products(s) prior to installation or use. If you do not
understand all of the instructions and cautions, or, if you have no mechanical experience and are not thoroughly familiar with the installation
procedures, you should have the product installed by a professional installer.
MISE EN GARDE IMPORTANTE: Tout transport d’un chargement sur le toit d’un véhicule est potentiellement dangereux. Une personne qui
utilise les produits Malone doit suivre sans faute les instructions d’installation et d’utilisation fournies et assume l’entière responsabilité pour tout
dommage ou toute blessure, y compris un décès, pouvant résulter d’une telle installation ou utilisation.
Il est essentiel de xer correctement et solidement les supports et les accessoires à votre véhicule. Une mauvaise installation ou attache pourrait
provoquer un accident, entraîner des blessures corporelles graves à vous et aux autres et même causer la mort. Vous avez la responsabilité de
xer solidement les supports et les accessoires à votre véhicule, de vérier l’installation avant l’utilisation et d’inspecter périodiquement le produit
pour déceler tout signe d’usure ou de dommage ou tout problème d’ajustement.
Vous devez lire et comprendre les instructions et les mises en garde fournies avec les produits Malone avant l’installation et l’utilisation. Si vous
ne comprenez pas les instructions et les mises en garde ou si vous ne possédez pas d’expérience en mécanique et ne connaissez pas à fond les
procédures à suivre d’installation, vous devriez faire monter et poser le produit par un installateur professionnel.
Important Note
Product Warranty & Registration Form
All information is condential and used exclusively by MALONE only.
MALONE
R
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
Dear Customer,
Thank you for your purchase of a Malone Product.
In order to be eligible for the Malone Warranty program, we ask that you contact us online at the link provided
below: With-in 30 days of purchase. You can also mail this letter back to the address at the bottom.
• Online: https://maloneautoracks.com/product-registration.php
We will require the information below.
Here is the information collected:
First Name:
Last Name:
Address:
Address2:
City:
State:
Zip:
Country:
Email:
Phone:
Product Description/Name:
Product MPG#
Date Purchased:
Store Where Purchased:
Purchase Price:
Thank you for choosing Malone!
INSTRUCTIONS
C
ARRIERANOE
C
MALONE AUTO RACKS
81 County Road
Westbrook, Maine USA 04092
Web: www.maloneautoracks.com
Warning: All vehicular rooftop transports are potentially hazardous.
Any person using MALONE automotive transport systems is personally
responsible for following the given directions for use and installation
and accepts full and complete responsibility for any and all damages
or injury of any kind including death, which may result from their use.
PLEASE READ ALL INSTRUCTIONS PRIOR TO INSTALLATION
3
4
1
2
MPG175
Finishing the Installation:
Follow the attached instructions for the MPG306 Bow & Stern lines.
Confirm the lines are tight and the canoe is firmly secured to the
vehicle. Check the set-up for tighteness and overall safety after 5
miles of travel.
For Vehicles without Cross Rails:
Install the four foam blocks to the gunwale as shown. Note: The
large oval cut-outs on the blocks should be facing up.
Measure and locate the blocks so that the forward set of two are
approximately 1/3 the distance from the front of the canoe. Repeat
for the rear set of two and back of canoe.
Carefully load the canoe, bottom up, onto the vehicle’s roof. We
strongly advise two people for this process.
Slightly reposition the blocks until the weight of the canoe is evenly
distributed across all four blocks. Note: Clean the roof prior to loading
the canoe.
Throw the non-buckle ends of the load straps up and over the canoe.
Open the vehicle’s front and rear doors. From the far side, dress the
strap free ends through the vehicle. Insert the free ends through the
buckles and firmly pull down to tighten.
For Vehicles with Cross Rails:
Install the four foam blocks to the gunwale as shown. Note: The
large oval cut-outs on the blocks should be facing up.
Measure and locate the blocks to match the distance between the
cross rails. Note: Cross rails should be a minimum of 40” apart.
Carefully load the canoe, bottom up, onto the vehicle’s roof and cross
rails. We strongly advise two people for this process.
Slightly reposition the blocks until the weight of the canoe is evenly
distributed across all four blocks.
Throw the non-buckle ends of the load straps up and over the canoe.
From the far side, dress the straps under the cross rails and back
over the canoe. Insert the strap free ends into the buckles and pull
down to tighten. Wrap excess strap length around the cross rails.
MALONE
R
For Vehicles without Cross Rails:
Install the four foam blocks to the gunwale as shown. Note: The
large oval cut-outs on the blocks should be facing up.
Measure and locate the blocks so that the forward set of two are
approximately 1/3 the distance from the front of the canoe.
Repeat for the rear set of two and back of canoe.
Carefully load the canoe, bottom up, onto the vehicle’s roof. We
strongly advise two people for this process.
Slightly reposition the blocks until the weight of the canoe is
evenly distributed across all four blocks. Note: Clean the roof
prior to loading the canoe.
1
2
MPG187
For Vehicles With Cross Rails:
Install the four foam blocks to the gunwale as shown. Note: The
large oval cut-outs on the blocks should be facing up.
Measure and locate the blocks to match the distance between the
cross rails. Note: Cross rails should be a minimum of 24” a part.
Carefully load the canoe, bottom up, onto the vehicle’s roof and
cross rails. We strongly advise two people for this process.
Slightly reposition the blocks until the weight of the canoe is evenly
distributed across all four blocks.
Throw the non-buckle ends of the load straps up and over the ca-
noe. From the far side, dress the straps under the cross rails and
back over the canoe. Insert the strap free ends into the
buckles and pull down to tighten. Wrap excess strap length around
the cross rails.
3
Throw the non-buckle ends of the load straps up and over the
canoe. Open the vehicle’s front and rear doors. From the far side,
dress the strap free ends through the vehicle. Insert the free ends
through the buckles and rmly pull down to tighten.
Finishing the Installation: Follow the
attached instructions for the MPG306
Bow & Stern lines. Conrm the lines
are tight and the canoe is rmly se-
cured to the vehicle. Check the set-up
for tightness and overall safety after
5miles of travel.
NOTE: Bow and stern safety tie-downs are
required for all Malone rooftop transport(s).
Failure to correctly install and use safety tie-
down lines voids all warranty and liability.
6” Foam Block
Canoe Kit
MPG306 BOW & STERN LINE KIT
MALONE
R
Thread free end
of cord through
hook.
Create a “left
over right”
knot & tighten.
Create a “right
over left”
knot & tighten.
Pull to test for
knot strength.
A B C D
Attach hook to rope (steps A-D)
Keeping the rope tight and
S-hook in place, thread the
free end up and through a
strong point on the kayak
F
Make a loop in the rope
12” to 14” away
from the kayak or canoe.
G
Attach and dress rope to vehicle and boat (steps E-O)
Attach S-hook to vehicle
tow ring or other sturdy
body part.
E
Bend the loop over leaving
a large opening as shown.
H
Opening
Pass the loop through the
opening.
I
Pull to create a tight knot.
JK
Thread the free end of
the rope
through the loop.
L
Pull the free end up until
the rope
is sufficiently tight.
M
Hold the rope secure with
one hand.
Form a knot with the free
end and tighten. Form
a second knot for
safety purposes.
N
The line should be tight
and secure. Repeat for
second tie-down.
O
MALONE AUTO RACKS, 81 County Road, Westbrook, Maine 04092
Phone: 207-774-9100 Fax: 207-615-0551
Website: www.maloneautoracks.com Email: technical@maloneautoracks.com
MPG187
MPG306 BOW & STERN LINE KIT
NOTE: NOT REQUIRED ON TRAILER PACKAGES
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
MALONE AUTO RACKS 81 County Rd. Ste 1, Westbrook, ME 04092
P: 207.774.9100 F: 207.615.0551
E: support@maloneautoracks.com W: www.maloneautoracks.com
Limited One (1) Year Warranty
The Malone Auto Racks (Malone) Limited 1 Year Warranty covers certain Malone-brand products that have been specically
identied for inclusion in the program. This warranty is in eect for one (1) year, from the time of sale, for the original retail purchaser
of the product. This warranty is terminated if the original retail purchaser sells or otherwise transfers the product to any other person
or entity.
Subject to the limitations and exclusions described in this warranty, Malone will remedy defects in materials and/or workmanship
by repairing or replacing, at its option, a defective product without charge for parts or labor. Malone may elect, at its option, not to
repair or replace a defective product but rather issue to the original retail purchaser a refund equal to the purchase price paid for the
product, or credit to be used toward the purchase of a replacement Malone product.
This warranty does not cover, and no warranty is given for defects or problems caused by normal wear and tear, which includes,
but is not limited to, surface (aesthetic) metal corrosion, scratches, dents, deformities, accidents, unlawful vehicle operation, or any
modication of a product not performed or authorized in writing by Malone.
In addition, this warranty does not cover problems resulting from conditions beyond Malone’s control including, but not limited to,
theft, misuse, overloading, or failure to assemble, mount or use the product in accordance with Malone’s written instructions or
guidelines included with the product provided to the original retail purchaser.
No warranty is given for Malone products purchased outside of the continental United States, Canada and Mexico.
If the product is believed to be defective, the original retail purchaser should contact the Malone dealer from whom it was purchased,
who will give the original retail purchaser instructions on how to proceed. If the original retail purchaser is unable to contact the
Malone dealer, or the dealer is not able to remedy the defect, the original retail purchaser should contact Malone by email at
In the event that the product must be returned to Malone, a technician at the email address above will provide the original purchaser
with return shipping instructions. The original purchaser will be responsible for the cost of mailing the product to Malone. In order
to be eligible to receive any remedy under this warranty, a copy of the original purchase receipt, a description of the defect and a
return address must be provided.
Disclaimer of Liability
Repair or replacement of a defective product, or the issue of a refund or credit (as determined by Malone) is the original retail
purchaser’s sole and exclusive remedy under this warranty. Damage to original purchaser’s vehicle, cargo, or property, and/ or to
any other person or property is not covered by this warranty.
This warranty is expressly made in lieu of any and all other warranties, express or implied, including the warranties of merchantability
and tness of a particular purpose
Malone’s sole liability to any purchaser is limited to the remedy set forth above. In no event will Malone be liable for any direct,
indirect, consequential, incidental, special, exemplary, or punitive damages , or, for any other damages of any kind or nature
(including but not limited to, lost prots, lost income or lost sales).
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not be
applicable.
In addition, all vehicular transports are potentially hazardous. Any person(s) using Malone products are personally responsible for
following the given directions for use and/or installation and accepts full responsibility for any and all damages or injury of any kind
including death, which may result from their use and/or installation.
MALONE
R
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Malone MPG187 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues