ASROCK 775XFire-RAID Le manuel du propriétaire

11

1

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published February 2006

22

2

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 Chassis Fan Connector (CHA_FAN1)

2 ATX 12V Connector (ATX12V1) 17 System Panel Header (PANEL1)

3 ATX Power Connector (ATXPWR1) 18 Chassis Speaker Header (SPEAKER 1)

4 775-Pin CPU Socket 19 Infrared Module Connector (IR1)

5 North Bridge Controller 20 USB 2.0 Header (USB67, Blue)

6 CPU Fan Connector (CPU_FAN1) 21 USB 2.0 Header (USB45, Blue)

7 2 x 240-pin DDRII DIMM Slots 22 Floppy Connector (FLOPPY1)

(Dual Channel A: DDRII_1, DDRII_3; Yellow) 23 Game Port Header (GAME1)

8 2 x 240-pin DDRII DIMM Slots 24 Front Panel Audio Header (HD_AUDIO1)

(Dual Channel B: DDRII_2, DDRII_4; Orange) 25 PCI Slots (PCI1- 3)

9 IDE1 Connector (IDE1, Blue) 26 BIOS FWH Chip

10 Clear CMOS Jumper (CLRCMOS1) 27 AGI Express Slot (PCI Express x 4)

11 South Bridge Controller 28 PCIEX1_EN1 - 5

12 Serial ATA Connector 2 (SATA_2, black) 29 PCI Express x 1 Slot (PCIE2)

13 Serial ATA Connector 3 (SATA_3, black) 30 PCI Express x 16 Slot (PCIE1)

14 Serial ATA Connector 1 (SATA_1, blue) 31 SLI / XFIRE Power Connector

15 Serial ATA Connector 0 (SATA_0, blue) 32 Internal Audio Connector: CD1 (Black)

33

3

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

HD 8CH I/OHD 8CH I/O

HD 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 Serial Port: COM1

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4VV----

6 VVV--

8 VVVV

* If you use 8-channel audio and enable Multi-Streaming function, “Side Speaker” will be disabled

. Therefore, only 6-channel audio function will work but not 8-channel audio. To enable Multi-

Streaming function, you need to connect a front panel audio cable to the front panel audio

header. After restarting your computer, you will find “Mixer” tool on your system. Please select

“Mixer ToolBox” , click “Enable playback multi-streaming”, and click “ok”. Choose

“2CH”, “4CH”, or “6CH”, and then you are allowed to select “Realtek HDA Primary output” to use

Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA Audio 2nd output” to

use front panel audio to share Side Speaker.

44

4

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock 775XFire-RAID motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might be

updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock website

as well. ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock 775XFire-RAID Motherboard

(ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm)

ASRock 775XFire-RAID Quick Installation Guide

ASRock 775XFire-RAID Support CD

(including LGA 775 CPU Installation Live Demo)

One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Data Cable (Optional)

One Serial ATA (SATA) HDD Power Cable (Optional)

One HD 8CH I/O Panel Shield

55

5

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm

CPU - LGA 775 for Intel

®

Pentium

®

4 / Celeron

®

D, supporting Cedar

Mill processors (in 775-land LGA package)

- FSB 800/533 MHz

- Supports Hyper-Threading Technology (see CAUTION 1)

- Supports EM64T CPU

Chipset - Northbridge: Intel

®

925X chipset

- Southbridge: Intel

®

ICH6R

Memory - Dual Channel DDRII Memory Technology (see CAUTION 2)

- 4 x DDRII DIMM slots

- Support DDRII533

- Max. capacity: 4GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 3)

- ASRock U-COP (see CAUTION 4)

- Boot Failure Guard (B.F.G.)

Expansion Slot - Supports ATI

®

CrossFire

TM

- 3 x PCI slots

- 1 x PCI Express x 16 slot

- 1 x AGI Express slot (PCI Express x 4) (see CAUTION 5)

- 1 x PCI Express x 1 slot

Audio - Realtek ALC861 7.1 channel CODEC with High Definition

Audio

LAN - Realtek PCI LAN 8101L

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O HD 8CH I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 Port

- Audio Jack: Side Speaker/Rear Speaker/Central Bass/Line

in/Front Speaker/Microphone (see CAUTION 6)

66

6

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Connector - 4 x Serial ATA 1.5Gb/s connectors, support RAID (RAID 0,

RAID 1, and Intel Matrix Storage) and “Hot Plug” functions

- 1 x ATA100 IDE connector (supports 2 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- SLI/XFIRE power connector

- CD in header

- Front panel audio connector

- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

(see CAUTION 7)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

Support CD - Drivers, Utilities, AntiVirus Software

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Overheat Shutdown to Protect CPU Life

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000/XP/XP 64-bit compliant

Certifications - FCC, CE, WHQL

77

7

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 36

of “User Manual” in the Support CD.

2. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 12 for proper installation.

3. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

4. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

5. If you install PCI Express VGA card to AGI Express slot (PCI Express x

4), PCIE2 slot (PCIE x 1) function will be disabled. For the information of

the compatible PCI Express VGA cards, please refer to the “Supported PCI

Express VGA Card List for AGI Express Slot (PCI Express x 4)” on page

8. For the proper installation of PCI Express VGA card, please refer to the

installation guide on page 14.

6. For microphone input, this motherboard supports both stereo and mono

modes. For audio output, this motherboard supports 2-channel, 4-channel,

6-channel, and 8-channel modes. Please check the table on page 3 for

proper connection.

7. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 or SP2 / 2000 SP4.

88

8

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

1.31.3

1.3

Supported PCI Express VGA Card List for AGISupported PCI Express VGA Card List for AGI

Supported PCI Express VGA Card List for AGI

Express Slot (PCI Express x 4)Express Slot (PCI Express x 4)

Express Slot (PCI Express x 4)

(for Windows 2000/Windows XP)

Graphics Chip Model Name Chipset Name

Vendor

NVIDIA

ATI

For the latest updates of the supported PCI Express VGA card list for AGI Express

slot (PCI Express x 4), please visit our website for details.

ASRock website:

http://www.asrock.com/support/index.htm

Note. It is not recommended to use Turbo cache PCI Express x 16 VGA cards.

ASUS Extreme N6200GE/TD GeForce 6200

ASUS Extreme N6200TC256/TD GeForce 6200

ASUS Extreme N6800/TD GeForce 6800

ASUS Extreme N6800GT GeForce 6800GT

ALBATRON PC6600GT GeForce 6600GT

GIGABYTE GV-NX66128D GeForce 6600

Inno3D GeFORCE 6600 LE GeForce 6600LE

LEADTEK PX6200 TC/TDH GeForce 6200TC

MSI PCX 5750-TD128E GeForce PCX5750

SPARKLE GeFORCE 6200TC GeForce 6200TC

ASUS Extreme AX600XT/HTVD RADEON X600XT

ASUS Extreme AX700PRO/TVD RADEON X700PRO

GECUBE Radeon X850XT 256M RADEON X850XT

MSI RX1300GPRO-TD256E RADEON X1300 PRO

99

9

ASRock 775XFire-RAID Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the carpet

or the like. Also remember to use a grounded wrist strap or touch

a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the

screws! Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

For the installation of Intel 775-LAND CPU,

please follow the steps below.

Before you insert the 775-LAND CPU into the socket, please check if

the CPU surface is unclean or if there is any bent pin on the socket.

Do not force to insert the CPU into the socket if above situation is

found. Otherwise, the CPU will be seriously damaged.

775-Pin Socket Overview

EnglishEnglish

English

1010

10

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Step 1. Open the socket:

Step 1-1. Disengaging the lever by depressing

down and out on the hook to clear

retention tab.

Step 1-2. Rotate the load lever to fully open po-

sition at approximately 135 degrees.

Step 1-3. Rotate the load plate to fully open po-

sition at approximately 100 degrees.

Step 2. Insert the 775-LAND CPU:

Step 2-1. Hold the CPU by the edges where are

marked with black lines.

Step 2-2. Orient the CPU with IHS (Integrated

Heat Sink) up. Locate Pin1 and the two

orientation key notches.

For proper inserting, please ensure to match the two orientation key

notches of the CPU with the two alignment keys of the socket.

Step 2-3. Carefully place the CPU into the socket

by using a purely vertical motion.

Step 2-4. Verify that the CPU is within the socket

and properly mated to the orient keys.

Step 3. Remove PnP Cap (Pick and Place Cap):

Use your left hand index finger and thumb to

support the load plate edge, engage PnP cap

with right hand thumb and peel the cap from the

socket while pressing on center of PnP cap to

assist in removal.

black line

775-Pin Socket

Pin1

alignment key

Pin1

orientation

key notch

orientation

key notch

775-LAND CPU

1111

11

ASRock 775XFire-RAID Motherboard

1. It is recommended to use the cap tab to handle and avoid kicking

off the PnP cap.

2. This cap must be placed if returning the motherboard for after

service.

Step 4. Close the socket:

Step 4-1. Rotate the load plate onto the IHS.

Step 4-2. While pressing down lightly on load

plate, engage the load lever.

Step 4-3. Secure load lever with load plate tab

under retention tab of load lever.

2.22.2

2.2

Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

Installation of CPU Fan and Heatsink

For proper installation, please kindly refer to the instruction manuals of your CPU fan

and heatsink.

Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.

Step 1. Apply thermal interface material onto center

of IHS on the socket surface.

Step 2. Place the heatsink onto the socket. Ensure

fan cables are oriented on side closest to the

CPU fan connector on the motherboard

(CPU_FAN1, see page 2, No. 6).

Step 3. Align fasteners with the motherboard

throughholes.

Step 4. Rotate the fastener clockwise, then press

down on fastener caps with thumb to install

and lock. Repeat with remaining fasteners.

If you press down the fasteners without rotating them clockwise,

the heatsink cannot be secured on the motherboard.

Step 5. Connect fan header with the CPU fan

connector on the motherboard.

Step 6. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or

contact other components.

EnglishEnglish

English

1212

12

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

2.3 Installation of Memory Modules (DIMM)2.3 Installation of Memory Modules (DIMM)

2.3 Installation of Memory Modules (DIMM)

775XFire-RAID motherboard provides four 240-pin DDRII (Double Data Rate II)

DIMM slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install identical (the same brand, speed,

size and chip-type) DDRII DIMM pair in the slots of the same color. In other words,

you have to install identical DDRII DIMM pair in Dual Channel A (DDRII_1 and

DDRII_3; Yellow slots; see p.2 No.7) or identical DDRII DIMM pair in Dual Chan-

nel B (DDRII_2 and DDRII_4; Orange slots; see p.2 No.8), so that Dual Channel

Memory Technology can be activated. This motherboard also allows you to

install four DDRII DIMMs for dual channel configuration, and please install iden-

tical DDRII DIMMs in all four slots. You may refer to the Dual Channel Memory

Configuration Table below.

Dual Channel Memory Configurations

DDRII_1 DD RII_2 DDRII_3 DDRII_4

(Yellow Slot) (Orange Slot) (Yellow Slot) (Orange Slot)

(1) Populated - Populated -

(2) - Populated - Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDRII DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of yellow

slots (DDRII_1 and DDRII_3), or in the set of orange slots (DDRII_2

and DDRII_4).

2. If only one memory module or three memory modules are installed

in the DDRII DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDRII_1

and DDRII_2, it is unable to activate the Dual Channel Memory

Technology .

4. It is not allowed to install a DDR memory module into DDRII slot;

otherwise, this motherboard and DIMM may be damaged.

1313

13

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

1414

14

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

2.4 Expansion Slots (PCI, PCI Express, and AGI Express2.4 Expansion Slots (PCI, PCI Express, and AGI Express

2.4 Expansion Slots (PCI, PCI Express, and AGI Express

Slots) Slots)

Slots)

There are 3 PCI slots, 2 PCI Express slots, and 1 AGI Express slot (PCI Express x 4)

on this motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots: PCIE1 (PCIE x 16 slot) is used for PCI Express cards with x16 lane

width graphics cards.

PCIE2 (PCIE x 1 slot) is used for PCI Express cards, such as

Gigabit LAN card, SATA2 card, etc. Please check the jumper set

tings on page 15 for different functions.

AGI Express slot (PCI Express x 4):

AGI Express slot (PCI Express x 4) is used to install PCI Express expan-

sion cards. For the information of the compatible PCI Express VGA cards,

please refer to the “Supported PCI Express VGA Card List for AGI Ex-

press Slot (PCI Express x 4)” on page 8. Please check the jumper set-

tings on page 15 for different functions.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

2.5 Dual Graphics Feature2.5 Dual Graphics Feature

2.5 Dual Graphics Feature

This motherboard supports Dual Graphics Technology. When installing the add-on

VGA cards to this motherboard, you are allowed to choose two different ways to

decide the function of PCIE2 slot (PCIE x 1) and AGI Express slot. The default value

of this feature is to enable PCIE2 slot (PCIE x 1) and AGI Express slot (only PCI

Express x 1). You can also adjust the jumpers to disable PCIE2 slot (PCIE x 1). Then

only AGI Express slot (PCI Express x 4) will be enabled. In other words, you are able

to adjust the jumpers to enjoy the benefit of Dual Graphics feature. Please refer to the

table below for the correct jumper settings.

1515

15

ASRock 775XFire-RAID Motherboard

Function Jumper Settings

PCIE x 1_EN4

PCIE x 1_EN3

PCIE x 1_EN2

PCIE x 1_EN1

PCIE x 1_EN4

PCIE x 1_EN3

PCIE x 1_EN2

PCIE x 1_EN1

EnglishEnglish

English

Enable

PCIE2 /

AGI Express

(only PCIE x 1)

(Default)

Enable

AGI Express

(PCIE x 4)

(Disable PCIE2)

PCIE x 1_EN5

2.6 CrossFire2.6 CrossFire

2.6 CrossFire

TMTM

TM

Operation Guide Operation Guide

Operation Guide

This motherboard supports CrossFire

TM

feature. CrossFire

TM

technology offers the

most advantageous means available of combining multiple high performance Graphics

Processing Units (GPU) in a single PC. Combining a range of different operating

modes with intelligent software design and an innovative interconnect mechanism,

CrossFire

TM

enables the highest possible level of performance and image quality in

any 3D application. Currently CrossFire

TM

feature is only supported with Windows

XP with Service Pack 2; it may be supported with other OS in the future.

1616

16

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

1. If a customer incorrectly configures their system they will not see the

performance benefits of CrossFire

TM

. All three CrossFire

TM

components, a

CrossFire

TM

Ready graphics card, a CrossFire

TM

Ready motherboard and

a CrossFire

TM

Edition co-processor graphics card, must be installed

correctly to benefit from the CrossFire

TM

multi-GPU platform.

2. If you pair a 12-pipe CrossFire

TM

Edition card with a 16-pipe card, both

cards will operate as 12-pipe cards while in CrossFire

TM

mode.

Enjoy the benefit of CrossFireEnjoy the benefit of CrossFire

Enjoy the benefit of CrossFire

TMTM

TM

Step 1. Adjust the jumpers on this motherboard to enable AGI Express slot (PCI

Express x 4). Please refer to the pictures below for proper jumper setting.

Currently, ATI has released Radeon X850XT, X1800XT, X1300, and X1600

CrossFire

TM

cards, which require different methods to enable CrossFire

TM

feature. In the below procedures, we use Radeon X850XT as the example

graphics card. For other CrossFire

TM

cards that ATI has released or will

release in the future, please refer to ATI graphics card manuals for detailed

installation guide.

It is recommended to use 500-Watt power supply or greater

to perform the benefit of CrossFire

TM

feature.

Step 2. Connect to the system power supply. Please connect a hard

disk power connector to SLI/XFIRE Power connector.

PCIEx1_EN1-4: Short Pin1, Pin2

What graphics cards work with CrossFire

TM

?

A complete CrossFire

TM

system requires a CrossFire

TM

Ready motherboard,

a CrossFire

TM

Edition graphics card and a compatible standard Radeon

(CrossFire

TM

Ready) graphics card from the same series, or two CrossFire

TM

Ready cards if they are software enabled. This applies to cards from ATI or

any of its partners.

Cards For AGI Express Slot Cards For PCI Express Slot

Radeon X1800 Series Radeon X1800 CrossFire

TM

Edition

Radeon X1600 Series Radeon X1600 Series

Radeon X1300 Series Radeon X1300 Series

Radeon X850 Series Radeon X850 CrossFire

TM

Edition

PCIEx1_EN5: Short Pin1, Pin2

1717

17

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Step 3. Install the standard Radeon (CrossFire

TM

Ready) graphics card to AGI Ex-

press slot (PCI Express x 4). For the proper installation procedures, please

refer to section “Expansion Slots”.

Step 4. Install the Radeon CrossFire

TM

Edition graphics card to PCI Express x 16

slot. For the proper installation procedures, please refer to section “Expan-

sion Slots”.

DVI-DMS cable DMS connector

DVI connector

You are allowed to install two CrossFire

TM

Edition graphics cards to both slots,

or you may use one CrossFire

TM

Edition graphics cards and a compatible

standard Radeon (CrossFire

TM

Ready) graphics card from the same series.

Connect the DVI-DMS

cable to DVI connector of

the compatible standard

Radeon (CrossFire

TM

Ready) graphics card.

Standard Radeon

(CrossFire

TM

Ready)

graphics card

Standard Radeon

(CrossFire

TM

Ready)

graphics card

Radeon CrossFire

TM

Edition graphics card

DVI connector

Standard Radeon (CrossFire

TM

Ready)

graphics card

There are two DVI connectors on the

standard Radeon (CrossFire

TM

Ready)

graphics card. Please connect the DVI-DMS

cable to the correct DVI connector; otherwise

, the graphics card will not work.

ss Slot

re

TM

Edition

e

TM

Edition

Step 5. Correctly connect the DVI-DMS cable to the monitor connector and two

graphics cards that you install. (If you install two standard Radeon

(CrossFire

TM

Ready) graphics cards to this motherboard, please skip this

step.)

1, Pin2

1818

18

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

Step 6. Power on your computer and boot into OS.

Step 7. Remove the ATI driver if you have any VGA driver installed in your system.

If you install two CrossFire

TM

Edition graphics cards to this motherboard, please

connect one end of DVI-DMS cable to the monitor, another end to DMS of one

of the CrossFire

TM

Edition graphics cards to PCIE1 slot (PCI Express x 16), and

the other end to DVI of another CrossFire

TM

Edition graphics card to AGI

Express slot (PCI Express x 4). If you install one CrossFire

TM

Edition graphics

card and one compatible standard Radeon (CrossFire

TM

Ready) graphics card

to this motherboard, please connect one end of DVI-DMS cable to the monitor,

another end to DMS of the CrossFire

TM

Edition graphics card, and the other end

to DVI of the compatible standard Radeon (CrossFire

TM

Ready) graphics card.

Connect the DVI-DMS

cable to the monitor

connector.

Connect the DVI-DMS

cable to DMS connector

of the CrossFire

TM

Edition

graphics card.

The Catalyst Uninstaller is an optional download. We recommend using this

utility to uninstall any previously installed Catalyst drivers prior to installation.

Please visit this website for the driver:

http://support.ati.com/ics/support/DLRedirect.asp?

fileIDExt=050553d40196ef109fff37cbb40aaf28&accountID=737&deptID=894

Step 8. Install the required drivers to your system. Please visit the websites below

for installing the drivers that ATI recommends:

A. ATI recommends Windows XP Service Pack 2 or higher to be installed

(If you have Windows XP Service Pack 2 or higher installed in your

system, there is no need to download it again):

http://www.microsoft.com/windowsxp/sp2/default.mspx

B. You must have Microsoft .NET Framework installed prior to

downloading and installing the CATALYST Control Center:

http://www.microsoft.com/downloads/details.aspx?

FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en

DMS

connector

Radeon

CrossFire

TM

Edition graphics

card

Step 9. Restart your computer.

1919

19

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

t

o

If you install one Radeon CrossFire

TM

Edition graphics card and one compatible

standard Radeon (CrossFire

TM

Ready) graphics card to this motherboard but

not two Radeon CrossFire

TM

Edition graphics cards, please as well follow the

above steps. However, although you have selected the option “Enable

CrossFire

TM

”, the CrossFire

TM

function can not work actually. Your computer

will automatically reboot. After restarting your computer, please confirm whether

the option “Enable CrossFire

TM

” in “ATI Catalyst Control Center” is selected or

not; if not, please select it again, and then you are able to enjoy the benefit of

CrossFire

TM

feature.

Step 12. You can freely enjoy the benefit of CrossFire

TM

feature.

Step 11. Double-click “ATI Catalyst Control Center”. Click “View”, and select “Ad-

vanced View”. Click “CrossFire

TM

”, and then set the option “Enable

CrossFire

TM

” to “Yes”.

Step 10. Install the VGA card drivers to your system, and restart your computer.

Then you will find “ATI Catalyst Control Center” on your desktop (ATI

Catalyst driver should be version 5.10 or higher).

You will find “ATI Catalyst

Control Center” on your

desktop.

View

CrossFire

TM

Enable CrossFire

TM

* CrossFire

TM

appearing here is a registered trademark of ATI Technologies Inc., and is used only

for identification or explanation and to the owners’ benefit, without intent to infringe.

2020

20

ASRock 775XFire-RAID Motherboard

EnglishEnglish

English

2-pin jumper

Short Open

2.7 Surround Display Feature2.7 Surround Display Feature

2.7 Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on

PCI Express VGA card, you can easily enjoy the benefits of Surround Display

feature. For the detailed instruction, please refer to the document at the following

path in the Support CD:

..\ Surround Display Information

2.8 Jumpers Setup2.8 Jumpers Setup

2.8 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting Description

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS

(CLRCMOS1, 2-pin jumper)

(see p.2 No. 10)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on

CLRCMOS1 for 5 seconds.

La page charge ...

ASROCK 775XFire-RAID Le manuel du propriétaire

ASROCK 775XFire-RAID Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents