ATEN PE6108AV Manuel utilisateur

PE6108AV / PE6208AV / PE8208AV

8-Outlets eco PDU

User Manual

www.aten.com

PE6108AV / PE6208AV / PE8208AV User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

Warning: Operation of this equipment in a residential environment could

cause radio interference.

KCC Statement

이 기기는 업무용 (A 급 ) 전자파 적합기기로서 판매자 또는 사용

자는 이점을 주의하시기 바라며 , 가정외의 지역에서 사용하는

것을 목적으로합니다 .

RoHS

This product is RoHS compliant.

eco PDU PE Series User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual are subject

to change without prior notification by the manufacturer. The manufacturer makes no

representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims any warranties as to merchantability or fitness for any

particular purpose. Any of the manufacturer's software described in this manual is sold

or licensed as is. Should the programs prove defective following their purchase, the

buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of

all necessary servicing, repair and any incidental or consequential damages resulting

from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference

caused by unauthorized modifications to this device. It is the responsibility of the user

to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation of this

system if the correct operational voltage setting was not selected prior to operation.

PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.

If any bodily injury or property damage with respect to operation of the product results

from users not having installed the product in accordance with the instructions provided

in the product’s user manual, or the product is used in an environment with a current

load over the designed specifications of the product, ATEN is not liable for any loss or

damage.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

PE6108AV / PE6208AV / PE8208AV User Manual

iv

PE Device Safety Notice

Consignes de sècuritè relatives à l’unitè PE

 Installez sur le circuit du bâtiment des disjoncteurs permettant d’assurer la

protection maximale autorisée, en respectant le courant nominal spécifié sur la

plaque signalétique. Veuillez respecter l’ensemble des réglementations nationales

en vigueur et des codes de sécurité ainsi que les déviations recommandèes pour les

disjoncteurs.

 Ne connectez l’unité PE qu’à une prise de courant avec borne de terre ou à un

système mis à la terre!

 Assurez-vous que le courant d’entrée total des systèmes connectés ne dépasse pas

le courant nominal spécifié sur la plaque signalétique de l’unité PE.

 Il existe un risque d’explosion si la batterie est remplacée par une batterie de type

incorrect. Jetez les batteries usagées en respectant les instructions adequates.

 Set the maximum permissible breaker protection in the building circuitry to the

current rating specified on the rating plate. Observe all national regulations and

safety codes as well as deviations for breakers.

 Only connect the PE Device to a grounded power outlet or a grounded system!

 Make sure that the total current input of the connected systems does not exceed

the current rating specified on the rating plate of the PE Device.

 There is a risk of explosion if the battery is replaced with an incorrect type.

Dispose of used batteries according to the relevant instructions.

eco PDU PE Series User Manual

v

Package Contents

The eco PDU PE6108AV/6208AV Series package consists of:

 1 PE6108AVA/PE6208AVA/PE6208AVB/PE6208AVG/PE6208AVX

Power Distribution Unit

 1 Power Cord (not available for PE6208AVX)

 1 RJ-45 Cable

 10 Cable Ties (only for J plug)

 1 Footpad Set

 1 Mounting Kit

 1 User Instructions*

The eco PDU PE8208AV Series package consists of:

 1 PE8208AV Power Distribution Unit

 1 Power Cord

 1 RJ-45 Cable

 4 Cable Ties

 1 Footpad Set

 1 Mounting Kit

 1 User Instructions*

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the eco PDU installation.

* Features may have been added to the eco PDU since this manual was

published. Please visit our website to download the most up-to-date version.

Date Published: 2018-09-11

All other brand names and trademarks are the registered property of their respective owners.

PE6108AV / PE6208AV / PE8208AV User Manual

vi

Contents

EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

PE Device Safety Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Consignes de sècuritè relatives à l’unitè PE . . . . . . . . . . . . . . . . . . . . .iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1.Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Metering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Outlet Switch Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PE6108AV / PE6208AV / PE8208AV Front View . . . . . . . . . . . . . . . . . 6

PE6108AV / PE6208AV / PE8208AV Rear View (exclude PE6208AVX)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PE6208AVX Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2.Hardware Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Power Cord Installation (PE6208AVX) . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Cord Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Plug Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Securing the Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Securing the Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Chapter 3.Basic Operation and

eco PDU PE Series User Manual

vii

First Time Setup

Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Changing the Administrator Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Moving On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Chapter 4.Browser Operation

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

The eco PDU Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Page Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Energy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Configuration (PE6208AV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Configuration (PE8208AV) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

The System Log Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Notification Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Login Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Session Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Account Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Login String / IP Filter / Mac Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Authentication & Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

PDU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Firmware File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Backup/Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Chapter 5.RS-232 / Telnet Commands

Remote Terminal Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

RS-232 Serial Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Read Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

PE6108AV / PE6208AV / PE8208AV User Manual

viii

Switch Outlet Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Read Power Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Read Environmental Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Close Telnet Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

The eco PDU’s Main Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Securing the Power Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Le cordon d’alimentation principale de l’unité d’alimentation éco . . . . 86

Fixation des câbles d’alimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

IP Address Determination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

PE6108AVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

PE6208AVA / PE6208AVB / PE6208AVG / PE6208AVX. . . . . . . . . . 93

PE6208AVJ Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

PE8208AVB / PE8208AVG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

PE8208AVJ Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Administrator Login Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

eco PDU PE Series User Manual

ix

About This Manual

This User Manual is provided to help you get the most from your eco PDU

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the eco PDU system. Its purpose,

features and benefits are presented, and its front and back panel components

are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation.

Chapter 3, Basic Operation and First Time Setup, explains the

procedures that the Administrator employs to set up the eco PDU network

environment, and change the default username and password.

Chapter 4, Browser Operation, describes how to log in to the eco PDU with

an Internet browser, and explains the layout and components of the eco PDU’s

user interface.

Chapter 5, Telnet Access, describes how to connect to and access the eco

PDU’s using Telnet.

An Appendix, provides specifications and other technical information

regarding the eco PDU.

PE6108AV / PE6208AV / PE8208AV User Manual

x

Conventions

This manual uses the following conventions:

Product Information

For information about all NRGence products and how they can help you

connect without limits, visit NRGence on the Web or contact an NRGence

Authorized Reseller. Visit NRGence on the Web for a list of locations and

telephone numbers

 International – http://www.aten.com

 North America – http://www.aten-usa.com

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they

appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run

means to open the Start menu, and then select Run.

Indicates critical information.

1

Chapter 1

Introduction

Overview

ATEN has developed a new generation of green energy power distribution

units (PDUs) to effectively increase the efficiency of data center power usage

The NRGence PE6108AV / PE6208AV / PE8208AV eco PDUs are intelligent

PDUs that contain 8 AC outlets with a detachable front panel for convenient

rack mounting and are available in various IEC or NEMA socket

configurations.

They provide secure, centralized, intelligent, power management (power on,

off, cycle) of data center IT equipment (servers, storage systems, KVM

switches, network devices, serial data devices, etc.), as well as the ability to

monitor the center's health environment via sensors*. The basic characteristics

of each model are shown in the table on page 3.

NRGence eco PDUs offer remote power control combined with real-time

power measurement - allowing you to control and monitor the power status of

devices attached to the PDUs, either at the PDU and outlet level (PE8208AV)

or Bank level (PE6208AV), from practically any location via a TCP/IP

connection.

The power status of each outlet can be set individually, allowing users to switch

each device On/Off. The eco PDU also offers comprehensive power analysis

reports when used with the eco Sensors software which can separate

departments and locations, providing precise measurements of current,

voltage, power and watt-hour in a real-time display.

Installation and operation is fast and easy: plugging cables into their

appropriate ports and user-friendly browser-based configuration and

management is all that is entailed. Since the eco PDU firmware is upgradeable

over the Net, you can stay current with the latest functionality improvements

simply by downloading updates from our website as they become available.

NRGence eco PDU supports any 3rd party v3 SNMP Manager Software and

NRGence eco Sensors (eco PDU Manager Software). NRGence eco Sensors

provides you with an easy method for managing multiple devices, offering an

intuitive and user-friendly Graphical User Interface that allows you to

configure a PDU device and monitor power status of the equipment connected

to it.

PE6108AV / PE6208AV / PE8208AV User Manual

2

This series of ATEN eco PDUs have threshold alerts that can sound an alarm

and send SNMP trap or e-mail alerts when a threshold is exceeded. This feature

provides a faster response time to recover servers and other devices when the

outlets surpass thresholds set by you.

The PE6108AV / PE6208AV / PE8208AV is an excellent fit for any ATEN

VanCryst Pro A/V or VK Control System installation. Using our cross

platform solutions not only provide you with the best performance but also

utilize extra features which bring you more confidence and more power to

control.

With its advanced security features and ease of operation, the eco PDU is the

most convenient, most reliable, and most cost effective way to remotely

manage power access for multiple computer installations and allocate power

resources in the most efficient way possible.

Note: Sensors are optional accessories. A sensor-enabled installation is

required to generate a more complete energy-efficient data and chart.

Higher sensor installation density is helpful to generate more accurate

data. See Optional Accessories, page 5, for further information.

Chapter 1. Introduction

3

Features

Connections

 Space saving 1U rack mount design with rear mounting

 Detachable front panel for convenient rack mounting

 Support 10/100Mbit Ethernet Interface

 Support TCP/IP, UDP, HTTP, HTTPS, SSL, DHCP, SMTP, ARP, NTP,

DNS, Auto Sense, Ping, SNMP V1, V2, and V3, Telnet

 Support 2-level account/password security, IP/MAC filter, 128 bit SSL,

RADIUS

 Support: eco Sensors, Browser (IE, Firefox, Chrome, Safari)

 Additional functions available with ATEN VanCryst Pro A/V & VK

Control System installations

Metering

 Bank level power metering and monitoring (PE6208AV); or PDU and

outlet level power metering and monitoring (PE8208AV)

 Environment monitoring – supports external temperature/ temperature &

humidity sensors for rack temperature and humidity monitoring

 Current, voltage, power, power dissipation, temperature, and humidity

metering and threshold level setting

Outlet Switch Control

 Remote power outlet control (On/Off, Power Cycle) by individual outlets

and outlet groups

 Outlet group support at the PDU level

 Supports multiple power control methods – Wake on LAN, System After

AC Back, Kill the Power

 Power-On sequencing – users can set the power-on sequence and delay

time for each outlet to allow equipment to be powered on in the correct

order

 Local power on/off/reboot control via RS-232 port

 Proactive Overload Protection (POP) – automatically powers off outlets

when current overloads to protect connected devices

PE6108AV / PE6208AV / PE8208AV User Manual

4

Requirements

 Browsers accessing the eco PDU unit must support SSL 128 bit

encryption.

 For cold booting of attached computers, the computer's BIOS must

support Wake on LAN or System after AC Back.

 For Safe Shutdown:

 The computer must be running Windows (Windows 2000 or higher) or

Linux.

 The Safe Shutdown program (available by download from our website

or on the software CD included), must be installed and running on the

computer.

Chapter 1. Introduction

5

Optional Accessories

Sensors

Sensors are optional accessories. You can use the eco PDU unit without

sensors. However, if you want to have complete energy management of an

instrumented data center with the use of the eco PDU, you would need to use

eco Sensors software and install 4 sensors for each of the racks to generate a

complete energy-efficient data and chart. Higher sensor installation density is

helpful to generate more accurate data. 8-port models have 2 sensor ports. In

this case, Sensor 1 needs to be installed at the intake of the rack and sensor 2

needs to be placed at the exhaust of IT equipment of the rack. A sensor-enabled

installation is required to generate a more complete energy-efficient data and

chart. Higher sensor installation density is helpful to generate more accurate

data. Available sensors are show in the table, below:

Sensor Management

Sensors can be managed via the eco PDU’s built-in graphical user interface

(GUI) or with the NRGence eco Sensors software that can be downloaded from

the ATEN website. The download link can be found on the software CD

provided with the eco PDU package.

Cable Holders

Cable holders are optional accessories. For added safety, use ATEN Lok-U-

Plug cable holders to secure the cables from your attached devices in place on

the eco PDU unit. Use only the ATEN Lok-U-Plug cable holders that have

been specifically designed to work with the eco PDU. Using any other kind of

cable securing device could be highly dangerous.

Sensor Part Number

Temperature EA1140

Temperature / Humidity EA1240

Differential Pressure / Temperature EA1340

Part Number Description

2X-EA07 Lok-U-Plug Cable Holder (10 pcs)

2X-EA08 Lok-U-Plug Installation Tool (4 pcs)

PE6108AV / PE6208AV / PE8208AV User Manual

6

Components

PE6108AV / PE6208AV / PE8208AV Front View

No. Item Description

1 Port LED The Port LEDs provide status information about their

corresponding AC outlet ports. There is one pair of LEDs for each

port. The one on the left is the Local LED; the one on the right is

the Power LED:

 A Local LED lights GREEN to indicate that the device attached

to its corresponding port is capable of being controlled locally

via the Power Control Button. The Local Mode is enabled/

disabled with the Outlet Locked check box in the web GUI.

 A Power LED lights ORANGE to indicate that there is electricity

going to its corresponding outlet. The LED flashes under the

following conditions:

 If Modem Ring Resume is enabled (see Modem Ring

Resume*, page 30), an outlet still receives electricity even

when its corresponding computer has been powered OFF.

The Power LED blinks OFF, then ON for 8 seconds, then

OFF, then ON for 8 seconds, etc., to indicate this situation.

 When a power status change is pending, the LED flashes

until the change has taken place.

 If both LEDs flash it indicates that there is either an

overcurrent situation, or the relay has failed.

2 Current

LED

Lights to indicate that the Current (in amps) is being displayed on

the Status LED.

1

6

7

2 3

8 9

4

5

Chapter 1. Introduction

7

3 Status LED The current (in amps), IP address or Holiday Mode status displays

here. You can switch between the Current and IP status using the

Current / IP Switch (see item 7, below).

 When the Current status is displayed the Current LED (see

above) lights RED.

 When the IP status is selected, the unit’s IP address (two digits

of an octet at a time) will be shown, twice.

 When Holiday Mode is enabled the Status LED displays hd

(see Holiday Mode, page 41).

4 10/100

Mbps Data

LED

 The LED lights ORANGE to indicate 10 Mbps data transmission

speed.

 The LED lights GREEN to indicate 100 Mbps data transmission

speed.

5 Power LED Lights when the PDU is powered up and ready to operate.

6 Power

Control

Buttons

Each button (1 to 8), controls the power status of its corresponding

AC output port as follows:

 Under Local Mode, pressing and holding the button in for more

than 3 seconds switches the power to its corresponding port On

or Off.

 Pressing and holding button (1) in for more than 8 seconds

sequentially reboots all outlets.

 Pressing and holding button (8) in for more than 8 seconds

enables/disables Holiday Mode (see Holiday Mode, page 41).

7 Current / IP

Switch

Switches displaying the Current (in amps) – to displaying the IP

address on the Status LED.

 When pushed, the Status LED will display the unit’s IP address

(two digits of an octet at a time) twice and then switch back to

displaying the Current.

8 Reset

Switch

Press and release to reboot the PDU. Pressing and holding this

switch in for more than three seconds resets the PDU to its factory

default settings. This switch is recessed and must be pushed with

a thin object, such as the end of a paper clip, or a ballpoint pen.

9 Link LED Lights GREEN to indicate that a connection via the PDU's RJ-45

Ethernet port has been established. Flashes to indicate that data

is being transmitted.

No. Item Description

PE6108AV / PE6208AV / PE8208AV User Manual

8

PE6108AV / PE6208AV / PE8208AV Rear View (exclude PE6208AVX)

PE6208AVG rear view is used as the example above.

No. Item Description

1 Reset

Switch

Press and release to reboot the PDU. This switch is recessed and

must be pushed with a thin object, such as the end of a paper clip,

or a ballpoint pen.

2 Sensor

LEDs

Two Sensor LEDs light GREEN when a sensor is connected to the

respective sensor port.

3 Sensor

Ports

External sensors plug into these two RJ-11 ports.

4 Power

Sockets

The power cables that connect to the computers plug in here.

5 Power

Switch

This standard rocker switch powers the PE6108AV / PE6208AV /

PE8208AV On and Off.

6 Power

Socket

The power cable from the AC source plugs in here.

7 RS-232

Port

This port can be used to attach to a computer for local power on/

off/reboot control.

8 LAN Port The Cat 5e cable that connects the PE6108AV / PE6208AV /

PE8208AV to the Internet plugs in here.

432

7

8

561

Chapter 1. Introduction

9

PE6208AVX Rear View

No. Item Description

1 Reset

Switch

Press and release to reboot the PDU. This switch is recessed and

must be pushed with a thin object, such as the end of a paper clip,

or a ballpoint pen.

2 Sensor

LEDs

Two Sensor LEDs light GREEN when a sensor is connected to the

respective sensor port.

3 Sensor

Ports

External sensors plug into these two RJ-11 ports.

4 Power

Outlet

Cable

Glands

Connect power of computers here. Please refer to Power Cord

Installation (PE6208AVX) on page 15.

5 Power Inlet

Cable

Gland

Connect AC source here. Please refer to Power Cord Installation

(PE6208AVX) on page 15.

6 Power

Switch

This standard rocker switch powers the PE6208AVX On and Off.

7 RS-232

Port

This port can be used to attach to a computer for local power on/

off/reboot control.

8 LAN Port The Cat 5e cable that connects the PE6208AVX to the Internet

plugs in here.

432

7

8

561

PE6108AV / PE6208AV / PE8208AV User Manual

10

This Page Intentionally Left Blank

La page charge ...

ATEN PE6108AV Manuel utilisateur

Ce manuel convient également à

ATEN PE6108AV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents