Cembre B70M-P36E Manuel utilisateur

1

BATTERY OPERATED HYDRAULIC PUMP

POMPE HYDRAULIQUE SUR BATTERIE

HYDRAULISCHE AKKUPUMPE

BOMBA HIDRÁULICA A BATERÍA

POMPA OLEODINAMICA A BATTERIA

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

OPERATION AND MAINTENANCE MANUAL ....................................6

NOTICE D’UTILISATION ET ENTRETIEN ........................................... 21

BEDIENUNGSANLEITUNG ................................................................... 36

MANUAL DE USO Y MANTENIMIENTO ........................................... 51

MANUALE D’USO E MANUTENZIONE ............................................. 66

19 M 085

B70M-P36 B70M-P36A B70M-P36E B70M-P36T

B85M-P36

2

FIG. / BILD 2

B

H

A

C

E

F

D

G

FIG. / BILD 1

1

9

10

12

7

3

2

4

1

11

6

8

5

3

FIG. / BILD 5

CLICK

FIG. / BILD 3

10

6

9

20

21

22

5

15

14

Battery - Batterie - Akku - Batería - Batteria

CB3662L

ERCH

16

FIG. / BILD 4

G

4

OIL

2

Max. oil level

Niveau maxi. d’huile

Max. Ölstand

Nivel de aceite máx.

Livello max. olio

FIG. / BILD 6

FIG. / BILD 7

FIG. / BILD 8

161 (6.3)

327 (12.9)

405 (15.9)

mm (inch)

5

– Before using the pump, carefully read the instructions in this manual.

– Avant d'utiliser la pompe, lire attentivement les instructions de cette notice.

– Vor Inbetriebnahme unbedingt die Bedienungsanleitung durchlesen.

– Antes de utilizar la bomba, leer atentamente las instrucciones en este manual.

– Prima di utilizzare la pompa, leggere attentamente le istruzioni riportate in

questo manuale.

– Always wear safety glasses and gloves when operating this tool.

– Porter toujours les lunettes de protection et les gants de travail.

– Immer mit Schutzbrille und Handschuhen bedienen.

– Trabajar siempre con las gafas de proteccion y guantes de seguridad.

– Operare sempre con occhiali di protezione e guanti da lavoro.

WARNING SYMBOLS - SYMBOLES D'AVERTISSEMENT - WARNSYMBOLE -

SÍMBOLOS DE ADVERTENCIA - SIMBOLI DI AVVERTENZA

– User information (Directives 2011/65/UE and 2012/19/UE),

see page 82.

– Information pour les utilisateurs (Directives 2011/65/UE et 2012/19/UE)

voir page 82.

– Information für den Benutzer (Richtlinien 2011/65/UE und 2012/19/UE)

siehe Seite 82.

– Informe para los usuarios (Directivas 2011/65/UE y 2012/19/UE)

vease página 82.

– Informazione agli utenti (Direttive 2011/65/UE and 2012/19/UE)

riferirsi a pagina 82.

Pump - Pompe - Pumpe - Bomba - Pompa

6

ENGLISH

Hydraulic pumps manufactured by Cembre S.p.A. are developed for use with hydraulic

heads. According to this specific use, they do not need and are not equipped with an oil

non-return safety system.

For this reason, use in applications different from those intended (for example with hy-

draulic jacks, lifting systems or similar) can be dangerous for the operator.

Cembre S.p.A. does not accept any liability arising from the use of its hydraulics pumps

for applications different from those listed in its catalogues or other documentation.

Do not use the pump for purposes other than those intended by Cembre S.p.A..

The operator should concentrate on the work being performed and be careful to maintain

a balanced working position.

Avoid dirty surfaces: dust and sand are a danger to any Electro-hydraulic equipment.

The flexible hydraulic hose supplied should always be used to connect the hydraulic head

to the pump. The hydraulic head should never be directly connected to the pump.

Never connect to a pump hydraulic heads that still contain oil, namely with the ram not

fully retracted; excess oil could cause the pump to malfunction.

Before disconnecting the flexible hose, check that the ram of the head is completely retracted,

in order to ensure that a sufficient quantity of oil is available for subsequent operations.

High pressure flexible hoses are subject to a natural ageing process which can result in

a reduction in performance potentially affecting safety of the operator. As a result their

life span is limited.

In order to ensure safe use of their units, Cembre recommends replacing the hose within

10 years from the date printed on the fittings.

Keep the pump and flexible hose away from naked flames and sources of heat above 70°C.

Before using the pump, check that the flexible hose and couplings are not damaged.

The factory fitted guards must be in place at each end of the flexible hose.

Do not touch the flexible hose when under pressure.

When using the pump, the flexible hose must be uncoiled and laid out straight.

The pump is unsuitable for continuous use and should be allowed to cool down follow-

ing uninterrupted, successive crimping operations; for instance, having exhausted a fully

charged battery in one session, delay battery replacement for a few minutes.

WARNING

7

Safety instructions for batteries:

– Protect battery from water and moisture!

– Do not expose batteries to naked ﬂ ames!

– Do not use faulty or deformed batteries!

– Do not open batteries!

– Do not touch or short circuit battery contacts!

– A slightly acidic, ﬂ ammable ﬂ uid may leak from defective Li-Ion

batteries!

– If battery ﬂ uid leaks out and comes into contact with your skin,

rinse immediately with plenty of water. If battery ﬂ uid leaks out

and comes into contact with your eyes, wash them with clean

water and seek medical attention immediately!

– At the end of their life, always recycle batteries.

– Never discard batteries with domestic waste. They must be sent

to appropriate collection centres for disposal.

– If the pump is defective, remove the battery from the pump.

– Remove the battery from the pump being transported.

– Transport of Li-Ion battery packs:

The shipping of Li-Ion battery pack is subject to laws related to the carriage of hazardous goods

(UN 3480 and UN 3481).

Familiarise yourself with current regulations concerning shipment of Li-Ion battery packs.

Only send the battery pack if the housing is intact and no ﬂ uid is leaking.

Remove the battery pack from the pump being transported.

Prevent the contacts from short-circuiting (e.g. by protecting them with adhesive tape).

Compliance of use

– The device is a portable battery powered hydraulic pump, it can be connected to hydraulic

heads for compression, cutting and punching and other speciﬁ c uses produced by Cembre

Any other use, or use deemed to be outside of the speciﬁ cation of the device shall be regarded

as improper use. In these instances the manufacturer/supplier shall not be liable for any damage

resulting from improper use and the user agrees to bear all risk.

– The device is manufactured in accordance with current technological standards and recognized

safety rules. However, danger to life and limb of the user or third parties/or damage to the

device and other tangible assets can arise during use.

– The device may only be used for its intended purpose and if in perfect working order, it must

be used with appropriate consideration given to the safety and danger warning messages

stated in the operating manual.

– Usage of the device for its intended purpose also incorporates compliance with the operating

manual, including the manufacturer‘s maintenance recommendations and speciﬁ cations.

8

(1)

Directive 2006/42/EC, annexe 1, point 1.7.4.2 letter u

L

pA

= weighted continuous acoustic pressure level equivalent.

L

pCPeak

= maximum value of the weighted acoustic displacement pressure at the work place.

L

WA

= acoustic power level emitted by the machine.

(2)

Directive 2006/42/EC, annexe 1, point 2.2.1.1

Weighted root mean square in frequency of the acceleration the upper limbs are exposed to for each biodynamic

reference axis. Tests carried out in compliance with the indications contained in EN ISO 5349-1/2 Standard, and

under operating conditions much more severe than those normally found.

1. GENER AL CHARACTERISTICS

B70M-P36 B85M-P36

Operating pressure

bar (psi) 700 (10153) 850 (12328)

Oil supply l / min (US gpm) 0,67 (0.19) 0,57 (0.16)

Oil reservoir capacity

cm

3

(cu. in.)

1100 (67.1)

Degree of protection IP 44M (EN 60529)

Dimensions Ref. to Fig. 8 page 4

Weight with battery kg (lbs) 10 (22)

Motor V

36

Operating temperature °C (°F) -20 to +50 (+4 to +122)

Recommended oil ENI ARNICA ISO 22 or equivalents

Safety maximum pressure valve

Rechargeable battery type CB3662L Li-Ion

Voltage / Capacity V / Ah (Wh) 36 / 6.2 (223,2)

Weight kg (lbs) 1,6 (3.5)

Acoustic noise

(1)

dB L

pA

69,8 (A) L

pCPeak

93 (C) L

WA

83,4 (A)

Vibrations

(2)

m/s

2

0,652

B70M-P36

B85M-P36

B70M-P36E B70M-P36T B70M-P36A

Battery charger type ASC-ULTRA-

EU

ASC-ULTRA-

UK

ASC-ULTRA-

AUS/NZ

ASC-ULTRA-

USA/CAN

Input

Power

V / Hz

W

220 - 240 / 50 - 60

290

115 / 60

290

Output V

/ A 14,4 - 36 / 6,5 max.

Weight kg 0,97

ENGLISH

9

ENGLISH

2. DESCRIPTION OF THE COMPONENTS

The part reference includes the following (See Fig. 1):

(

A) FLEXIBLE HOSE: length 3 m (9.75 ft) specific for high pressure; provided with automatic quick

couplings; enables connection of the hydraulic head to the pump

(B)

RUCKSACK

: made from sturdy fabric, allows users to store and transport the pump and acces-

sories.

(C)

SHOULDER STRAP: allows users to easily transport and comfortably carry the pump during

all work phases; to be connected to the rings (1).

(D) ERCH REMOTE CONTROLLER: ergonomically designed with a comfortable grip even while

wearing work gloves. provided with a 3 m connection cable, it allows users to control the

pump by two push-buttons:

- GREEN button to activate the pump with a pulse (starting from the display oﬀ ) and to activate

the pump motor.

- RED button to oil discharge: for returning the oil to the pump tank at any time.

(E)

USB CABLE

(Ref. to § 6)

(F)

AS

C-ULTRA BATTERY FAST CHARGER (diﬀ ers depending on the pump version): for recharging the

batteries supplied; has “AIR COOLED” charging technology and a processor for managing

charging cycles.

To use, carefully follow the instructions in the battery charger user manual.

(G)

CB3662L RECHARGEABLE BATTERY:

36 V - 6.2 Ah high capacity Lithium Ion battery.

The battery is equipped with LED indicators that indicate the

remaining battery life at any time by pressing

the adjacent button (C):

4 LEDs illuminated: fully charged

2 LEDs illuminated: 50 % capacity

1 LED ﬂ ashing: minimum charge, the battery is

almost depleted and needs to be charged.

With the battery inserted into the tool, the remain-

ing battery life can also be checked on the display,

via touch button selection (Ref. to § 4).

The screen shown alongside indicates that the battery voltage has

dropped below a minimum safety threshold; under these conditions

the tool will not start, and it is necessary to recharge or replace the battery.

Batteries are supplied with a charge ≤ 30%. To maximise energy level, it is necessary to

fully recharge them before use. Charge the battery by following the instructions pro-

vided in the battery charger manual, approximately 50-60 minutes are required to charge a

fully depleted battery with ASC ULTRA fast charger. Only use the battery charger supplied with

the pump.

C

max.

BATTERY

Ï

Ð

min.

BATTERY

Ï

Ð

10

ENGLISH

The electronics protect the battery from any damage caused by complete depletion.

A completely charged battery provides 100% of its

energy between -20 and + 50 °C (- 4 and +122 °F).

Continuous overload causes deactivation due to overheating. In such a case, allow the battery

to cool down; if the battery feels hot to the touch, it can be cooled down more quickly by inser-

ting it into the relevant “AIR COOLED” battery charger.

Optimal battery storage temperature is between 10 and 30 °C(50 and 86 °F).

Removal / Insertion of the battery (Ref. to Fig. 3)

Position the pump as shown in Fig. 3.

Press button (5) and open the cover (6).

Removal

:

Press button (15) and pull the battery ﬁ rmly to remove it from its seat. If necessary, use the

strap (14) to facilitate extraction.

Insertion:

Insert the battery into the slots until it locks into place.

Close the cover (6) ensuring that it is fully locked with the button (5).

Before inserting the battery, move the strap(14) so that it does not hinder the operation.

The strap must be placed as shown in ﬁ gure 3 after inserting the battery.

(H) PORTABLE HYDRAULIC PUMP: motor-driven at 36V DC current, battery powered for autono-

mous use. Provided with a pressure transmitter that ensures precision and repeatability of the

work cycles and a maximum pressure valve to ensure maximum operator safety. The memory

card integrated into the pump allows the storage of the data relating to operating cycles, errors

and malfunctions are then displayed on a PC using speciﬁ c software.

Main components (Ref. to Fig. 2):

1 STRAP FASTENING RING

2 OIL FILLER CAP

3 OLED DISPLAY, switches on automatically when the operating button is pressed, and oﬀ

after 5 minutes of non-operation).

4 CAPACITIVE TOUCH BUTTON (for menu selection allows selection of various screens (Ref. to §

4) only when the display is on.

Do not apply pressure to or stab at the touch button, a light touch using a bare ﬁ nger is

suﬃ cient. The command pulse is sent when the ﬁ nger releases the button.

The capacitive menu selection button may not work if touched using objects or when wearing

gloves, therefore always operate it using a bare ﬁ nger.

11

ENGLISH

5 BUTTON TO OPEN THE BATTERY COMPARTMENT

6 BATTERY COMPARTMENT COVER

7 MECHANICAL PRESSURE RELEASE

8 BRIGHT CEMBRE LOGO, switches on automatically when the operating button is pressed, and

oﬀ after 5 minutes of non-operation. It allows the operator to have a visual feedback on the

pump status. It can ﬂ ash or produce a ﬁ xed light with various colours depending on the mes-

sage emitted. The following table summarises the possible cases that can be found:

Lighting Meaning Note

steady

BLUE

Pump powered and in stand-by

mode, ready to use.

Stays on until the "sleep" function is ac-

tivated. After 5 minutes of inactivity the

pump switches oﬀ automatically.

pulsating

BLUE

Motor running and work cycle

in progress.

Flashes during the entire work cycle.

steady

GREEN

Correct completion of the

CRIMPING cycle carried out.

Lights up at the end of the cycle together

with the "OK" message on the display.

ﬂ ashing

RED

Incorrect completion of the

CRIMPING cycle carried out.

Lights up together with the "ERROR" mes-

sage on the display and an intermittent

audible alarm (see § 4.6 for further

details).

steady

ORANGE

Scheduled maintenance re-

quired.

Stays on until the "sleep" function is acti-

vated. It reappears each time the pump is

switched on until the scheduled mainte-

nance has been carried out and the cycles

have been simultaneously reset to zero.

pulsating

ORANGE

Motor running and work cycle

in progress, scheduled mainte-

nance required.

Flashes during the entire work cycle.

ﬂ ashing

YELLOW

Fault in progress. Stays on until the anomaly has been

resolved, together with an indication on

the display and an audible alarm (see §

4.6 and 4.7 for further details).

9 QUICK COUPLING (automatic locking, ﬁ tted with a fast-acting safety ring nut to eliminate

any risk of accidental disconnection)

10 CONNECTOR with cap, suitable to connect the remote controller.

12

ENGLISH

11 CONTROL BUTTON ON THE PUMP: rocker type switch, allows:

To switch on the pump (push forwards for actuation, starting with display oﬀ ).

To control the pump (push forwards for actuation of the motor and backwards for oil re-

lease).

To control the pump from the button (11), it is necessary to deactivate the ERCH push-

button panel via the display (see § 4.4 for further details).

When a crimping head is used, press and hold the operating button (1) until the motor

stops automatically.

AUTO POWER-OFF: the pump switches oﬀ automatically after a period of inactivity

of 5 minutes; to reactivate the pump, press the button again.

12 TRANSPORT HANDGRIP

3. INSTRUCTIONS FOR USE

3.1) Preparation

The pump can be easily carried using either the main handle (10) or the shoulder strap attached

to the two rings (1) (Ref. to Fig. 2).

Position the pump on a ﬂ at surface. There are two stable work positions recommended (see Fig. 6):

- vertical, resting on its base.

- horizontal, resting on its back where moulded ribs improve ﬁ rmness and stability

Should it be necessary however, the pump’s hermetically sealed hydraulic circuit allows it to

operate in any position.

Before starting any work, check the battery charge and recharge it if necessary following

the instructions in the battery charger user manual.

3.2) Connecting the remote hand controller (Ref. to Fig. 4)

Remove "REMOTE CONTROLLER" protective cap, connect the remote hand controller to the

socket (10) (see Fig. 4): tighten the plug (16) by turning the bezel clockwise until it locks.

3.3) Connecting the ﬂ exible hose (Ref. to Fig. 5)

Fully unravel the flexible hose.

Connect the male coupler (20) of the flexible hose to the female coupler (9) of the pump then

pull towards the hose and turn the safety ring (G) to eliminate any risk of accidental disconnec-

tion.

Connect the female coupler (21) of the flexible hose to the male coupler (22) of the hydraulic

head to be used then pull towards the hose and turn the safety ring (G) to eliminate any

risk of accidental disconnection.

Before using the pump always check the integrity of the ﬂ exible hose and the quick couplers

making sure there are no abrasions, cuts, deformations or swellings.

5 min.

13

ENGLISH

3.4) Operation

Activate the pump by pushing the green button on the control handle or the button on the

pump (if enabled), the display (3) and the Cembre logo (8) turn-on.

Through the display, the operator can view and change some of the pump’s setting using the

touch button (4) (Ref. to § 4). The display shows the operating mode and oil release settings of

the pump at each start-up (starting with the display switched oﬀ ) or upon insertion of the bat-

tery.

Examples:

IMPORTANT: Prior to using the pump, always check the operating mode set is the correct

one for the type of job to be carried out, choosing between:

CRIMPING – CUTTING – PUNCHING (Ref. to § 4.2).

The factory settings are:

- operating mode: CRIMPING (Ref. to § 4.2 to choose another operating mode).

- oil release type: SMART (Ref. to § 4.3 for further details).

- control: ERCH ON (by remote controller, ref. to § 4.4 for further details).

Proceed with the job by operating as follows:

CRIMPING OPERATION

Press the start button: this activates the motor of the pump that feeds the

hydraulic head connected to it, pressurising the oil.

Once the minimum set pressure (P

n

) is reached the pump will be switched

oﬀ automatically, the display will brieﬂ y show the maximum pressure reached

(P

p

) followed by “OK” and the Cembre logo will light up GREEN to conﬁ rm the

correct operation.

Releasing the start button before the automatic stopping of the motor will

cause the pump to stop, keeping the oil pressure stable (P

p

) at the value

reached at that moment. To complete the operation press the start button

once more until the motor stops automatically.

The display "ERROR" combined with a beep and and the RED ﬂ ashing

of the Cembre logo, indicates an incorrect crimping procedure; the oil

return phase occurred too early without waiting for the motor to be automati-

cally switched oﬀ and therefore the minimum set pressure was not reached. This

error appears when the pressure release button has been operated and the

pump has already reached a pressure > 100 bar. Repeat the crimping cycle by

holding down the start button until the motor is automatically switched oﬀ .

Pn = 700 bar

OK

Pn = 700 bar

P

p = 701 bar

Pn = 700 bar

P

= 0 bar

ERROR

Ï

Ð

14

When a crimping head is used, press and hold the operating button until the motor stops auto-

matically.

At the end of the cycle, proceed with the phase of returning the oil to the pump reservoir (Ref.

to § 3.5 for further details).

CUTTING OPERATION

Press the start button: this activates the motor of the pump that feeds the

hydraulic head connected to it, pressurising the oil. Keep the button pressed

until the cutting operation is complete. At the end of the cycle the display

will show the maximum pressure reached (P

p

).

At the end of the cycle, proceed with the phase of returning the oil to the

pump reservoir (Ref. to § 3.5 for further details).

PUNCHING OPERATION

Press the start button: this activates the motor of the pump that feeds the

hydraulic head connected to it, pressurising the oil. Keep the button pressed

until the punching operation is complete. At the end of the cycle the display

will show the maximum pressure reached (P

p

).

At the end of the cycle, proceed with the phase of returning the oil to the

pump reservoir (Ref. to § 3.5 for further details).

3.5) Oil release

The phase of returning the oil to the pump reservoir, or rather to the re-entry of the ram of the

connected hydraulic head, may be carried out in two diﬀ erent ways depending on the release

mode set (Ref. to § 4.3 for further details):

With the ERCH remote controller:

- smart mode: release the GREEN start button (following automatic shut-oﬀ of the motor).

- manual mode: press the RED release button.

With the rocker switch (11) on the pump (only if the remote controller

is deactivated):

- smart mode: release the control button at the end of the cycle.

- manual mode: push the control button backwards.

If required, by pressing hard on the mechanical pressure

release button (7), the oil will return to the reservoir whatever

the status of the battery.

7

ENGLISH

Pp = 547 bar

P = 0 bar

Pp = 325 bar

P = 0 bar

15

ENGLISH

4. NAVIGATION MENU

The navigation menu is shown on the display (3) o. By touching

the button (4) it is possible to browse the

menu via the various screens.

4.1) Structure of the "main menu"

Pn: Operating/minimum set pressure, expressed in bar.

P: Peak pressure reached, expressed in bar.

Pn: Operating/minimum set pressure, expressed in psi.

P: Peak pressure reached, expressed in psi.

Operating mode set.

(Ref. to § 4.2 for further details).

Release mode set .

(Ref. to § 4.3 for further details).

Disabling / Enabling the remote controller

(Ref. to § 4.4 for further details)

Battery charge level.

No. of cycles performed.

No. of cycles before scheduled recommended maintenance.

Cembre logo, pump model.

Pump serial no.

Actual temperature (°C) of the pump motor.

Return to original factory settings.

Firmware version (Ref. to § 4.5 for further details).

Stand-by

10

-29990

3

BATTERY

RESET

SW: S1J56100

Pn = 700 bar

P

= 0 bar

Pn = 10153 psi

max 90°

60°

* 1

* 2

3

4

5

* 6

* 7

* 8

* 9

10

11

P = 0 psi

ERCH OFF

ERCH ON

B70MP

19AB863

4

3

16

ENGLISH

(*) Screens 1-2-6-7-8-9 can be set as the “main screen” which is shown

on the display at every use of the pump; to do this, when the pre-

selected screen is displayed, hold the ﬁ nger on the button (4) until a

conﬁ rmation “beep” is heard.

4.2) Choosing the "operating mode"

The “operating mode” allows the user to set the pump depending on the type of hydraulic head

connected; this enables the optimisation of the job cycle and charging of the battery.

It is possible to choose between three diﬀ erent operating modes:

CRIMPING CUTTING PUNCHING

Operating

mode

Associated

pictogram

Function

CRIMPING

factory setting

Speciﬁ cally for using the pump with hydraulic heads for crim-

ping of electrical connectors.

CUTTING

Speciﬁ cally for using the pump with hydraulic heads for cutting

electrical conductors and steel ropes.

PUNCHING

Speciﬁ cally for using the pump with frame type hole punching

hydraulic heads or piercing hydraulic heads.

To change the “operating mode” proceed as follows:

- Select screen 3 from the “main menu” (Ref. to § 4.1).

- Hold the finger on the button (4) until a confirmation “beep” is heard, the choice made is shown

by filling of the related pictogram.

BEEP

2

BEEP

2

BEEP

2

17

ENGLISH

4.3) Choosing the "release mode"

The phase of discharging the oil into the pump’s tank can be carried out in two diﬀ erent ways,

depending on the mode set in the menu:

Release

mode

Associated

pictogram

Function

SMART

factory setting

By releasing the start button the oil is returned in full to the pump

reservoir only following automatic shut-oﬀ of the motor. During

the return phase, pressing the buttons enables the head ram stroke

to be interrupted at any point so as to be able to restart from this

position in the next work phase, thus saving time and energy.

MANUAL

To return the oil to the pump reservoir it is necessary to press and

hold the release button.

During the return phase, by releasing the button it is possible for

head ram stroke to be interrupted at any point so as to be able

to restart from this position in the next work phase, thus saving

time and energy.

To change the "release mode" proceed as follows:

- Select screen 4 from the “main menu” (Ref. to § 4.1).

- Hold the finger on the button (4) until a confirmation “beep” is heard, the choice made is shown

by positioning of the cursor under the pictogram.

4.4) Choosing the "control mode"

The pump can be controlled during all working phases via the remote controller or via the button

(11) on the pump. Control mode selection is set in the menu:

Control

mode

Associated

pictogram

Function

REMOTE

CONTROLLER

factory setting

ERCH ON

The pump is controlled only by the remote controller, the push-

button on the pump is disabled.

BUTTON

ON THE PUMP

ERCH OFF

The remote controller is disabled, the pump is controlled only

via the push-button on the pump.

NOTE: After the pump is automatically turned oﬀ or the

battery is removed, the mode returns to the factory setting:

ERCH ON

To change the "release mode" proceed as follows:

- Select screen 5 from the “main menu” (Ref. to § 4.1).

- Hold the finger on the button (4) until a confirmation “beep” is heard.

18

ENGLISH

4.5) Return to original factory settings / ﬁ rmware version

Select screen 10 from the “main menu” (Ref. to § 4.1), to return the pump to its factory setting hold

the finger on the button (4) until a confirmation “beep” is heard.

The RESET screen also shows the ﬁ rmware version of the control board.

4.6) Errors/Malfunctions

These appear on the display during operation, combined with a beep to notify the operator of

procedural or operational errors. They are accompanied by an audible signal and the Cembre

logo (8) lighting up yellow.

Message Error description

Solution

ERROR

Ï

Ð

In CRIMPING mode, a 100 bar pres-

sure has been reached or exceeded

but the oil discharge has been acti-

vated before waiting for the motor

to be automatically switched oﬀ .

Repeat the work cycle, keeping the start but-

ton pressed down until the motor switches oﬀ

automatically.

The pump has been started with-

out the ﬂ exible hose connected or

the ﬂ e-xible hose is not correctly

connected.

Press the release button, connect the ﬂ exible

hose or check the correct connection to the

pump.

NTC

FAULT

Interruption of the signal from the

NTC temperature probe of the

battery.

Replace the battery. If the problem persists,

please contact Cembre.

001

Ï

Ð

Abnormal power consumption of

the motor.

The pump stops.

Wait for the display to turn oﬀ (60 sec.) or remove

and re-insert the battery, then re-start the

pump, if the problem persists, please contact

Cembre.

002

Ï

Ð

Output voltage of the pressure trans-

mitter is out of the pre-set range.

The pump stops and doesn't re-start.

Remove and re-insert the battery, if the prob-

lem persists, please contact Cembre.

003

Ï

Ð

Failure to reach the set pressure

within 120 sec. of continuous opera-

tion of the pump.

Repeat the work cycle; if the problem persists,

please contact Cembre.

004

Ï

Ð

Overcharging of the battery with

protection tripping.

The pump stops.

Wait for the display to turn oﬀ (60 sec.) or re-

move and re-insert the battery, then re-start the

pump. if the problem persists, please contact

Cembre.

Errors 00.. are displayed for about 30 seconds before being reset, but will display repeat-

edly in the event of permanent anomalies.

RESET

SW: S1J56100

19

4.7) Alarms/Warning

These appear on the display during operation, inform the operator on the state of the pump.

They are accompanied by an audible signal and the Cembre logo (8) lighting up yellow or orange.

Message Meaning Description

BATTERY

Ï

Ð

BATTERY

LOW

Replace or recharge the battery.

NOTE: when the battery voltage falls below a minimum safety

threshold, the pump will not start, although it is still possible

to end the work cycle in progress.

BATTERY

Ï



Ð

BATTERY

TEMPERATURE

HIGH

Remove the battery and wait until it cools down.

In order to cool it quicker, it is possible to insert it into the sup-

plied battery charger supplied, thus making use of the speciﬁ c

“AIR COOLED” function.

max 90°

90°

MOTOR-PUMP

TEMPERATURE

HIGH

The maximum permitted operating temperature of 90 °C (194

°F) is reached.

The pump stops; in this instance wait for it to cool.

Only when the permitted working temperature is reached will

it be possible to re-use the pump.

INSUFFICIENT

OIL

This appears when the pressure of the hydraulic circuit doesn't

increase but remains near to zero for a duration of 30 consecu-

tive seconds.

Check the oil level and if necessary reﬁ ll (Ref. to § 5.4).

30001

3

Ï

Ð

REQUEST

MAINTENANCE

No. of cycles to maintenance reached; the pump continues to

work however, it is recommended that it is sent to Cembre for

a complete overhaul (Ref. to § 7).

This screen is associated with the orange color of the logo.

5. MAINTENANCE

The pump is robust, completely sealed, and requires very little daily maintenance. Compliance

with the following points, should help to maintain its optimum performance:

High pressure flexible hoses are subject to a natural ageing process which can result

in a reduction in performance potentially affecting safety of the operator. As a result

their life span is limited.

In order to ensure safe use of their units, Cembre recommends replacing the hose within 10

years from the date printed on the fittings.

5.1) Thorough cleaning

Dust, sand and dirt are a danger for any hydraulic device.

Every day, after use, the pump and accessoires must be wiped with a clean cloth taking care to

remove any residue. Do not use Hydrocarbons to clean the rubber parts.

After use, protect the couplers of the pump, hose and hydraulic head with their protective

caps to prevent contamination.

ENGLISH

20

ENGLISH

5.2) Rucksack

To protect the pump from accidental damage and dust, it should be stored with its accessories in

the special rucksack provided and sealed well.

Rucksack type CVB-037: Size 540x270xh550 mm (21.2x10.6x21.6 inches), weight 3,2 kg (7 lbs).

5.3) Storage

Once the job has been completed always completely release the pressure of the oil by holding

down the release button; ensure that the ram of the connected hydraulic head is completely

retracted before disconnecting the head.

Remove the battery from the pump.

Disconnect the remote controller.

Disconnect the ﬂ exible hose; avoid it becoming folded with narrow bends or knots that may

compromise its integrity.

Store the pump and accessories in the rucksack in a dry place.

5.4) Topping up the oil (Ref. to Fig. 7)

Periodically check, at least every 6 months, the oil level in the pump and top up if necessary:

Position the pump on its base on a ﬂ at surface.

Completely discharge the oil pressure by pushing the pressure release button (7).

Unscrew the ﬁ ller cap (2).

By using a funnel, top up very slowly to completely ﬁ ll the oil reservoir to the maximum level.

When the operation is ﬁ nished replace the cap (2).

Always use clean recommended oil, see § 1.

Do not use old or recycled oil. Do not use hydraulic brake ﬂ uid.

Ensure that used oil is disposed of in accordance with current legislation.

6. CONNECTION TO COMPUTER (Smartool technology)

Extract the battery and connect the supplied USB cable to the connector (30) inside the battery

seat then to the USB port of the PC (Ref. to Fig. 9).

The memory card integrated in the tool records operating data for transfer via the USB cable supplied.

To view and manage this data, go to www.cembre.com and register in the dedicated area, then

download the free Cembre software CEM_SWBT01.

Keeping the Firmware of the tool updated, via free of charge download from here, will optimise

the tool's performance.

La page charge ...

Cembre B70M-P36E Manuel utilisateur

Ce manuel convient également à

Cembre B70M-P36E Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents