PowerStroke PS141913 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire

Ce manuel convient également à

OPERATOR’S MANUAL
MANUEL DUTILISATION / MANUAL DEL OPERADOR
ELECTRIC PRESSURE WASHER
LAVEUSE À PRESSION ÉLECTRIQUE
LAVADORA DE PRESIÓN A ELÉCTRICA
PS141913/PS141955
CUSTOMER SERVICE
SERVICE À LA CLIENTÈLE / SERVICIO AL CLIENTE
USA: 1-877-617-3501
Monday – Friday 8am-8pm ET/Saturday and Sunday 9am-6pm ET
Translation Available in Over 200 Languages
CANADA : 1-877-617-3501
Lundi au vendredi de 8 h à 20 h HNE/Samedi et dimanche de 9 h à 18 h HNE
Traduction disponible dans plus de 200 langues
Mexico: 01 800 843 1111
De lunes a viernes, de 8 a. m. a 8 p. m. (hora del este)/Sábados y domingos, de
9 a. m. a 6 p. m. (hora del este)
Traducción disponible en más de 200 idiomas
www.powerstroketools.com
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
WARNING: To reduce the risk of
injury, the user must read and understand
the operator’s manual before using this
product.
TABLE OF CONTENTS
Important Safety Instructions ...............2
Specific Safety Rules ........................3-4
Symbols ...............................................5
Electrical ..............................................6
Features ...............................................7
Assembly ..........................................7-9
Operation ......................................10-13
Maintenance .................................13-14
Troubleshooting .................................15
Parts Ordering and Service ...Back Page
AVERTISSEMENT : Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’utiliser ce produit.
TABLE DES MATIÈRES
Instructions importantes
concernant la sécurité..........................2
Règles de sécurité particulières ........3-4
Symboles ..........................................5-6
Caractéristiques électriques .............6-7
Caractéristiques ................................... 8
Assemblage ....................................8-10
Utilisation ......................................10-14
Entretien ........................................15-16
Dépannage ....................................16-17
Commande de pièces et
réparation ........................... Page arrière
ADVERTENCIA: Para reducir el
riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
ÍNDICE DE CONTENIDO
Instrucciones de seguridad
importantes .......................................... 2
Reglas de seguridad específicas ......3-4
Símbolos ...........................................5-6
Aspectos eléctricos ..........................6-7
Características .....................................8
Armado ...........................................8-10
Funcionamiento ............................11-14
Mantenimiento ..............................15-16
Solución de problemas .................16-17
Pedidos de piezas y
servicio ............................ Pág. posterior
SAVE THIS MANUAL FOR
FUTURE REFERENCE
To register your POWERSTROKE product, please visit:
http://register.powerstroketools.com/
Pour enregistrer votre produit de POWERSTROKE,
veuillez visiter : http://register.powerstroketools.com/
Para registrar su producto de POWERSTROKE, por favor
visita: http://register.powerstroketools.com/
ii
Fig. 1 Fig. 2
A - Test button (essayer le bouton, botón de
prueba)
B - Reset button (bouton « reset », botón de
reajuste)
A
B
Fig. 3
A - Start button (bouton de démarrage, botón de
arranque)
B - Nozzle storage (rangement de buse,
almacenamiento para boquilla)
C - Spray wand (lance de pulvérisation, tubo
rociado)
D - Motor housing (boîtier de moteur, alojamiento
del motor)
A
C
H
K
C
F
A
B
B
E
G
E - Soap tank (réservoir de savon, tanque de
jabón)
F - Trigger with lock-out (gâchette avec
verrouillage, gatillo con seguro)
G - Power cord storage brackets (supports de
rangement pour cordon d’alimentation,
soportes para almacenamiento del cordón
eléctrico)
A - Pressure washer power cord (cordon
d’alimentation de la laveuse à pression,
cordón de corriente de la lavadora de
presión)
B - Drip loop (boucle d’égouttement, vuelta de
goteo)
C - Extension cord (cordon prolongateurs,
cordón de extensión)
I
J
H - Trigger handle (poignée de gâchette, mango
del gatillo)
I - High-pressure hose (tuyau haute pression,
manguera de alta presión)
J - High-pressure hose storage (rangement de
tuyau haute pression, almacenamiento del
manguera de alta presión)
K - Handle (poignée, mango)
D
See this fold-out section for all of the figures referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner toutes les figures mentionnées dans le manuel d’utilisation.
Consulte esta sección desplegable para ver todas las figuras a las que se hace referencia en el manual del operador.
iii
Fig. 5
A - Axle (essieu, eje)
B - Wheel (roue, rueda)
C - Hitch pin (goupille de sûreté, pasador del
enganche)
A
B
Fig. 4
A - Phillips screwdriver (tournevis à pointe
cruciforme, destornillador phillips)
A
A - Button (bouton, botón)
B - Push to insert (pousser pour insérer, presione
para insertar)
Fig. 6
AA
B
B
Fig. 7
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Spray wand (poignée à gâchette, tubo
rociador)
A
B
Fig. 8
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High-pressure hose (tuyau haute pression,
manguera de alta presión)
A
B
A
B
C
A - Threaded outlet (têton fileté, conexión
roscada)
B - Collar (collier, casquillo)
C - High-pressure hose (flexible haute pression,
manguera de alta presión)
Fig. 9
A
B
A - Water intake (rise d’eau, entrada de agua)
B - Garden hose (tuyau d’arrosage, manguera de
jardín)
Fig. 11
A
B
C
A - Trigger handle holder and nozzle storage
(support d’ensemble de gâchette et
rangement de buses, sujetadore del mango
del gatillo y compartimientos para boquillas)
B - Screw (vis, tornillo)
Fig. 10
C
iv
A - Start button (bouton de démarrage, botón de
arranque)
Fig. 12
A
A - Trigger (gâchette, gatillo)
B - Lock-out (verrouillage, seguro)
A - Spray wand (lance de pulvérisation, tubo
rociador)
B - Nozzle (buse, boquilla)
C - Turbo nozzle (buse de turbo, boquilla de
turbo)
D - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
E - Push the nozzle into place (insérer en place la
buse, introduzca la boquilla en su lugar)
F - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
A
B
C
Fig. 14
A
B
DD
E
E
F
F
Fig. 13
Fig. 15
A - Cap (capuchon, tapa)
B - Soap tank (réservoir de savon, tanque de
jabón)
C - Detergent (détergente, detergente)
B
C
A
Fig. 16
Fig. 18
A - Power cord (cordon d’alimentation, cordón de
corriente)
B - Power cord storage brackets (support de
rangement pour cordon d’alimentation,
soporte para almacenamiento del cordón
eléctrico)
AB
Fig. 19
Fig. 17
A - Threaded top (bouchon vissé, parte superior
roscada)
B - Rubber seal (joint de caoutchouc, sello de
goma)
C - Paper seal (sceaux de papier, sello de papel)
D - Water intake (rise d’eau, entrada de agua)
E - Pump outlet (sortie de la pompe, orificio de
descarga de la bomba)
F - Pump protector (protecteur de pompe,
protector de bomba)
C
B
A
A
D
E
F
MOVING THE PRESSURE WASHER
DÉPLACEMENT DE LA LAVEUSE
À PRESSION
TRASLADO DE LA LAVADORA
DE PRESIÓN
OFF ON
v
Fig. 20
A - Straightened paper clip (not included)
[trombone droit (non inclus), clip para papel
abierto (no incluido)]
B - Nozzle (embout, boquilla)
A
B
Fig. 21 Fig. 22
TO STORE THE MACHINE
REMISAGE DE LA MACHINE
PARA GUARDAR LA MÁQUINA
Page 2 — English
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
WARNING:
When using this product basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
THIS PRODUCT
To reduce the risk of injury, close supervision is neces-
sary when a product is used near children.
Be thoroughly familiar with controls. Know how to stop
the product and release pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate product
when you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at
all times.
Follow the maintenance instructions specified in this
manual.
This product is provided with a ground fault circuit
interrupter built into the power cord plug. If replace-
ment of the plug or cord is needed, use only identical
replacement parts.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or
break down, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
product is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug
must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
DANGER: Improper connection of the equipment-grounding
conductor can result in a risk of electrocution. Check with a
qualified electrician or service personnel if you are in doubt
as to whether the outlet is properly grounded. Do not modify
the plug provided with the product – if it will not fit the outlet,
have a proper outlet installed by a qualified electrician. Do
not use any type of adaptor with this product.
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
This pressure washer is provided with a ground-fault circuit-
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that
include GFCI protection.
EXTENSION CORDS
See Figure 1.
Use only 3-wire extension cords that have 3-prong grounding-
type plugs and 3-pole cord connectors that accept the plug
from the product. Use only extension cords that are intended
for outdoor use. These extension cords are identified by a
marking “Acceptable for use with outdoor appliances; store
indoors while not in use.” Use only extension cords having
an electrical rating not less than the rating of the product. Do
not use damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse exten-
sion cord and do not yank on any cord to disconnect. Keep
cord away from heat and sharp edges. Always disconnect
the extension cord from the receptacle before disconnecting
the product from the extension cord.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug with
wet hands.
To avoid the possibility of the product plug or outlet getting
wet, the operator should arrange a “drip loop” in the cord
connecting the product to the outlet. The “drip loop” is that
part of the cord below the level of the outlet, or the connector
if an extension cord is used, to prevent water traveling along
the cord and coming in contact with the outlet.
Page 3 — English
SPECIFIC SAFETY RULES
Use caution when positioning the pressure washer for
use. Warm air from the motor could cause discolored spots
on grass.
Know your product. Read the operator’s manual care-
fully. Learn the machine’s applications and limitations as
well as the specific potential hazards related to this prod-
uct.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Use right product. Don’t force product or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
Dress properly. Wear long pants and long sleeves. Do
not wear loose clothing, neckties, or jewelry. They can get
caught and draw you into moving parts. Rubber gloves
and nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain
long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
 Alwaysweareyeprotectionwithsideshieldsmarked
to comply with ANSI Z87.1. Following this rule will reduce
the risk of serious personal injury.
Use only recommended accessories. The use of im-
proper accessories may cause risk of injury.
Check damaged parts. Before further use of the product,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and per-
form its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect its operation.
A guard or other part that is damaged must be properly
repaired or replaced by an authorized service center to
avoid risk of personal injury.
Never leave product running unattended. Turn power
off. Don’t leave product until it comes to a complete stop.
Keep the motor free of grass, leaves, or grease to reduce
the chance of a fire hazard.
Follow manufacturer’s recommendations for safe load-
ing, unloading, transport, and storage of machine.
Keep product dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake
fluids, gasoline, petroleum-based products, or any solvents
to clean product.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
that can be thrown or become entangled in the
machine.
Do not use product if switch does not turn it off. Have
switch replaced by an authorized service center.
Avoid dangerous environment. Don’t expose to rain.
Keep work area well lit.
Do not abuse the cord. Never use the cord to carry the
product or to disconnect the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase the
risk of electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the product. Receptacles are available with built-
in GFCI protection and may be used for this measure of
safety.
This pressure washer is not recommended for use with
an extension cord. If an extension cord must be used,
please make sure it is in good condition. When using
an extension cord, be sure to use one heavy enough to
carry the current your product will draw. A wire gauge size
(A.W.G.) of at least 12 is recommended for an extension
cord 25 feet (7.6 m) or less in length. If in doubt, use the
next heavier gauge. The smaller the gauge number, the
heavier the cord. An undersized cord will cause a drop in
line voltage, resulting in loss of power and overheating.
WARNING: Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil or
grease.
Never direct a water stream toward people or pets, or
any electrical device.
Before starting any cleaning operation, close doors and
windows. Clear the area to be cleaned of debris, toys, out-
door furniture, or other objects that could create a hazard.
Never pick up or carry the machine while the motor
is running.
 Never start the machine if ice has formed in any part
of the equipment.
Do not use acids, alkalines, solvents, flammable ma-
terial, bleaches, or industrial-grade solutions in this
product. These products can cause physical injuries to
the operator and irreversible damage to the machine.
WARNING: High-pressure jets can be dangerous if sub-
ject to misuse. The jet must not be directed at persons,
animals, electrical devices, or the machine itself.
Keep the motor away from flammables and other haz-
ardous materials.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious motor problems.
Before storing, allow the motor to cool.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause prod-
uct damage.
ONLY use cold water.
Page 4 — English
SPECIFIC SAFETY RULES
Make sure minimum clearance of 3 feet (90 cm) is
maintained from combustible materials.
Never spray close to the surface to be cleaned, as you
can damage the surface.
After stopping the motor, always pull the trigger on the
trigger handle to relieve stored pressure in the high-
pressure hose. Failure to do so could result in serious
personal injury.
Ensure the high-pressure hose is properly connected
before using the product.
Connect pressure washer only to an individual branch
circuit.
Hold the trigger handle securely with both hands. Ex-
pect the trigger handle to move when the trigger is pulled
due to reaction forces. Failure to do so could cause loss
of control and injury to yourself and others.
For outdoor use only.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
product, loan them these instructions also.
Page 5 — English
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates a hazardous situation, which, if not avoided, will result in death or serious
injury.
WARNING: Indicates a hazardous situation, which, if not avoided, could result in death or seri-
ous injury.
CAUTION: Indicates a hazardous situation, that, if not avoided, may result in minor or moder-
ate injury.
NOTICE: (Without Safety Alert Symbol) Indicates information considered important, but not
related to a potential injury (e.g. messages relating to property damage).
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual To reduce the risk of injury, user must read and understand operator’s
manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply with
ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations, and never direct a
water stream toward any electrical device.
Risk of Injection
To reduce the risk of injection or injury, never direct a water stream
towards people or pets or place any body part in the stream. Leaking
hoses and fittings are also capable of causing injection injury. Do not
hold hoses or fittings.
Kickback To reduce the risk of injury from kickback, hold the spray wand securely
with both hands when the machine is on.
Electric Shock Do not use near electric power lines or receptacle outlets.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS, ALKALINES,
BLEACHES, SOLVENTS, FLAMMABLE MATERIAL, OR INDUSTRIAL
GRADE SOLUTIONS in this product.
Risk of Explosion Do not spray flammable liquids. Flammable liquids and their vapors
are explosive and can cause severe burns or death.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits, etc., per minute
Page 6 — English
ELECTRICAL
GROUNDING INSTRUCTIONS
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock.
This product is equipped with an electric cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING:
Improper installation of a grounded plug increases the
risk of electric shock. When repair or replacement of the
cord or plug is required, take the tool to an authorized
service center.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the product is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 V circuit and has a
grounding plug similar to the plug illustrated in figure 2. Only
connect the product to an outlet having the same configura-
tion as the plug. Do not use an adapter with this product.
GROUND FAULT CIRCUIT INTERRUPTER
See Figure 2.
This unit is equipped with a Ground Fault Circuit Interrupter
(GFCI), which guards against the hazards of ground fault
currents. An example of ground fault current is the current
that would flow through a person who is using an appliance
with faulty insulation and, at the same time, is in contact
with an electrical ground such as a plumbing fixture, wet
floor, or earth.
GFCI plugs do not protect against short circuits, overloads,
or shocks.
NOTE: To ensure readiness for use, press the reset button
each time you connect the pressure washer to the power
supply.
The GFCI plug can be tested with the TEST and RESET
buttons.
To test:
Press the TEST button. You will hear a “click” sound and
the LED light will go out.
To restore power, press the RESET button. The LED light
will illuminate to indicate power has been restored.
Perform this test monthly to ensure proper operation of the
GFCI.
To reduce the risk of electric shock the supervi-
sory circuit must be operated before an appliance is
plugged into any receptacle on the device.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, possibly
resulting in overheating, loss of power, and/or circuit
breaker or GFCI tripping. Use the chart to determine the
minimum wire size required in an extension cord. Only round
jacketed cords listed by Underwriter’s Laboratories (UL)
should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during
use. Make a knot, then connect the plug end of the power
cord into the receptacle end of the extension cord. This
method can also be used to tie two extension cords together.
NOTE: This pressure washer is not recommended for
use with an extension cord. If using an extension cord,
arrange a drip loop to avoid the possibility of the tool
plug getting wet (see page 2).
USE ONLY THIS SIZE EXTENSION CORD WHEN USING
THIS PRODUCT:
Cord Length Wire Size (A.W.G.)
25 ft. / 7.6 m 12
50 ft. / 15.2 m Not Allowed
NOTE: A.W.G. = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are working
with a power tool. Failure to do so can result in serious
personal injury.
WARNING:
Check extension cords before each use. If damaged,
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be
connected to a power supply that is nominal 120V/60Hz
AC (typical U.S. household circuit). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
Page 7 — English
FEATURES
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-877-617-3501 for assistance.
PACKING LIST
Electric Pressure Washer
25 ft. (7.6 m) High-Pressure Hose
Handle
Trigger Handle
Spray Wand
Trigger Handle and Nozzle Storage Bracket
Phillips Head Screws (2)
Wheels (2)
Axles (2)
Hitch Pins (2)
Nozzles (15º, Turbo, Soap)
Operator’s Manual
PRODUCT SPECIFICATIONS
Maximum Pounds Per Square Inch* ........................................................................................................................1,900 psi
Maximum Gallons Per Minute ...................................................................................................................................1.2 GPM
Input ...........................................................................................................................nominal 120V/60Hz AC only, 13 Amps
*Max. rating determined by PWMA Standard 101
KNOW YOUR PRESSURE WASHER
See Figure 3.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard
against the hazards of ground fault currents. This plug does
not protect against short circuits, overloads, or shocks.
POWER CORD STORAGE BRACKETS
Store the power cord on the convenient storage brackets
when the pressure washer is not in use. Rotate the left bracket
clockwise and remove for quick release of the cord.
SOAP TANK
Remove the cap from the soap tank to add detergent to the
pressure washer.
START BUTTON
This button turns the pressure washer on and off.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides added
control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock-out provides protection against
unauthorized use.
Page 8 — English
ASSEMBLY
WARNING:
If any parts are damaged or missing, do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
TOOLS NEEDED
See Figure 4.
The following tool (not included or drawn to scale) is needed
for assembly:
Phillips Screwdriver
INSTALLING THE WHEELS
See Figure 5.
 Locate the axles, hitch pins, and wheels.
 Slide the axle through the hole in the center of the wheel.
Lift the machine and slide the axle into the wheel mounting
hole in the machine base as shown.
 Push the hitch pin into the hole on the end of the axle to
secure the wheel assembly.
NOTE: The hitch pin should be pushed into the axle until
the center of the pin rests on top of the axle.
 Repeat with the second wheel.
INSTALLING HANDLE AND TRIGGER
HANDLE AND NOZZLE STORAGE BRACKET
See Figure 6 - 7.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the frame.
Installing handle:
Align the handle with the holes in the frame.
Push and hold the button on the handle.
Installing trigger handle holder and nozzle storage
bracket:
 Align trigger handle holder with holes in handle, as shown.
 Install screws and tighten securely.
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 8.
 Push the end of the spray wand into the trigger handle
and rotate clockwise to secure.
Pull on the spray wand to be certain it is properly secured.
Place the assembled spray wand in the trigger handle
storage bracket.
CONNECTING THE HIGH-PRESSURE HOSE TO
THE TRIGGER HANDLE
See Figure 9.
Remove the high-pressure hose from the hose storage
strap.
Screw the collar on the high-pressure hose into the trigger
handle inlet coupler by turning the hose collar clockwise.
Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE PUMP
See Figure 10.
Completely uncoil and straighten the high-pressure hose
to prevent kinks.
NOTE: See Using the High-Pressure Hose in Operation
(See Page 13) for more information about using the high-
pressure hose.
Align the collar on the hose to the threaded outlet on the
pump.
Install the high-pressure hose collar onto the threaded
outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
Page 9 — English
ASSEMBLY
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 11.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into the
drinking water supply. Direct connection through a
receiver tank or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet (3.1 m) of
unrestricted hose between the pressure washer intake
and the hose faucet or shut-off valve (such as a “Y” shut-
off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high-
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Page 10 — English
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 12.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high-
pressure seals and decrease pump life. Completely unwind
the hose from its reel or coil and make sure the hose is not
being restricted by tires, rocks, or any other objects that
may lessen or prevent water flow to the pressure washer.
Before starting the motor:
Connect all hoses.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the motor:
With the start button in the OFF position, connect the
pressure washer to the power supply.
NOTE: If using an extension cord, make sure to arrange
a drip loop as described on page 2.
WARNING:
To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch plug with wet hands.
Press the reset button on the pressure washer’s plug to
make sure the unit is ready for operation.
Push the start button to the ON position to start the motor.
NOTE: The light should be off until the start button is
pressed in the ON position. The light will stay illuminated
until the start button is pressed again to turn the unit off.
NOTICE:
Routinely make a visual inspection of the pump and
motor during use. If you notice any lubricant leaking
around the pump or motor seals, stop using the pres-
sure washer immediately. Contact customer service or
a qualified service center for repair. Failure to do so may
cause property damage.
OPERATION
WARNING:
Do not allow familiarity with the product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
WARNING:
Never direct a water stream toward people or pets, or
any electrical device. Failure to follow these instruc-
tions could result in serious injury, electric shock, or
death.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts,
caps, etc. Tighten securely all fasteners and caps and
do not operate this product until all missing or damaged
parts are replaced. Please contact customer service or
a qualified service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills, play-
ground equipment, etc.
*Always test in an inconspicuous area first.
Page 11 — English
OPERATION
To stop the motor:
Push the start button again to stop the motor.
Pull trigger to release water pressure.
NOTE: The pressure washer may be on and the system may
have pressure even when the pump and/or motor cannot
be heard running. Always use caution around the pressure
washer.
USING THE TRIGGER HANDLE
See Figure 13.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock-out:
Push up on the lock -out until it clicks into the slot.
To disengage the lock-out:
Push the lock-out down and into its original position.
Start with the nozzle 1-2 ft. (30-60 cm) away from the cleaning
surface and carefully approach the surface just until the
desired level of cleaning is achieved. If the spray is too close,
it can damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 14.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more informa-
tion about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the mo-
tor, relieving the water pressure in the trigger handle, and
locking the lock-out on the trigger handle. NEVER point
the nozzle at your face or at others. The quick-connect
feature contains small springs that could eject the nozzle
with some force. Failure to follow these instructions could
result in an eye injury or other serious personal injury.
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
Turbo Nozzle 15º Blue or Black
Soap Nozzle
Concrete, Brick, Masonry   
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
Page 12 — English
OPERATION
To connect a nozzle to the spray wand:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH-PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high-
pressure hose prior to and during each use and do
not allow it to become kinked. The high-pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high-pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high-pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 15 - 16.
As sold, this unit is designed for use with “downstream”
pressure washer detergents. To convert for use with
“upstream” detergents, contact an authorized customer
service center for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Disconnect pressure washer from power supply.
Pour detergent in the soap tank.
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process, make sure the unit is
cleaned and dried before proceeding.
NOTE: The machine setting of this unit is 20:1, which usu-
ally allows the use of 1 gallon pressure washer detergent
without further dilution. Check your detergent instructions
to be sure additional dilution is not necessary.
Install the blue or black soap nozzle on the spray wand.
Connect unit to power supply and turn the pressure
washer on.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
Before shutting off the motor:
Fill the soap tank with clean water.
Spray the clear water through the spray wand until the
tank is empty.
If any detergent remains in the spray, repeat with a second
tank of clean water.
Shut off the motor.
NOTE: Shutting off the motor will not relieve pressure in the
system. Pull trigger to release water pressure.
Page 13 — English
OPERATION
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Remove the soap nozzle and place in the nozzle storage
area.
Select the right nozzle for the job. See the chart shown
earlier in the manual to select the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
USING PUMP PROTECTOR
See Figure 17.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should
be added to the unit after every use and before storage.
Pump protector can be purchased at the retailer where you
purchased your pressure washer, or by calling customer
service.
The instructions that follow are typical for adding pump
protector but you should always verify the specific instructions
provided by the manufacturer of the pump protector used.
Turn off the pressure washer motor and shut off the water
supply. Pull trigger to release water pressure.
Disconnect garden hose and high-pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
Pump is protected when the protector fluid exits the pump
outlet.
POWER CORD STORAGE
See Figure 18.
When it is not in use, the power cord may be wrapped around
the two brackets on the back of the unit.
To secure the power cord in place, flip the bracket to the
up position.
MOVING THE PRESSURE WASHER
See Figure 19.
NOTE: Never lift or carry this product using the handle and
never place the unit in any position other than upright on
its wheels.
Turn the pressure washer off. Point nozzle in a safe direc-
tion and pull trigger to release water pressure.
Tilt the machine toward you slightly until it balances on
the wheels then roll the machine to the desired position.
Do not tilt forward or sideways when moving.
DO NOT attempt to move the unit by pulling on any of
the hoses.
MAINTENANCE
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off motor, wait for all moving parts to stop, discon-
nect unit from power supply, and pull trigger to release
water pressure. Failure to follow these instructions can
result in serious personal injury or property damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call customer service or contact an
authorized service center for assistance.
Page 14 — English
MAINTENANCE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic, which could result in serious personal
injury.
PUMP LUBRICATION
The pump on this unit is lubricated with a sufficient amount
of high-grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is
required.
PUMP MAINTENANCE
Routinely make a visual inspection of the pump. If you
notice any leaking of lubricant around the pump seals, take
the pressure washer to a qualified service center for repair.
There are no user serviceable parts to the pressure washer
pump. Any attempt to service or alter the pump may damage
the pressure washer and void your product warranty.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
must be done by an authorized service center in order to
avoid a safety hazard.
NOZZLE MAINTENANCE
See Figure 20.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
Unplug the pressure washer.
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Remove the nozzle from the spray wand.
WARNING:
NEVER remove nozzles without first turning off the
motor, and locking the lock-out on the trigger handle.
NEVER point the nozzle at your face or at others. The
quick-connect feature contains small springs that could
eject the nozzle with some force. Failure to follow these
instructions could result in an eye injury or other serious
personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle (not included).
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
STORING THE PRESSURE WASHER
See Figures 21 - 22.
NOTE: Regular use of pump protector will give you better
performance of the unit and increase the life of the pump.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses, the pump, and the soap tank
before storing.
Make sure the start button is in the OFF position (O).
Disconnect both the high-pressure hose and the garden
hose from the pump.
Tilt the unit as shown to allow any remaining water in the
pump to drain from the water inlet.
NOTICE:
If the location where your pressure washer is stored will
fall below 32°F (0°C), the use of a pump protector is re-
quired before storing to prevent freeze damage. Freeze
damage will void your warranty.
Neatly coil the high-pressure hose and store with hook-
and-loop strap.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
Page 15 — English
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE SOLUTION
Pressure washer does not start when
trigger is depressed
Power cord not connected to power
source
The start button is in the OFF position
(O)
GFCI is tripped
House/shop circuit breaker is tripped
Water pressure in hose
Receptacle is bad
Connect the power cord to a live 120V
AC, 60 Hz AC receptacle.
Put the start button in the ON position (I).
Press reset button on the GFCI plug.
Reset house/shop breaker. Make sure
pressure washer is connected to an
individual branch circuit only. If using an
extension cord, make sure it is heavy
enough to carry the current of the pressure
washer.
Squeeze trigger to relieve water pressure.
Try another receptacle.
Pump doesn’t produce pressure Inadequate water supply
Spray wand leaks
Nozzle is clogged
Pump is faulty
Air in line
Water inlet filter is clogged or dirty
Provide adequate water flow.
Check connections and/or replace wand.
Clean nozzle.
Contact authorized service center.
Squeeze trigger on spray wand to remove
air from line.
Remove the water inlet filter, rinse with
warm water, then replace in unit.
Machine doesn’t reach high pressure Diameter of garden hose is too small
Water supply is restricted
Not enough inlet water
Hose is leaking
Kink in hose
Replace with 3/4 in. (19 mm) garden hose.
Check garden hose for kinks, leaks, and
blockages.
Open water source full force.
Replace hose.
Eliminate kinks in hose.
No detergent Soap tank is empty
Water supply is inadequate or clogged
Wrong nozzle is attached
Add additional detergent to tank.
Check garden hose for kinks, leaks and
blockages.
Attach blue or black soap nozzle.
Wand leaks O-ring needs replacing Replace o-ring. If this does not correct the
problem, contact your authorized service
center to purchase a new wand.
This product has a Two-year Limited Warranty for personal, family,
or household use (90 days for business or commercial use).
For warranty details, visit www.powerstroketools.com
or call (toll free) 1-877-617-3501.
Page 2 — Français
INSTRUCTIONS IMPORTANTES CONCERNANT LA SÉCURITÉ
AVERTISSEMENT :
Lire attentivement toutes les instructions. Le non-
respect de toutes les instructions ci-dessous peut
entraîner un choc électrique, un incendie et/ou des bles-
sures graves.
AVERTISSEMENT :
Lors de l’utilisation de ce produit, toujours suivre les
consignes de base, notamment :
LIRE TOUTES LES INSTRUCTIONS AVANT
D’UTILISER CE PRODUIT
Pour réduire les risques de blessures, porter une
attention particulière lorsque le produit est utilisé en
présence d’enfants.
Se familiariser complètement avec les commandes.
Veiller à savoir arrêter la machine et relâcher la pression
rapidement.
Rester vigilant et garder le contrôle. Se montrer attentif
et faire preuve de bon sens. Ne pas utiliser le produit en
état de fatigue. Ne pas se presser.
Ne pas utiliser ce produit sous l’influence de l’alcool,
de drogues ou de médicaments.
Ne laisser personne approcher la zone de travail,
particulièrement les petits enfants et les animaux
domestiques.
Ne pas travailler hors de portée ou se tenir sur une
échelle, un échafaudage, un toit ou un surface instable.
Toujours se tenir bien campé et en équilibre.
Suivre les instructions d’entretien décrites dans le
présent manuel.
Ce produit est fourni avec un disjoncteur de fuite à la
terre intégré dans la fiche du cordon d’alimentation.
S’il est nécessaire de procéder au remplacement de la
fiche ou du cordon, utiliser exclusivement des pièces
identiques à celles d’origine.
AVERTISSEMENT : Risque d’injection ou de blessures
– ne pas diriger le jet directement vers quelqu’un.
CONSERVER CES INSTRUCTIONS
INSTRUCTIONS DE MISE À LA TERRE
Ce produit doit être mis à la terre. En cas de mauvais
fonctionnement ou de panne, la mise à la terre offre une
trajectoire de moindre résistance du courant électrique afin
de réduire les risques d’électrocution. Ce produit est livré
avec un cordon équipé d’un conducteur de terre et d’une fiche
de mise à la terre. Cette fiche doit être branchée dans une
prise de courant avec mise à la terre installée correctement
et conforme à tous les règlements et toutes les lois locales.
DANGER : Le branchement inadéquat du conducteur de
terre représente un risque d’électrocution. En cas de doute
concernant la mise à la terre de la prise, demander à un
électricien ou à un réparateur qualifié. Ne pas modifier la
fiche fournie avec ce produit. Si la fiche ne s’insère pas
dans la prise, faire installer une prise de courant adéquate
par un électricien qualifié. Ne pas utiliser aucun adaptateur
avec ce produit.
PROTECTION D’UN DISJONCTEUR DE FUITE
À LA TERRE
Cette laveuse à pression est fournie avec un disjoncteur de
fuite à la terre intégré dans la fiche du cordon d’alimentation.
Ce dispositif offre une protection supplémentaire contre les
décharges électriques. S’il est nécessaire de procéder au
remplacement de la fiche ou du cordon, utiliser exclusivement
des pièces identiques à celles d’origine qui incluent un
disjoncteur de fuite à la terre.
CORDONS PROLONGATEURS
Voir la figure 1.
Utiliser seulement des rallonges à 3 brins équipées de fiches
à 3 lames et des connecteurs à 3 pôles adaptés à la fiche de
ce produit. Utiliser uniquement des cordons prolongateurs
conçus pour l’extérieur. Ces cordons prolongateurs sont
étiquetés « Compatibles avec les appareils extérieurs;
entreposer à l’intérieur lorsque le produit n’est pas utilisé ».
Utiliser uniquement des cordons prolongateurs dont
les caractéristiques électriques ne sont pas inférieures
à la puissance du produit. Ne pas utiliser des cordons
prolongateurs endommagés. Examiner le cordon prolongateur
avant de l’utiliser et le remplacer s’il est endommagé. Ne pas
malmener les cordons prolongateurs ni tirer d’un coup sec
dessus pour les débrancher. Garder le cordon à l’écart de
la chaleur et des rebords tranchants. Toujours débrancher
le cordon prolongateur de la prise de courant avant de
débrancher le produit du cordon prolongateur.
AVERTISSEMENT : Pour réduire le risque d’électrocution,
garder toutes les connexions au sec et au-dessus du sol.
Ne pas manipuler la fiche avec les mains mouillées.
L’opérateur doit former un anneau d’écoulement avec le
cordon du produit branché à la prise de courant de façon à
prévenir l’infiltration d’eau dans la prise de courant ou sur
la fiche. Cet anneau d’écoulement est la partie du cordon
se trouvant sous le niveau de la prise de courant ou du
connecteur, lorsqu’une rallonge est utilisée, préviendra
le parcours de l’eau le long du cordon et empêchera son
contact avec la prise de courant.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

PowerStroke PS141913 Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
Ce manuel convient également à