Sony VPL-HS10 Manuel utilisateur

Catégorie
Projecteurs de données
Taper
Manuel utilisateur

Ce manuel convient également à

Operating Instructions __________________________________
GB
Mode d’emploi ________________________________________
FR
Manual de instrucciones _________________________________
ES
4-091-754-13(1)
Video Projector
© 2002 Sony Corporation
VPL-HS10
Video Projector VPL-HS10
GB
2
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
For the customers in the USA
If you have any questions about this product, you may
contact:
Sony Electronics Inc.
Attn: Business Information Center (BIC)
12451 Gateway Boulevard
Ft. Myers, Florida 33913
Telephone No.: 800-686-7669
The number below is for FCC related matters only.
Declaration of Conformity
Trade Name: SONY
Model No.: VPL-HS10
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road, Oradell
NJ 07649 U.S.A.
Telephone No.: 201-930-6972
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your
authority to operate this equipment.
For the customers in Canada
This Class B digital apparatus complies with Canadian
ICES-003.
Voor de klanten in Nederland
Dit apparaat bevat een vast ingebouwde batterij die niet
vervangen hoeft te worden tijdens de levensduur van het
apparaat.
Raadpleeg uw leverancier indien de batterij toch
vervangen moet worden. De batterij mag alleen
vervangen worden door vakbekwaam servicepersoneel.
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Lever het apparaat aan het einde van de levensduur in
voor recycling, de batterij zal dan op correcte wijze
verwerkt worden.
WARNING
This symbol is intended to alert the user to
the presence of uninsulated "dangerous
voltage" within the product's enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the
appliance.
The socket-outlet should be installed near the
equipment and be easily accessible.
3
GB
Table of Contents
Precautions .............................................5
Connections and Preparations
Unpacking ...............................................6
Step 1: Installing the Projector ..............7
Before Setting Up the Projector .........................7
Using the Optional Conversion Lens .................9
Installing the Projector and a Screen
— Floor Installation .........................................10
Installing the Projector and a Screen
— Ceiling Installation ......................................12
Step 2: Connecting the Projector ........13
Connecting with Video Equipment ..................14
Connecting a Digital Tuner Using the DVI
Connector .........................................................14
Connecting a DVD Player Equipped With the
Component Output ...........................................14
Connecting an AV Amplifier ...........................14
Connecting a Computer ....................................15
Connecting Using the Optional Interface
Unit ...................................................................15
Step 3: Adjusting the Picture Size and
Position ..................................................16
Step 4: Selecting the Menu
Language ...............................................18
Projecting
Projecting the Picture on the Screen ..20
Selecting the Wide Screen Mode ........22
Selecting the Picture Viewing Mode ...24
Using the Menus
Operation through the Menus ..............25
Menu Lists .............................................27
Menu Configurations .......................................27
Menu Items ......................................................27
About the Preset Memory No. .........................30
Adjusting Picture Quality of a Signal from the
Computer .........................................................30
Using a “Memory Stick”
About a “Memory Stick” .......................31
Preparing for Viewing the Picture Files
Stored in a “Memory Stick” ..................33
Inserting a “Memory Stick” .............................33
Displaying the Desired Pictures in
Digital Camera Mode .......................................33
Viewing the Pictures .............................36
Viewing the Pictures in Sequence
— Slide Show ..................................................36
Displaying a Picture on the Full Screen
— Full Screen ..................................................37
Playing Movie Pictures ....................................38
Selecting the Folder Containing
the Desired Picture ...........................................40
Rotating a Still Picture ..........................41
Protecting an Important Picture ..........42
Projecting a Selected Picture When the
Power Is Turned On — Startup ............43
Registering a Still Picture as the
Startup Picture ..................................................43
Setting the Startup Picture ...............................44
Deleting a Picture ..................................45
Sorting the Pictures ..............................47
Displaying Either of the Still Pictures or
Movie Pictures .......................................48
Displaying the “Memory Stick”
Information ............................................49
Initializing a “Memory Stick”
— Format ...............................................50
GB
4
Others
Troubleshooting ......................................51
Replacing the Lamp .................................53
Replacing the Air Filter ...........................54
Specifications ..........................................55
Location of Controls ................................63
Front .................................................................63
Rear ..................................................................64
Remote Control ................................................65
Index .........................................................66
Precautions
5
GB
Precautions
On safety
Check that the operating voltage of your unit is
identical with the voltage of your local power
supply.
Should any liquid or solid object fall into the
cabinet, unplug the unit and have it checked by
qualified personnel before operating it further.
Unplug the unit from the wall outlet if it is not to be
used for several days.
To disconnect the cord, pull it out by the plug. Never
pull the cord itself.
The wall outlet should be near the unit and easily
accessible.
The unit is not disconnected to the AC power source
(mains) as long as it is connected to the wall outlet,
even if the unit itself has been turned off.
Do not look into the lens while the lamp is on.
Do not place your hand or objects near the
ventilation holes. The air coming out is hot.
On preventing internal heat build-up
After you turn off the power with the I / 1 (on/
standby) switch, do not disconnect the unit from the
wall outlet while the cooling fan is still running.
Caution
The projector is equipped with ventilation holes
(intake) and ventilation holes (exhaust). Do not block
or place anything near these holes, or internal heat
build-up may occur, causing picture degradation or
damage to the projector.
On repacking
Save the original shipping carton and packing
material; they will come in handy if you ever have to
ship your unit. For maximum protection, repack your
unit as it was originally packed at the factory.
GB
6
Unpacking
Connections
and
Preparations
Unpacking
Check the carton to make sure it contains the
following items:
Remote control (1),
Size AA (R6)
batteries (2)
Signal interface
cable (1)
Air filter (for
replacement) (1)
Cinema filter (1)
AC power cord (1)
Operating Instructions (1)
Inserting the batteries into the remote
control
This section describes how to install the
projector and screen, how to connect the
equipment from which you want to project
the picture, etc.
Insert the batteries E side first as shown
in the illustration.
Inserting them forcibly or with the
polarities reversed may cause a short
circuit and may generate heat.
Step 1: Installing the Projector
Connections and
Preparations
7
GB
Step 1: Installing
the Projector
You can obtain good picture quality even when you
project the picture from the side of the screen (“Side
Shot”) (1 page 10). You can enjoy home
entertainment with this projector in various situations.
Enjoying home theater
Enjoying video games on a large screen
Watching sports, etc. with your company
Viewing images, recorded by a digital
camera and stored in the “Memory Stick,” on
a large screen
Before Setting Up the
Projector
Do not place the projector in the following situations,
which may cause malfunction or damage to the
projector.
Poorly ventilated
Step 1: Installing the Projector
Connections and
Preparations
GB
8
Highly heated and humid
Very dusty and extremely smoky
Do not use the projector under the following
conditions:
Tilting the unit extremely
Blocking the ventilation holes
Note
Installing the unit at altitudes
When using the projector at an altitude of 1,500 m or
higher, turn on high altitude mode in the INSTALL
SETTING menu. Failing to set this mode when using
the projector at high altitudes could have adverse
effects, such as reducing the reliability of certain
components.
Using the supplied Cinema Filter
The Cinema Filter is supplied with the projector,
allowing you to receive higher contrast color and
emphasized black color by attaching or removing.
Use it according to preference.
To attach the Cinema Filter
1 Detach the lens hood stopper to remove
the lens hood.
2 Insert the Cinema Filter, aligning its screw
with the thread around the projector’s
lens, then turn the Filter clockwise.
3 Attach the lens hood by turning it
counterclockwise until it clicks, and fix the
lens hood with the lens hood stopper.
To remove the Cinema Filter
Perform step 1 above, then turn the Cinema Filter
counterclockwise to remove.
15˚
15˚
Ventilation
holes
(exhaust)
Ventilation
holes
(intake)
Lens hood stopper Lens hood
Step 1: Installing the Projector
Connections and
Preparations
9
GB
Using the Optional
Conversion Lens
You can install the following two types of lenses
(optional) on the projector. For projection distances
when installing the Conversion Lens, see page 58.
VPLL-CT10 Long Focused Conversion Lens
VPLL-CW10 Short Focused Conversion Lens
Follow the steps below to install the Conversion Lens.
For details on installing the Lens, refer also to the
installation manual supplied with the Lens.
1 Turn off the power and disconnect the
power cord.
2 Remove the lens hood from the projector’s
lens, and remove the lens cap from the
Conversion Lens.
3 Align the screw of the Conversion Lens
with the thread around the lens of the
projector as illustrated below.
4 Turn the Conversion Lens clockwise until
you hear it click.
Note
If the Conversion Lens is hard to turn, turn it slightly
counterclockwise first, then turn it clockwise.
5 Place a thick cloth (e.g., a cushion)
beneath the projector. Place the projector
face down.
Notes
You cannot install the Conversion Lens on the projector’s
lens with the Cinema Filter attached. Remove the Cinema
Filter when you install the Conversion Lens.
The optional Conversion Lens projects from the top of the
projector when the Lens is installed on the projector. Before
installation, place a cloth of adequate thickness beneath the
projector to keep the Lens from contact with the floor or a
desk top. Otherwise, the Lens may malfunction if it
receives too much pressure from the weight of the
projector.
6 Fasten the end of the safety wire of the
Conversion Lens to the bottom of the
projector using the screw supplied with
the Conversion Lens (M5×8, with washer).
Note
Be sure to fasten the end of the safety wire of the Lens to the
bottom of the projector.
When installing the projector on the ceiling
Be sure to fasten the end of the safety wire of the Lens
to both the projector and the PSS-610 Projector
Suspension Support in step 6, as illustrated below. In
this case, use the screw (M5×12, with washer)
supplied with the PSS-610.
First, place the PSS-610 ( 1 ) on the projector, then
place the safety wire ( 2 ) on the PSS-610.
WARNING
Be sure to use the screw (M5×12 with washer) supplied with the
PSS-610. Never use the screw supplied with the Conversion Lens.
If you use the screw supplied with the Lens, the Lens may fall
from the projector and may cause injury.
Notes on installation of the optional Conversion Lens
The Lens scratches easily, so when handling it, always place it
gently on a stable and level surface in a horizontal position.
Be sure not to bump the Lens on the surface of the lens of the
projector.
Avoid touching the Lens surface.
1
2
End of safety wire
PSS-610 Projector
Suspension
Support
Step 1: Installing the Projector
Connections and
Preparations
GB
10
To remove the installed Conversion Lens
1 Remove the end of the safety wire of the
installed Lens from the bottom of the
projector by removing the screw.
2 Turn the installed Lens counterclockwise
until it can be removed.
Notes
Be sure not to drop the uninstalled Conversion Lens.
When you adjust picture distortion using “V Keystone” or
“Side Shot” in the INSTALL SETTING menu with the
optional Conversion Lens attached to the projector, the
aspect ratio of the original picture may not be correctly
displayed.
Installing the Projector and a
Screen — Floor Installation
The installation distance between the projector and
screen varies depending on the size of the screen.
1
Determine the installation
position of the projector and
screen.
a: Minimum projection distance between the
screen and the center of the projector’s lens
when you place the projector on the side
(“Side Shot”), or when you place the
projector with the center of the screen and the
center of the lens aligned.
b: Maximum projection distance between the
screen and the center of the projector’s lens
when you place the projector on the side, or
when you place the projector with the center
of the screen and the center of the lens
aligned.
c: Maximum horizontal distance between the
right/left end of the screen and the center of
the projector’s lens when the projector is
placed on the side (when you use projection
distance a)
d: Maximum horizontal distance between the
right/left end of the screen and the center of
the lens when the projector is placed on the
side (when you use projection distance b)
e: Maximum vertical distance from the bottom
of the screen to the center of the projector’s
lens when you place the projector on the side
(when you use projection distance a)
f: Maximum vertical distance from the bottom
of the screen to the center of the projector’s
lens when you place the projector on the side
(when you use projection distance b)
When projecting using both “Side Shot”
and “V Keystone” adjustments
Position the projector with the lens end within
the area in the illustration, by using the
values a to f in the table below as a guide.
Unit: m (feet)
a
e
f
b
c
d
12˚
12˚
f
Screen
Projector
Screen size
(inches)
40 60 80 100 120
a
1.6
(5.2)
2.4
(7.9)
3.2
(10.5)
4.0
(13.1)
4.8
(15.7)
b
1.8
(5.9)
2.8
(9.2)
3.7
(12.1)
4.7
(15.4)
5.6
(18.4)
c
–0.1
(–0.3)
–0.1
(–0.3)
–0.2
(–0.6)
–0.2
(–0.6)
–0.3
(–1.0)
d
0.0
(0.0)
0.0
(0.0)
0.0
(0.0)
0.0
(0.0)
0.0
(0.0)
e
0.3
(1.0)
0.5
(2.0)
0.7
(2.3)
0.8
(2.6)
1.0
(3.3)
f
0.4
(1.6)
0.6
(2.0)
0.8
(2.6)
1.0
(3.3)
1.2
(3.9)
Screen size
(inches)
150 180 200 250 300
a
6.0
(19.7)
7.3
(24.0)
8.1
(26.6)
10.1
(33.1)
12.1
(39.7)
b
7.0
(23.0)
8.4
(27.6)
9.4
(30.8)
11.7
(38.4)
14.1
(46.3)
c
–0.3
(–1.0)
–0.4
(–1.3)
–0.4
(–1.3)
–0.5
(–1.6)
–0.6
(–1.6)
d
–0.1
(–0.3)
–0.1
(–0.3)
–0.1
(–0.3)
–0.1
(–0.3)
–0.1
(–0.3)
e
1.3
(4.3)
1.5
(4.9)
1.7
(5.6)
2.1
(6.9)
2.5
(8.2)
f
1.5
(4.9)
1.8
(5.9)
1.9
(6.2)
2.4
(7.9)
2.9
(9.5)
Step 1: Installing the Projector
Connections and
Preparations
11
GB
Tip
The tables show the distances when projecting the
conventional video and 1080i format signals. Distances
used for projecting a 720p format signal, computer’s signal
and data stored in the “Memory Stick” are shown on page
57.
Note
When projecting with the optional Conversion Lens
attached, the values a, b, e and f are slightly different from
those in the table.
When projecting using “Side Shot
adjustment only
Position the projector with the lens end within
the area in the illustration, by using the
values a, b, c and d in the table below as a guide.
Unit: m (feet)
Tip
The tables show the distances when projecting the 15kHz
RGB/component, progressive component, DTV (480i/
480p/575i/575p), composite video and Y/C video signals.
Distances used for projecting a 1080i/720p format signal,
computer’s signal and data stored in the “Memory Stick”
are shown on page 57.
Note
If you project the picture using “Side Shot” only, set “V
Keystone” in the INSTALL SETTING menu to “Manual,
and adjust the level to “0.
When projecting from the center
You can change the projection angle using the
adjuster. (1 page 18)
Position the projector with the lens end within
the area in the illustration, by using the
values a and b in the table below as a guide.
Unit: m (feet)
2
Project an image on the screen
and adjust the picture so that it
fits the screen. (1 page 16)
To project an image, connect video equipment to
the projector. (1 page 13)
Screen
size
(inches)
40 60 80 100 120
a
1.6
(5.2)
2.4
(7.9)
3.2
(10.5)
4.0
(13.1)
4.8
(15.7)
b
1.8
(5.9)
2.8
(9.2)
3.7
(12.1)
4.7
(15.4)
5.6
(18.4)
c
0.2
(0.7)
0.3
(1.0)
0.3
(1.0)
0.4
(1.3)
0.5
(1.6)
d
0.3
(1.0)
0.4
(1.3)
0.6
(2.0)
0.7
(2.3)
0.9
(3.0)
Screen
size
(inches)
150 180 200 250 300
a
6.0
(19.7)
7.3
(24.0)
8.1
(26.6)
10.1
(33.1)
12.1
(39.7)
b
7.0
(23.0)
8.4
(27.6)
9.4
(30.8)
11.7
(38.4)
14.1
(46.3)
c
0.7
(2.3)
0.8
(2.6)
0.9
(3.0)
1.1
(3.6)
1.4
(4.6)
d
1.1
(3.6)
1.3
(4.3)
1.5
(4.9)
1.9
(6.2)
2.2
(7.2)
Screen
size
(inches)
40 60 80 100 120
a
1.5
(4.9)
2.3
(7.5)
3.1
(10.2)
3.9
(12.8)
4.6
(15.1)
b
1.8
(5.9)
2.8
(9.2)
3.7
(12.1)
4.7
(15.4)
5.6
(18.4)
Screen
size
(inches)
150 180 200 250 300
a
5.8
(19.0)
7.0
(23.0)
7.8
(25.6)
9.7
(31.8)
11.7
(38.4)
b
7.0
(23.0)
8.4
(27.6)
9.4
(30.8)
11.7
(38.4)
14.1
(46.3)
Step 1: Installing the Projector
Connections and
Preparations
GB
12
Installing the Projector and a
Screen — Ceiling Installation
Use the PSS-610 Projector Suspension Support when
you install the projector on a ceiling.
a: Distance between the center of the lens and the
screen
b: Distance between the ceiling and the center of the
lens
x: Distance between the ceiling and the center of the
screen
When using the 16:9 aspect ratio screen
Unit: mm (inches)
To calculate the installation measurements (SS: Screen Size)
a (minimum) ={(SS × 33.56/0.8788) – 56.520408} × 1.025
a (maximum) ={(SS × 42.359182/0.8788) – 57.18141} × 0.975
x = b + (SS/0.8788 × 5.516)
When using the 4:3 aspect ratio screen
Unit: mm (inches)
To calculate the installation measurements (SS: Screen Size)
a (minimum) ={(SS × 33.56/0.7240) – 58.520408} × 1.025
a (maximum) ={(SS × 41.3591819/0.7240) – 57.181415} × 0.975
x = b + (SS/0.7240 × 5.516)
Attaching the projector suspension
support PSS-610
When installing the projector on the ceiling, use the
PSS-610 Projector Suspension Support. For more
details on the ceiling installation, refer to the
Installation manual for Dealers of the PSS-610. The
installation measurements are shown below when you
install the projector on the ceiling.
SS (inches) 80 100 120 150
a
Minimum
3072
(121)
3855
(151
5
/8)
4638
(182
3
/4)
5812
(228
7
/8)
Maximum
3704
(145
3
/4)
4644
(182
3
/4)
5584
(219
3
/4)
6994
(275
1
/4)
x
b+502
(b+19
7
/8)
b+628
(b+24
3
/4)
b+753
(b+29
3
/4)
b+924
(b+37
1
/8)
b
When using the PSS-610, adjustable with
243/268/293/343/368/393 mm
SS (inches) 180 200 250 300
a
Minimum
6987
(275
1
/4)
7770
(306)
9727
(383
1
/8)
11685
(460)
Maximum
8404
(330
3
/4)
9344
(367
7
/8)
11694
(460
3
/8)
14044
(552
7
/8)
x
b+1130
(b+44
1
/2)
b+1255
(b+49
1
/2)
b+1569
(b+61
7
/8)
b+1883
(b+74
1
/4)
b
When using the PSS-610, adjustable with
243/268/293/343/368/393 mm
a
x
b
PSS-610 Projector Suspension
Support (not supplied)
Ceiling
Center of the
screen
Center of
the lens
Distance from the
front of the cabinet
and the center of the
lens
Standard lens
61.5 mm (2
1
/2 inches)
SS (inches) 80 100 120 150
a
Minimum
3741
(147
3
/8)
4692
(184
3
/4)
5642
(222
1
/8)
7067
(278
1
/2)
Maximum
4508
(177
5
/8)
5648
(222
1
/2)
6789
(267
3
/8)
8501
(334
3
/4)
x
b+609
(b+24)
b+762
(b+30)
b+914
(b+36)
b+1143
(b+45)
b
When using the PSS-610, adjustable with
243/268/293/343/368/393 mm
SS (inches) 180 200 250 300
a
Minimum
8493
(334
3
/8)
9443
(371
3
/4)
11819
(465
1
/2)
14195
(558
3
/4)
Maximum
10212
(402
1
/8)
11353
(447)
14205
(559
1
/8)
17057
(671
3
/4)
x
b+1371
(b+54)
b+1524
(b+60)
b+1905
(b+75)
b+2286
(b+90)
b
When using the PSS-610, adjustable with
243/268/293/343/368/393 mm
Step 2: Connecting the Projector
Connections and
Preparations
13
GB
Installation diagram
Top view
Align the center of the lens with the center of the
screen.
Front view
The lens is offset 7.9 mm (
5
/16 inch) to the right from
the center of the supporting pole. When mounting,
take care to align the center of the lens with the center
of the screen; not the center of the supporting pole.
Side view
Step 2:
Connecting the
Projector
When making connections, be sure to do the
following:
Turn off all equipment before making any
connections.
Use the proper cables for each connection.
Insert the cable plugs properly; plugs that are not
fully inserted often generate noise. When pulling
out a cable, be sure to pull it out from the plug, not
the cable itself.
Refer to the operating instructions of the connected
equipment.
When you connect your projector to PJ MULTI or
DVI connector, select the input signal with the
“Input-A Signal Sel.” or “Digital Signal Sel.
setting in the SET SETTING menu. (1 page
29)
Note
Before you change the “Digital Signal Sel.” setting, disconnect
the DVI cable and turn off the digital tuner, etc.
62.1
(2
1
/
2
)
61.5
(2
1
/
2
)
216.6
(8
5
/
8
)
134.2
(5
3
/
8
)
165
(6
1
/
2
)
7.9
(
5
/
16
)
Front of the cabinet
Center of the unit
Center of the lens
Center of the screen
Distance between the screen
and the center of the lens
Upper ceiling
mount bracket
Center of the supporting pole (The center of the
supporting pole is different from that of the unit.)
125 (5)
250 (9
7
/
8
)
165 (6
1
/
2
)
7.9 (
5
/
16
)
93.3
(3
3
/
4
)
Ceiling
The bottom
surface of the
mount
bracket
Center of the
supporting pole
Center of the lens
Center of the unit
Distance between the ceiling and the surface of
the mount bracket
Using adjustment pipe (b): 150/175/200 mm
(6 / 7 / 7
7
/8 inches)
Using adjustment pipe (c): 250/275/300 mm
(9
7
/8 / 10
7
/8 / 11
7
/8 inches)
134.2 (5
3
/
8
)
368.5 (14
5
/
8
)
216.6 (8
5
/
8
)
62.1
(2
1
/
2
)
61.5
(2
1
/
2
)
217.2 (8
5
/
8
)
234.3 (9
1
/
4
)
Front of the cabinet
Center of the lens
Unit: mm (inches)
Step 2: Connecting the Projector
Connections and
Preparations
GB
14
Connecting with Video
Equipment
Connecting a Digital Tuner
Using the DVI Connector
Connecting a DVD Player Equipped
With the Component Output
Connecting an AV Amplifier
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Rear of the projector
S video or
video cable
(not supplied)
to component
output
with SONY logo
upside
S
Video
Audio
amplifier
to S
video
or
video
output
R
L
L
R
Y
P
R/
C
R
Video equipment
Signal interface
cable (supplied)
P
B/
C
B
DVD player
Video
Active
speakers
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Rear of the projector
to DVI output
DVI cable (SMF-421, etc.,
not supplied)
Audio
amplifier
Active
speakers
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Audio
amplifier
Rear of the projector
Y
P
B/
C
B
PR/
C
R
PB/
C
B
PR/
C
R
Y
DVD player with component video
connectors, etc.
Active
speakers
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Signal interface cable
(supplied)
Rear of the projector
to component
video output
Y
P
B/
C
B
PR/
C
R
Video
S
Video
Active speakers
AV amplifier
to S Video or
Video output
Digital tuner, etc.
Step 2: Connecting the Projector
Connections and
Preparations
15
GB
Connecting a Computer
When connecting to an analog connector
To hear the sound from a computer, use the speakers
built in the computer or connect the active speakers to
the computer.
Note
Even if you connect the signal interface cable to the audio output
on the computer, there is no sound output from the projector.
When connecting to the DVI connector
Connecting Using the
Optional Interface Unit
Using the optional interface unit allows you to
connect various video equipment, and to select the
output to the projector or TV from the connected
equipment simply by switching the select switch on
the interface unit.
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Signal interface cable
(SIC-HS30, not supplied)
to monitor output
Active
speakers
Computer
Rear of the projector
S VIDEO
VIDEO
DVI
YP
B/CB PR/CR
PJ MULTI
INPUT
(FOR SERVICE USE)
Active
speakers
Rear of the projector
DVI cable (SMF-421, etc.,
not supplied)
Computer
to monitor
output
S VIDEO
VIDEO Y PB/CB PR/CR
PJ MULTI
INPUT
to PJ multi
output
Rear of the
projector
Interface unit
(IFU-HS1, not supplied)
VCR, etc.
DVD player, etc.
PJ multi cable (supplie
d
with the IFU-HS1)
Audio amplifier
Active
speakers
TV
Step 3: Adjusting the Picture Size and Position
Connections and
Preparations
GB
16
Step 3: Adjusting
the Picture Size
and Position
Tip
The ? /
1 (on/standby), INPUT, MENU, and m/M/</,/
ENTER (joystick) buttons on the side panel of the projector
function the same as those on the remote control.
1
Plug the AC power cord into a
wall outlet.
The ON/STANDBY indicator lights in red and
the projector goes into standby mode.
2
Press the [/1 (on/standby)
switch to turn on the projector.
The ON/STANDBY indicator lights in green.
3
Turn on the equipment
connected to the projector.
Refer to the operating instructions of the
connected equipment.
4
Press INPUT to project the
picture on the screen.
Each time you press the button, the input
indication changes. (1 page 21)
5
Adjust the focus roughly using
the FOCUS +/– button.
+
+
INPUTLIGHT
STANDARD
CINEMA
DYNAMIC
USER 2
PICTURE MODE
USER 3USER 1
MS SLIDE
MENUAPA
LENS
VOLUME SIDE SHOT
RESET
WIDE MODE
ENTER
6
5,7
Adjuster adjustment
button
Front remote control
detector
2
4
Rear remote control
detector
6
ON/
STANDBY
Lights in red.
ON/
STANDBY
Lights in green.
INPUT
NTSC 3.58
Video 1
FOCUS +/– button
Step 3: Adjusting the Picture Size and Position
Connections and
Preparations
17
GB
6
Adjust the size and position of
the picture to fit the screen.
When projecting using both “Side Shot” and
“V Keystone” adjustments
1 Use the adjuster to adjust the vertical
position.
If you set “V Keystone” in the INSTALL
SETTING menu to “Auto” (1 page 29), the
vertical distortion will be automatically corrected.
For how to use the adjuster, see “Using the
adjuster” on page 18.
Note
The “V Keystone” adjustment may not correct trapezoidal
distortion perfectly, depending on the room temperature or the
screen angle.
2 Adjust so that the left or right side of the
picture fits that of the screen.
If you position the projector on the left side of the
screen, adjust so that the left side of the picture fits
the left side of the screen. With the projector
positioned on the right side, adjust so that the right
side fits the right side of the screen.
At the same time, align the bottom side of the
picture with that of the screen.
3 Adjust to correct horizontal trapezoidal
distortion using the SIDE SHOT + or –
button.
Press SIDE SHOT + or – so that the upper side of
the picture becomes parallel to the bottom side. If
the left side is longer than the right side, press
SIDE SHOT –.
Press SIDE SHOT + if the right side is longer. To fine-
adjust the distortion, press M or m.
When projecting using “Side Shot”
adjustment only
1 Set “V Keystone” in the INSTALL SETTING
to “Manual,” and set the level to “0” (1
page 29) or press RESET.
2 Adjust so that the left or right side of the
picture fits that of the screen.
If you position the projector on the left side of the
screen, adjust so that the left side of the picture fits
the left side of the screen. With the projector
positioned on the right side, adjust so that the right
side fits the right side of the screen.
At the same time, adjust the vertical size of the
aligned side of the picture to fit the screen using
ZOOM +/–.
3 Adjust to correct horizontal trapezoidal
distortion using the SIDE SHOT + or –
button.
For how to correct, see step 3 in
When
projecting using both
Side Shot and V
Keystone adjustments.”
Picture
Screen
SIDE SHOT
Picture
Screen
Step 4: Selecting the Menu Language
Connections and
Preparations
GB
18
When projecting from the center
Adjust so that both the position and size of
the bottom side of the picture fit those of the
bottom side of the screen using the adjuster
and the ZOOM+/– button.
If you set “V Keystone” in the INSTALL SETTING
menu to “Auto” (1 page 29), the vertical distortion
will be automatically corrected.
For how to use the adjuster, see “Using the adjuster.
Note
The V Keystone adjustment may not correct trapezoidal distortion
perfectly, depending on the room temperature or the screen angle.
7
Press FOCUS +/– to adjust the
focus again.
Using the adjuster
Use the adjuster to adjust the picture position.
Lift the projector while pressing the adjuster
adjustment button, and release the button.
Holding the adjuster adjustment button pressed,
move the projector, then release the button at the
locked position.
Tip
When you press FOCUS +/– or ZOOM +/– in steps 5 to 7,
the built-in signal pattern is projected on the screen. If you
want to adjust the focus and picture size using the current
input signal, set “Test Pattern” in the INSTALL SETTING
menu to “Off.” (1 page 29)
Step 4:
Selecting the
Menu Language
You can select one of nine languages for displaying
the menu and other on-screen displays. The factory
default setting is English.
Tip
You can operate the menu using the joystick on the side panel of
the projector instead of the M/m/</,/ENTER buttons on the
remote control.
Picture
Screen
Adjuster
Adjuster
adjustment
button
+
+
INPUTLIGHT
STANDARD
CINEMA
DYNAMIC
USER 2
PICTURE MODE
USER 3USER 1
MS SLIDE
MENUAPA
LENS
VOLUME SIDE SHOT
RESET
WIDE MODE
ENTER
3
2
4
-
6
Step 4: Selecting the Menu Language
Connections and
Preparations
19
GB
1
Plug the AC power cord into a
wall outlet.
The ON/STANDBY indicator lights in red and
the projector goes into standby mode.
2
Press the [/1 (on/standby)
switch to turn on the projector.
The ON/STANDBY indicator lights in green.
3
Press MENU.
The menu appears.
The menu presently selected is shown as a
yellow button.
4
Press M or m to select the
MENU SETTING menu, and
press , or ENTER.
The selected menu appears.
5
Press M or m to select
“Language”, and press , or
ENTER.
6
Press M or m to select a
language, and press < or
ENTER.
The menu changes to the selected language.
To clear the menu
Press MENU.
MENU
Picture Mode Standard
Adjust Picture...
Volume: 30
PICTURE SETTING
Input A
ENTER
Input A
:
:
:
:
A
or
ENTER
MENU SETTING
Status:
Language:
Menu Position:
Menu Color:
Input A
or
ENTER
or
Projecting the Picture on the Screen
GB
20
Projecting
Projecting the
Picture on the
Screen
This section describes how to operate the
projector to view the picture from the
equipment connected to the projector. It
also describes how to select the wide
screen mode or the quality of the picture to
suit your taste.
+
+
INPUTLIGHT
STANDARD
CINEMA
DYNAMIC
USER 2
PICTURE MODE
USER 3USER 1
MS SLIDE
MENUAPA
LENS
VOLUME SIDE SHOT
RESET
WIDE MODE
ENTER
2
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208

Sony VPL-HS10 Manuel utilisateur

Catégorie
Projecteurs de données
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues