Extron TLSI 201 Manuel utilisateur

Marque: Extron

Modèle: TLSI 201

Taper: Manuel utilisateur

Product Category

IMPORTANT:

Go to for the

complete user guide and installation

instructions before connecting the

product to the power source.

TLSI 201 • Setup Guide

Overview

The Extron TLSI 201 Interactive Waynding Interface provides real-time meeting space availability, status, and location

information using a centralized display. The TLSI 201 communicates over the Ethernet network directly with Extron TLS

room scheduling panels and shows information about the Touchlink scheduler system on third-party touch and non-touch

displays. Users can locate and book meeting spaces for the day or week on an interactive grid or map with ease. No additional

programming or external processors are required.

This guide provides instructions for experienced installers to mount and install the TLSI 201 and to create a basic conguration.

For more complete instructions, see the TLSI 201 User Guide, at www.extron.com.

Setup Checklist

Get Ready

 Download and install the latest version of the following software:

 Room Agent™ — Room booking software for conguring the TLSI 201 for room scheduling. Room Agent can be

downloaded (free of charge) from www.extron.com.

 Obtain the following network information from your network administrator:

 DHCP status — (on or off). If DHCP is off, you must also obtain:

 IP address  Subnet mask  Gateway

 User name — This can be either admin or user.

 Password — The factory congured passwords for all accounts on this device have been set to the device serial

number. Passwords can be changed during conguration. They are case sensitive.

NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is extron

(for either admin or user).

 Make a note of the MAC address for the TLSI 201.

Mount and Cable All Devices

 Mount the units. The TLSI 201 can be discretely mounted behind a at panel display. Other mounting options are also

available (see the TLSI 201 product page at www.extron.com).

To mount the third-party touchpanel follow the instructions provided by the manufacturer.

 Connect cables to the TLSI 201 (see Rear Panel Connectors and Features on the next page).

 Connect the HDMI output from the TLSI 201 to the third-party touchpanel.

 Connect the USB port from the TLSI 201 to the third-party touchpanel.

NOTE: The USB connection passes information to the TLSI 201 about where on the screen the third-party touch

display was pressed. If using a non-touch display, connect a USB mouse to the USB port on the TLSI 201 to click

screen icons.

 Connect the Ethernet cable. The TLSI 201 must be powered by PoE+.

ATTENTION:

• Do not power on the TLSI 201 until you have read the Attention in the Rear Panel Features section of the TLSI 201

User Guide.

• Ne branchez pas le TLSI 201 avant d’avoir lu la mise en garde dans la section «Rear Panel Features» du TLSI 201

UserGuide.

Set up the TLSI 201 for Network Communication

 Connect the PC that you will use for setup on the same Ethernet subnetwork as the TLSI 201.

 Use the Setup Menu (see page 4) to set the DHCP status and, if necessary, the IP address, subnet mask, gateway, and

related settings for the network interface.

Conﬁgure the User Interface

Use Room Agent to congure the TLSI 201 (see the Room Agent User Guide and Room Agent Quick Start Guide at

www.extron.com, or the Room Agent Help File).

www.extron.com

TLSI 201 • Setup Guide (Continued)

Rear Panel Connectors and Features

For complete information about the rear panel connectors and features, see the TLSI 201 User Guide.

AAABBBC

CCD

DEVICE LAN/PoE

OUTPUTINPUT

Figure 1. TLSI 201 Rear Panel

ATTENTION:

• The TLSI 201 is Power over Ethernet (PoE 803.3at, class4) compliant. Do not connect the power supply before reading

the Attention in the Rear Panel Features section of the TLSI 201 User Guide.

• Le TLSI 201 support l’alimentation via Ethernet (PoE 803.3at, classe4). Veuillez lire la partie « Attention » dans la section

« Rear Panel Features » du TLSI 201 User Guide, avant de mettre sous tension les écrans tactiles.

HDMI input — At present, this port is not used by the TLSI 201.

HDMI output — Connect this female HDMI type A port to a third-party display. The TLSI 201 supports an output resolution

of 1080p.

gure 1

HDMI input

Use the provided LockIt HDMI lacing bracket to secure the HDMI connector:

1. Plug the HDMI cable into the TLSI 201 HDMI output port.

2. Loosen the HDMI connection mounting screw from the panel enough to

allow the LockIt lacing bracket to be placed over it. The screw does not

have to be removed.

3. Place the LockIt lacing bracket on the screw and against the HDMI

connector, then tighten the screw to secure the bracket.

ATTENTION:

• Do not overtighten the HDMI connection mounting screw. The

shield it fastens to is very thin and can easily be stripped.

• Ne serrez pas trop la vis de montage du connecteur HDMI. Le

blindage auquel elle est attachée est très n et peut facilement

être dénudé.

4. Loosely place the included tie wrap around the HDMI connector and the

LockIt lacing bracket as shown.

5. While holding the connector securely against the lacing bracket, tighten the

tie wrap, then remove any excess length.

Figure 2. Securing the HDMI Connector

DEVICE port — supports High-speed USB 2.0 control. Plug a Type-A USB cable from the third-party touchpanel into this

port.

NOTE: If using a non-touch display, connect a USB mouse to the USB port on the TLSI 201 to click screen icons.

LAN/PoE+ port — Use an Ethernet cable to connect this port to the network via a PoE+ power sourcing equipment (PSE,

not provided). This can be a power injector (see gure 3) or PoE+ switch.

NOTE: The TLSI 201 does not include any PoE+ power sourcing equipment. This must be purchased separately.

Extron recommends the Extron PI 140 power injector (see gure 3). Your power

injector may look different.

1. Use an Ethernet cable to connect the LAN/PoE+ port of the TLSI 201 to the

power output of the 803.3at, class4 compliant PoE+ power injector.

2. Connect the network input of the power injector to a network switch or router.

Alternatively, use an Ethernet cable to connect the LAN/PoE+ port of the TLSI 201 to

a PoE+ switch.

100-240V

50/60 Hz

1.1A MAX

INPUT

LAN POWERED TLP

OUTPUT

To network switch

To interface

Figure 3. PI 140 Power Injector

gure 3

Product Category

Front Panel Features

SIGNAL

INPUTOUTPUT

HDCP

TLSI 201

R MENU

AAABBBCCCDDD

Figure 4. TLSI 201 Front Panel

Power LED — Indicates the power status and the reset status of the unit.

Reset button (recessed) — allows the unit to be reset in any of three different modes. It also allows the user to toggle

between enabling and disabling the DHCP client. A brief summary of the reset modes is given below. For more information

see the TLSI 201 User Guide.

Menu button (recessed) — opens the Setup Menu (see the next page) and Calibration screen for the TLSI 201:

Setup Menu

1. Press the button briey (less than 3 seconds) to open the internal menu screens.

2. Press the button briey for a second time to exit the setup menu.

Calibration Screen

1. Press and hold the button (3 seconds or more) to open the Calibration screen. Follow the on-screen instructions to

calibrate the touchpanel.

2. Complete the calibration process or press the button briey (less than 2 seconds) for a second time to exit the

Calibration screen.

Status LEDs —

• The Signal LEDs light green when a video signal is detected and are unlit when no signal is detected.

• The HDCP LEDs light green when HDCP content is detected and are unlit when HDCP content is not detected.

Reset Modes: A Brief Summary

The TLSI 201 offers the following reset modes:

• Use Factory Firmware:

Press and hold the

Reset button (see ﬁgure 4,

, on page 3) while applying power to

the unit. Use this mode to replace rmware in the event of rmware failure.

• Reset All IP Settings:

Press and hold the

Reset button for 6 seconds. After the Power LED (

) ashes twice,

release and momentarily press the Reset button. Use this mode to reset all network

settings without affecting user-loaded les.

• Reset to Factory Defaults:

Press and hold the

Reset button for 9 seconds. After the Power LED ashes three times,

release and momentarily press the Reset button. Use this mode to return the device to

factory default settings.

NOTES:

• The factory congured passwords for all accounts on this device have been set to

the device serial number. Passwords can be changed during conguration. They

are case sensitive.

• If the device is reset to default settings, the passwords are reset to the default

password, which is extron (for either admin or user).

• Enable or Disable the DHCP

Client:

This mode toggles between DHCP enabled and DHCP disabled. Press the

Reset button

ve times, consecutively. After the fth press, do not press the button again within 3

seconds. If DHCP was enabled, it is now disabled and the Power LED blinks three times. If

DHCP was disabled, it is now enabled and the

Power LED blinks six times.

gure 4

68-3514-51 Rev. A

04 20

TLSI 201 • Setup Guide (Continued)

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Setup Menu

Press the Menu button (see ﬁgure 4,

) to open the setup menu (see

gure 5). There are ve available screens that are selected by pressing

the appropriate button in the navigation bar at the top of the screen.

• The Status screen is read-only and provides a summary of the

other screens.

• The Network screen is used to edit the network settings (DHCP

setting, IP, subnet mask and gateway addresses).

• The Display screen is used to congure the sleep timer.

• The Audio screen is used to set audio levels for the audible clicks

that accompany buttons being pressed on the display screen.

• The Advanced screen is used to set a PIN to prevent

unauthorized access to the setup menu. It is also used to

congure the mouse if the TLSI 201 is attached to a normal

display rather than a touchscreen.

Info

Model: TLSI 201

Part Number: 60-1669-01

Firmware

Version:

1.00

Network

IP Address:

DHCP:

Host Name:

Off

192.168.254.251

TLSI-AB-CD-EF

Display

Resolution:

Sleep Timer:

1920x1080

Off

Audio

Click Volume:

Click Mute: Off

Status

Display

Audio

Advanced

Exit

Network

Bootloader

Version:

1.00

Advanced

Menu PIN: Disabled

Figure 5. Setup Menu

Press the

Exit button to close the setup menu.

For more information about the setup menu, see the TLSI 201 User Guide at www.extron.com.

Extron TLSI 201 Manuel utilisateur

Marque: Extron

Modèle: TLSI 201

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Extron TLSI 201 User manual

Extron TLSI 201 Manuel utilisateur

Extron TLSI 201 Manuel utilisateur

dans d''autres langues

Documents connexes