Extron TLI Pro 201 Manuel utilisateur

TLI Pro 201
Extron
Marque
Extron
Modèle
TLI Pro 201
Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur

Ce manuel convient également à

1
Product Category
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
TLI Pro 201 and TLSI 201 • Setup Guide
Overview
The Extron TLI Pro 201 is a TouchLink
®
Interface scaler that integrates a third-party touchscreen display as a point of control
within an Extron Pro series control system. The scaled output supports resolutions up to 4K @ 30 Hz. The Extron TLI Pro 201
provides annotation features that allow users to draw, point, or type on video sources during presentations.
The TLSI 201 is a display interface that centralizes information about the TouchLink scheduler system.
This guide provides instructions for experienced installers to mount and install the TLIPro 201 or TLSI 201 and to create a basic
conguration. For more complete instructions, see the TLI Pro 201 and TLSI 201 User Guide, at www.extron.com.
Setup Checklist
Get Ready
Download and install the latest version of the following software:
Toolbelt — Provides device discovery, device information, rmware updates, and conguration of network settings,
system utilities, and user management for TouchLink Pro devices.
TLI Pro 201
GUI Designer — For designing layouts for third party touchpanel interfaces.
Global Configurator
®
Professional and Global Configurator Plus — For setting up and conguring the control
processor and interface.
Global Scripter
®
— Provides an integrated development environment for Extron control systems programming.
TLSI 201
Room Agent™ — Room booking software for conguring the TLSI 201 for room scheduling.
NOTE: All ve software programs are available from www.extron.com.
Obtain the following network information from your network administrator:
DHCP status — (on or off). If DHCP is off, you must also obtain:
IP address Subnet mask Gateway
User name — This can be either admin or user.
Password — The factory congured passwords for all accounts on this device have been set to the device serial
number. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the password will be the default password conguration. The default
password is extron (for either admin or user).
Make a note of the interface MAC address.
Mount and Cable All Devices
Mount the units. Place the interface on a convenient surface, mount it in a standard rack, or use an under-table mounting
kit (see the TLI Pro 201 and TLSI 201 User Guide, at www.extron.com). To mount the third-party touchpanel follow the
instructions provided by the manufacturer.
Connect cables to the interface (see Rear Panel Connectors and Features on the next page).
Connect the required HDMI source to the HDMI input (TLI Pro 201 only).
Connect the HDMI output from the interface to the third-party touchpanel.
Connect the USB port from the interface to the third-party touchpanel.
NOTE: The USB connection passes information to the interface about where on the screen the touchpanel was
pressed. To use a normal monitor, instead of a touchscreen, connect a mouse to the USB connection. Use the
mouse to click on screen icons.
www.extron.com
TLI Pro 201 and TLSI 201 • Setup Guide (Continued)
Connect the Ethernet cable. The interface must be powered by PoE+.
ATTENTION:
• Do not power on the TLI Pro 201 or TLSI 201 until you have read the Attention in the Rear Panel Features section of
the TLI Pro 201 User Guide.
• Ne branchez pas le TLI Pro 201 ou le TLSI 201 avant d’avoir lu la mise en garde dans la section «Rear Panel
Features» du TLI Pro 201 UserGuide.
Set up the Interface for Network Communication
Connect the PC that you will use for setup on the same Ethernet subnetwork as the interface. If you are using the
TLI Pro 201, you must also connect a control processor to the same subnetwork. The TLSI 201 does not require a control
processor.
Use the Setup Menu (see page 4) or Toolbelt to set the DHCP status and, if necessary, the IP address, subnet mask,
gateway, and related settings for the network interface.
Configure the User Interface
TLI Pro 201 — The Global Configurator Professional Help File, the Global Configurator Plus Help File, and the GUI Designer
Help File provide step-by-step instructions and more detailed information. The Global Congurator Professional and Global
Congurator Plus help les include an introduction to the software and sections on how to start a project and conguration.
TLSI 201 — Use Room Agent to congure the TLS touchpanels. For complete instructions about conguring the TLSI 201, see
the Room Agent Help File, User Guide, and Quick Start Guide at www.extron.com.
Rear Panel Connectors and Features
The TLI Pro 201 and TLSI 201 have identical rear panels. For complete information about the rear panel connectors and features,
see the TLI Pro 201 and TLSI 201 User Guide.
AAABBBC
CCD
DD
USB LAN/PoE
+
OUTPUTINPUT
Figure 1. TLI Pro 201 Rear Panel
ATTENTION:
• The TLI Pro 201 and TLSI 201 are Power over Ethernet (PoE 803.3at, class4) compliant. Do not connect the power
supply before reading the Attention in the Rear Panel Features section of the TLI Pro 201 and TLSI 201 User Guide.
• Le TLI Pro 201 et le TLSI 201 supportent l’alimentation via Ethernet (PoE 803.3at, classe4). Veuillez lire la partie
« Attention » dans la section « Rear Panel Features » du TLI Pro 201 and TLSI 201 User Guide, avant de mettre sous
tension les écrans tactiles.
gure 1
A
HDMI input (TLI Pro 201 only) — Plug the cable from the input source device
into this female HDMI type A port. Use the provided LockIt HDMI lacing bracket
to secure the HDMI connector:
1. Plug the HDMI cable into the panel connection.
2. Loosen the HDMI connection mounting screw from the panel enough to
allow the LockIt lacing bracket to be placed over it. The screw does not
have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI
connector, then tighten the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connection mounting screw. The
shield it fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le
blindage auquel elle est attachée est très n et peut facilement
être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the
LockIt lacing bracket as shown.
5. While holding the connector securely against the lacing bracket, tighten the
tie wrap, then remove any excess length.
HDMI input
3
1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
Figure 2. Securing the HDMI Connector
3
Product Category
B
HDMI output (see figure 1 on the previous page) — Connect this female HDMI type A port to a third-party touch screen. A
full list of compatible resolutions is provided in the TLI Pro 201 and TLSI 201 User Guide.
Use the provided LockIt brackets to secure the connector to the TLI Pro 201 or TLSI 201 unit (see HDMI input, on the
previous page).
C
USB port — supports High-speed USB 2.0 control. Plug a Type-A USB cable from the third-party touchpanel into this port.
NOTE: To use a monitor that is not a touchpanel, connect a mouse to this port.
D
LAN and PoE+ port — Use an Ethernet cable to connect this port to the network via a PoE+ power sourcing equipment
(PSE, not provided). This can be a power injector (see gure 3) or PoE+ switch.
NOTE: These interfaces are shipped without a PoE+ PSE. This must be purchased separately.
Front Panel Features
A
A
AB
B
BC
C
CD
D
D
SIGNAL
INPUTOUTPUT
HDCP
TLI Pro 201
R MENU
Figure 4. TLI Pro 201 Front Panel
A
Power LED — Indicates the power status and the reset status of the unit.
B
Reset button (recessed) — allows the unit to be reset in any of three different modes. It also allows the user to toggle
between enabling and disabling the DHCP client. A brief summary of the reset modes is given below. For more information
see the TLI Pro 201 and TLSI 201 User Guide.
C
Menu button (recessed) — opens the Setup Menu (see the next page) and Calibration screen for the interface:
• Press the button briey (less than 2 seconds) to open the internal menu screens.
• Press and hold the button (at least 2 seconds) to open the Calibration screen. Follow the on-screen instructions to
calibrate the touchpanel.
• Press the button briey (less than 2 seconds) for a second time to close the current screen without saving any changes.
D
Status LEDs —
• The Signal LEDs light green when a video signal is detected and are unlit when no signal is detected.
• The HDCP LEDs light green when HDCP content is detected and are unlit when HDCP content is not detected.
100-240V
50/60 Hz
1.1A MAX
INPUT
LAN POWERED TLP
OUTPUT
To network switch
To interface
Figure 3. PI 140 Power Injector
gure 3
Extron recommends the Extron PI 140 power injector (see gure 3). Your power
injector may look different.
1. Use an Ethernet cable to connect the LAN/PoE+ port of the interface to the
power output of the 803.3at, class4 compliant PoE+ power injector.
2. Connect the network input of the power injector to a network switch or router.
Alternatively, use an Ethernet cable to connect the LAN/PoE+ port of the interface to
a PoE+ switch.
4
68-3514-50 Rev. A
02 20
TLI Pro 201 and TLSI 201 • Setup Guide (Continued)
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Reset Modes: a Brief Summary
The TLI Pro 201 and TLSI 201 offer the following reset modes:
• Use factory firmware:
Press and hold the Reset button (Figure 4,
B
) while applying power to the unit. Use this
mode to replace rmware in the event of rmware failure.
• Reset All IP Settings:
Press and hold the Reset button for 6 seconds. After the Power LED (Figure4,
A
) ashes
twice, release and momentarily press the Reset button. Use this mode to reset all network
settings without affecting user-loaded les.
• Reset to Factory Defaults:
Press and hold the Reset button for 9 seconds. After the Power LED ashes three times,
release and momentarily press the Reset button. Use this mode to return the device to
factory default settings.
NOTES:
• The factory congured passwords for all accounts on this device have been set to
the device serial number. Passwords are case sensitive.
• If the device is reset to default settings, the password is the default password
conguration. The default password is extron.
• Enable or Disable the DHCP
Client:
This mode toggles between DHCP enabled and DHCP disabled. Press the Reset button
ve times, consecutively. After the fth press, do not press the button again within 3
seconds. If DHCP was enabled, it is now disabled and the Power LED blinks three times. If
DHCP was disabled, it is now enabled and the Power LED blinks six times.
Setup Menu
Press the Menu button (see Front Panel Features,
C
on page 3)
to open the setup menu (see gure 5). There are six available screens
that are selected by pressing the appropriate button in the navigation
bar at the top of the screen.
• The Status screen is read-only and provides a summary of the
other screens.
• The Network screen is used to edit the network settings (DHCP
setting, IP, subnet mask and gateway addresses).
• The Output screen is used to congure the image shown by the
third-party display, using built-in test patterns and EDID.
• The Audio screen is used to set audio levels.
• The Input screen is used to congure the input video signal.
• The Advanced screen provides information about the system and
the GUI project
Info
Model: TLI Pro 201
Part Number: 60-1669-01
Firmware
Version:
1.00
Network
IP Address:
DHCP:
Host Name:
Off
192.168.254.251
TLI-AB-CD-EF
Output
TLI Output:
GUI Project:
Sleep Timer:
1080p @ 60Hz
1080p @ 60Hz
5 Minutes
Audio
Master Volume:
Master Mute: Off
99
Input
HDMI: No Signal
Status
Output
Audio
Advanced
Exit
Network
Input
Advanced
Controller IP: 192.168.254.250
Project Size: N/A
Bootloader
Version:
1.00
PoE Status:Active
Figure 5. Setup Menu
Press the Exit button to close the setup menu.
For more information about the setup menu, see the TLI Pro 201 and TLSI 201 User Guide at www.extron.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron TLI Pro 201 Manuel utilisateur

TLI Pro 201
Extron
Marque
Extron
Modèle
TLI Pro 201
Catégorie
Commutateurs vidéo
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents