Ryobi RY908000E Le manuel du propriétaire

Marque: Ryobi

Modèle: RY908000E

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

NEUTRAL BONDED TO FRAME

CONNECTEUR NEUTRE LIBRE

PUNTO NEUTRO CONECTADO AL MARCO

WARNING: To reduce the risk of

injury, the user must read and understand

the operator’s manual before using this

product.

TABLE OF CONTENTS

 Important Safety Instructions ............3-4

 Specific Safety Rules ...........................4

 Symbols ............................................5-7

 Electrical ...........................................8-9

 Features .............................................10

 Assembly ......................................11-12

 Operation ......................................13-15

 Maintenance .................................16-19

 Troubleshooting .................................20

 Parts Ordering/Service ......... Back Page

AVERTISSEMENT : Pour

réduire les risques de blessures,

l’utilisateur doit lire et veiller à bien

comprendre le manuel d’utilisation avant

d’employer ce produit.

ADVERTENCIA : Para

reducir el riesgo de lesiones, el

usuario debe leer y comprender el

manual del operador antes de usar

este producto.

TABLE DES MATIÈRES

 Instructions importantes

concernant la sécurité ......................3-4

 Règles de sécurité particulières ........... 4

 Symboles ..........................................5-7

 Caractéristiques électriques .............8-9

 Caractéristiques ................................. 10

 Assemblage ..................................11-12

 Utilisation ......................................13-16

 Entretien ........................................17-20

 Dépannage .........................................21

 Commande de pièces /

réparation ............................Páge arrière

ÍNDICE DE CONTENIDO

 Instrucciones de seguridad

importantes .......................................3-4

 Reglas de seguridad específicas ......... 4

 Símbolos ...........................................5-7

 Aspectos eléctricos ..........................8-9

 Características ...................................10

 Armado .........................................11-12

 Funcionamiento ............................13-16

 Mantenimiento ..............................17-20

 Corrección de problemas ..................21

 Pedidos de piezas/

servicio ............................ Pág. posterior

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

8,000 WATT GENERATOR

GÉNÉRATRICE DE 8 000 WATTS

GENERADOR 8 000 WATTS

RY908000E

SAVE THIS MANUAL FOR

FUTURE REFERENCE

CONSERVER CE MANUEL

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL

PARA FUTURAS CONSULTAS

NOTICE AVIS AVISO

Do not use E15 or E85 fuel in this

product. It is a violation of federal law

and will damage the unit and void your

warranty. Only use unleaded gasoline

containing up to 10% ethanol.

Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une

telle utilisation représente une violation de la loi fédérale

et endommagera l’appareil et annulera la garantie. Utiliser

seulement de l’essence sans plomb ne contenant pas plus

de 10 % d’éthanol.

No utilice combustibles E15 o E85 con este producto. Esto

constituye una violación a la ley federal, dañará la unidad y

anulará la garantía. Utilice únicamente gasolina sin plomo

que contiene hasta 10% de etanol.

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les figures

mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras

a las que se hace referencia en el manual del operador.

Fig. 2

G - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

H - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

I - Engine switch / fuel valve / choke lever

(interrupteur du moteur / robinet de

carburant / levier d’étrangleur, interruptor

del motor/válvula de combustible/palanca

del anegador)

J - Recoil starter grip (poignée du démarreur à

rappel, mango del arrancador retráctil)

K - Air filter (filtre à air, filtro de aire)

L - Digital display (affichage numérique, pantalla

digital)

M - Circuit breakers (disjoncteurs, disyuntors)

N - Handle (poignée, mango)

- Ground terminal (borne de terre, terminal de

conexión a tierra)

P - Muffler (silencieux, silenciador)

Q - Fuel tank vapor vent (évent de vapeur du

réservoir de carburant, respirador del vapor

del tanque de combustible)

R - Battery (batterie, batería)

S - Start button ((bouton démarrage, botón de

arranque)

T - Run switch (interrupteur de marche,

interruptor de encendido)

A - Handle release knob (bouton de verrouillage

de la poignée, perilla de liberación del

mango)

B - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

D - 120 volt AC 20 amp GFCI receptacles (prises

de fuite à la terre 120 V c.a. 20 A, 120 V de

CA 20 A receptáculos con GFCI)

E - 240 volt AC 30 amp twist lock receptacle

(prise à verrouillage par rotation de 240 volt

c.a. 30 A, 240 V de ca 30 A receptáculo de

bloqueo por giro)

F - Wheel (roue, rueda)

Fig. 1

A - Reset button (bouton de

réinitialisation, botón de

reajuste)

B - Test button (bouton de

test, botón de prueba)

iii

Fig. 4

Fig. 5

Fig. 6

A - Socket wrench (clé à douille, llave de casquillo)

B - Adjustable wrench (clé à molette, llave ajustable)

C - Phillips screwdriver (tournevis cruciforme, destornillador Phillips)

Fig. 3

A - Bolt (boulon, perno)

B - Cross brace (renfort transversal, través del

travesaño)

C - Rubber foot (pied en caoutchouc, pie de

goma)

D - Lock nut (écrou frein, tuerca de bloqueo)

Fig. 8

A - Handle (poignée, mango)

B - Handle release knob (bouton de verrouillage

de la poignée, perilla de liberación del mango)

C - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

A - Axle (essieu, eje)

B - Wheel (roué, rueda)

C - Washer (rondelle, arandela)

D - Mounting hole (trou de montage, agujero de

montaje)

E - Hitch pin (axe de blocage, pasador del

enganche)

Fig. 9

A - Oil cap/dipstick (capuchon d’huile/la jauge,

tapa de relleno de aceite / varilla medidora de

aceite)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

A - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

B - Fuel tank (réservoir de carburant, tanque de

combustible)

Fig. 10

A - Battery bracket (support de batterie, soporte

de la batería)

B - Positive (+) terminal [borne positive (+), tapa

del terminal positiva (+)]

C - Negative (–) terminal [borne négative (–),

terminal negativa (–)]

D - Black wire (–) [fil noir (–) cable negro (–)]

E - Screw (vis, tornillo)

F - Washer (rondelle, arandela)

G - Nut (écrou, tuerca)

H - Red wire (+) [fil rouge (+), cable rojo (+)]

Fig. 7

A - Engine switch / fuel valve / choke lever in OFF

position (interrupteur du moteur / robinet

de carburant / levier d’étrangleur en position

ARRET, interruptor del motor/válvula de

combustible/palanca del anegador en la

posición APAGADO)

B - START (DÉMARRAGE, ARRANQUE)

C - RUN (MARCHE, MARCHA)

D - Run switch (interrupteur de marche,

interruptor de encendido)

A - Recoil starter grip (poignée de démarreur à

rappel, mango del arrancador retráctil)

A - Knob (bouton, perilla)

B - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

C - Filter element (élément du filter, elemento de

filtro)

D - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

Fig. 17

Fig. 15

Fig. 12

Fig. 14

Fig. 16

Mode

Fig. 11

A - Digital display (affichage numérique, pantalla

digital)

B - Mode button (bouton « mode », botón mode)

A - Start button (bouton démarrage, botón de

arranque)

Fig. 13

A - Spark plug (bougie, bujía)

B - Spark plug cap (capuchon de bougie, tapa

de la bujía)

A - Spark arrestor (pare-étincelle, parachispas)

Fig. 19

Fig. 20

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Oil cap/dipstick (bouchon / jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

Fig. 18

A - Fuel line (conduite de carburant, conducto de

combustible)

B - Fuel filter (filtre de carburant, filtro de

combustible)

Fig. 24

A - Engine switch / fuel valve / choke lever

(interrupteur du moteur / robinet de

carburant / levier d’étrangleur, interruptor del

motor/válvula de combustible/palanca del

anegador)

B - Hose barb (raccord à tuyau cannelé, conector

de manguera dentada)

C - Fuel line (conduite de carburant, conducto de

combustible)

Fig. 21

A - Carburetor drain screw (vis de vidange

du carburateur, tornillo de drenaje del

carburador)

A - Drain line (not provided) [tuyau de vidange

(non fourni), conducto de drenaje (no

incluido)]

B - RUN position (position RUN [MARCHE],

posición RUN [MARCHA])

Fig. 23

Fig. 22

Fig. 25

A - Fuse holder (porte-fusible, sujetador de la

fusible)

B - Fuse (fusible, fusible)

Page 2 — English

KEEP AT LEAST

20 FT. AWAY

CO Detector

in Living Areas

Only use OUTSIDE and

FAR AWAY from windows,

doors, and vents.

Exhaust (CO)

Direct exhaust AWAY

from all windows, doors,

and vents.

LOCATE GENERATOR AT LEAST 20 FT.* AWAY TO REDUCE THE

RISK OF CARBON MONOXIDE GETTING INSIDE THE HOME

* Minimum distance as recommended by U.S. Department of Health and Human

Services Centers for Disease Control and Prevention (www.cdc.gov/co). Your specific

home and/or wind conditions may require additional distance.

To register your Ryobi product,

please visit: www.ryobitools.com

WARNING:

GROUNDING THE GENERATOR

If this generator will be used only with cord and plug-connected equipment,

National Electric Code does not require that the unit be grounded. However,

other methods of using the generator may require grounding to reduce the risk

of shock or electrocution. Consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or ordinances to find out if

grounding is needed in your situation before using the generator.

When grounding is required, the nut and ground terminal on the frame are used

to connect the generator to a suitable ground source. The ground path should

be made with #8 size wire. Connect the terminal of the ground wire between

the lock washer and the nut, and tighten the nut fully. Connect the other end of

the wire securely to a suitable ground source that is in contact with the soil for

a minimum distance of 8 ft.

The National Electric Code contains several practical ways in which to establish a good ground source. If a steel or

iron rod is used, it should be at least 5/8 in. diameter, and if a nonferrous rod is used, it should be at least 1/2 in. di-

ameter and be listed as material for grounding. If a rock bottom is encountered before reaching a depth of 8 ft., drive

the ground rod in at an angle of up to 45°. If the rock bottom is again encountered, the rod can be buried in a trench

that is at least 30 in. deep. In all cases, the upper end of the grounding rod should either be flush with (or below) the

ground or must be otherwise protected from physical damage.

All electrical tools and appliances operated from this generator must be properly grounded by use of a third wire or

be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

WARNING:

In some applications, National Electric Code requires

generator to be grounded to an approved earth ground.

Before using the ground terminal, consult a qualified

electrician, electrical inspector, or local agency having

jurisdiction for local codes or ordinances that apply to

the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be

followed during installation and maintenance of the genera-

tor and batteries.

Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

Do not allow children or untrained individuals to use this

unit.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

Keep all bystanders, children, and pets at least 10 feet

away.

Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

Do not touch bare wire or receptacles.

Do not use generator with electrical cords which are worn,

frayed, bare, or otherwise damaged.

Before storing, allow the engine to cool for 30 minutes

and drain fuel from the unit.

Do not operate or store the generator in rain, snow, or

wet weather.

Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

Empty fuel tank, place the engine switch/fuel valve/choke

lever in the OFF position, and restrain the unit from mov-

ing before transporting in a vehicle.

Provide a plastic sheet or absorbent pad below the

generator to catch any drips of fuel or lubricant when

transporting.

To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

Do not smoke while handling fuel.

Store fuel in a container approved for gasoline.

Position the unit on level ground, stop engine, and allow

to cool for five minutes before refueling.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Tighten the fuel cap securely after refueling.

Wipe spilled fuel from the unit.

Never attempt to burn off spilled fuel under any circum-

stances.

Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

Page 4 — English

IMPORTANT SAFETY INSTRUCTIONS

For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Use only recommended or equivalent replacement

parts and accessories and follow instructions in the

Maintenance section of this manual. Use of any other

parts or failure to follow maintenance instructions may

create a risk of shock or injury.

Maintain the unit per maintenance instructions in this

Operator’s Manual.

Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

DANGER:

Risk of fire and serious burns: Never remove fuel cap

when unit is running. Shut off engine and allow the unit

to cool at least five minutes. Remove cap slowly.

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

Do not use this generator to provide power for emergency

medical equipment or life support devices.

This generator has a neutral bonded condition. This

means the neutral conductor is electrically connected to

the frame of the machine.





Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.





Place the generator on a flat, stable surface with a slope

of no more than 4°.





Operate outdoors in a well-ventilated, well-lit area isolated

from working areas to avoid noise interference.





Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.





Keep the generator a minimum of 3 feet away from all

types of combustible material.





Do not operate generator near hazardous material.





Do not operate generator at a gas or natural gas filling

station.





Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.



Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.





Do not smoke when filling the generator with gasoline.





Shut down the engine and allow to cool for five minutes

before adding gasoline or lubricant to the generator.





Do not remove the oil dipstick or the fuel tank cap when

the engine is running.





Pay close attention to all safety labels located on the

generator.





Keep children a minimum of 10 feet away from the gen-

erator at all times.





The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.





Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from the

generator name plate ratings. To avoid damage, always

have an additional load plugged into the generator if

solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

When battery is not in use, keep it away from other metal

objects like paper clips, coins, keys, nails, screws, or other

small metal objects that can make a connection from one

terminal to another. Shorting the battery terminals together

may cause burns or a fire.



For outdoor use only.





Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

SPECIFIC SAFETY RULES

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion

Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface and Exhaust

Gases

To reduce the risk of injury or damage, avoid contact with any

hot surface and do not place any body parts in the path of hot

exhaust gases.

Lifting Hazard

To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground

Consult with local electrician to determine grounding requirements

before operation.

Recycle Symbol

This product uses lead acid (Pb) batteries. Local, state or federal

laws may prohibit disposal of batteries in ordinary trash. Consult

your local waste authority for information regarding available re-

cycling and/or disposal options.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates a hazardous situation, which, if not avoided, will result in death or

serious injury.

WARNING:

Indicates a hazardous situation, which, if not avoided, could result in death or

serious injury.

CAUTION:

Indicates a hazardous situation, that, if not avoided, may result in minor or

moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates information considered important, but

not related to a potential injury (e.g. messages relating to property damage).

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

V Volts Voltage

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

DANGER

PELIGRO

L’utilisation d’une génératrice à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES.

Les génératrices produisent du monoxyde de carbone, un gaz mortel incolore et inodore.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un garage,MÊME SI les portes et

les fenêtres sont ouvertes.

Utiliser uniquement À L’EXTÉRIEUR et loin des fenêtres, des portes et des évents.

Usar un generador en el interior PUEDE MATARLO EN POCOS MINUTOS.

Los gases de escape del generador contienen monóxido de carbono. Es un veneno

que no puede verse ni olerse.

NUNCA lo use dentro de su hogar o del garaje, INCLUSO con las puertas y las

ventanas abiertas.

Sólo utilícelo AL AIRE LIBRE y lejos de ventanas, puertas y respiraderos.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

You WILL be KILLED or SERIOUSLY HURT if you do not follow the

Operator’s Manual instructions.

Ne pas procéder de la manière décrite dans ce Manuel

d’utilisation entraînera des BLESSURES GRAVES voire

la MORT.

SE MATARÁ o LESIONARÁ GRAVEMENTE si no sigue las

instrucciones del Manual del operador.

Exhaust contains poisonous carbon monoxide gas that can cause unconsciousness or

DEATH. Operate in well ventilated, outdoor areas away from open windows or doors.

L’échappement contient le gaz monoxyde de carbone toxique qui peut causer

l’inconscience ou la MORT. Fonctionner dans les secteurs bien ventilés et extérieurs

loin d’ouvre des fenêtres ou des portes.

El escape contiene gas venenoso de monóxido de carbono que puede causar pérdida del

conocimiento o MUERTE. Opere en áreas exteriores bien ventiladaslejos de puertas o ventanas

abiertas.

Risk of fire. Do not add fuel while the

product is operating.

Risque d’incendie. Ne pas ajouter de carburant

pendant l’utilisation de l’appareil.

Riesgo del incendio. No agregue combustible

cuando el producto esté functionando.

Generator is a potential source of electric shock. Do not expose

to moisture, rain, or snow. Do not operate with wet hands or feet.

Le générateur est une source potentielle de chocs électriques. Ne

pas exposer à l’humidité, la pluie ou la neige. Ne pas utiliser avec

les mains ou les pieds mouillés.

El generador es una fuente de descarga eléctrica. No lo exponga a

humedad, la lluvia, nin a la nieve. No opere con manos o pies húmedos.

Do not expose to rain or

use in damp locations.

Ne pas exposer à la pluie

ou l’humidité.

No exponga a la lluvia

ni use en lugares

húmedos.

940654359-01

DANGER

PELIGRO

DANGER

SAFETY LABELS

The information below can be found on

the generator. For your safety, please

study and understand all of the labels

before starting the generator.

If any of the labels come off the unit or

become hard to read, contact customer

service or a qualifed service center for

replacement.

You WILL be KILLED or SERIOUSLY HURT if you do not

follow the Operator’s Manual instructions.

Risk of Fire. Do not add fuel while the product is operating.

Generator is a potential source of electric shock. Do not

expose to moisture, rain, or snow. Do not operate with

wet hands or feet.

Exhaust contains poisonous carbon monoxide gas that

can cause unconsciousness or DEATH. Operate in well-

ventilated, outdoor areas away from open windows or

doors.

Do not expose to rain or use in damp locations.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home or garage, EVEN IF doors and

windows are open.

Only use OUTSIDE and far away from windows, doors,

and vents.

Page 7 — English

FUEL CAP WARNING

Never remove fuel cap when unit is run-

ning. Shut off engine and allow the unit

to cool at least five minutes. Remove

cap slowly to release any pressure built

up in the fuel system and to avoid the

heat from the muffler igniting fuel vapors.

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below the

top of the fuel neck. Stop the engine for

five minutes before refueling to avoid the

heat from the muffler igniting fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first

operating the generator. Always check

the lubricant level before each opera-

tion. The lubricant level should always

the dipstick. The unit is equipped with

a sensor which will automatically shut

off the engine if the lubricant level falls

below a safe limit.

GROUNDING WARNING

This generator does not include a ground

rod or copper wire. Call a qualified elec-

trician for local grounding requirements.

SPARK ARRESTOR

Operation of this equipment may create

sparks that can start fires around dry

vegetation. A spark arrestor may be re-

quired. The operator should contact lo-

cal fire agencies for laws or regulations

relating to fire prevention requirements.

HOT SURFACE WARNING

Do not touch the muffler or aluminum

cylinder of the engine. They are very

HOT and will cause severe burns. Don’t

put body parts or any flammable or

combustible materials in the direct path

of the exhaust.

CLEARANCE WARNING

While operating and storing, keep at

least 3 feet of clearance on all sides of

this product, including overhead. Al-

low a minimum of 30 minutes of “cool

down” time before storage. Heat creat-

ed by muffler and exhaust gases could

be hot enough to cause serious burns

and/or ignite combustible objects.

SYMBOLS

940513029-02

Product does not include ground rod or copper wire. Call a qualified electrician for local

grounding requirements.

Le produit ne comprend pas de piquet de terre ou de fil en cuivre. Appeler un électricien qualifié

pour connaître les exigences locales de mise à la terre.

El producto no incluye el ealambre de cobre ni la barra de conexión a tierra. Comuniquese con un

electrista calificado para todo lo relacionado con los requistos de conexión a tierra.

SURFACE ET D’ECHAPPEMENT CHAUDS

SUPERFICIE Y DE ESCAPE ESTEN CALIENTE

HOT SURFACE AND EXHAUST

AVERTISSEMENTWARNING ADVERTENCIA

940680075-01

CHECK LUBRICANT

Add lubricant to full mark to start. Engine will not start or will shut off if sensor detects

low lubricant level. • Ajouter de lubrifiant jusqu’au repère de remplissage pour

dèmarrer. Le moteur ne démarre pas ou s’éteint si le capteur détecte le niveau de

lubrifiant faible. • Añada lubricante hasta la marca de ileno para arrancar. El motor no

arranca o se apaga si sensor detecta el nivel de lubricante de baja.

NOTICE AVIS AVISO

940708019-04

Risk of Fire. Check for any fuel overflow or leaking. Stop the engine before refueling.

DANGERDANGER PELIGRO

Risque d’incendie. Vérifier l'absence de débordement ou de fuite de carburant.

Arrêter le moteur avant de fair le plein.

Riesgo de incendio. Revise si hay algún derrame o fuga de combustible. Apague el

motor antes de poner combustible.

940974007-05

DANGERDANGER PELIGRO

940974089-04

Risk of Fire. Keep all objects at least 3 feet away from this machine. Heat from Muffler and Exhaust gases

can ignite combustible objects.

Risque d’incendie. Éloigner tous les objets au moins de 91,4 cm (3 pi) de cet appareil. La chaleur

du pot d’échappement et les gaz d’échappement peuvent enflammer les objets combustibles.

Riesgo de incendio. Mantener todos los objetos a una distancia mínima de 91,4 cm (3 pies) de esta

máquina. El calor de los gases del silenciador y el escape pueden prender fuego a objetos combustibles.

DANGER

RISK OF FIRE AND SERIOUS BURNS:

Never remove fuel cap when unit is

running. Shut off engine and allow

the unit to cool at least five minutes.

Remove cap slowly.

RISQUE D'INCENDIE ET DE BLESSURES GRAVES : Ne jamais retirer le

capuchon du réservoir d'essence pendant que l'appareil fonctionne.

Éteindre le moteur et laisser refroidir l'appareil pendant au moins

cinq minutes. Retirer lentement le capuchon.

EL USO DEL ESTABILIZADOR DE COMBUSTIBLE PARA EL ALMANCENAMEIENTO

UTILISEZ UN STABILISATEUR DE CARBURANT POUR LE STOCKAGE

RIESGO DE INCENDIOS Y LESIONES POR QUEMADURAS: Nunca retire la tapa

de combustible mientras esté encendida la unidad. Apague el motor y deje

enfriar la unidad durante al menos cinco minutos. Retire la tapa lentamente.

DANGER PELIGRO

L’utilisation de cet équipement peut créer des étincelles susceptibles d’enflammer la

végétation sèche. Il peut être nécessaire d’utiliser un pare-étincelles. L’utilisateur doit

communiquer avec le service local d’incendie pour connaître toutes les lois et tous les règlements portant sur les

exigences en matière de prévention des incendies.

Operation of

this equipment may create

sparks that can start fires around dry vegetation. A spark arrestor may

be required. The operator should contact local fire agencies for laws or regulations

relating to fire prevention requirements.

WARNING

AVERTISSEMENT

ADVERTENCIA

El uso de este equipo puede producir chispas propensas a iniciar incendios cerca de

vegetación seca. Es posible que se necesite un parachispas. El operador debe ponerse en

contacto con las agencias contra incendios locales para conocer las leyes y regulaciones relacionadas con los

requisitos de prevención de incendios.

Page 8 — English

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts

Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450 950 1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

NOTICE:

Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

GROUND FAULT CIRCUIT INTERRUPTER

See Figure 1.

The 20 amp, 120 volt receptacles on the generator are

protected by a Ground Fault Circuit Interrupter (GFCI),

which guards against the hazards of ground fault currents.

ELECTRICAL

An example of ground fault current is the current that would

flow through a person who is using an appliance with faulty

insulation and, at the same time, is in contact with an electrical

ground such as a plumbing fixture, wet floor, or earth.

GFCI receptacles do not protect against short circuits,

overloads, or shocks.

The GFCI receptacles can be tested with the TEST and

RESET buttons.

To test:

Depress the TEST button. This should cause the Reset

button to pop out.

 To restore power, depress the RESET button.

Perform this test monthly to ensure proper operation of the

GFCI. If the generator is stored outdoors, unprotected from

the weather, test the GFCI receptacle before each use.

Page 9 — English

Example:

Tool or Appliance

Running

Watts*

Starting

Watts*

RV Air Conditioner

(11,000 BTU)

1010 1600

TV (Tube Type) 300 0

RV Refrigerator 180 600

Radio 200 0

Light (75 Watts) 300 0

Coffee Maker 600 0

2590 Total

Running Watts

1600 Highest

Starting Watts

Total Running Watts 2590

Highest Starting Watts + 1600

Total Starting Watts Needed 4190

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

ELECTRICAL

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

Tool or Appliance

Estimated

Running

Watts*

Estimated

Starting

Watts*

Home / Emergency

Incandescent Lights

(4 Quantity x 75 Watts)

300 0

TV (Tube Type) 300 0

Sump Pump (1/3 hp) 800 1300

Refrigerator or Freezer 700 2200

Well Pump (1/3 hp) 1000 2000

Furnace (1/2 hp) 800 2350

Radio 200 0

Tools

Drill (3/8", 4 amps) 440 600

Circular Saw

(Heavy Duty, 7-1/4")

1400 2300

Recip Saw 960 960

Miter Saw (10") 1800 1800

Table Saw (10") 2000 2000

*Wattages listed are approximate. Check tool or equipment for actual wattage.

Page 10 — English

KNOW YOUR GENERATOR

See Figure 2.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKERS

The circuit breakers are provided to protect the generator

against electrical overload. The circuit breaker may be reset

by pressing the circuit breaker reset button.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

BATTERY CHARGING FUSE

The battery charge circuit fuse protects the battery.

DIGITAL DISPLAY

The digital display shows AC voltage output, frequency, how

long the engine has been running during the current usage

period, and the total number of hours the unit has been used.

ENGINE SWITCH/FUEL VALVE/

CHOKE LEVER

The engine switch/fuel valve/choke lever is used when start-

ing, stopping, and running the engine.

FUEL TANK

The fuel tank has a capacity of 6 gallons.

GROUND TERMINAL

The ground terminal is used to assist in properly grounding

the generator to help protect against electrical shock. Consult

with a qualified local electrician for grounding requirements

in your area.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

lubricant in the crankcase is insufficient.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove

the oil drain plug to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz outlets:

two 120 Volt AC, 20 Amp duplex GFCI receptacles and

one 240 Volt AC 30 Amp receptacle. These can be used for

operating appropriate appliances, electrical lighting, tools,

and motor loads.

RECOIL STARTER GRIP

The recoil starter grip is used to start the generator’s engine.

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type ..................................................... 420 cc OHV

Spark Plug .......................................LG F7TC or equivalent

Lubricant Fill Volume ......................... approximately 32 oz.

Fuel Volume ................................................................6 gal.

GENERATOR

Rated Voltage ................................................ 120 V / 240 V

Rated Amps .................................................66.6 A / 33.3 A

Rated Output*........................................................ 8,000 W

Starting Watts ...................................................... 10,000 W

Rated Frequency ....................................................... 60 Hz

*Rated output determined by PGMA Standard G300

Page 11 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the loose parts list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts in the Loose Parts List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the unit carefully to make sure no damage

occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the

product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 3.

The following items are included with the generator:

Key

No. Description Qty.

1 Axle ......................................................................2

2 Wheel ...................................................................2

3 Washer .................................................................2

4 Hitch Pin ..............................................................2

5 Bolt ......................................................................2

6 Rubber Foot ........................................................2

7 Lock Nut .............................................................2

8 Bottle of Engine Lubricant ...................................1

Operator’s Manual (not shown) ...........................1

TOOLS NEEDED

See Figure 4.

The following tools (not included or drawn to scale) are

needed for assembly:

Socket Wrenches

Adjustable Wrench

Phillips Screwdriver

NOTE: Do not put fuel or lubricant in the generator before

installing the feet and wheels.

INSTALLING FEET

See Figure 5.

Locate the following items:

2 rubber feet

2 lock nuts

2 bolts

Insert bolt through rubber foot, then through the cross

brace as shown.

Thread lock nut onto bolt and tighten one full turn past

snug.

NOTE: Be careful not to overtighten so that foot mate-

rial collapses.

Repeat with remaining foot.

ASSEMBLY

Page 12 — English

INSTALLING THE WHEELS

See Figure 6.

Wheels are provided to assist in moving the generator to

the desired location and should be installed on the same

side as the handle.

Locate the following items:

2 axles

2 hitch pins

2 washers

2 wheels

Raise the end of the generator where the handle is located

high enough to gain access to the frame bottom; securely

position props underneath to support.

Slide the axle through the hole in the center of the wheel.

Slide a washer onto the axle, then slide the axle into the

wheel mounting hole as shown.

Insert hitch pin to secure.

NOTE: The hitch pin should be pushed into the axle until

the center of the rests on top of the axle.

Repeat with the second wheel.

CONNECTING/DISCONNECTING BATTERY

See Figure 7.

WARNING:

To reduce the risk of electrocution or explosion, do not

short circuit the battery terminals or charge in a sealed

container. Keep sparks and flame away.

WARNING:

Keep metal objects away from the battery terminals.

Metal objects can make a connection from one terminal

to another. Shorting the battery terminals together can

cause sparks, burns, or a fire.

The battery cables must be connected before the electric

start feature of the generator can be operated.

Connect the red wire to the positive (+) terminal first, then

connect the black wire to the negative (-) terminal. Make

sure all connections are tight.

NOTE: Be careful not to short across the terminals when

installing. Shorting the terminals together can cause

sparks, damage to the battery or generator, or even burns

or explosions.

Cover the terminals with the rubber covers.

When removing the battery for replacement: disconnect

the negative (black) post, then the positive (red) post, being

careful not to short across the terminals. Always abide by the

safety warnings provided with the battery. Remove the battery

and dispose of according to local and state regulations.

ASSEMBLY

Page 13 — English

OPERATION

NOTICE:

This product is equipped with a spark arrestor that has

been evaluated by the USDA Forest Service; however,

product users must comply with Federal, State, and local

fire prevention regulations. Check with appropriate au-

thorities. Contact customer service or a qualified service

center to purchase a replacement spark arrestor.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Please contact customer service or a quali-

fied service center for assistance.

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

Only use OUTSIDE and at least 20 feet away from win-

dows, doors, and vents as recommended by the U.S

Department of Health and Human Services Centers for

Disease Control and Prevention. Your specific home and/

or wind conditions may require additional distance.

NEVER use inside a home or garage, EVEN IF doors and

windows are open.

Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

In some areas, generators are required to be registered

with local utility companies.

If the generator is used at a construction site, there may

be additional regulations which must be observed.

RAISING AND LOWERING THE HANDLE

See Figure 8.

To raise the handle (for moving the generator): pull the

handle release knob out, raise the handle, then release

the knob so it snaps into the locking position. Insert the

handle lock pin to secure the handle in place.

To lower the handle (for storing or transporting the genera-

tor): remove the handle lock pin, pull the handle release

knob out, then lower the handle to the down position.

Never use the handle to lift the generator. The handle should

only be used for moving the unit by rolling it on its wheels.

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

WARNING:

If this generator will be used only with cord and plug-

connected equipment, National Electric Code does

not require that the unit be grounded. However, other

methods of using the generator may require grounding

to reduce the risk of shock or electrocution. Consult a

qualified electrician, electrical inspector, or local agency

having jurisdiction for local codes or ordinances to find

out if grounding is needed in your situation before using

the generator.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

Page 14 — English

CHECKING/ADDING LUBRICANT

See Figure 9.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

NOTE: If a separate engine manual is provided for this

product, please follow the instructions provided in the

engine manual instead of the information listed below.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

This engine comes with a feature that will shut off the engine

when a specific lubricant level is not maintained. The engine

will not restart until an appropriate lubricant level is reached.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

Unscrew the oil cap/dipstick and remove.

Wipe dipstick clean and re-seat in hole; do not re-thread.

Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

If level is low, add engine lubricant until the fluid level rises

to the upper portion of the dipstick.

Replace and secure the oil cap/dipstick.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being add-

ed to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

Replace and secure the fuel tank cap.

Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

ETHANOL-BLENDED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It is a viola-

tion of federal law and will damage the unit and void

your warranty. Only use unleaded gasoline containing

up to 10% ethanol.

ADDING FUEL

See Figure 10.

DANGER:

Risk of fire and serious burns: Never remove fuel cap

when unit is running. Shut off engine and allow the unit

to cool at least five minutes. Remove cap slowly.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

When adding gas to the generator, make sure the unit is sitting

on a flat, level surface. If the engine is hot, let the generator

cool for five minutes before adding gas. ALWAYS fill the fuel

tank outdoors with the machine turned off.

Move the engine switch/fuel valve/choke lever to the OFF

position.

Remove the fuel cap slowly.

Fill the fuel tank to 1 in. below the top of the fuel neck.

Replace and secure the fuel cap.

WARNING:

Always shut off engine before fueling. Never remove

fuel cap or add fuel to a machine with a running or hot

engine. Make sure the unit is sitting on a flat, level sur-

face and only add fuel outdoors. If the engine is hot, let

the unit cool for at least five minutes before adding fuel.

After fueling, immediately replace fuel cap and tighten

securely. Move at least 30 ft. from refueling site before

starting engine. Do not smoke and stay away from open

flames and sparks! Failure to follow these instructions

could result in a fire and cause serious personal injury.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

DIGITAL DISPLAY

See Figure 11.

Press and release the mode button to cycle through the

following displays:

Voltage (V) displays the operating voltage of the generator.

Frequency (F) displays the frequency in hertz at which the

generator is running.

The Run/Maintenance Timer displays the amount of time

the generator has run since being started. This timer resets

each time the generator is shut off.

OPERATION

Page 15 — English

When a cumulative run time of 25 hours has been reached,

P25 will display on the meter as a reminder to change the

engine lubricant after the initial 25 hours of run time.

When a cumulative time of 50 hours is reached, P50 will

display on the meter to remind you to clean the air filter.

When a cumulative time of 100 hours is reached, P100 will

display on the meter to remind you to change/clean the fuel

filter, clean the air filter, and change the engine lubricant.

ELECTRIC START

This generator model is provided with both electric start and

recoil start capabilities. Avoid prolonged cranking, as it can

damage the engine.

The battery provided is a nominal 12 volt sealed rechargeable

lead-acid battery and can be operated in any position without

leakage. It complies with non-spillable battery regulations.

Its convenient size offers a 30% reduction over conventional

batteries.

NOTE: Brand new generators are shipped with the battery

connections disconnected. The positive and negative

terminals must be connected to the battery before the Electric

Start feature will work.

For initial battery connection, see Connecting/Disconnecting

Battery.

STARTING THE ENGINE

See Figures 12 - 14.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

Unplug all loads from the generator.

Verify the run switch is in the ON position.

Move the engine switch/fuel valve/choke lever to the

START position.

NOTE: If engine is warm or the temperature is above

50˚F,movetheengineswitch/fuelvalve/chokeleverto

the RUN position.

Press the start button to start the engine.

NOTE: The battery may require charging before the gen-

erator can be started using only the engine switch. The

generator can be started by pulling the recoil starter grip.

Once the generator is started, the battery will charge as

the unit runs.

The generator can also be started by pulling the recoil

starting grip until the engine runs.

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

Allow the engine to run for 15–30 seconds, then move the

engine switch/fuel valve/choke lever to the RUN position.

STOPPING THE ENGINE

See Figures 12 - 13.

To stop the engine under normal operating conditions:

Remove any load from the generator.

Move the engine switch/fuel valve/choke lever to the OFF

position.

To stop the unit quickly in an emergency:

Place the run switch in the OFF position.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases could be hot enough to cause serious burns and/

or ignite combustible objects.

MOVING THE GENERATOR

See Figure 15.

Turn off the generator.

Raise the handle to the up position.

Disconnect any equipment that is plugged into the gen-

erator.

Verify the engine switch/fuel valve/choke lever is in the

OFF position.

Allow 30 minutes of “cool down” time before storing the

machine. Make sure engine and exhaust of unit are cool.

With your foot on the rear of the frame, tilt the machine

toward you until it balances on the wheels, then roll the

machine to the desired location.

LIFTING THE GENERATOR

See Figure 16.

Turn off the generator.

Fold the handle to the down position. Never lift or carry

this product using the handle.

NOTE: This tool is heavy and requires several people to

lift. To avoid back injury, keep your knees bent and lift

with your legs, not your back, and get help when needed.

HIGH ALTITUDE OPERATION

Your engine is configured for operation below 2,000 feet

altitude at the factory. Your engine must be reconfigured for

operation above 2,000 feet altitude. Operating the engine

with the wrong engine configuration at a given altitude may

increase its emissions, decrease fuel efficiency, degrade per-

formance, and cause irreversible damage. Engines configured

for high altitude operation cannot be operated in standard

altitude conditions. A qualified service center should ensure

that your engine is properly configured for your location.

OPERATION

Page 16 — English

Normal maintenance, replacement or repair of emission con-

trol devices and systems may be performed by any qualified

repair establishment or individual with original or equivalent

parts. Warranty and recall repairs must be performed by an

authorized service center; please contact customer service

for assistance.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Allow 30 minutes of cool down time before perform-

ing any maintenance. Failure to follow these instructions

can result in serious personal injury or property damage.

WARNING:

When servicing, use only recommended or equivalent

replacement parts. Use of any other parts could create

a hazard or cause product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced. Please contact customer service or a qualified

service center for assistance.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it

is not exposed to dust, dirt, moisture, or corrosive vapors.

Do not allow the cooling air slots in the generator to become

clogged with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water en-

tering the fuel system or other internal parts of the unit can

cause problems that will decrease the life of the generator.

To clean the unit:

Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

Clean air vents with low pressure air that does not exceed

25 psi.

Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 17.

For proper performance and long life, keep air filter clean.

Rotate knob counterclockwise to release. Remove cover

and set aside.

Remove the filter element.

If the filter element is dirty, clean with warm, soapy water.

Rinse and let dry.

Apply a light coat of engine lubricant to the element, then

squeeze it out.

Replace the element in the air filter unit.

Replace the air filter cover and rotate knob clockwise to

secure.

NOTE: Do not run the generator without the air filter. Rapid

engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 18.

Remove the oil cap/dipstick.

Place a container underneath the oil drain plug to collect

used lubricant as it drains.

Unscrew the oil drain plug and remove.

Allow lubricant to drain completely.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

Reinstall the oil drain plug and tighten securely.

Refill with lubricant following the instructions in the

Checking/Adding Lubricant section. For amount of

lubricant needed to refill, see Product Specifications

earlier in this manual or the accompanying engine manual,

if applicable.

Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

MAINTENANCE

La page charge ...

Ryobi RY908000E Le manuel du propriétaire

Marque: Ryobi

Modèle: RY908000E

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Ryobi RY908000E Owner's manual
español: Ryobi RY908000E El manual del propietario

Ryobi RY908000E Le manuel du propriétaire

Ryobi RY908000E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents