STIHL HS 81 Manuel utilisateur

Marque: STIHL

Modèle: HS 81

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

{

STIHL HS 81

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 27

F Notice d’emploi

28 - 58

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-442-8221-C. VA2.B14.

0000002480_006_GB

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

{

with electronic systems.

Contents

Dear Customer,

Thank you for choosing a quality

engineered STIHL product.

It has been built using modern

production techniques and

comprehensive quality assurance.

Every effort has been made to ensure

your satisfaction and troublefree use of

the product.

Please contact your dealer or our sales

company if you have any queries

concerning this product.

Your

Dr. Nikolas Stihl

Guide to Using this Manual 2

Safety Precautions and Working

Techniques 2

Using the Unit 8

Fuel 9

Fueling 10

Rear Handle 11

Starting / Stopping the Engine 12

Cleaning the Air Filter 13

Engine Management 14

Adjusting the Carburetor 14

Spark Arresting Screen in Muffler 16

Checking the Spark Plug 17

Lubricating the Gearbox 18

Rewind Starter 18

Storing the Machine 19

Sharpening Instructions 19

Inspections and Maintenance by

Dealer 19

Maintenance and Care 20

Main Parts 22

Specifications 24

Special Accessories 24

Maintenance and Repairs 25

Disposal 25

STIHL Limited Emission Control

Warranty Statement 25

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Pictograms

The meanings of the pictograms

attached to the machine are explained in

this manual.

Depending on the model concerned, the

following pictograms may be attached to

your machine.

Symbols in text

WARNING

Warning where there is a risk of an

accident or personal injury or serious

damage to property.

NOTICE

Caution where there is a risk of

damaging the machine or its individual

components.

Engineering improvements

STIHL's philosophy is to continually

improve all of its products. For this

reason we may modify the design,

engineering and appearance of our

products periodically.

Therefore, some changes, modifications

and improvements may not be covered

in this manual.

Observe all applicable local safety

regulations, standards and ordinances.

If you have not used this type of power

tool before: Have your dealer or other

experienced user show you how to

operate your unit or attend a special

course in its operation.

Minors should never be allowed to use a

power tool.

Keep bystanders, especially children,

and animals away from the work area.

When the power tool is not in use, shut it

off so that it does not endanger others.

Secure it against unauthorized use.

The user is responsible for avoiding

injury to third parties or damage to their

property.

Guide to Using this Manual

Fuel tank; fuel mixture of

gasoline and engine oil

Operate manual fuel

pump

Filler hole for gear

lubricant

Blade lock

Rotating handle

Safety Precautions and

Working Techniques

Special safety precau

tions must be observed

when working with this

power tool because it has

very sharp, high-speed

cutting blades.

It is important that you

read the instruction man

ual before first use and

keep it in a safe place for

future reference. Non-

observance of the

instruction manual may

result in serious or even

fatal injury.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

The use of noise emitting power tools

may be restricted to certain times by

national or local regulations.

To operate the power tool you must be

rested, in good physical condition and

mental health.

If you have any condition that might be

aggravated by strenuous work, check

with your doctor before operating a

power tool.

Persons with pacemakers only: The

ignition system of your power tool

produces an electromagnetic field of a

very low intensity. This field may

interfere with some pacemakers. STIHL

recommends that persons with

pacemakers consult their physician and

the pacemaker manufacturer to reduce

any health risk.

Do not operate the power tool if you are

under the influence of any substance

(drugs, alcohol) which might impair

vision, dexterity or judgment.

Use your hedge trimmer only for cutting

hedges, shrubs, scrub and similar

materials. Do not use your power tool for

any other purpose because of the

increased risk of accidents.

It must not be used for any other

purpose because of the increased risk of

accidents and damage to the machine.

Never attempt to modify your power tool

in any way since this may result in

accidents or damage to the machine.

Only use parts and accessories that are

explicity approved for this power tool by

STIHL or are technically identical. If you

have any questions in this respect,

consult a servicing dealer. Use only high

quality parts and accessories in order to

avoid the risk of accidents and damage

to the machine.

STIHL recommends the use of original

STIHL replacement parts. They are

specifically designed to match the

product and meet your performance

requirements.

Never attempt to modify your unit in any

way since this may increase the risk of

personal injury. STIHL excludes all

liability for personal injury and damage

to property caused while using

unauthorized attachments.

Do not use a pressure washer to clean

the unit. The solid jet of water may

damage parts of the unit.

Clothing and Equipment

Wear proper protective clothing and

equipment.

Avoid clothing that could get caught on

branches or brush or moving parts of the

machine. Do not wear a scarf, necktie or

jewelry. Tie up and confine long hair

(e.g. with a hair net, cap, hard hat, etc.).

Wear sturdy shoes with non-slip soles.

STIHL offers a comprehensive range of

personal protective clothing and

equipment.

Transporting the Power Tool

Always turn off the engine.

Always fit the blade guard (scabbard)

before carrying your hedge trimmer

short distances.

Carry the power tool by the handle –

cutting blades behind you. Avoid

touching hot parts of the machine,

especially the muffler and gear housing

– you could suffer serious burns.

In vehicles: Properly secure your power

tool to prevent turnover, fuel spillage and

damage.

Fueling

Always shut off the engine before

refueling.

Clothing must be sturdy

but allow complete free

dom of movement. Wear

snug-fitting clothing, an

overall and jacket combi

nation, do not wear a

work coat.

Wear safety glasses and

hearing protection, e.g.

earplugs or ear muffs.

Wear heavy-duty work

gloves made of durable

material (e.g. leather).

Gasoline is an extremely

flammable fuel. Keep

clear of naked flames. Do

not spill any fuel – do not

smoke.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Do not fuel a hot engine – fuel may spill

and cause a fire.

Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly and avoid fuel spillage.

Fuel your power tool only in well-

ventilated areas. If you spill fuel, wipe

the machine immediately – if fuel gets on

your clothing, change immediately.

Your power tool comes standard with

either a screw-type or bayonet-type fuel

cap.

This reduces the risk of unit vibrations

causing the fuel cap to loosen or come

off and spill quantities of fuel.

To reduce the risk of serious or fatal

burn injuries, check for fuel leakage. If

fuel leakage is found, do not start or run

the engine until leak is fixed.

Before Starting

Check that your power tool is properly

assembled and in good condition – refer

to appropriate chapters in the instruction

manual.

– Check the fuel system for leaks,

paying special attention to visible

parts such as the tank cap, hose

connections and the manual fuel

pump (on machines so equipped). If

there are any leaks or damage, do

not start the engine – risk of fire.

Have your machine repaired by a

servicing dealer before using it

again.

– Engage the blade lock (if fitted).

– Slide control / stop switch must

move easily to STOP or 0.

– Smooth action of throttle trigger

lockout and throttle trigger – the

throttle trigger must return

automatically to the idle position.

– Check that the spark plug boot is

secure – a loose boot may cause

arcing that could ignite combustible

fumes and cause a fire.

– Cutting blades securely mounted

and in good condition (clean, move

freely, not warped), properly

sharpened and thoroughly sprayed

with STIHL resin solvent (lubricant).

– Check cutter guard (if fitted) for

damage.

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the power tool.

To reduce the risk of accidents, do not

operate your power tool if it is damaged

or not properly assembled.

Starting the Engine

Start the engine at least 3 meters from

the fueling spot, outdoors only.

Place the power tool on firm ground in

an open area. Make sure you have good

balance and secure footing. Hold the

power tool securely. The cutting blades

must be clear of the ground and all other

obstructions because they may begin to

run when the engine starts.

Your power tool is designed to be

operated by one person only. Do not

allow other persons in the work area –

even when starting.

To reduce the risk of injury, avoid

contact with the cutting blades.

Do not drop start the power tool – start

the engine as described in the

instruction manual.

Note that the cutting blades continue to

run for a short period after you let go of

the throttle trigger – flywheel effect.

Check idle speed setting: The cutting

blades must not move when the engine

is idling with the throttle trigger released.

Holding and Controlling the Unit

Always hold the power tool firmly with

both hands on the handles. Wrap your

fingers and thumbs around the handles.

After fueling, tighten

down the screw-type fuel

cap as securely as

possible.

Insert the fuel cap with

hinged grip (bayonet-type

cap) correctly in the

opening, turn it clockwise

as far as stop and fold the

grip down.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Right-handers

Right hand on the control handle and left

hand on the front handle.

Left-handers

Left hand on the control handle and right

hand on the front handle.

Make sure you have firm and secure

footing and hold the power tool so that

the cutting blades are always away from

your body.

During Operation

In the event of impending danger or in

an emergency, switch off the engine

immediately by moving the slide control

/ stop switch to 0 or STOP.

Check that there are no bystanders in

the general work area.

Watch the cutting blades at all times – do

not cut areas of the hedge that you

cannot see.

Be extremely careful when cutting tall

hedges, check the other side of the

hedge before starting work.

Make sure the idle speed setting is

correct. The cutting blades must not run

when the engine is idling with the throttle

trigger released.

If the cutting blades still run, have your

dealer check your machine and make

proper adjustments or repairs. Check

and correct the idle speed setting

regularly.

Note that the cutting blades continue to

run for a short period after you let go of

the throttle trigger – flywheel effect.

The gearbox becomes hot during

operation. To reduce the risk of burn

injury, do not touch the gearbox housing.

Take special care in slippery conditions

(ice, wet ground, snow), on slopes or

uneven ground.

Clear away fallen branches, scrub and

cuttings.

Watch out for obstacles: Roots, tree

stumps or holes which could cause you

to trip or stumble.

Make sure you always have good

balance and secure footing.

When working at heights:

– Always use a lift bucket

– Never work on a ladder or in a tree

– Never work on an insecure support

– Never operate your power tool with

one hand

Be particularly alert and cautious when

wearing hearing protection because

your ability to hear warnings (shouts,

alarms, etc.) is restricted.

To reduce the risk of accidents, take a

break in good time to avoid tiredness or

exhaustion.

Work calmly and carefully – in daylight

conditions and only when visibility is

good. Stay alert so as not to endanger

others.

To reduce the risk of serious or fatal

injury from breathing toxic fumes,

ensure proper ventilation when working

in trenches, hollows or other confined

locations.

To reduce the risk of accidents, stop

work immediately in the event of

nausea, headache, visual disturbances

(e.g. reduced field of vision), problems

with hearing, dizziness, deterioration in

ability to concentrate. Apart from other

possibilities, these symptoms may be

caused by an excessively high

concentration of exhaust gases in the

work area.

Your power tool produces

toxic exhaust fumes as

soon as the engine is

running. These fumes

may be colorless and

odorless and contain

unburned hydrocarbons

and benzol. Never run

the engine indoors or in

poorly ventilated loca

tions, even if your model

is equipped with a cata

lytic converter.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Operate your power tool so that it

produces a minimum of noise and

emissions – do not run the engine

unnecessarily, accelerate the engine

only when working.

To reduce the risk of fire, do not smoke

while operating or standing near your

power tool. Note that combustible fuel

vapor may escape from the fuel system.

If your power tool is subjected to

unusually high loads for which it was not

designed (e.g. heavy impact or a fall),

always check that it is in good condition

before continuing work – see also

"Before Starting". Check the fuel system

in particular for leaks and make sure the

safety devices are working properly. Do

not continue operating your power tool if

it is damaged. In case of doubt, have the

unit checked by your servicing dealer.

Do not operate your power tool in the

starting throttle position – engine speed

cannot be controlled in this position.

Inspect the hedge and work area to

avoid damaging the cutting blades:

– Remove stones, rocks, pieces of

metal and other solid objects.

– When working close to the ground,

make sure that no sand, grit or

stones get between the blades.

– Take particular care when cutting

hedges next to or against wire

fences.

To avoid the risk of electrocution, do not

touch electric power lines – never cut

through electric power lines.

Opening the throttle while the blades are

blocked increases the load and reduces

engine speed. The clutch then slips

continuously and this causes

overheating and damage to important

components (e.g. clutch, polymer

housing components) – and this can

increase the risk of injury from the

cutting blades moving while the engine

is idling.

If the hedge is very dusty or dirty, spray

the blades with STIHL resin solvent from

time to time during cutting. This helps

reduce blade friction as well as the

aggressive effects of sap and the build-

up of dirt particles.

The dust that occurs during operation

may be harmful to health. If dust levels

are very high, wear a suitable respirator.

Before leaving the power tool

unattended: Shut off the engine.

Check the cutting blades at regular short

intervals during operation or

immediately if there is a noticeable

change in cutting behavior:

– Shut off the engine.

– Wait until the cutting blades have

come to a complete standstill.

– Check condition and tightness, look

for cracks.

– Check sharpness.

To reduce the risk of fire, always clean

plant residue, chips, leaves and excess

lubricant off the engine and muffler.

After Finishing Work

Always clean dust and dirt off the

machine – do not use any grease

solvents for this purpose.

Spray the blades with STIHL resin

solvent. Run the motor briefly so that the

solvent is evenly distributed.

Vibrations

Prolonged use of the power tool may

result in vibration-induced circulation

problems in the hands (whitefinger

disease).

No general recommendation can be

given for the length of usage because it

depends on several factors.

The period of usage is prolonged by:

– Hand protection (wearing warm

gloves)

– Work breaks

Do not touch the cutting

blades while the motor is

running. If the cutting

blades become jammed

by thick branches or

other obstructions, switch

off the engine immedi

ately before attempting to

free the blades – there is

otherwise a risk of injury.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

The period of usage is shortened by:

– Any personal tendency to suffer

from poor circulation (symptoms:

frequently cold fingers, tingling

sensations).

– Low outside temperatures.

– The force with which the handles

are held (a tight grip restricts

circulation).

Continual and regular users should

monitor closely the condition of their

hands and fingers. If any of the above

symptoms appear (e.g. tingling

sensation in fingers), seek medical

advice.

Maintenance and Repairs

Service the machine regularly. Do not

attempt any maintenance or repair work

not described in the instruction manual.

Have all other work performed by a

servicing dealer.

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer. STIHL dealers are

regularly given the opportunity to attend

training courses and are supplied with

the necessary technical information.

Only use high-quality replacement parts

in order to avoid the risk of accidents

and damage to the machine. If you have

any questions in this respect, consult a

servicing dealer.

STIHL recommends the use of genuine

STIHL replacement parts. They are

specifically designed to match your

model and meet your performance

requirements.

To reduce the risk of injury, always shut

off the engine before carrying out any

maintenance or repairs or cleaning the

machine. – Exception: Carburetor and

idle speed adjustments.

Do not turn the engine over on the

starter with the spark plug boot or spark

plug removed unless the slide control /

stop switch is on STOP or 0 since there

is otherwise a risk of fire from

uncontained sparking.

To reduce the risk of fire, do not service

or store your machine near open flames.

Check the fuel filler cap for leaks at

regular intervals.

Use only a spark plug of the type

approved by STIHL and make sure it is

in good condition – see "Specifications".

Inspect the ignition lead (insulation in

good condition, secure connection).

Check the condition of the muffler.

To reduce the risk of fire and damage to

hearing, do not operate your machine if

the muffler is damaged or missing.

Do not touch a hot muffler since burn

injury will result.

Vibration behavior is influenced by the

condition of the AV elements – check the

AV elements at regular intervals.

Maintenance, replacement, or repair of

the emission control devices and

systems may be performed by any

nonroad engine repair establishment or

individual. However, if you make a

warranty claim for a component which

has not been serviced or maintained

properly or if nonapproved replacement

parts were used, STIHL may deny

coverage.

For any maintenance please refer to the

maintenance chart and to the warranty

statement near the end of the instruction

manual.

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

HS 81 R

The HS 81 R is designed for cutting

hedges and shrubs with thicker stems

and branches.

HS 81 T

The HS 81 T is designed for shaping

and trimming hedges and shrubs with

thinner branches.

Use the HS 81 R hedge trimmer for

cutting hedges with thicker branches.

Cutting Season

Observe country-specific or municipal

rules and regulations for cutting hedges.

Do not use your power tool during other

people's rest periods.

Cutting Sequence

Use lopping shears or a chain saw to cut

out thick branches first.

Cut both sides of the hedge first, then

the top.

Disposal

Do not throw cuttings in the garbage can

– they can be composted!

Working Technique

Vertical Cut

Swing the cutting blade from the bottom

upwards in an arc – lower the nose of the

blade, move along the hedge and then

swing the blade up again in an arc.

Any working position above head height

is tiring. To minimize the risk of

accidents, work in such positions for

short periods only.

Using the Unit

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Horizontal Cut

Hold the cutter bar at an angle of 0° to

10° as you swing the hedge trimmer

horizontally.

Swing the cutting blade in an arc

towards the outside of the hedge so that

the cuttings are swept to the ground.

This engine is certified to operate on

unleaded gasoline and with the mix ratio

50:1.

Your engine requires a mixture of high-

quality premium gasoline and high-

quality two-stroke air-cooled engine oil.

Use premium branded unleaded

gasoline with a minimum octane rating

of 89 (R+M)/2.

Note: Models equipped with a catalytic

converter require unleaded gasoline. A

few tankfuls of leaded gasoline can

reduce the efficiency of the catalytic

converter by more than 50%.

Fuel with a lower octane rating may

result in preignition (causing "pinging")

which is accompanied by an increase in

engine temperature. This, in turn,

increases the risk of the piston seizure

and damage to the engine.

The chemical composition of the fuel is

also important. Some fuel additives not

only detrimentally affect elastomers

(carburetor diaphragms, oil seals, fuel

lines etc.), but magnesium castings as

well. This could cause running problems

or even damage the engine. For this

reason it is essential that you use only

high-quality fuels!

Fuels with different percentages of

ethanol are being offered. Ethanol can

affect the running behaviour of the

engine and increase the risk of lean

seizure.

Gasoline with an ethanol content of

more than 10% can cause running

problems and major damage in engines

with a manually adjustable carburetor

and should not be used in such engines.

Engines equipped with M-Tronic can be

run on gasoline with an ethanol content

of up to 25% (E25).

Use only STIHL two-stroke engine oil or

equivalent high-quality two-stroke air-

cooled engine oils for mixing.

We recommend STIHL 50:1 two-stroke

engine oil since it is specially formulated

for use in STIHL engines.

Do not use BIA or TCW (two-stroke

water cooled) mix oils!

Use only STIHL 50:1 heavy-duty engine

oil or an equivalent quality two-stroke

engine oil for the fuel mix in models

equipped with a catalytic converter.

Take care when handling gasoline.

Avoid direct contact with the skin and

avoid inhaling fuel vapour.

The canister should be kept tightly

closed in order to avoid any moisture

getting into the mixture.

The fuel tank and the canister in which

fuel mix is stored should be cleaned

from time to time.

Fuel mix ratio

Only mix sufficient fuel for a few days

work, not to exceed 30 days of storage.

Store in approved safety fuel-canisters

only. When mixing, pour oil into the

canister first, and then add gasoline.

Fuel

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Dispose of empty mixing-oil canisters

only at authorized disposal locations.

Preparations

N Before fueling, clean the filler cap

and the area around it to ensure that

no dirt falls into the tank.

N Position the machine so that the

filler cap is facing up.

Opening the Cap

N Swing the grip to the upright

position.

N Rotate the cap about 1/4 turn

counterclockwise.

N Remove the cap.

Filling up with fuel

Take care not to spill fuel while fueling

and do not overfill the tank.

STIHL recommends you use the STIHL

filler nozzle for fuel (special accessory).

Closing the Cap

N Insert the cap in the opening – with

the grip upright – the marks must

line up.

N Rotate the cap clockwise as far as

stop (about 1/4 turn).

Examples

Gasoline Oil (STIHL 50:1 or equiva

lent high-quality oils)

liters liters (ml)

10.02(20)

5 0.10 (100)

10 0.20 (200)

15 0.30 (300)

20 0.40 (400)

25 0.50 (500)

Fueling

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

N Fold the grip down so that it is flush

with the top of the cap.

If the grip does not lie completely flat on

the cap and the grip's lug does not

engage the recess (see arrow), the cap

is not properly closed and you must

repeat the above steps.

Change the fuel pickup body every year

N Drain the fuel tank.

N Use a hook to pull the fuel pickup

body out of the fuel tank and take it

off the hose.

N Push the new fuel pickup body into

the hose.

N Place the fuel pickup body in the

fuel tank.

The rear handle can be turned through

90° to the left or right for better control

and comfort in all cutting situations.

N Let go of the throttle trigger. Do not

open the throttle.

N Release the lock (1).

N Turn the handle (2) to the required

position and re-engage the lock (1).

The throttle trigger may be used again

when the handle is locked in position.

Do not operate the throttle while the

handle lock is released. Never release

the lock while you are operating the

throttle.

Rear Handle

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

N Observe safety precautions – see

chapter on "Safety Precautions and

Working Techniques".

N Move the stop switch (1) to I.

N Press down the throttle interlock (2)

and squeeze the throttle trigger (3)

at the same time – hold both levers

in that position.

N Press in the starting throttle

button (4).

N Let go of the interlock lever, throttle

trigger and starting throttle button.

This is the starting throttle position.

N Set the choke lever (5).

N Press the fuel pump bulb at least

five times – even if the bulb is filled

with fuel.

Starting

N Place the unit on the ground.

N Remove the blade scabbard. Check

that the cutting blades are not

touching the ground of any other

obstacles.

N Make sure you have a firm footing.

N Hold the unit firmly with your left

hand on the fan housing and press

down.

N Hold the starter grip with your right

hand.

Models without ErgoStart

N Pull the starter grip slowly until you

feel it engage and then give it a brisk

strong pull.

NOTICE

Do not pull out the starter rope all the

way – it might otherwise break.

N Do not let the starter grip snap back.

Guide it slowly back into the housing

so that the starter rope can rewind

properly.

Models with ErgoStart

N Pull the starter grip steadily.

When the engine begins to fire:

N Move the choke lever to e and

continue cranking.

As soon as the engine runs

N Open the throttle wide – the starting

throttle button pops out and the

engine can settle down to idle

speed.

Stopping the engine

N Move the stop switch to 0.

Starting / Stopping the

Engine

g If the engine is cold

e for warm start – also use this posi

tion if the engine has been running

but is still cold.

443BA038 KN

443BA039 KN

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Other hints on starting

At very low outside temperatures –

warm up the engine

As soon as the engine runs:

N Allow engine to run in starting

throttle position for about 10

seconds.

N Open the throttle wide – the starting

throttle button pops out and the

engine can settle down to idle

speed.

If the engine does not start

If you did not turn the choke lever to e

quickly enough after the engine began to

fire, the combustion chamber is flooded.

N Set the choke lever to e – even if

the engine is cold.

N Now start the engine with a few

brisk pulls of the starter rope.

If fuel tank has been run completely dry

and then refueled

N Press the fuel pump bulb at least

five times – even if the bulb is filled

with fuel.

N Now start the engine.

The unit is equipped with either a felt or

paper filter element.

If there is a noticeable loss of engine

power

Felt filter

N Turn the choke lever to g

N Take out the screw (1).

N Remove the filter cover (2).

N Clean away loose dirt from around

the filter.

N Remove the filter element (3).

N Fit a new filter element. As a

temporary measure you can knock it

out on the palm of your hand or blow

it out with compressed air. Do not

wash.

N Install the filter element.

N Fit the filter cover.

N Insert the screw and tighten it down

firmly.

Paper filter

N Turn the choke lever to g

N Take out the screw (1).

N Remove the filter cover (2).

N Clean away loose dirt from around

the filter and inside the filter cover.

N Remove and check the filter

element (3) – replace if dirty or

damaged.

N Fit the filter in the filter housing.

Cleaning the Air Filter

443BA040 KN

443BA034 KN

443BA035 KN

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

N Position filter cover against the left

side of the filter housing and swing it

to the right – the two lugs (arrows)

must engage the filter cover

openings.

N Insert the screw and tighten it down

firmly.

Exhaust emissions are controlled by the

design of the fundamental engine

parameters and components (e.g.

carburation, ignition, timing and valve or

port timing) without the addition of any

major hardware.

General Information

The carburetor comes from the factory

with a standard setting.

This setting provides an optimum fuel-air

mixture under most operating

conditions.

Preparations

N Shut off the engine.

N Check the air filter and clean or

replace if necessary.

N Check the spark arresting screen

(not in all models, country-specific)

in the muffler and clean or replace if

necessary.

N Inspect cutting blades and clean if

necessary (clean, move freely, not

warped).

Different Standard Settings

Different carburetors are installed at the

factory. A different standard setting is

necessary for each of these carburetors.

Standard setting A

– High speed screw (H) = 3/4

– Low speed screw (L) = 1

Standard setting B

– High speed screw (H) = 3/4

– Low speed screw (L) = 3/4

443BA036 KN

Engine Management Adjusting the Carburetor

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

N Determine the required standard

setting as follows: Turn the low

speed screw (L) carefully clockwise

as far as stop, then turn it

counterclockwise.

Is range of adjustment more than 1 turn?

N Continue with "Standard setting A"

Is range of adjustment less than 1 turn?

N Continue with "Standard setting B"

Standard setting A

N Turn high speed screw (H)

counterclockwise as far as stop (no

more than 3/4 turn).

N Turn the low speed screw (L)

carefully clockwise until it is against

its seat, then turn it back 1 full turn

Standard setting B

N Turn high speed screw (H)

counterclockwise as far as stop (no

more than 3/4 turn).

N Turn the low speed screw (L)

clockwise as far as stop, then turn it

back 3/4 turn.

Adjusting Idle Speed

N Carry out the standard setting.

N Start and warm up the engine.

Engine stops while idling

N Turn the idle speed screw (LA)

clockwise until the cutting blades

begin to run – then back it off

2 1/2 turns.

Cutting blades run when engine is idling

N Turn the idle speed screw (LA)

counterclockwise until the cutting

blades stop moving – then turn it

another 2 1/2 turns in the same

direction.

WARNING

If the cutting blades continue moving

when the engine is idling, have your

power tool checked and repaired by your

servicing dealer.

Erratic idling behavior, poor acceleration

(despite correction to setting of LA

screw).

Idle setting is too lean

N Rotate the low speed screw (L)

about 1/4 turn counterclockwise

until the engine runs and

accelerates smoothly.

Engine stops when unit is swung at idle

speed

Idle setting is too rich

N Rotate the low speed screw (L)

about 1/4 turn clockwise until the

engine idles smoothly.

It is usually necessary to change the

setting of the idle speed screw (LA) after

every correction to the low speed

screw (L).

Fine tuning for operation at high altitude

A slight correction of the setting may be

necessary if engine does not run

satisfactorily:

443BA043 KN

443BA044 KN

443BA045 KN

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

N Carry out the standard setting.

N Warm up the engine.

N Turn high speed screw (H) slightly

clockwise (leaner) – no further than

stop.

NOTICE

After returning from high altitude, reset

the carburetor to the standard setting.

If the setting is too lean there is a risk of

engine damage due to insufficient

lubrication and overheating.

In some countries the muffler is

equipped with a spark arresting screen.

N Check the spark arresting screen in

the muffler after every 20 hours of

operation, or if the engine is down

on power or runs erratically at

maximum speed.

WARNING

Wait for the engine to cool down

completely before performing this work.

N Take out the screws (1).

N Remove the exhaust pipe (2).

N Use a 15 mm socket wrench to

unscrew the spark arresting screen.

N Clean the spark arresting screen. If

the screen is damaged or heavily

carbonized, fit a new one.

N Refit the spark arresting screen.

N Fit the exhaust pipe.

N Fit the screws.

Spark Arresting Screen in

Muffler

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

If the engine is down on power, difficult

to start or runs poorly at idle speed, first

check the spark plug.

N Removing the spark plug

N Clean dirty spark plug.

N Check electrode gap (A) and

readjust if necessary – see

"Specifications".

N Rectify the problems which have

caused fouling of the spark plug.

Possible causes are:

– Too much oil in fuel mix.

– Dirty air filter.

– Unfavorable running conditions.

N Fit a new spark plug after about 100

operating hours – or sooner if the

electrodes are badly eroded. Install

only suppressed spark plugs of the

type approved by STIHL – see

"Specifications".

To reduce the risk of arcing and fire

If the spark plug comes with a

detachable adapter nut:

N Screw the adapter nut (1) onto the

thread and tighten it down firmly.

On all spark plugs

N Always press the boot (2) firmly on

to the spark plug (3).

Checking the Spark Plug

000BA002 KN

000BA045 KN

000BA050 KN

HS 81 R, HS 81 RC, HS 81 T, HS 81 TC

English

Use STIHL gear lubricant for hedge

trimmers (special accessory) for

lubricating the blade drive gear.

After about 25 hours of operation:

N Remove the screw plug (1) from the

gear housing on the underside of

the unit.

N Screw the tube of grease (2) into the

filler hole.

N Squeeze up to 5 g grease into the

gearbox.

NOTICE

Do not completely fill the gearbox with

grease.

N Remove the tube of grease (2).

N Refit the filler plug and tighten it

down firmly.

To help prolong the wear life of the

starter rope, observe the following

points:

N Pull the starter rope only in the

direction specified.

N Do not pull the rope over the edge of

the guide bushing.

N Do not pull out the rope more than

specified.

N Do not allow the starter grip to snap

back, guide it back into the housing

slowly – see chapter on "Starting /

Stopping the Engine."

Have a damaged starter rope replaced

by your dealer before it breaks

completely. STIHL recommends that

you have servicing and repair work

carried out exclusively by an authorized

STIHL servicing dealer.

Lubricating the Gearbox Rewind Starter

La page charge ...

STIHL HS 81 Manuel utilisateur

Marque: STIHL

Modèle: HS 81

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: STIHL HS 81 User manual

Documents connexes

Autres documents

Trumpf S 350-3 Manuel utilisateur