ATEN KH1508A Manuel utilisateur

ATEN Altusen™

KH1508A / KH1516A /

KH1532A

KVM Switch

User Manual

KH1508A / KH1516A / KH1532A User Manual

ii

Compliance Statements

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

Warning

Operation of this equipment in a residential environment could cause radio

interference.

Achtung

Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen

verursachen.

Suggestion

Shielded twisted pair (STP) cables must be used with the unit to ensure

compliance with FCC & CE standards.

KCC Statement

KH1508A / KH1516A / KH1532A User Manual

iii

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

RoHS

This product is RoHS compliant.

KH1508A / KH1516A / KH1532A User Manual

iv

About This Manual

This User Manual is provided to help you get the most from your KH1508A /

KH1516A / KH1532A system. It covers all aspects of installation,

configuration and operation. An overview of the information found in the

manual is provided below.

Overview

Chapter 1, Introduction, introduces you to the KH1508A / KH1516A /

KH1532A system. Its purpose, features and benefits are presented, and its front

and back panel components are described.

Chapter 2, Hardware Setup, describes how to set up your installation. The

necessary steps – from a basic single stage hookup to a complete daisy chained

operation are provided.

Chapter 3, Basic Operation, explains the fundamental concepts involved

in operating the KH1508A / KH1516A / KH1532A.

Chapter 4, OSD Operation, provides a complete description of the

KH1508A / KH1516A / KH1532A's OSD (On Screen Display), and how to

work with it.

Chapter 5, Hotkey Operation, details all of the concepts and procedures

involved in the keyboard hotkey operation of your KH1508A / KH1516A /

KH1532A installation.

Chapter 6, Keyboard Emulation, provides tables that list the PC to Mac

and PC to Sun keyboard emulation mappings.

Chapter 7, The Firmware Upgrade Utility, explains how to upgrade the

KH1508A / KH1516A / KH1532A's firmware with the latest available

versions.

An Appendix, provides specifications and other technical information

regarding the KH1508A / KH1516A / KH1532A.

KH1508A / KH1516A / KH1532A User Manual

v

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter]

means to press the Enter key. If keys need to be chorded,

they appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

>

Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start > Run means

to open the Start menu, and then select Run.

Indicates critical information.

KH1508A / KH1516A / KH1532A User Manual

vi

Package Contents

The KH1508A / KH1516A / KH1532A package consists of:

1 KH1508A, KH1516A, or KH1532A Cat 5 High-Density KVM Switch

1 firmware upgrade cable

1 power cord

1 mounting kit

1 foot pad set (4 pcs)

1 user instructions*

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the KH1508A / KH1516A / KH1532A installation.

* Features may have been added to the KH1508A / KH1516A / KH1532A

since this manual was published. Please visit our web site to download the

most up-to-date version of the manual.

KH1508A / KH1516A / KH1532A User Manual

vii

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

International http://www.aten.com

North America http://www.aten-usa.com

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

KH1508A / KH1516A / KH1532A User Manual

viii

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

KH1508A / KH1516A / KH1532A User Manual

ix

Contents

Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1.

Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Computers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

KVM Adapter Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KH1508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KH1516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

KH1532A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KH1508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KH1516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

KH1532A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Chapter 2.

Hardware Setup

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before you Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Stacking and Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Single Station Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Daisy Chaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Chapter 3.

Basic Operation

Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

OSD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Hotkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Hot Plugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

KH1508A / KH1516A / KH1532A User Manual

x

Hot Plugging Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Hot Plugging KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Hot Plugging Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Powering Off and Restarting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Port ID Numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Chapter 4.

OSD Operation

OSD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

OSD Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Main Screen Headings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

OSD Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F1: GOTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

F2: LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

F3: SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

F4: ADM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

F5: SKP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

F6: BRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

F7: SCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

F8: LOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Chapter 5.

Hotkey Operation

Hotkey Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Invoking Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Number Lock and Minus Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Control and F12 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Hotkey Mode Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Exiting Hotkey Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Selecting the Active Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Auto Scan Mode Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Setting the Scan Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Invoking Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Exiting Auto Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Skip Mode Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Entering Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Exiting Skip Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Computer Keyboard / Mouse Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting the Hotkey Beeper ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Setting the Hotkey key combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Setting the OSD Hotkey combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Setting the Port Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Restore the Default Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Hotkey Summary Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Chapter 6.

Keyboard Emulation

Mac Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Sun Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

KH1508A / KH1516A / KH1532A User Manual

xi

Chapter 7.

The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Performing the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Main Board Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . 60

Adapter Cable Firmware Upgrade Recovery. . . . . . . . . . . . . . . . .61

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Général . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Montage sur bâti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Connection Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

KH1508A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

KH1516A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

KH1532A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Compatible Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

OSD Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Administrator Login Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

KH1508A / KH1516A / KH1532A User Manual

xii

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

A KH1508A / KH1516A / KH1532A KVM switch is a control unit that allows

IT administrators to access and control multiple computers from a single PS/2

or USB KVM (keyboard, monitor, and mouse) console. A single KH1508A /

KH1516A / KH1532A KVM switch can control up to 8 / 16 / 32 computers.

By daisy chaining up to 31 additional switches, as many as 1024 computers can

be controlled from the original KVM console. An auto-sensing function

recognizes the position of each station on the chain, eliminating the need to

manually set the position, and a seven-segment front panel LED displays each

station's position for easy identification.

Compact, high-density, RJ-45 connectors and CAT 5e/6 cable make for a

compact, efficient, wiring configuration, while the use of PS/2 and USB KVM

Adapter Cables to link to the computers, permits any combination of PCs,

Macs, Sun computers, and serial devices to coexist on the installation.

Setting up the KH1508A / KH1516A / KH1532A is fast and easy – plugging

cables into their appropriate ports is all that is entailed. Because the KH1508A

/ KH1516A / KH1532A intercepts keyboard and mouse input directly, there is

no software to configure and no complex installation routines.

Access to any computer on the installation is easily accomplished – either by

pressing front panel port selection pushbuttons; entering hotkey combinations

from the keyboard; or by means of a powerful OSD (On Screen Display) menu

system. A convenient Auto Scan function also permits automatic scanning and

one-by-one monitoring of the activities of selected computers.

Your KH1508A / KH1516A / KH1532A investment is protected through

firmware upgrades. You can download firmware update files from our website,

and use the Firmware Upgrade function to quickly and conveniently install

them.

There is no better way to save time and money than with a KH1508A /

KH1516A / KH1532A installation. By allowing a single console to manage up

to 1024 computers, you: (1) eliminate the expense of purchasing separate

keyboards, monitors, and mice; (2) save space; (3) save on energy costs; and

(4) eliminate the inconvenience and wasted effort involved in constantly

having to move from one computer to another.

KH1508A / KH1516A / KH1532A User Manual

2

Features and Benefits

The features and benefits provided by a KH1508A / KH1516A / KH1532A

deployment are described in the following table:

Features Benefits

Simple Installation and

Operation

Plug-and-play installation – no software required – connecting

cables is all it takes. Station positions are automatically

recognized. Computer selection via front panel switches;

hotkeys; or multi-language OSD (On Screen Display) menus.

Single Console Control Access and control up to 8 (KH1508A) or 16 (KH1516A) or 32

(KH1532A) computers from a single PS/2 or USB KVM

(keyboard, monitor, and mouse) console.

Scalability By daisy chaining up to 31 additional KH1508A / KH1516A /

KH1532A switches*, as many as up to 1024 computers can

be controlled from the original KVM console – eliminating the

expense of purchasing separate peripherals for each server.

Note: If you wish to include KH1532A into your daisy chain,

you must have a KH1532A as the first station.

Easy Installation Setting up the KH1508A / KH1516A / KH1532A is fast and

easy – plugging cables into their appropriate ports is all that is

entailed. Because there is no software to configure,

incompatibility and configuration issues are non-existent.

Easy Operation Three port selection methods: Manual (via front panel

pushbuttons), Hotkey, and multi-language OSD (On Screen

Display).

Multi-language keyboard support includes English (US / UK),

French, German, Japanese, Korean, and Traditional Chinese.

Hardware Independent

Cross-Platform

Support

The KH1508A / KH1516A / KH1532A supports Windows

2000/XP/Vista/7, Linux, Unix, Novell, FreeBSD, Sun, and

Mac.

Space-Saving RJ-45

Connectors and Cat

5e/6 Cabling

This space-saving innovation means that the KH1508A /

KH1516A / KH1532A can be conveniently installed in a 1U

system rack, and the installation can take advantage of the

internal network wiring built into most modern commercial

buildings.

Reduces cable clutter for a neat and tidy data center

environment.

KVM Adapter Cables

to Connect to Servers

and Devices

For convenience and flexibility that allows mixing the PS/2,

USB and serial interfaces, the KH1508A / KH1516A /

KH1532A's design utilizes KVM adapter cables that serve as

intermediaries between the KVM switch and the connected

devices.

KVM adapter cables are available in PS/2, USB, and Serial

interfaces to support a wide variety of data center servers and

devices.

Chapter 1. Introduction

3

Two-Level Password

Security

Supports one administrator and ten user profiles. Strong

password protection prevents unauthorized access to the

installation – keeping your valuable data secure.

Upgradeable Firmware Stay current with the latest functionality improvements and

updates by downloading firmware upgrade files from our

website and installing them with the built-in firmware upgrade

utility.

Effortless Upgrades Simultaneous firmware upgrades to all daisy-chained KVM

switches and dongles through the daisy-chain cable.

Auto Scanning and

Broadcast Mode

Auto scanning provides hands-free monitoring of selected

devices at variable rates. Broadcast Mode sends commands

from the console to all computers – allowing you to perform

operations (such as software installation, upgrades,

shutdowns, etc.), on them simultaneously.

Superior Video Quality Supports video resolutions up to 1920 x 1200 @ 60 Hz up to

30 meters, 1600 x 1200 @ 60 Hz up to 40 meters, and 1280 x

1024 @ 75 Hz up to 50 meters.*

*With the KVM adapter cable KA7000 series.

Multiple User Accounts Supports up to 10 user and 1 administrator accounts

Hot Pluggable Ability to add or remove components without having to power

off the KVM switch.

Adapter Cables with ID The KH1508A / KH1516A / KH1532A KVM series supports

automatic ID recognition of the new ATEN KVM Cable

Adapter KA7000 series ( KVM Adapter Cables). Using the

new adapter cables with ID means it is not required to change

cable configuration settings when moving cables from port to

port.

Device ID and attributes are stored in the adapter cables

allowing you to hot-swap port connections without having to

reconfigure attributes.

Features Benefits

KH1508A / KH1516A / KH1532A User Manual

4

Requirements

Console

 A VGA, SVGA, or multisync monitor capable of the highest resolution

that you will be using on any computer in the installation

 A PS/2 or USB mouse

 A PS/2 or USB keyboard

Computers

The following equipment must be installed on the computers that connect to the

KH1508A / KH1516A / KH1532A KVM ports:

 A VGA, SVGA or multisync port

 A USB Type-A port and USB host controller (for USB KVM adapter

cable connection, see following section)

- or -

 6-pin Mini-DIN keyboard and mouse ports (for PS/2 KVM adapter cable

connection, see following section)

Chapter 1. Introduction

5

KVM Adapter Cables



Cat 5e/6 cable is required to connect the KH1508A / KH1516A / KH1532A to

one of the KVM adapter cables.



The following KVM adapter cables are required for use with the KH1508A /

KH1516A / KH1532A:

Note: 1. KVM adapter cables are referred to as I/O Modules in some dialog boxes.

2. The following cable models support the Adapter Cable ID function:

KA7166 / KA7168 / KA7169 / KA7920 / KA7970 / KA7520 / KA7570

/ KA7120 / KA7130 / KA7170.

Operating Systems

Supported operating systems are shown in the table below:

1

Does not support USB.

2

Kernels below 2.6 do not support USB 2.0

Function Module

Connect to devices with PS/2 ports KA7920 / KA7520 / KA7120

KA9520 / KA9120

Connect to devices with USB ports KA7166 / KA7168 / KA7169 /

KA7970 / KA7570 / KA7170

KA9570 / KA9170

Connect to Sun Legacy systems (with 13W3 port) KA9130 / KA7130

Connect to Sun USB systems KA9170 / KA7170

Connect to serial based devices KA9140

OS Version

Windows

NT

1

, 2000, XP, 2003 Server, 2008 Server, Vista

Linux

2

RedHat 9.0, Fedora or later, RHEL AS 4, RHEL 5

SuSE 10 or later, OpenSUSE 10.2; SLES 10 SP1

Debian 3.1, 4.0

Ubuntu 7.04, 7.10

UNIX IBM AIX4.3, 5L (V5.2,V5.3), V6 (V6.1)

FreeBSD 5.5, 6.1, 6.2

Novell Netware 5.0 or later

Sun Solaris 8, 9, 10

Mac 9.0, 9.1, 10.1, 10.2, 10.3, 10.4 , 10.5

DOS

6.2 or later

1

KH1508A / KH1516A / KH1532A User Manual

6

Components

Front View

KH1508A

KH1516A

KH1532A

43 5

1&2

67

3

1&2

67

4 5

3

1&2

67

4 5

Chapter 1. Introduction

7

No. Component Description

1 port selection

pushbuttons



Press a pushbutton to give the KVM focus to the computer

attached to its corresponding port.



Simultaneously pressing pushbuttons 1 and 2 for 3 seconds

performs a keyboard and mouse reset.



Simultaneously pressing pushbuttons 7 and 8 (KH1508A) or

15 and 16 (KH1516A) or 30 and 31(KH1516A) starts Auto

Scan mode (see F7: SCAN, page 38, for auto scan details).

2 port LEDs The port LEDs are built into the port selection pushbuttons. The

left ones are the On Line LEDs; the right ones are the Selected

Port LEDs:



An On Line LED lights green to indicate that the computer

attached to its corresponding port is up and running. A

flashing LED indicates that the Port is being used for

cascading to another switch.



A Selected LED lights orange to indicate that the computer

attached to its corresponding port is the one that has the

KVM focus. The LED is steady under normal conditions, but

flashes when its port is accessed under Auto Scan mode

(see F7: SCAN, page 38, for auto scan details).

3 reset button Pressing this button in performs a system reset.

Note: The switch is recessed and must be pushed with a small

object, such as the end of a paper clip, or a ballpoint pen.

4 firmware

upgrade

recovery

switch

During normal operation and while performing a firmware

upgrade, this switch should be in the NORMAL position. If a

firmware upgrade operation does not complete successfully,

this switch is used to perform a firmware upgrade recovery.

See Firmware Upgrade Recovery, page 60 for details.

5 firmware

upgrade port

The firmware upgrade cable that transfers the firmware

upgrade data from the administrator's computer to the

KH1508A / KH1516A / KH1532A (see page 54), plugs into this

RJ-11 connector.

6 power LED Lights to indicate that the KH1508A / KH1516A / KH1532A is

powered and ready to operate.

7 station ID

LED

The KH1508A / KH1516A / KH1532A’s station ID is displayed

here. If this is a single station installation (see page 14), or the

first station on a daisy chained installation (see page 16), the

KH1508A / KH1516A / KH1532A has a station ID of 01.

On a daisy chained installation, the KH1508A / KH1516A /

KH1532A auto-senses its position and displays the station ID

that corresponds to its place in the chain. (see Port ID

Numbering, page 24, for details).

KH1508A / KH1516A / KH1532A User Manual

8

Rear View

KH1508A

KH1516A

KH1532A

12

6

45

3

12

6

45

3

1

2

6

45

3

La page charge ...

ATEN KH1508A Manuel utilisateur

Ce manuel convient également à

ATEN KH1508A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents