GE GTL21 Manuel utilisateur

ge.com
Refrigerators
Top-Freezer
197D7733P001     49-60505-1    07-07 JR
Safety Instructions  . . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker  . . . . . . . . . . . .9
Controls . . . . . . . . . . . . . . . . . . . . . .5
Crispers and Pans  . . . . . . . . . . . .7, 8
Shelves and Bins  . . . . . . . . . . . . . . .6
Care and Cleaning
Care and Cleaning . . . . . . . . . .10, 11
Replacing the Light Bulb  . . . . . . .11
Installation Instructions
Icemaker Installation  . . . . . . . .13–16
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . .12
Reversing the Door Swing  . . . .21–25
Water Line Installation  . . . . . .17–21
Troubleshooting Tips . . . . . . .26–29
Normal Operating Sounds  . . . . . .26
Consumer Support
Consumer Support  . . . . .Back Cover
Product Registration 
for Canadian Customers  . . . . .33, 34
Product Registration 
for U.S. Customers  . . . . . . . . .31, 32
Warranty for 
Canadian Customers  . . . . . . . . . . .35
Warranty for U.S. Customers . . . . .36
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Models GTH21 and GTL21
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario 
e instalación
La section française commence à la page 37
La sección en español empieza en la página 73
Note to Installer – Be sure to leave
these instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
Note à l’installateur – Assurez-vous 
de laisser ces instructions au 
consommateur.
Note au consommateur –
Conservez ces instructions pour 
référence future.
Nota al instalador – Asegúrese 
de dejar estas instrucciones con el 
consumidor.
Nota al consumidor – Conserve 
estas instrucciones para referencia futura.
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on the gray label 
on the left side, near the top of the
refrigerator compartment.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do not

place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls (some models only

have one control) to the 1 (off) position does not

remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2

3

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

ge.com

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they will

sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow the instructions

below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

4

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

5

About the controls on the refrigerator. ge.com

Control Settings

Initially, set the control(s) at 4. Allow 24 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the control(s) one increment at a time and

allow 12 hours after each adjustment for the refrigerator to reach the temperature you

have set.

Setting the refrigerator control to 1 stops cooling in both the freezer and refrigerator

compartments but does not shut off electrical power to the refrigerator. The freezer

control (on some models) has no effect on electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions,

and may require more than one adjustment. Factors that affect temperature include the

amount of food in the refrigerator or freezer, the frequency of door opening and the

temperature of food when it is placed in the refrigerator.

4

The controls on your refrigerator will look like one of the following:

44

6

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

About the shelves and bins.

Not all features are on all models.

Rearranging the Shelves

Shelves in the refrigerator and freezer compartments are adjustable.

Refrigerator Compartment

Half-Width Shelves

One end of the shelf rests on a

molded side-wall support; a bracket

on the other end hooks into a track

on the rear cabinet wall.

To remove:

Tilt the shelf up at the front.

Lift the support off and out of the track.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

NOTE: The shelf to the right of the track is

designed to hook into the right-hand slot; the

shelf to the left is designed to hook into the

left-hand slot.

Freezer Compartment

To remove:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up and

out of the shelf supports.

To replace:

Holding the shelf diagonally, insert the

left end of the shelf into the center of

the shelf supports on the side wall.

Insert the right end of the shelf into

the shelf supports on the side wall.

Rest each end of the shelf on the

bottom of the shelf supports.

Lift up

and out

Tilt up

7

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

Adjustable Humidity Crisper

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Snack Pan

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position, and lift out.

About the crispers and pans. ge.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

8

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Removing the glass cover

Removing the frame

About crisper removal.

Not all features are on all models.

Crisper Removal

Unload the bottom shelf before attempting to

remove the storage drawers.

To Remove:

Lift the drawers up slightly while pulling

them past the stop location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

To remove the glass cover:

Remove the glass, then the frame. When

replacing the glass, push the front edge

firmly into the frame.

Push up the glass cover at the rear.

Slide the glass cover backwards until the

front edge comes out of the frame.

Rotate the side of the glass cover up.

Remove the glass cover.

To remove the frame:

Lift up the front of the frame using

both hands.

Slide the frame forward.

Rotate the side of the frame up.

Remove the frame.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

9

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Power switch model

There are 2 types of icemakers:

About the automatic icemaker. ge.com

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Automatic Icemaker (on some models)

The icemaker will produce approximately

3 to 3

1

⁄2 lbs. of ice in a 24-hour period,

depending on the freezer compartment

temperature, room temperature, number

of door openings and other use conditions.

There are two types of icemakers: power

switch models and feeler arm models.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off) or move the

feeler arm to the STOP (up) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the I (on) position or move the feeler arm to

the ON (down) position. On power switch

models, the green light will come on.

The icemaker will fill with water when it

cools to 15°F. A newly-installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

Once the icemaker starts to make ice,

it may take up to 48 hours to fill the bin,

depending on the temperature settings

and number of door openings.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale, shrink or

fuse together.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to O (off) and remove the cubes.

Set the power switch to I (on) to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Icemaker Accessory Kit

If your refrigerator did not already come

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for the

specific icemaker kit needed for your model.

This refrigerator will accept accessory icemaker IM4A or IM6. Use instruction sheet L

supplied in the kit for assembly inside freezer compartment.

To facilitate installation of an icemaker kit, the following parts are included with your

refrigerator:

Part Part Number

Ice Fill Cup WR29X10074

Ice Fill Tube WR17X12339

Ice Fill Tube Seal WR17X12337

NOTE: It is important that you DO NOT discard these parts, as they will be needed if

you plan to install accessory icemaker kit IM4A or IM6.

10

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim. Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean. Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with

a commercially available stainless steel

cleaner. Do not use appliance wax or polish

on the stainless steel.

Do not wipe the refrigerator with a soiled dish cloth

or wet towel. These may leave a residue that

can erode the paint. Do not use scouring pads,

powdered cleaners, bleach or cleaners containing

bleach because these products can scratch and

weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning. If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Thoroughly rinse

and wipe dry.

Avoid cleaning cold glass shelves (on some models)

with hot water because the extreme temperature

difference may cause them to break. Handle glass

shelves carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

Do not clean with any products containing detergent,

bleach or ammonia. They may damage the

refrigerator.

Condenser

There is no need for routine condenser

cleanings in normal home operating

environments. However, in environments

that may be particularly dusty or greasy, the

condenser should be cleaned periodically

for efficient refrigerator operation.

For models with a base grille, the grille must

be removed in order to clean the condenser.

To remove the base grille:

Grasp it about 6″ from each end and pull

its bottom edge toward you.

To replace the base grille:

Insert the tops of the metal clips into the

oval vents, making sure one of the plastic

tabs on the back of the grille goes into each

of the oval vents. Then push the bottom of

the grille forward until it snaps into place.

Cleaning the condenser:

Sweep away or vacuum up dust.

For models with a base grille, reach the

condenser by inserting a brush or vacuum

hose into the oval holes.

For models without a base grille, reach the

condenser by inserting a brush or vacuum

hose under the bottom of the refrigerator.

For best results, use a brush specially

designed for this purpose. It is available

at most appliance parts stores.

Behind the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

BEFORE moving the refrigerator away from the wall,

be sure to adjust the leveling legs up. (See Rollers

and Leveling Legs.)

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure you

don’t roll over the power cord or icemaker supply line

(on some models).

11

ge.com

Preparing for Vacation

For long vacations or absences, remove

food and unplug the refrigerator. Move

the refrigerator control to the 1 (off) position

and clean the interior with a baking soda

solution of one tablespoon (15 ml) of

baking soda to one quart (1 liter) of water.

Leave the doors open.

Set the icemaker power switch to the O (off)

position or move the feeler arm to the STOP

(up) position (depending on model) and

shut off the water supply to the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

Preparing to Move

Secure all loose items such as grille,

shelves and drawers by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright position

during moving.

Replacing the light bulb.

Setting either or both controls to 1 (off) does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

CAUTION: Light bulb may be hot.

Unplug the refrigerator.

The bulb is located at the top of the

compartment near the opening.

Replace with an appliance bulb of

the same or lower wattage.

Plug the refrigerator back in.

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation Instructions

12

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

If you have questions, call 1.800.GE.CARES or visit our Website at: ge.com

Installation

Refrigerator

Instructions

Models GTH21 and GTL21

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 1/8″ (3 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

If the refrigerator is to be installed next to a wall on the

hinge side, allow 5/16″ (8 mm) door clearance.

CLEARANCES

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE water

supply kit (containing tubing, shutoff valve, fittings

and instructions) is available at extra cost from your

dealer or by visiting our Website at ge.com or Parts

and Accessories, 800.626.2002.

WATER SUPPLY TO THE ICEMAKER

(ON SOME MODELS)

Rollers allow you to move the refrigerator away from the

wall for cleaning.

Leveling Legs near each front corner of the refrigerator,

next to the rollers, should be adjusted if any of the

following occurs:

• Refrigerator wobbles due to front roller not being firmly

positioned on the floor.

• Door(s) do not close easily when opened to 45°.

NOTE:

• BEFORE moving the refrigerator away from the wall,

be sure to turn the leveling legs counterclockwise so that

the weight of the refrigerator is fully transferred to the

front rollers.

• The refrigerator will not be level from front to back. It

will have a slight backward tilt for proper door-closing.

To adjust the leveling legs,

turn the two front leveling

legs clockwise to raise the

front of the refrigerator and

counterclockwise to lower it.

ROLLERS AND LEVELING LEGS

Clockwise to raise

refrigerator

PREPARE FOR INSTALLATION

Inside the freezer, loosen the two mounting screws,

but do not screw them all the way out. If your model

does not have the screws already in the freezer wall,

look for two plug buttons. Remove the plug buttons

and insert the two Phillips head screws. The screws

should extend approximately 1/2″ (13mm) out

from the freezer wall.

3

BEFORE YOU BEGIN

Read each step thoroughly before proceeding.

•

CAUTION – Unplug the

Refrigerator. To eliminate the danger

of electric shock during installation,

you must unplug the refrigerator from

its electrical outlet.

Flat blade and Phillips

screwdrivers

Pliers

TOOLS YOU WILL NEED

REMOVE THE OUTLET COVER

• Remove the outlet cover

with a flat-blade screwdriver.

2

SET POWER SWITCH TO O (off)

Set the icemaker power switch to O (off). Leave

the power switch in the O (off) position until the

refrigerator is connected to the water supply to

prevent premature operation.

4

Power

Switch

INSTALL FILL TUBE

• If the refrigerator already has a

water tube inlet on the back of the

refrigerator, go to Step 2.

• Remove and discard the white plug

from the lower left back corner of

the freezer wall.

• Go to the back of the refrigerator. Find the small

label in the upper right hand corner and peel it

off. Then discard the label.

• Peel one side of the paper away

from the water fill tube seal, slide

the seal along the tube and affix

to the back side of the water

tube inlet flange.

• Remove the adhesive

backing on the opposite side

of the water fill tube seal and

slide the tube into the hole

near the top at the back of the refrigerator. Firmly

press on the inlet to secure it to the refrigerator.

1

Hole for

wire tie

Remove

plug

(Appearance may vary)

13

Side

Back

Seal

Mounting

screws

Installation Instructions

PARTS INCLUDED

1

3

2

NO. DESCRIPTION QUANTITY

1 Water Fill Tube 1

2 Ice Fill Guide 1

3 Water Fill Tube Seal 1

ICEMAKER INSTALLATION INSTRUCTIONS

14

7

PLUG IN THE ICEMAKER

Holding the icemaker in place, insert the icemaker

power cord plug into the socket on the back wall,

making sure the prongs and holes are matched.

Press the plug firmly into the socket. Lock the plug

in place by clipping the restraints onto each side of

the plug. Make sure the restraints click into place.

6

INSTALL THE ICE BUCKET

Place the ice bucket under the icemaker.

Make sure the icemaker power switch is in the

O (off) position.

8

INSTALL THE ICEMAKER FILL CUP

Install the icemaker fill cup (side-mounted) into the

icemaker as shown.

5

MOUNT THE ICEMAKER

• Lift the icemaker so the fill tube extension fits in

the fill cup opening. Hang the icemaker on the

two screws.

Make sure:

• The power cord is still firmly in the socket.

• The fill tube extension extends into the

fill cup opening at the back of the icemaker.

(Check the rear of the refrigerator to make sure

the fill tube has not been pushed out of the back

of the refrigerator).

• The icemaker mounting screws are located in the

uppermost position of the mounting slots.

THEN SECURELY TIGHTEN THE ICEMAKER

MOUNTING SCREWS.

Installation Instructions

REMOVE THE COVER

Use a Phillips head screwdriver to remove the

compressor compartment access cover. This

requires removing six screws which attach the

cover to the back of the refrigerator case.

Be sure to save the screws as the access cover must

be reinstalled later to ensure your refrigerator will

function properly.

9

Icemaker

fill cup

Fill tube

extension

Fill cup

opening

Ice bucket

ICEMAKER INSTALLATION INSTRUCTIONS (CONT.)

15

Installation Instructions

ATTACH THE WATER VALVE

• Locate the female connector plug. Plug the

female connector onto the male terminals on

the water valve. Either wire can go on either

terminal.

10

• Fasten the water valve to the cabinet by driving

the Phillips head screw from the kit into the hole

in the cabinet leg.

Female

connector

Male

terminals

Phillips head

screw

12

CONNECT THE WATER LINE

• Make sure there is enough plastic water line to

extend from the water valve to well into the

water tube inlet. Cut off any excess tubing.

• Squeeze the ends of the hose clamp from the

kit with pliers and slide the clamp over the water

tube inlet.

• While still squeezing the clamp, insert the plastic

water line into the inlet as far as it will go

(approximately 1″ [25 mm]).

• Then slide the clamp downward to capture the

plastic water line in place.

• Make sure the fill tube is aimed down.

Water tube

inlet

INSTALL WATER LINE CLAMP

• Attach the metal water line clamp (strain relief)

to the refrigerator. Drive the screw from the kit

through the clamp at the indent into the back

of the cabinet.

• The metal clamp is for the house water line (see

the Water Line Installation Instructions). It is not

to be used for the tubing from the water valve up

to the icemaker.

11

Screw

Strain

relief

Hose clamp

ROUTE AND ATTACH THE

PLASTIC WATER LINE

• Fasten the plastic water line to the back

of the cabinet with adhesive-backed fasteners,

spacing the fasteners as shown to take up slack

in the line.

13

Adhesive-backed fasteners

for plastic water line

16

Installation Instructions

15

ATTACH WARRANTY LABEL

A label is provided with this kit to record the date

of installation for warranty purposes. Apply it to the

back of the refrigerator. The icemaker installation

inside the freezer is now complete.

WATER VALVE INSTALLED

Refer to the Water Line Installation Instructions

for connection to the home water supply. After

water line installation is completed, set the

icemaker power switch to I (on).

The icemaking cycle will not begin until the icemaker

and freezer compartment reach operating temperature,

then icemaking will begin automatically.

14

ICEMAKER INSTALLATION INSTRUCTIONS (CONT.)

17

INSTALLING THE WATER LINE

(ON SOME MODELS)

Recommended copper water supply kits are WX8X2,

WX8X3 or WX8X4, depending on the amount of

tubing you need. Approved plastic water supply lines

are GE SmartConnect

™

Refrigerator Tubing

(WX08X10002, WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse

Osmosis Water System, the only approved installation

is with a GE RVKit. For other reverse osmosis water

systems, follow the manufacturer’s recommendations.

This water line installation is not warranted by the

refrigerator or icemaker manufacturer. Follow these

instructions carefully to minimize the risk of expensive

water damage.

Water hammer (water banging in the pipes) in house

plumbing can cause damage to refrigerator parts and

lead to water leakage or flooding. Call a qualified

plumber to correct water hammer before installing the

water supply line to the refrigerator.

To prevent burns and product damage, do not hook

up the water line to the hot water line.

If you use your refrigerator before connecting the

water line, make sure the icemaker power switch is in

the O (off) position (on power switch models) or the

feeler arm is in the STOP (up) position (on feeler arm

models).

Do not install the icemaker tubing in areas where

temperatures fall below freezing.

When using any electrical device (such as a power

drill) during installation, be sure the device is double

insulated or grounded in a manner to prevent the

hazard of electric shock, or is battery powered.

All installations must be in accordance with local

plumbing code requirements.

BEFORE YOU BEGIN

Installation Instructions

WHAT YOU WILL NEED

• Copper or GE SmartConnect

™

Refrigerator Tubing

kit, 1/4″ outer diameter to connect the refrigerator

to the water supply. If using copper, be sure both ends

of the tubing are cut square.

To determine how much tubing you need: Measure

the distance from the water valve on the back of the

refrigerator to the water supply pipe. Then add 8′

(2.4 m). Be sure there is sufficient extra tubing to

allow the refrigerator to move out from the wall

after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are

available in the following lengths:

2′ (.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times. Certain

types of plastic will crack or rupture with age and cause

water damage to your home.

18

INSTALLING THE WATER LINE (CONT.)

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

800.626.2002.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4 ″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing to

the shutoff valve and the refrigerator water valve.

OR

• If you are using a GE SmartConnect

™

Refrigerator

Tubing kit, the necessary fittings are preassembled to

the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

Installation Instructions

SHUT OFF THE MAIN WATER

SUPPLY

Turn on the nearest faucet long enough to clear

the line of water.

Install the shutoff valve on the nearest frequently used

drinking water line.

1

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom, to

avoid drawing off any sediment from the water pipe.

CHOOSE THE VALVE LOCATION

2

Drill a 1/4″ hole in the water pipe (even if using a

self-piercing valve), using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

3

19

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand-tight; then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

CONNECT THE TUBING

TO THE VALVE

7

Turn the main water supply on and flush out the

tubing until the water is clear.

Shut the water off at the water valve after about

one quart (1 liter) of water has been flushed

through the tubing.

FLUSH OUT THE TUBING

8

Installation Instructions

Saddle-Type

Shutoff Valve

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

4

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

TIGHTEN THE PIPE CLAMP

5

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing

to allow the refrigerator to move out from the wall

after installation.

ROUTE THE TUBING

6

Washer

Inlet End

Pipe Clamp

Clamp Screw

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

20

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not

plugged into the wall outlet.

• We recommend installing a water filter if your

water supply has sand or particles that could clog

the screen of the refrigerator’s water valve. Install

it in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing kit, you

will need an additional tube (WX08X10002) to

connect the filter. Do not cut plastic tube to

install filter.

Remove the screws holding the right side of the

access cover. Fold back the cover.

Remove the plastic flexible cap

from the water valve

(refrigerator connection).

Place the compression nut and

ferrule (sleeve) onto the end of

the tubing as shown. On GE

SmartConnect

™

Refrigerator

Tubing kit, the nuts are already

assembled to the tubing.

Insert the end of the tubing into the water valve

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the water valve connection and

tighten compression nut until it is hand-tight;

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Fasten the tubing into the clamp provided to hold

it in a vertical position. You may need to pry open

the clamp.

CONNECT THE TUBING TO THE

REFRIGERATOR

9

Installation Instructions

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

10

Reattach the access cover.

1/4″ Compression Nut

Tubing Clamp

1/4″ Tubing

Ferrule (sleeve)

Refrigerator

Connection

SmartConnect

™

Tubing

INSTALLING THE WATER LINE (CONT.)

One of the illustrations below will look like the

connection on your refrigerator.

CONNECT THE TUBING TO THE

REFRIGERATOR (CONT.)

9

La page charge ...

GE GTL21 Manuel utilisateur

GE GTL21 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents