Evolution Power Tools rage3dbms1 Mode d'emploi

Date Published: 22 / 05 / 2017Written in UK English

Original Instructions

EN

ES

FR

EN

ES

FR

ENGLISH

Original Instructions

TABLE OF CONTENTS*

English Page 02

Español Página 38

Français Page 76

MACHINE SPECIFICATION 05

Introduction 06

Guarantee 06

Vibration 07

Intended use of this Power Tool 07

Prohibited use of this Power Tool 08

SAFETY PRECAUTIONS 08

Electrical Safety 08

General Power Tool Safety Instructions 09

Health Advice 10

Specific Safety Instructions 11

Personal Protective Equipment (PPE) 11

Safe Operation 11

Aditional Safety Advice 12

GETTING STARTED 12

Unpacking 12

Additional Accessories 13

Machine Overview 14

Assembly and Preparation 16

Operating Instructions 21

Use of Additional Accessories 32

MAINTENANCE 34

Care and Cleaning 34

Environmental Protection 36

EC Declaration of Conformities 37

*This manual is originally written in UK English.

4

www.evolutionpowertools.com

MACHINE SPECIFICATIONS

Motor UK (230V ~ 50/60 Hz)

Motor UK (110V ~ 50/60 Hz)

Motor USA (120V ~ 60 Hz)

No Load Speed

Weight

CUTTING CAPACITIES

Mild Steel Plate (Max Thickness)

Mild Steel Box Section (Max Wall Thickness)

0° Mitre / 0° Bevel Cut

45° Mitre / 45° Bevel Cut

45° Mitre / 0° Bevel Cut

0° Mitre / 45° Bevel Cut

BLADE DIMENSIONS

Diameter

Bore Diameter

Number of Teeth

Max Speed

Thickness

LASER

Laser Class

Laser Source

Laser Power

Wave Length

NOISE & VIBRATION DATA

Sound Pressure Level

Sound Power Level

Vibration Level

METRIC IMPERIAL

2000W 9A

1600W 15A

1800W 15A

2500min

-1

2500rpm

N: 19.6kg / G: 21kg N: 43lb / G: 46lb

6mm 1/4”

3mm

1/8”

320 x 80mm 12-1/2 x 3-1/8”

225 x 40mm 8-55/64 x 1-9/16”

225 x 80mm 8-55/64 x 3-1/8”

320 x 40mm 12-1/2 x 1-9/16”

255mm 10”

25.4mm 1”

28 28

2750min

-1

2750rpm

2.0mm 1/8”

Class 2

Laser Diode

1 Max mW

650nm

90 dB (A) K = 3 dB(A)

103 dB (A) K = 3 dB(A)

3.463 m/s

2

K = 1.5m/s

2

255mm 10” DOUBLE BEVEL TCT

MULTIPURPOSE SLIDING MITRE SAWS

5

www.evolutionpowertools.com

EN

ES

FR

IMPORTANT

Please read these operating and safety

instructions carefully and completely. For

your own safety, if you are uncertain about

any aspect of using this equipment please

access the relevant Technical Helpline,

the number of which can be found on

the Evolution Power Tools website. We

operate several Helplines throughout our

worldwide organization, but Technical

help is also available from your supplier.

WEB

www.evolutionpowertools.com

Congratulations on your purchase

of an Evolution Power Tools Machine.

Please complete your product registration

‘online’ as explained in the A4 online

guarantee registration leaflet included

with this machine. You can also scan the

QR code found on the A4 leaflet with

a Smart Phone. This will enable you to

validate your machine’s guarantee period

via Evolutions website by entering your

details and thus ensure prompt service

if ever needed. We sincerely thank you

for selecting a product from Evolution

Power Tools.

EVOLUTION LIMITED GUARANTEE

Evolution Power Tools reserves the right

to make improvements and modifications

to the product design without prior notice.

Please refer to the guarantee registration

leaflet and/or the packaging for details of

the terms and conditions of the guarantee.

Evolution Power Tools will, within the

guarantee period, and from the original date of

purchase, repair or replace any goods found to

be defective in materials or workmanship. This

guarantee is void if the tool being returned

has been used beyond the recommendations

in the Instruction Manual or if the machine

has been damaged by accident, neglect, or

improper service.

This guarantee does not apply to machines

and / or components which have been altered,

changed, or modified in any way, or subjected

to use beyond recommended capacities

and specifications. Electrical components

are subject to respective manufacturers’

warranties. All goods returned defective shall

be returned prepaid freight to Evolution Power

Tools. Evolution Power Tools reserves the right

to optionally repair or replace it with the same

or equivalent item.

There is no warranty – written or verbal – for

consumable accessories such as (following list

not exhaustive) blades, cutters, drills, chisels

or paddles etc. In no event shall Evolution

Power Tools be liable for loss or damage

resulting directly or indirectly from the use

of our merchandise or from any other cause.

Evolution Power Tools is not liable for any

costs incurred on such goods or consequential

damages. No officer, employee or agent of

Evolution Power Tools is authorized to make

oral representations of fitness or to waive any

of the foregoing terms of sale and none shall

be binding on Evolution Power Tools.

Questions relating to this limited guarantee

should be directed to the company’s head

oce, or call the appropriate Helpline number.

6

www.evolutionpowertools.com

VIBRATION

WARNING: When using this machine the

operator can be exposed to high levels

of vibration transmitted to the hand and

arm. It is possible that the operator could

develop “Vibration white nger disease”

(Raynaud syndrome). This condition

can reduce the sensitivity of the hand to

temperature as well as producing general

numbness. Prolonged or regular users of

mitre saws should monitor the condition

of their hands and ngers closely. If any

of the symptoms become evident, seek

immediate medical advice.

• The measurement and assessment of

human exposure to hand-transmitted

vibration in the workplace is given in:

BS EN ISO 5349-1:2001 and

BS EN ISO 5349-2:2002

• Many factors can inuence the actual

vibration level during operation e.g the

workpiece and the type and condition of

the cutter being used. Before each use,

such factors should be assessed, and where

possible appropriate working practices

adopted. Managing these factors can help

reduce the eects of vibration:

Handling

• Handle the machine with care, allowing

the machine to do the work.

• Avoid using excessive physical eort on

any of the machines controls.

Workpiece

• Consider the workpiece material;

its density, strength and rigidity.

• Consider the security, stability,

and orientation of the machine.

SAFETY LABELS & SYMBOLS

WARNING: Do not operate this machine if

warning and / or instruction labels are missing

or damaged. Contact Evolution Power Tools for

replacement labels.

NOTE: All or some of the following symbols

may appear in the manual or on the product.

Symbol Description

V

Volts

A

Amperes

Hz

Hertz

Min

-1 (RPM)

Speed

~

Alternating Current

n

o

No Load Speed

Wear Safety Goggles

Wear Ear Protection

Do Not Touch,

Keep hands away

Wear Dust Protection

CE certication

Waste electrical and

electronic equipment

Read Manual

WARNING

Laser Warning

Double Insulation Protection

CSA certication

INTENDED USE OF THIS

POWER TOOL

WARNING: This product is a Multipurpose

Sliding Mitre Saw and has been designed to

be used with special Evolution Multipurpose

blades. ONLY use blades designed for use in

this machine and / or those recommended

specically by Evolution Power Tools Ltd.

7

www.evolutionpowertools.com

EN

ES

FR

WHEN FITTED WITH A CORRECT

BLADE THIS MACHINE CAN BE

USED TO CUT:

• Wood, Wood derived products

(MDF, Chipboard, Plywood, Blockboard,

Hardboard etc),

• Wood with nails,

• 50mm mild steel box section with 4mm

wall at HB 200-220,

• 6mm mild steel plate at HB 200-220.

Note: Wood containing non galvanised nails

or screws, with care, can be safely cut.

Note: Not recommended for cutting

galvanised materials or wood with embedded

galvanised nails. For cutting stainless steel

we recommend Evolution dedicated stainless

steel blades.

PROHIBITED USE OF THIS

POWER TOOL

WARNING: This product is a Multipurpose

Sliding Mitre Saw and must only be used as

such. It must not be modied in any way,

or used to power any other equipment or

drive any other accessories other than those

mentioned in this Instruction Manual.

WARNING: This product is not intended for use

by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been

given supervision or instruction concerning the

safe use of the product by a person responsible for

their safety and who is competent in its safe use.

ELECTRICAL SAFETY

CONNECTION OF THE DOUBLE INSULATED

MAINS PLUG- UK ONLY

IMPORTANT: The wires in the mains

lead tted to this product are coloured in

accordance with the following code:

Brown: Live (L) or Red

Blue: Neutral (N) or Black

THIS PRODUCT IS DOUBLE INSULATED

AND THEREFORE DOES NOT REQUIRE A

CONNECTION TO EARTH.

• THE 3 PIN PLUG MUST COMPLY TO

BS1363/A.

• THE FUSE MUST COMPLY TO BS1362.



If for any reason the 13 amp moulded plug

tted to this product requires replacing, the

replacement must be wired in accordance with

the following instructions:

• Connect the Blue wire to the terminal

marked Neutral (N).

• Connect the Brown wire to the terminal

marked Live (L).

Ensure that the outer insulation is gripped

by the cord grip and that the wires are not

trapped when replacing the plug cover.

A 13 amp (BS1362) fuse must be tted in the plug.

Do not connect any wire to the earth pin

MARKED E on the 3 pin plug.

If in any doubt consult a qualied electrician.

There are no user serviceable parts inside

this product except those referred to in the

manual. Always refer servicing to qualied

service personnel. Never remove any part of

the casing unless qualied to do so; this unit

contains dangerous voltages.

8

www.evolutionpowertools.com

OUTDOOR USE

WARNING: For your protection if this tool is to

be used outdoors it should not be exposed to

rain, or used in damp locations. Do not place

the tool on damp surfaces. Use a clean, dry

workbench if available. For added protection

use a residual current device (R.C.D.) that will

interrupt the supply if the leakage current to

earth exceeds 30mA for 30ms. Always check

the operation of the residual current device

(R.C.D.) before using the machine.

If an extension cable is required it must be a

suitable type for use outdoors and so labelled.

The manufacturers instructions should be

followed when using an extension cable.

POWER TOOL GENERAL

SAFETY INSTRUCTIONS

(These General Power Tool Safety Instructions

are as specied in BS EN 60745-1:2009 &

EN 61029-1:2009)

WARNING: Read all safety warnings and

instructions. Failure to follow the warnings

and instructions may result in electric

shock, re and / or serious injury.

Note: This power tool should not be powered on

continuously for a long time.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) General Power Tool Safety Warnings

[Work area safety]

• Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

• Do not operate power tools in explosive

atmospheres, such as in the presence of

ammable liquids, gasses or dust. Power

tools create sparks which may ignite the

dust or fumes.

• Keep children and bystanders away

while operating power tool. Distractions

can cause you to lose control.

• Do not use this machine in an enclosed room.

2) General Power Tool Safety Warnings

[Electrical Safety]

• Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools.Unmodied

plugs and matching outlets will reduce the

risk of electric shock.

• Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

• Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

• Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

• When operating a power tool outdoors,

use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

• If operating a power tool in a damp

location is unavoidable, use a residual

current device (RCD) protected supply. Use

of an RCD reduces the risk of electric shock.

3) General Power Tool Safety Warnings

[Personal Safety].

• Stay alert, watch what you are doing and

use common sense when operating a

power tool. Do not use a power tool while

you are tired or under the inuence of

drugs, alcohol or medication. A moment

of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment.

Always wear eye protection to prevent

injury from sparks and chippings.

Protective equipment such as dust masks,

non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions

will reduce personal injuries.

9

www.evolutionpowertools.com

EN

ES

FR

• Prevent unintentional starting. Ensure

the switch is in the o-position before

connecting to power source and or

battery pack, picking up or carrying the

tool. Carrying power tools with your nger

on the switch or energising the power tools

that have the switch on invites accidents.

• Remove any adjusting key or wrench

before turning the power tool on. A

wrench or key left attached to a rotating part

of a power tool may result in personal injury .

• Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

• Dress properly. Do not wear loose

clothing or jewelry. Keep your hair,

clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair

can be caught in moving parts.

• If devices are provided for the connection

of dust extraction and collection facilities,

ensure that these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

• When cutting metal, gloves should be worn

before handling to prevent from getting burnt

from hot metal.

4) General Power Tool Safety Warnings

[Power tool use and care]

• Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job better

and safer at a rate for which it was designed.

• Do not use the power tool if the switch

does not turn it ON or OFF. Any power

tool that cannot be controlled with the

switch is dangerous and must be repaired.

• Disconnect the power tool from the

power source and/or battery pack from

the power tool before making any

adjustments, changing accessories, or

storing power tools. Such preventative

safety measures reduce the risk of starting

the power tool accidentally.

• Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

Instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

• Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of moving parts and any other

condition that may aect the power tools

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

• Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations dierent from those intended

could result in a hazardous situation.

5) General Power Tool Safety Warnings

[Service]

• Have your power tool serviced by a

qualied repair person using only identical

replacement parts. This will ensure that the

safety of the power tool is maintained.

HEALTH ADVICE

WARNING: If you suspect that paint on surfaces

in your home contains lead seek professional

advice. Lead based paints should only be removed

by a professional and you should not attempt

to remove it yourself. Once the dust has been

deposited on surfaces, hand to mouth contact can

result in the ingestion of lead. Exposure to even

low levels of lead can cause irreversible brain and

nervous system damage. The young and unborn

children are particularly vulnerable.

WARNING: Some wood and wood type

products, especially MDF (Medium Density

Fibreboard), can produce dust that may be

hazardous to your health. We recommend the

10

www.evolutionpowertools.com

use of an approved face mask with replaceable

lters when using this machine, in addition to

using the dust extraction facility.

MITRE SAW SPECIFIC SAFETY

The following specic safety instructions for

Mitre Saws are based on the requirements of

EN 61029-2-9:2012+A11.

BLADE SAFETY

WARNING: Rotating Saw Blades are extremely

dangerous and can cause serious injury and

amputation. Always keep ngers and hands at least

150mm away from the blade at all times. Never

attempt to retrieve sawn material until the cutting

head is in the raised position, the guard is fully

closed and the saw blade has stopped rotating.

Only use saw blades that are recommended

by the manufacturer and as detailed in this

manual and that comply with the requirements

of EN 847-1

Do Not use saw blades that are damaged or

deformed as they could shatter and cause serious

injury to the operator or bystanders.

Do Not use saw blades that are manufactured

from high speed steel (HSS).

If the table insert becomes damaged or worn it

must be replaced with an identical one available

from the manufacturer as detailed in this manual.

PERSONAL PROTECTIVE

EQUIPMENT PPE

Hearing protection should be worn in order to

reduce the risk of induced hearing loss.

Eye protection should be worn in order to

prevent the possibility of the loss of sight from

ejected chippings.

Respiratory protection is also advised as some

wood and wood type products especially MDF

(Medium Density Fibreboard) can produce

dust that can be hazardous to your health. We

recommend the use of an approved face mask

with replaceable lters when using this machine

in addition to using the dust extraction facility.

Gloves should be worn when handling blades

or rough material. Heat resistant gloves should

be worn when handling metallic materials

which may be hot. It is recommended that saw

blades should be carried in a holder wherever

practicable. It is not advisable to wear gloves

when operating the mitre saw.

SAFE OPERATION

Always ensure that you have selected the correct

saw blade for the material being cut. Do Not use

this mitre saw to cut materials other than those

specied in this Instruction Manual.

When transporting a mitre saw ensure that

the cutting head is locked in the 90 degree

down position (if a sliding mitre saw ensure

that the slide bars are locked). Lift the

machine by gripping the outer edges of the

base with both hands (if a sliding mitre saw,

transport using the handles provided). Under

no circumstances shall the machine be lifted or

transported using the retractable guard or any

part of its operating mechanism.

Bystanders and other colleagues must be kept

at a safe distance from this saw. Cut debris can,

in some circumstances, be ejected forcibly

from the machine, posing a safety hazard to

people standing nearby.

Before each use check the operation of the

retractable guard and its operating mechanism

ensuring that there is no damage, and that all

moving parts operate smoothly and correctly.

Keep the work bench and oor area clear of all

debris including sawdust, chips and o-cuts.

Always check and ensure that the speed

marked on the saw blade is at least equal to

the no load speed marked on the mitre saw.

Under no circumstances shall a saw blade be

used that is marked with a speed that is less than

the no load speed marked on the mitre saw.

Where it is necessary to use spacer or reducing

rings these must be suitable for the intended

11

www.evolutionpowertools.com

EN

ES

FR

purpose and only as recommended by the

manufacturer.

If the mitre saw is tted with a laser it shall not

be replaced with a dierent type. If the laser

fails to operate it shall be repaired or replaced

by the manufacturer or his authorised agent.

The saw blade shall only be replaced as

detailed in this Instruction Manual.

Never attempt to retrieve o-cuts or any other

part of the work piece until the cutting head is

in the raised position, the guard is fully closed

and the saw blade has stopped rotating.

PERFORM CUTS CORRECTLY

AND SAFELY

Wherever practicable always secure the work

piece to the saw table using the work clamp

where provided.

Always ensure that before each cut the mitre

saw is mounted in a stable position.

If needed the mitre saw can be mounted on a

wooden base or work bench or attached to a

mitre saw stand as detailed in this Instruction

Manual. Long work pieces should be

supported on the work supports provided or

on appropriate additional work supports.

WARNING: the operation of any mitre saw can

result in foreign objects being thrown towards

your eyes, which could result in severe eye

damage. Before beginning power tool operation,

always wear safety goggles or safety glasses with

side shield or a full face shield when needed.

WARNING: If any parts are missing, do not

operate your mitre saw until the missing parts

are replaced. Failure to follow this rule could

result in serious personal injury.

ADDITIONAL SAFETY ADVICE

CARRYING YOUR MITRE SAW

Safety Advice

• Although compact, this Mitre Saw is heavy.

To reduce the risk of back injury,

get competent help whenever you

have to lift the saw.

• To reduce the risk of back injury, hold the tool

close to your body when lifting. Bending your

knees so you can lift with your legs, not your

back. Lift by using the handhold areas at each

side of the machines base.

• Never carry the Mitre Saw by the power

cord. Carrying the Mitre Saw by the power

cord could cause damage to the insulation

or the wire connections resulting in electric

shock or re.

• Before moving the Mitre Saw tighten the

mitre and bevel locking screws and the

sliding carriage locking screw to guard

against sudden unexpected movement.

• Lock the Cutting Head in its lowest position.

Ensure that the Cutting Head Locking Pin is

completely engaged in its socket.

WARNING: Do not use the blade guard as a

‘lifting point’. The power cord must be removed

from the power supply before attempting to

move the machine.

• Lock the Cutting Head in the down position

using the Cutting Head Locking Pin.

• Loosen the Mitre Angle Locking Screw. Turn

the table to either of its maximum settings.

• Lock the table in position using the

Locking Screw.

• Use the two carry handle cut-outs machined

into either side of the machine base,

to transport the machine.

Place the saw on a secure stationary work

surface and check the saw over carefully.

Check particularly the operation of all the

machines safety features before attempting

to operate the machine.

GETTING STARTED - UNPACKING

CAUTION: This packaging contains sharp

objects. Take care when unpacking. This

machine could require two persons to lift,

12

www.evolutionpowertools.com

assemble and move this machine. Remove

the machine, together with the accessories

supplied from the packaging.

Check carefully to ensure that the machine

is in good condition and account for all the

accessories listed in this manual. Also make

sure that all the accessories are complete. If any

parts are found to be missing, the machine and

its accessories should be returned together in

their original packaging to the retailer.

Do not throw the packaging away; keep it safe

throughout the guarantee period. Dispose

of the packaging in an environmentally

responsible manner. Recycle if possible. Do

not let children play with empty plastic bags

due to the risk of suocation.

ITEMS SUPPLIED

Description Qty

Instruction Manual

(Operations)

1

Hold Down Clamp 1

Hex Key 5mm

(Blade Change)

1

Multipurpose Blade 1

ADDITIONAL ACCESSORIES

In addition to the standard items supplied with

this machine, other accessories are available

to enhance its performance. These include the

following items:

Description Part N°

Specialist cutting blades

(use only Evolution Blades

with this machine)

Specific to

blade type

Dust Collection Bag EV3DBS202

Workpiece Support Bars EV3DBS76

End Stop

(Repetitive Cutting)

EV3DBSM3

UNLATCHING AND RAISING

THE CUTTING HEAD

WARNING: To avoid serious injury, NEVER

perform the unlocking or locking procedure

unless the saw is OFF and the blade stopped.

To Release the Cutting Head from the

Locked Down position:

• Gently press down on the Cutting Handle.

• Pull out the head latching pin (Fig. A) and

allow the Cutting Head to rise to its upper

position. (Step 1 & 2)

• The Cutting Head will automatically rise to

the upper position once it is released from

the locked down position. (Step 3)

• It will automatically lock in the upper position.

If Release is Dicult:

• Gently rock the Cutting Head up and down.

• At the same time twist the Head Latching

Pin clockwise and pull outwards.

Step 3

Step 2

Step 1

Fig. A

13

www.evolutionpowertools.com

EN

ES

FR

OVERALL VIEW OF DOUBLE BEVEL MITRE SAW

1. ON/OFF TRIGGER SWITCH

2. BLADE GUARD LOCKING TRIGGER

3. CUTTING HANDLE

4. DUST BAG (Optional Accessory)

5. TABLE TOP

6. ROTARY TABLE

7. LOWER BLADE GUARD

8. UPPER BLADE GUARD

9. BLADE

10. MITRE HANDLE

11. SLIDE LOCKING SCREW

12. BEVEL ANGLE SCALE

1

2

5

6

7

8

9

10

3

4

14

www.evolutionpowertools.com

OVERALL VIEW OF DOUBLE BEVEL MITRE SAW

13. POSITIVE STOP LOCKING LEVER

14. FENCE

15. HEAD LATCHING PIN

16. MOUNTING HOLE

17. MOTOR COVER

18. MITRE ANGLE SCALE

19. RETAINING CLIP

20. ARBOR LOCK

21. EXTENSION (Optional Accessory)

22. REPEAT STOP (Optional Accessory)

23. SLIDE SHAFT ADJUST SCREW

17

15

11

12

23

14

1618

13

14

19

20

2221

15

www.evolutionpowertools.com

EN

ES

FR

16

www.evolutionpowertools.com

ASSEMBLY AND PREPARATION

WARNING: Always disconnect the saw from the power source

before making any adjustments.

NOTE: It is recommended that all instructions are always read

before operating.

PERMANENTLY MOUNTING THE MITRE SAW

To reduce the risk of injury from unexpected saw movement,

place the saw in the desired location either on a workbench

or other suitable machine stand. The base of the saw has four

mounting holes through which suitable bolts (not supplied)

can be placed to secure the miter saw. If the saw is to be used

in one location, permanently fasten it to the workbench using

appropriate fastenings (not supplied). Use locking washers and

nuts on the underside of the workbench. (Fig. 1)

• To avoid injury from ying debris, position the saw so

that other people or bystanders cannot stand too close

(or behind) it.

• Locate the saw on a rm, level surface where there is plenty

of room for handling and properly supporting the workpiece.

• Support the saw so the machine table is level and the saw

does not rock.

• Bolt or clamp the saw securely to its support stand or

workbench.

FOR PORTABLE USE:

• Mount the saw on a 18mm thick piece of plywood or

MDF (800mm x 500mm (31-1/2” x 19-7/10”) min size

recommended) using appropriate fastenings (not supplied).

• It may be necessary to countersink the washers, nuts, etc. to

the underside of the plywood or MDF mounting board to

avoid an uneven work surface.

• Use G-clamps to attach the mounting board to the work

surface. (Fig. 2)

NOTE: Some machines are tted with a rear stabilizing arm

found just below the Bevel Pivot.

If so tted, this arm should be deployed/withdrawn from the

base, particularly if the machine is to be used free standing

on a work bench. (Fig. 3). This arm will provide extra stability

to prevent the machine from toppling in the event of sudden

release of the Cutting Head.

Fig. 1

1) Hex headed bolt

2) Spring washer

3) Flat washer

4) Mitre saw base

5) Workbench

6) Flat washer

7) Spring washer

8) Hex nut

9) Lock nut

Fig. 2

Fig. 3

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

17

www.evolutionpowertools.com

EN

ES

FR

HOLD DOWN CLAMP (Fig. 4)

Two sockets (one either side) are incorporated into the rear of

the machines fence. These sockets are for positioning the Hold

Down Clamp.

• Fit the clamp to the retaining socket that best suits the

cutting application, ensuring that it is fully pushed down.

• Tighten the fence thumbscrew to lock the pillar of the clamp

into the fence socket.

• Place the workpiece to be cut onto the saw table, against the

fence and in the desired position.

• Adjust the clamp using the thumbscrews and hand-wheel so

that it securely holds the workpiece to the saw table.

Conduct a ‘dry run’ with the power disconnected. Ensure that the

Hold Down Clamp does not interfere with the path of the blade, or

with the path of any other part of the Cutting Head as it is lowered

THE LASER

This machine is equipped with a Laser Cutting Guide. This allows

the operator to preview the path of the blade through the

workpiece. The ON/OFF switch for the Laser Guide is positioned

on the right hand side of the machine, below the transmission

casing. (Fig 5)

Avoid direct eye contact with the laser beam, and do not use on

material that could reect the laser beam.

Never look into the laser beam. Direct laser beam may injure

your eyes.

WARNING: Do not stare directly at the laser beam.

A hazard may exist if you deliberately stare into the beam.

Please observe all of the following safety rules.

• The laser beam must not be deliberately aimed at personnel

and must be prevented from being directed towards the eyes

of a person.

• Always ensure that the laser beam is used only on workpieces

that have non-reective surfaces, i.e natural wood or matt

surfaces etc.

• Never exchange the laser module assembly for a dierent

type or class of laser.

• Repairs to the laser module must only be conducted by

Evolution Power Tools or their authorized agent.

Fig. 4

Fig. 5

18

www.evolutionpowertools.com

LASER ADJUSTMENT

WARNING: At no time during this procedure should the motor

be started.

To check laser alignment:

• Place a piece of cardboard, or similar, onto the rotary table of

the machine.

• With the carriage slide in the rearmost position, lower the Cutting

Head so that a blade tooth makes a mark in the cardboard.

• Allow the Cutting Head to rise, and then repeat the above

with the carriage slide in an approximate mid- way position.

• Again repeat, but with the carriage slide moved to its most

forward position.

• With the Cutting Head raised, turn on the laser and slide

the Cutting Head backwards and forwards to observe if the

projected laser beam is in line with the marks previously made:

• Beam is aligned with the marks =

No further action required.

• Beam is not parallel with the marks =

Follow section A

• Beam is parallel but not aligned with the marks =

Proceed to B

A. If the laser beam is not parallel to the marks proceed as follows:

• Untighten the clamping screw (Fig. 6, a)

• Carefully rotate the laser module, (Fig. 6, b) until the line is

parallel with the marks in the cardboard.

• Re-tighten the clamping screw.

• Recheck the alignment.

B. If the laser beam is parallel with the marks, but not going

through them:

• Slacken the two screws. (Fig. 7, c)

• The laser mounting block can now be moved sideways to

align the laser beam with the marks made in the cardboard.

• When the laser beam is in the correct place,

re-tighten the two screws.

• Repeat procedure ‘A’ to check alignment.

NOTE: The above adjustments & alignments should be checked

on a regular basis to ensure laser accuracy.

Fig. 6

(a) - Clamping screw

(b) - Laser unit

Fig. 7

(a)

(c)(c)

(b)

19

www.evolutionpowertools.com

EN

ES

FR

NOTE: The following WARNING labels may be found on this

machine:

LASER RADIATION DO NOT STARE INTO THE

BEAM

CLASS 2 LASER PRODUCT

CLASS 2 LASER PRODUCT LASER RADIATION AVOID

DIRECT EYE CONTACT LASER SAFETY

The Laser guide line used in this product uses a class II Laser

with a maximum power output of 1.5mW at a wave length of

between 635 and 670nm. These lasers do not normally present

an optical hazard, although staring at the beam may cause

temporary ash blindness.

WARNING: Do not stare directly at the Laser beam. The laser

must be used and maintained as detailed in this manual. Never

intentionally aim the laser beam at any person and prevent it

from being directed towards the eye, or an object other than

the workpiece. Always ensure that the laser beam is directed at

the workpiece only when it is located on the mitre saw table.

Never direct the laser beam onto any bright, shiny reective

surface, as the laser beam could be reected back towards the

operator. Do not change the laser unit for any other type.

Do not tamper with the laser unit. Only touch the unit when

making adjustments. Repairs to the laser shall only be carried

out by an authorised service centre.

THE LASER GUIDE LINE

The projected laser guide line shows the path of the blade

during a cut.

To use the laser guide for a known angle (e.g. 45

0

):

• Mark the cut required on the workpiece using a pencil etc.

• Set the saw to the cutting angle required (45

0

) and lock into

position using the mitre locking handle and/or the positive

stop locking lever.

• Switch on the laser beam.

• Position the workpiece on the rotary table and against the fence.

• Slide the workpiece into position until the pencil line on the

workpiece and the projected laser line exactly match.

• Clamp the workpiece into position using the hold down clamp.

• Proceed to make the cut.

20

www.evolutionpowertools.com

To use the laser guide for an unknown angle:

• Mark the position of the cut to be made on the workpiece

using a pencil etc.

• Place the workpiece on the rotary table and against the fence.

• Adjust the mitre saw to give the approximate angle of cut.

Do not tighten the mitre lock handle at this stage.

• Slowly slide the workpiece backwards and forwards along

the fence, whilst at the same time slowly adjusting the angle

of the rotary table.

• Stop when the projected laser line and pencil line on the

workpiece match exactly.

• Tighten the mitre lock handle to lock the rotary table in place.

• Secure the workpiece with a hold down clamp.

• Recheck the alignment.

• When satised that alignment is accurate proceed to make

the cut.

The Laser Lens cap (if tted)

If tted the laser lens cap is a simple push t onto the front of

the laser unit.

If it becomes damaged or opaque for any reason it can be replaced.

Carefully pull the lens from the laser unit and replace with a new lens.

DEPTH STOP (Fig. 8)

Use of the depth stop allows the operator to cut slots in the

workpiece.

The downward travel of the Cutting Head can be set so that

the saw blade does not completely cut through the workpiece.

NOTE: When using the Depth Stop it is advisable that the depth

of cut is checked using a scrap piece of timber to ensure that

the slot cut is correct.

By making a cut in the workpiece, and then repeating the cut

but with the workpiece slightly repositioned to the left or right,

it is possible to perform trenching cuts.

To use the depth stop:

• Loosen the locking wing nut. (a)

• Adjust the thumb knob (b) to limit the saw heads travel to

the required depth.

• Once set to the desired depth, tighten the wing nut (a)

against the retaining bracket to lock the depth stop and

ensure that there is no movement.

Fig. 8

(a)

(b)

La page charge ...

Evolution Power Tools rage3dbms1 Mode d'emploi

Ce manuel convient également à

Evolution Power Tools rage3dbms1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents